Construction of Science Lab, Building for Govt. Senior Secondary School at Materni Tehsil Arki District Solan Himachal Pradesh

Earth work in Excavation by mechanical mean (Hydraulic Excavator)/Manual Means in foundation and trenches or drains (not exceeding 1.50 meter in width or 10.00 sqm on plan),including dressing of sides and ramming of bottoms, lift upto 1.50 meter, including getting out the excavated soil and disposal of surplus excavated soil as directed, with a lead of 50.00 meters.All kinds of soils/ordinary rock 50% (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the engineer -in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (To be arranged by the contractor) as per satisfaction of Engineer- in -charge through all modes of transportation including head load ,animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour ( if required ). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation and used /removed as per the direction of the Engineer - in- charge. Any loss to the public and private propriety during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respect including all incidental charges.

Filling in plinth with sand under floors including watering ramming, consolidating and dressing complete including carriage of materials upto all leads and lifts as per the direction of the Engineer-in-Charge.

Centering and shuttering including strutting, proping etc. and removal for the same concrete work including carriage of materials upto all leads and lifts as per the direction of the Engineer-in-Charge.

Foundation, footings basis of columns etc. and mass concrete.

Columns, pillars, posts and struts

Beams, cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1 metre in depth in all heights from floor.

Flat surfaces such as soffits of suspended floors,roofs, landings and the like.

Stair cases(except spiral stair cases) excluding but including preparing of the surface and finishing of the nosing upto all floor level.

Edges of slabs and breaks in floors and walls under twenty centimetre wide.

walls (any thickness) partions and the like including attached pillasters buttresses, plinth and string courses and the like.

Providing and laying damp proof course 50 mm (fifty milimeter) thick with cement concrete 1:2:4 (one cement isto two sand isto four graded stone aggregate 12.50 mm (twelve point five zero milimeter) nominal size.complete as per HP. CPWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and aplying a coat of residual petroleum bitumen of grade of VG-10 ao approved quality using 1.70 kg per square meter on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerocene oil etc.complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying cement concrete plain / reinforced concrete in open foundation complete as per drawing and technical specification clause 802,803,1202 & 1203 in PCC 1:4:8 (One cement : four sand : eight graded stone aggregate 40mm (Forty millimeter) nominal size) mechanically mixed,vibrated and curing complete complete and as per HP. PWD. specifications of 1990 volume-I. including carriage of all ,labour,equipments and materials to various location through all modes of transportation with in all leads, lifts, and other incidental charges.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering :- all work upto plinth level 1:2:4 (one cement : two sand : four graded stone aggregate 20mm twenty milimetre nominal size) and curing complete including the cost of form work with steel plates and fixed by bitumen drums in dressiest as per drawing and HP.PWD specifications as per the direction of the Engineer-in-Charge but including carriage of materials up to all leads and lifts

Providing and laying in position machine batched and machine mixed design mixed M-25 grade cement concrete for Reinforced ,using cement concrete work as per design mix, icluding pumpiing of concrete to site of laying, but excluding cost of centering, shuttering finishing and reinforcement: complete including admixtures in reccommended ptopportions as per IS :9103 to accelerate,retard setting of concrete,improve workability with out impairing strength and durability including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge. all work upto plinth level

Providing and laying in position machine batched and machine mixed design mixed M-25 grade cement concrete for Reinforced ,using cement concrete work as per design mix, icluding pumpiing of concrete to site of laying, but excluding cost of centering, shuttering finishing and reinforcement: complete including admixtures in reccommended ptopportions as per IS :9103 to accelerate,retard setting of concrete,improve workability with out impairing strength and durability including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge. .all work above plinth level upto floor five level.

Providing hoisting and fixing above plinth level upto floor five level precast reinforced cement concrete in mouldings as in cornices,window sills etc., including setting in cement mortar 1:3 (one cement isto three sand) cost of required centering, shuttering but excluding the cost of reinforcement with 1:1.50:3 (one cement isto one point five zero sand isto three graded stone aggregate 20 mm nominal size) complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge. all work above plinth level upto floor five level.

