Providing Generator arrangements in the newly constructed Marriage Hall

Amount

200 KVA DG SET Supply, Erection, Testing, Commissioning and Handing over of 1No 200 KVA Diesel Generator set of 0.8 P.F. Three Phase 415/420 Volts, 50 C/S, 1500 RPM CPCB IV+ Norms and BIS specification Approved capacity compressing of Engine BHP/ suitable BHP of water cooled clock wise rotating feed pump with 100KW/200KVA operating capacity brush less alternator close coupled underneath fuel tank standard, safeties, LLOP with stop solenoid, battery with lead, Electric start and vibration fitting & accessories and AMF control panel as detailed below including transporting of unloading changes.

(A). ENGINE Water cooled diesel engine suitable for Generator application with a shaft output suitable at 1500 RPM under NTP conditions. The Engine shall comprise the following standard fitting flexible coupling, fly wheel air cleaner ,fan blower, radiator, water pump, fuel pump, fuel filter lubricating oil filter etc., (B) 12/24 Volt Electronic starting Equipment Complete with starter motor, dynamo, standard batteries with cable, flexible exhaust piping of 50 cms length ( C ) ENGINE INSTRUMENT PANEL / MOUNTED Starting push button/ staring key, lubricating oil temperature gauge, lubricating oil pressure gauge, water temperature gauge, safety control for low lubricating oil pressure, safety control for high water temperature, safety control for over speed, hour meter (mechanical) and RPM indicator, battery charging ammeter. The engine should be capable of providing 10% over load for one hour for every 11 hours continuous at full load. (D). Alternator 200 KVA/160 KW capacity of brush less alternator AC, Three phase 50 c/s, 415/420V,0.8PF, 1500 RPM under NTP conditions conforming to IS 13364 (Part – II) 1992 to be means of coupling

(26) 1No Mains Voltage monitor (27) Hooter/Audio Alarm for indicating set fails to start and for DG O/L (28) 1 Set Timers (29) Audio and visual indication arrangements for a. Low lubricating Oil pressure b. High water temperature c. Over speed (30) 1No Earth fault relay (31) Isolator to Isolate the neutral Note: 1. The control panel should be complete with necessary fuses, cables, labels, other accessories with neutral isolation arrangements. 2 . The engine should trip for the following a. Low lubricating Oil pressure b. High water temperature c. Over speed (F). FUEL TANK : Fuel tank of 350 liters capacity and with inlet and outlet connections level indicator with scale etc., (G).BASE FRAME :

(G).BASE FRAME : The Base frame should be fabricated MS channel frame of rigidly welded construction for mounting of generator set. The engine and alternator should be coupled by suitably designed diaphragm type flexible coupling with guard and mounted on the base frame with proper alignment. The supply of generator set includes loading. (H). ACOUSTIC ENCLOSURE The Acoustic enclosure be free standing floor mounting type with modular construction with the provision to assemble and dismantle easily and designed to suit all weather conditions. Erection of Acoustic enclosure suitable for 250 KVA Diesel generator complete with all accessories as above with required concreting and suitable supports etc., (i) Supply of manuals for operation & maintenance of DG set with warranty card etc.,

Supply and Run of 12 core 2.5 sqmm armoured copper control cable FRLS in suitable PVC rigid pipe on wall/Ground/ ceiling with connection (For AMF to 250KVA Genset)

Supply and installation of exhaust piping of sufficient length with suitable MS clamps so as to extend outside the generator room with necessary thermal insulation

Construction of RCC foundation of suitable for 200KVA Gen set weight approximately weight 5000 kg with cement concert 1:2:4 with sand cushion all around the foundation for the erection of 125 KVA & 250 KVA DG set with proper alignment

Provision for Diesel for testing and first running of 200 KVA DG set

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth Connection

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps/supports on wall/floor/ground for earth connection

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps/supports on wall/floor/ground for earth connection

Preparation of Electrical schematic diagram, site plans, physical layout 5 copies and payment of CEIG fees submission of completion report, rectification report, obtaining drawing approval, safety certification etc., for 200 KVA DG Set

Supply and Installation of 315 A Automatic Transfer switch in sheet steel enclosure on suitable Angle iron frame arrangements on wall with cable adaptor boxes with earth connection.

Sub total

S J INFRA (BID ID -1405102)