Providing Lane Marking, Road Studs and Road Safety Measures for the Formation of internal roads at Future Mobility Park (FMP),SIPCOT Industrial Park, Shoolagiri

CIVIL WORKS

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous surface Providing and laying of hot applied Thermoplastic compound 2.5mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes etc., complete complying with standard specification and as directed by SIPCOT Officers.

Road Markers / Road Stud with Lens Reflector : Providing and fixing reflective road studs of "category A" Raised pavement markers made out of poly carbonate / methyl methecrylate / ABS moulded body confirming to ASTM D 788 and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MORTH circular No RW / NH. 33023 / 10 / 97 - DO.III dt 11.06.97. The height, width and length shall not be less than 15mm, 90mm and 100mm and with minimum reflective area of 13 sq.cm on each side and the slope to the base shall be 35 +/- degree. Each reflector shall have a CIL not less than values specified in table 2 of said MORTH circular. The strength of detachment of the integrated cylindrical shanks, (of diameter not less then 19 +/- 2mm and height not less than 30+/- 2mm) from the body is to be a minimum value of 500 Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer’s recommendation and complete as directed by the engineer. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280 and confirming to IRC 35 - 2015 guidelines and MORT&H specification etc., complete complying with standard specification and as directed by SIPCOT Officers.

Rigid Median Marker : Providing fixing of Median marker double sided made of polycarbonate for impact resistance and good weather ability. Polycarbonate used for molding the median marker shall have a minimum Izod impact strength value of 600 J/m at room temperature. The impact strength of the poly carbonate should not decrease to less than 70% of its initial value on being subjected to UV weathering as per ASTM G 155 for 1000 hours or exposure to 2 years of natural weathering. The body of the median marker shall be in the form of an isosceles trapezoidal structure of length 15 cm height and width of 10 x 10 cm. The median marker shall have fluorescent yellow retro-reflective sheeting confirming to Type XI specifications as per ASTM D 4956. Area of reflective sheeting should not be less than 70 cm2. Edge of retro reflective shall be concealed using a grill/mesh/similar mechanism to prevent vandalism and sheeting pilferage. The logo of the manufacturer shall be embossed and painted in contrasting colour on both side of median marker for distinct identification etc., complete complying with standard specification and as directed by SIPCOT Officers.

Retro - Reflectorised Traffic signs (without definition board) Type - IV. Providing and Fixing of Retro - Reflectorised Cautionary, Mandatory and informatory signs (without definition board) made out of high Intensity prismatic Grade sheeting confirming to Type - IV Standard of IRC-67: 2012 and ASTM D 4956 - 09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25mm x 3mm Mild steel angle and supported on a mild steel angle post 75 x 75 x 6mm with a clear height of not less than 2.1m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67- 2012 and firmly fixed on the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 6.0cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro - Reflectro sheet shall consist of minimum coefficient of Retro-reflection as per table 6.6 of IRC 67 - 2012. The retro - reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012. etc., complete complying with standard specification and as directed by SIPCOT Officers.

90 Cm. Equilateral triangle ( Pedistrian crossing, Other sign boards )

60 Cm. Equilateral triangle ( Triangular )

60 Cm. Circular ( No overtaking, Speed limit)

80 x 60 Cm. Rectangular ( Bus stop village Boards )

60 x 45 Cm. Rectangular ( Chevron Sign )

60 x 60 Cm. (Square)

90 Cm. High Octogonal

Direction and Place Identification Signs - Type - XI (For location of black spot, curve, sharp bend, junction, ghat roads and critical zone application) : Providing and erecting Direction and Place Identification Retro - reflectorised Signs made out of Cube Corner Prismatic Grade sheeting confirming to Type - XI standards of IRC-67: 2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25mm x 3mm Mild steel angle and supported on a mild steel angle post 75x75x6mm with clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67 - 2012 and firmly fixed to the ground by means of properly designed foundation with M15 Grade cement concrete 45cm x 45cm x 60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. Micro Prismatic grade Retro Reflectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.9 of IRC 67 - 2012. The retro-reflective sheeting shall be covered under 10 year warrantee issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012.) (For location of black spot, curve, sharp bend, junction, ghat roads and critical zone applications) Rate per sqm (for sign having area more than 0.9 sqm) Type - IV etc., complete complying with standard specification and as directed by SIPCOT Officers.

Digitally Printed Retro-Reflectorized Overhead Cantilever Gantry Informatory Sign Board : Providing and fixing of Digitally Printed Retro-Reflectorized Overhead Cantilever Gantry Informatory Sign Board made out of cube corner Micro Prismatic grade sheeting of Type XI standards of IRC67 - 2012 and ASTM D 4956 - 09 specification, Digitally Printed using Latex Printer for traffic color logos/ text and laminated with clear electro-cuttable film and applied to properly prepared sign substrates, fixed over 2mm thick aluminum sheet with back supporting frame of size 50mm x 50mm x 6mm MS angle and supported on a vertical post of 300 NB (Nominal Bore) MS pipe of 12 mm thick with a ground clearance of 6meters along with 80NB (Nominal Bore) MS Pipe with 4mm thick and 40NB (Nominal Bore) MS Pipe with 3.20 mm thick support posts. The sign board should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed substructure and foundation with Reinforced Cement Concrete M20 grade column (1.25m x 1.25m x 1.90m) and footing (1.80m x 1.80m x 0.30m) with Fe 500 steel over Plain Cement Concrete M15 grade levelling course of 100 mm thick. The minimum depth of foundation shall not be less than 2.00m. 1 number of MS Base plate of size 1200mm x 1200mm x 25mm with Anchor bolts of 25mm dia and 1000mm length, 2 numbers of MS Top plates of size 900mm x 2100mm x 16mm with suitable bolts, nuts and washers, suitable numbers of MS stiffener plates of 8mm thick are to be used to hold the sign board at the bottom and top respectively including cost and conveyance of all materials, equipment, machinery and labour with all leads and lifts, loading charges and fixing the overhead cantilever sign board in position, etc., for satisfactory completion of the work as per structural and foundation drawings approved by the competent authority and as directed by the Engineer-in-charge. The micro prismatic grade retro-reflector sheet should have minimum co-efficient of Retro-reflection values as per Table 6.9 of IRC 67¬2012. The retro-reflective sheeting shall be covered under 10 years warranty issued for field performance as per IRC 67-2012 and a certified copy of 3 years outdoor exposure report shall be obtained. The warranty shall be inclusive of digitally printed logos/text/legends and their bonding to the retro-reflective sheeting . The Latex printer used for digital printing should be used with inks of low VOC emissions and should have green guard, eco logo certificates as per UL 2801 standards etc., complete complying with standard specification and as directed by SIPCOT Officers.

Digitally Printed Retro-Reflectorized Overhead Gantry Informatory Sign Board of Size 12.00 m x 1.80 m

Digitally Printed Retro-Reflectorized Overhead Cantilever Gantry Informatory Sign Board of size 5.00m x 1.80m

Sub Total of Total Amount in Column BA (ie. Qty x Unit Rate)

Added GST of 18%

Please Enable Macros to View BoQ information