Steel reinforcement for reinforced cement concrete work including cutting /bending, binding and placing in position complete including cost of binding wire upto floor all level including carriage of materials upto all leads and lifts as per the direction of the Engineer-in-Charge.(a)Tor steel.

Brick work using common burnt clay modular bricks of class designation 7.50 (seven point five zero) in foundation and plinth in cement modular 1:6 (one cement isto six sand) using second class building bricks including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Brick work Rat trap bound using common burnt clay building bricks in super structure above plinth level upto all floor all levels in all shapes and sizes in cement mortar 1:6 (One cement : Six sand) complete . including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Brick work with common burnt clay building bricks F.P.S (Non modular) bricks of class designation 7.50 (seven point five) in super structure above plinth level upto all floor all levels in all shapes and sizes in cement mortar 1:6 (One cement isto six sand) complete . including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Half brick work using common burnt clay building bricks F.P.S. (Modular) of class designation 12.50(twelve point five zero) in super structure above plinth level upto floor five level using second class building bricks in cement mortar 1:4 ( one cement : four sand) including carriage of materials upto all leads and lifts and as per the direction of Engineer in charge.

Providing and fixing 25 mm (twenty five milimeter) thick prelaminated medium denisity fiber board exteriorr graded (grade-I) IS: 14587: 1998 marked with one side decorated and other side balancing lamination for cupboard shutters edges to be sealed with PVC edge bending top 2 mm thick of approved brand including ISI marked nickel plated bright finishing MS piano hinges conforming to IS:3818 marked with necessary screw etc. including carriage of materials within all leads and lifts.complete including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge..

Providing and fixing 18 mm (Eighteen milimeter) thick prelaminated flat pressed 3.00 (three ) layer medium denisity partical board or graded wood particle board confirming to IS: 3087 marked, with one side decorated and other side balancing lamination grade-I Type-II exterior grade IS:12823 marked in shelves with screws and fittings wherever required edge to be painted with polyurethane primer (fitting to be paid separataly . including carriage of materials within all leads and lifts.complete including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge..

Providing and fixing 35 mm (Thirty five milimetre) thick ISI marked stainless steel butt hinges with necessary screwsISI marked flush door shutters confirming to IS:2202 (two thousand two hundred two) Part -I non decorative type core of black board construction with frame Ist class hard wood and well matched commercial 3 mm (three milimeter) ply veneering with vertical grains or cross band and face veneers on both faces of shutters as per Arch. Drawing complete.and as per HP. PWD. specifications of 1990 volume-I.including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing aluminium sliding door bolts, with nuts and bolts etc. complete for all floors, including carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing aluminium tower bolts ,ISI Marked anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or Berrel type) transperent or dyed to required colour or shade, with nuts and screws etc. complete for all floors, including carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing aluminium handles, ISI Marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transperent or dyed to required colour or shade, with nuts and screws etc. complete for all floors, including carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

125mm. (One hundred twenty five milimetre)

100mm. (One hundred milimetre)

Providing and fixing aluminium hanging type floor door single rubber stopper ISI Marked anodised (anodic coating not less than grade AC 10 as per IS:1868 transparent or dyed to required colour and shade with necessary screws etc. complete as per HPPWD specification 1990 volume-I ( One ) including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 50 mm (Fifty milimeter) special quality bright finished brass cup board or ward robe nobe with four levers of approved quality including necessary screwss etc. complete as per HPPWD specification 1990 volume-I ( One ) including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 50 mm (Fifty milimeter) special quality bright finished brass cup board or ward robe nobe with four levers of approved quality including necessary screwss etc. complete as per HPPWD specification 1990 volume-I ( One ) including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing Double strip (horizontal type) special quality brass magnetic catcher of approved quality in cupboard/ward robe shutters,including fixing with necessary screws etc. complete triple strip vertical type. including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing M.S. grills of required patterns in frames of windows etc. with M.S.flats, square or round bars including priming coat with approved steel primer all complete fixed to steel windows by weldings etc.fixed to steel windows by welding etc. complete . including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing PGI sheet 1 mm (one milimeter) thick linning on existing door shutters (bath rooms and WC doors) with screws etc. complete . including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing MS tube hand rail of approved size weldeing etc. to steel ladder railing, stair case/balcony railing and similar works including one coat of red oxide priming coat complete complete . including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge..

Structural Steel work including section riveted,bolted or welded in built up sections, trusses and framed work including cutting,hoisting fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. and as per including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Sructural steel work including hollow sections riveted, bolted or welded in built up section trusses and framed work, including cutting,hoisting and fixing in position and applying priming coat of approved steel primer all complete. as per HP. PWD. Specifications of 1990 vplume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

In gratings, framed guard bars, ladders, railing, brackets and similar works.

Providing and fixing steel window and ventilator frames manufactured of frame with mild steel channel 75x40 (seventy five into forty) milimeters foer end frames and for centre frame channel section of 75x40 (seventy five into forty) milimeters with mild steel flat of 75x 4mm (sevnty five into four) milimeters incombination welded together to make one frame with making square steel section with mild steel flat of 20x4mm (twenty into four) milimeters and 12x4 mm (twelve into four milimeter)n shutters of rolled steel section F-7B (seven B) Z section including glass panes of 4 mm(four milimeter) thick in glazed panel and wire gauge of designation 85(eight five) G with wire of 0.56 mm (zero point five six) milimeters dia in wire gauge panel and fixed glazing fixed with angle and T section of 25x25x3mm (twenty five into twenty five into three) milimeters and mild steel flat of 12x4 mm (twelve into four) milimeters in sash bars duly welded of all corners and joints properly hold fast of mild steel flat 200x50x5mm (two hundred into fifty into five) milimeters duly welded of corner and joints of all steel section embeded in cement concrete block 1:3:6 (one cement :three Sand;six graded stone) 100x100x100mm (one hundred into one hundred into one hundred) stone aggregate 20mm (twenty) milimetres nominal size including providing and fixing of fittings that is handles tower bolts hooks and eyes and applying a coat of primer with red lead paint and fixing in position complete in all respect as per architectural drawingcomplete including the carriage of material within all leads and lifts and as per the direction of the Engineer-in-Charge.

Providing and fixing angle iron in door,widow,clearstory window frame manufactured from mild steel iron section of 40x40x4 mm (forty into forty into four milimeter) welded with MS flat 50x4 mm ( fifty into four milimeter) in combination welded together to make one frame including hinges,jambs,lock jamb bead and if required angle thrashold of mild steel angle including hinges,jambs,lock jamb bead,and if required angle thrashold of mild steel angle 50x25 mm (fifty into twenty five milimeter) welded or rigidly fixed by mechanical means, lugs with split and tails to each jamb including joints mitered and welded with 16x3.15 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm (fifteen into ten into ten centimeters) 1:3:6 (one cement isto three sand isto six graded crushed stone aggregate nominal size ) with provision for locking arrangment and shock absorber as specified including steel butt hinges 2.50 mm and applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer in Charge complete.as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing mild steel round holding down bolts with nuts and washers plates complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Cement concrete flooring1:2:4 ( one cement isto two course sand isto four graded stone aggregate 20 mm , (twenty milimeter) finished with a floating of neat cement,including cement slurry, but excluding the cost of nosing of steps etc. complete.as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge. 40 mm (forty milimeter) thick with 20 mm (twenty milimeter) nominal size stone aggregate.

Kota stone slab flooring over 20mm (twenty milimetre ) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab,including rubbing and polishing complete with base of cement mortar 1:4 (one cement is to four sand) complete including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge. 25 mm (Twenty five milimeter) thick.

Kota stone slab 20 mm thick (twenty milimeter) in risers of steps , skirting,dado and pillars laid on 12 mm (average) thick base of cement mortor 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and Laying Marble stone flooring with 18 mm (eighteen milimeter) thick marble stone as per sample of marble approved by the engineer in charge over 20 mm (twenty milimeter) average thick base of cement mortar 1:4 (one cement isto four sand ) laid and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing coplete.with black zebra marble. including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 10 mm (ten milimeter) thick acid and / or alkali resistant tiles in Dado/ skirtingon a bed of 12 mm (twelve milimeter) thick cement mortar 1:4 (one acid proof cement isto four coarse sand) of approved make and colour using acid and/ or alkali resisting mortar bedding and joints filled with acid and /or alkali resisting cement as per IS:4457 complete, wherever required.. including carrige of material upto all leads and lifts by all means and as per the direction of Engineer-In-charge.

Providing and fixing 10 mm (ten milimeter) thick acid and / or alkali resistant tiles in flooring on a bed of 10 mm (ten milimeter) thick cement mortar 1:4 (one acid proof cement isto four coarse sand) of approved make and colour using acid and/ or alkali resisting mortar bedding and joints filled with acid and /or alkali resisting cement as per IS:4457 complete, wherever required.. including carrige of material upto all leads and lifts by all means and as per the direction of Engineer-In-charge.

Providing and laying 40 mm (forty milimeter) thick red sand stone flooring over 20 mm (twenty m8ilimeter) average thick base of cement mortar 1:5 (one cement isto five coarse sand) with joints of 3 mm (three milimeter) thick side buttered with cement mortar 1:2 ( one cement isto two stone dust) admixed with pigment to match the shade of stone and pointing with same mortar. Red sand stone. including carrige of material upto all leads and lifts by all means and as per the direction of Engineer-In-charge.

Providing and laying Ist quality ceremic glazed floor tiles confirming to IS:15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy,bottle green,black of any size as approved by Engineer-in-Charge in skirting,risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (one cement isto three coarse sand) and jointing with grey cement slurry @ 3.30 kg per sqm including pointing in white cement mixed with pigment of machine shade complete etc. complete and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Extra for pre finished nosing to treads of stepsn of marble/ kota stone etc. complete with all accessories as required complete as per CPWD specification 1990 volume-I complete and as per the direction of the Engineer-in-Charge but including carriage of materials up to all leads and lifts .

Providing and fixing Garsa stone 12 mm thick cladding on plastered RCC surface side as on faces of Arch.masonrywalls etc. on 12 mm thick cement plaster 1:3 (one cement isto three coarse sand) and jointed with cement slurry including scaffolding etc. complete as per CPWD specification 1990 volume-I complete and as per the direction of the Engineer-in-Charge but including carriage of materials up to all leads and lifts .

Roof Covering-Providing and fixing 0.60mm ( zero point sixty milimetre) thick prepainted steel sheet in roofing TATA DURASHINE with hot dipped metallic zinc coated sheet with top coat of regular modified polyester(RNP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating to back coat of polyester of 5 (five) microns primer coating including fixing with prepainted iron J or L hooks bolts and nuts 6 mm (six milimeter) dia with prepainted limpet and rubber washers complete with all accessories as required and as per direction of the Engineer-in-Charge including carriage of materials with in all leads and lifts.

Providing and fixing M.S.(BP) black sheet 2mm (two milimeter) thick in eaves board in facia /soffits/ ceiling including cutting,fixing and, welding to steel roof members and applying a coat of red lead primer etc. complete as per (angle iron frame to be measured and paid for separetely) complete as per the instruction of Engineer in charge ( base members of steel work to be measured and paid for separately) including carriage of material in all leads and lifts :-

Providing and fixing ridges or hips 60 cm (sixty centimeter) over all with 0.60 mm (zero point sixty milimeter) ) thick prepainted steel sheets of TATA DURASHINE in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (twenty ) microns over 5 (five) microns primer coating+ back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6 mm (six milimeter) dia and prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge.0.60 mm (zero point sixty milimeter) thick sheet

Providing and fixing flushing 38 cm ( thrity eight centimetre) .overall with 0.60mm ( zero point sixty milimetre) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 Twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6mm (six milimeter) dia meter and prepainted G.I. limpetand bitumen washers complete with all accessories as required as per direction of the Engineer-in-Charge.TATA-Make.or its equavalents.

Providing and fixing 15 cm wide, 45 cm over semicircular plain GS sheet gutter with iron brackets 40x3 mm size,bolts,nuts and washers etc. including making necessary connections with rain water pipes with 0.63 mm thick zink coating not less than 275 gm/m2. including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing to the inlet mouth of rai water pipe cast iron grating 15 cm diameter and weighing not less than440 grams.etc.complete. including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing on wall face unplasticised rigid P.V.C. Rain water pipes conforming to IS: 13592 type A, including jointing with seal ring conforming to IS:5382 leaving 10 mm (ten milimeter) gap for thermal expansion. (i) Bends 87.50 degree) 110 mm diameter as required. including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing unplasticised P.V.C. pipe clips of approved design to unplasticised P.V.C. Rain water pipes by means of 50x50x50 mm hard wood plugss, screwed with MS screws of required length,including cutting brick work and fixing in cement mortae 1:4 (one cement isto four coarse sand) and making good the wall etc. complete . including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing on wall face unplasticised P.V.C. moulded fittings/accessories for unplasticised rigid P.V.C. Rain water pipes conforming to IS: 13592 type A, including jointing with seal ring conforming to IS:5382 leaving 10 mm (ten milimeter) gap for thermal expansion. (i) Bends 87.5 degree 110 mm diameter (one hundred ten milimeter) diameter as required. including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing on wall face unplasticised P.V.C. moulded fittings/accessories for unplasticised rigid P.V.C. Rain water pipes conforming to IS: 13592 type A, including jointing with seal ring conforming to IS:5382 leaving 10 mm (ten milimeter) gap for thermal expansion. (i) Shoe (Plain) 110 mm diameter as required. including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing fully perforated Gypsum plster board of size 1200x2400x12.50 mm false ceiling at all height including providing and fixing of frame work made of special sections,power pressed from MS sheets and galvanised with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm wide x1.60 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre. etc.complete (frame workto be measured and paid for separetely) as required including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 6mm thick (Six milimetre) cement fiber board as per IS:14862 plain multipurpose cement board (high pressure steam cured) with suitable secrews for cement partical board in ceiling etc.complete (frame workto be measured and paid for separetely) as required including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing flat iron brackets 50x3 mm size with necessary bolts,nuts and washers etc. for fixing GS sheets gutters with purlins. etc.complete as required including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing dome shapped grating of MS flat 25x5/6 mm square or round shape with 6mm diameter bars in dome complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and Applying birla/JK white wall care putty of 2 mm (two milimeter) thickness over plastered surface to prepare the surface even and smooth complete.including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Finishing walls with epoxy paints two or more coats at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface,etc. complete as required including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge. on steel work.

Finishing walls with epoxy paints two or more coats at all locations and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface,etc. complete . including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge..on Concrete work

Wall painting with premium acrylic emulsion paint of interior grade having low VOC (volatile organic compound) content less than 50 gms/litre (fifty grame) of approved brand and including applying additional coats wherever required to achieve even shade and colours as required complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Finishing wall with weather proof exterior grade emulsion of approved design (apexultima) or its equivelent on undecorated wall surfaces (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt and remains of loose powdered material including carriage of materials upto all leads and lifts and as per the direction of Engineer-inCharge.

Applying priming coat with primer of approved quality/brand and manufacture, having low VOC (volatile organic compound) content with ready mixed pink or grey primer on wood work(hard and soft wood) having VOC content less than 50 (fifty) grams per litre. including carriage of materials within all leads and lifts and all incidental charges and as per the direction of Engineer-in-Charge.

Painting (two or more coats) on new work over and under coat of suitable shade with ordinary paint of approved brand and manufacture with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade as required complete including entire carriage of materials within all leads llifts and as per the direction of Engineer-in-Charge and all incidental charges.White enamal paint other than white

6mm ( six milimetre ) cement plaster 1:3 ( One cement isto three fine sand ) finished with a floating coat of neat cement and thick coat of lime wash on top complete. including carriage of all labourequipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

12 mm (twelve milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto all floor level including arrses,internal rounded angles,chamfers and / or rounded angles not exceeding 30 cm (thirty centimeter) in girth and finished even and sand papered smooth in cement mortar 1:3 (One cement isto three fine sand): complete including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge

15 mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto all floor level including arrses,internal rounded angles,chamfers and / or rounded angles not exceeding 30 cm (thirty centimeter) in girth and finished even and sand papered smooth in cement mortar 1:6 (One cement isto six fine sand): complete including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge

15 mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone walls for interior plastering upto all floor level and finished even and sand papered smooth in cement mortar 1:6 (One cement isto six fine sand): complete including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15 mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto all floor level including arrses,internal rounded angles finished even and sand papered smooth in cement mortar 1:3 (One cement isto three fine sand): complete including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge

Providing and laying 60 mm (sixty milimeter) thick factory interlocking block heavy duty precast cement concrete inter locking paver blocks compacted upto M-30 grademade by block machine with strong vibratory compaction, of approved size, design and shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand,filling the joints with line sand etc..complete and including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and laying water proofing treatment in sunken portion of WCs, bath room etc. by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) first layer of slurry of cement @ 0.488 kg/ sqm mixed with water proofing cement compound @ 0.253 kg/sqm. this layer will be allowed to air cure for 4 hours.b) second layers of slutty of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. this layer will be allowed to air cure for 4 hours following with water curring for 48 hours..complete as per HP. PWD. specifications including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 1200x1500 mm size 12 mm thick green chalk board (non megnetic) with siperior quality framing specially anodized aluminium profile 20x15 mm with corners of black surface shall be non porous ceramic particles on the green surface for smooth writing with chalk over 11 mm thick particle board which shall have backing materials of galvanized sheet of 0.28 mm thick apprximately. the board shall be fixed on the wall with the help of nylon sleevs and screws and as per site requirement..complete as per HP. PWD. specifications including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Supplying,filling,spreading and levelling stones boulders of size rang 5 cm to 20 cm(five centimeter to twenty centimeter)in recharge pit,in required thickness, complete complete iincluding carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing stone slab with Table rubbed,edges rounded and polished, of size 75x50 cm (seventy into fifty centimeter) deep and 1.80 cm (one poit eight centimeter) thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 (one cement isto two coarse sand isto four graded stone aggregate 6 mm (six milimeter) nominal size complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge:-.

Providing and fixing trap of self cleaning design with screwed down or hinged grating with or without vent arm complete. including the cost of cutting and making good the wall and floors etc,100 mm inlet and 100 mm outlet. sand cast iron S & S as per IS:3989 complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 ltr. (ten litre) low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS:7231 with all fittings and fixture complete. including carriage of material up to all leads and lifts and as per the direction of Engineer-in-Charge. WC pan with ISI marked White solid plastic seat with lid

Providing and fixing wash basin with C.I. brackets 15 mm CP brass pillar taps, 32 nmm CP brass waste of standared pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

White vitreous china flat back wash basin of cera no 1025 size 550x400 mm with single 15 mm CP brass pillar tap.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm( five hindred eighty into three hundred eighty into three hundred fifty milimeters) with white PVC outomatic flushing cistern,with fittings,standard size CP brass flush pipe, spreadrs with unions and clamps. (all in CP brass) with waste fittings as per IS:2556, CI trap with out let grating and other couplings in CP brass, including painting of fittings and cutting and making good the walls anfd floors wherever required: single half stall urinal with 5 litre PVC automatic flushing cistern etc.complet. as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing white vitreous china laboratory sink size of 600x450x200 mm (Six hundred into four hundred fifty into two hundred ) with C.I. Bracket C.P brass chain with rubber plug,40 mm (forty milimeter) CP brass Waste and 40 mm (forty milimeter) CP brass trap with necessary CP brass union complete including painting of fittings and brackets cutting making good the wall wherever required.complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing CP brass bottle trap (heavy duty) ISI marked IS: 8931 and 8934 for wash basin or sink. 32 mm (thirty two miolimeter) dia. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing 100 mm dia sand cast iron grating for gully / floor trap complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing 600mm x 450mm ( six hundred milimetre into for hundred fifty milimetre ) bevelled edge mirrior of superior glass (of approved quality) complete with 6mm (six milimeter ) thick hard board ground fixed to wooden cleats with C.P.brass screws and washers complete as per HP.PWD., specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing PTMT CP brass towel rail (heavy duty) ISI marked IS 8931 and 8934 complete with brackets fixed to wooden cleats with C.P. brass screws with concealed fittings arranjments of approved quality and colour complete (i) 600 mm (six hundred long) towel rail with total length of 645 mm (six hundred forty five milimeter) width 78 mm (seventy eight milimeter) and effective height of 88 mm (eighty eight milimeter) weighing not less than 190 (one hundred ninety) grams complete as per HP,PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 600mm x 120 mm x 5mm (six hundred into one hundred twenty into five milimeter) glass shelf with EDGES ROUD OFF, SUPPORTED ON ANIDISED ALUMINIUM ANGLE FRAME with C.P. Brass bracket and guard rail complete, fixed to 40 mm (forty milimeter) long screws. rawl plugs etc complete. as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 8 mm (eight milimeter) dia CP/SS jet with flexible tube upto 1.00 (one meter) long with SS triangular plate to European type WC of quality and make as approved by engineer in charge. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing CP brass toilet paper holders including complete. as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing polytheline-Aluminium polythylene (PE-AL-PE) composite pressure pipe confirming to IS-15450 U.V. stabilized with carbon black having thermal stability for hot and cold water supply capable to with stand temrature upto 80 degree centigrate,including all special fittings of composite materials (engineering plastic blend and brass inserts wherever required) e.g. elbows,tees,reducers, couplers and connections etc.with clamp at 1.00 m (one metre) this includes testing of joints complete. including carriage of materials upto all leads and lifts as per the direction of the Engineer-in-Charge. (a) Internal work-Exposed on wall.

1620 ( 20mm twenty milimetre O.D. pipe).internal fittings

(ii) 2025 ( 25 mm O.D. pipe).internal fittings

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc. for external work ,complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.25mm (tweny five milimeter) diameter nominal bore

Making connection of GI distribution branch with GI main of following sizes by providing and fixing tee,including cutting and threading the pipe etc. complete. 25mm to 40mm (tweny five into forty milimeter) nominal bore complete and aincluding carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Fixing water metre and stop cock in GI pipe line including cutting and threading the pipe and making long secrews etc. complete. (cost of water meter and stop cock to be paid for separately) including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge..

Construction of masonry chamber 600mm x 600mm x 750mm ( six hundred milimetre into six hundred milimetre into seven hundred fifty milimetre ) inside, in brick work in cement mortar 1:4 (one cement isto four coarse sand) for sluice valve, with CI surface box 100 mm (one hundred milimeter) top diameter, 160 mm (one hundred sixty milimeter) bottom diameter, and 180 mm (one hundred eighty milimeter) deep (inside) with chained lid and RCC top slab 1:2:4 ( one cement isto two coarse sand isto four graded crushed stone aggregate 20mm nominal size ), including necessary excavation, foundation concrete 1:5:10 ( one cement isto five coarse sand isto ten graded stone aggregate 40 mm (forty milimeter) nominal size and inside plastering with cement mortar 1:3 ( One cement isto three coarse sand) 12 mm (twelve milimeter) thick,finished with a floating coat of neat cement complete as per standard design. with common burent clay F.P.S. (non modular) bricks of class designation 7.50.complete and )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing and placing on terrace (at all floor levels) polythy lene water storage tank of I.SI ; 12701 marked, with cover and suitable locking arrangment and making necessary holes for Inlet and outlet and over flow pipe but with out fittings and the base support for tank . including carriage of material with in all leads and lifts. and as per the direction of Engineer in charge.and as per the direction of Engineer in charge (i) 7000 lters capacity.

Supplying and fixing C.I. cover 300 mm X 300 mm (three hundred milimeter into three hundred milimeter) without frame for gully trap (standard pattern) the weight of the cover to be not less than 4.50 kg (four point five kilograme) complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Supplying and fixing C.I. cover without frame for main holes. 455x610 mm (four hundred fifty five into six hundred ten milimeter) rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing PTMT angle stop cock 15 mm (fifteen milimeter ) nominal bore,weighing not less than 85 (eighty five) grams .complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing unplasticised PVC connection pipe with brass unions: 45 cm (forty five centimeter) and 15 mm (fifteen milimeter) nominal bore. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing CP brass long nose bib cock of approved quality confirming to IS: standard and weighing not less than 810 (eight hundred ten) grams. 15 mm (fifteen milimeter) nominal bore complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 20 mm (twenty milimeter) nominal bore gun metal gate valve with C.I. wheel of approved quality(screwed end) etc. complete. as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing 25 mm (twenty five milimeter) nominal bore gun metal gate valve with C.I. wheel of approved quality(screwed end) etc. complete. as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing G.I. or M.I. Union 32 mm (thirty two milimeter) nominal bore,complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Constructing brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarsed sand ) with RCC top slab with 1:1.5:3 mix (one cement isto one point five coarse sand isto three graded stone aggregate 20 mm (twenty milimeter) nominal size), foundation concrete 1:4:8 mix (one cement isto four course sand isto eight graded stone aggregate 40 mm (forty milimeter) nominal size) , in side plastering 12 mm thick (twelve milimeter) with cement mortar 1:3 (one cement isto three coarse sand) finished with floating coart of neat cement and making channels in cement concrete 1:2:4 ( one cement isto two coarse sand isto four graded stone aggregate 20 mm (twenty milimeter) nominal size, finished with a floating coat of neat cement complete as per standard design, complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

in side size 90x80 (ninety into eightycentimeter) and 45 cm (forty five centimeter) deep including CI cover with frame (light duty) 455x610 mm (four hundred fifty five into sixhundred ten milimeter) internal dimensions,total weight of cover and frame to be not less than 38 kg (thirty eight kilogramme) (weight of cover 23 kg (twenty three kilogramme) and weight of frame 15 kg (fifteen kilogramme)

with common brunt clay F.P.S. (Non modular) bricks of class designation 7.50

Providing and fixing PVC waste and ventilating pipes including filling the joints with approved adhesive .complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge. (i) 75 mm diameter pipe

Providing and fixing PVC waste and ventilating pipes including filling the joints with approved adhesive .complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge. (i) 110 mm diameter pipe. GF to IST floor & 2nd floor

Providing and fixing PVC waste and ventilating pipes including filling the joints with approved adhesive .complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge. (i) 150 mm diameter pipe.

Providing and fixing mild steel holder bat clamps of ISI marked of approved design to cast iron or sand cast iron pipes embedded in and including cenment concrete block 10x10x10 cm (ten into ten into ten centimeter of 1:2:4 mix (one cement isto twocoarse sand isto four graded hard stone aggregate 20 mm (twenty milimeter) nominal size etc. complete. as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge. (i) 75 mm diameter

Providing and fixing mild steel holder bat clamps of ISI marked of approved design to cast iron or sand cast iron pipes embedded in and including cenment concrete block 10x10x10 cm (ten into ten into ten centimeter of 1:2:4 mix (one cement isto twocoarse sand isto four graded hard stone aggregate 20 mm (twenty milimeter) nominal size etc. complete. as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge. (i) 110 mm diameter

Providing and fixing mild steel holder bat clamps of ISI marked of approved design to cast iron or sand cast iron pipes embedded in and including cenment concrete block 10x10x10 cm (ten into ten into ten centimeter of 1:2:4 mix (one cement isto twocoarse sand isto four graded hard stone aggregate 20 mm (twenty milimeter) nominal size etc. complete. as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge. (i) 150 mm diameter

Providing and fixing PVC fittings and acessories ISI marked complete and as per HP. PWD. Specifications of 1990 vplume-I including carriage of materials, labour, tool and plant through all modes of transportation

PVC door bends of required degree (any radious) with oval access door insertion rubber washer 3 mm (three milimeter) thick, bolts and nuts complete supreme fittings and accessoris complete

75 mm diameter

110 mm diameter

150 mm diameter

Plain bends

75 mm diameter

110 mm diameter

150 mm diameter

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge .

75 mm diameter

110 mm diameter

150 mm diameter

Providing and fixing PVC plain double equal branch ISI marked with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

75 mm diameter

110 mm diameter

150 mm diameter

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

75 mm diameter

110 mm diameter

150 mm diameter

Providing and fixing soil, waste and vent pipes : 100 mm dia sand cast iron S & S pipe as per IS:1729 complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing PVC, waste and ventilating pipes including filling the joints with approved adhesive complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.(i) 110 mm diameter