Construction of various buildings of Ravenshaw University (Mahanadi Campus), Cuttack, Odisha

Sl. No. Description of Item Schedule Amount Total Amount

Sl. No. Description of Item Schedule Amount Total Amount

Academic Building

Academic Building

Recreation Hall

Digitally signed by VARUN

Abstract Estimate :CONSTRUCTION OF ACADEMIC BLOCK PHASE-I AT RAVENSHAW UNIVERSITY MAHANADI CAMPUS,CUTTACK,ODISHA.

*Rates including taxes

Abs. Non-Schedule Non-Schedule

Head Description of Item Unit Qnty. Schedule Rate Schedule Amount

Sr. Rate Amount

Civil Works 0.00 0.00

Earth work in excavation of foundation trenches in ordinary soil

including dressing of sides and levelling the bed up to the required

depth and depositing the excavated materials away from the work

1 site within 50m initial lead & 1.5m initial lifts with sundries & T&P

required for the work complete including cost of all labour,labour

cess,T&P,sundries etc. as directed by the Engineer in charge.

Filling available excavated earth (excluding rock) in trenches, plinth,

sides of foundations etc., in layers not exceeding 20 cm in depth,

consolidating each deposited layers by ramming and watering, lead

up to 50 m and lift up to 1.5 m.

Supplying and filling in foundation and plinth with good quality river

sand including watering, ramming with cost, conveyances, royalties

3 of all materials and cost of all labour with T&P required for the work 0.00

etc. complete as per specification & direction of Engineer-in-charge

Providing & applying of pre constructional anti-termite treatment by

drilling 12mm dia holes at distance of 30cm @ junction of wall &

floor about 300mm apart deep enough to reach the soil below &

chemical emulsion (IMIDACHLOPRIED 30.5SC mixed with 47.5ltr

4 water) pumped these holes to soak the soil @ 1 ltr solution of each Sqm 1941.00 177.00 0.00 343,557.00

hole as per manufactures specification & the holes should be pluged

the filling materials including cost of all materials,

labour,conveyance, T&P , all taxes and hire charges of machinaries

as per direction of Engineer-in-charge.

Boring, providing and installation bored cast-in-situ reinforced

cement concrete piles of grade M-25 of specified diameter and

length below the pile cap, to carry a safe working load not less than

specified, excluding the cost of steel reinforcement but including the

cost of boring with bentonite solution and temporary casing of

appropriate length for setting out and

1 5 removal of same and the length of the pile to be embedded in the 0.00

pile cap etc. by percussion drilling using Direct mud circulation

(DMC) or Bailer and chisel technique by tripod and mechanical

Winch Machine all complete, including removal of excavated earth

with all its lifts and leads (length of pile for payment shall be

measured up to bottom of pile cap).

Cement concrete of proportion (1:3:6) in foundation and floors

using 4cm size clean hard black crusher broken granite stone metal

of approved quality and from approved quarry including hoisting,

lowering and laying concrete in layers not exceeding 15 cm. (6")

3 6 thick to the required level ramming, watering, curing etc. complete Cum 250.00 7672.83 1,918,208.00 0.00

including cost, conveyance, royalties of all materials with all labour

and T&P required for the work etc. complete in all respect and as

per the direction of the Engineer-in-charge.

Plain cement concrete (1:2:4) using 12mm size black hard crusher

broken granite chips of approved quality from approved quarry

including hoisting, lowering and laying concrete in layers, watering,

4 7 curing etc. complete including cost, conveyance, royalties of all Cum 25.20 9589.39 241,652.58 0.00

materials with labour,labour cess and T&P etc. required for the work

complete as per the direction of the Engineer-in-charge.

Fly Ash brick masonry in cement mortar (1:6) in foundation & plinth

using Fly Ash bricks of 23 x 11 x 8 cm size having a crushing

strength of not less than 75 kg./sqcm with dimensional tolerance ±

2% including splays cutting circular moulding chamfering and

corbelling and similar such type of works with all necessary

projections watering and curing after immersing the bricks in water

at least for six hours before use including cost, conveyance, and

royalties of all materials with all labour,labour cess and T & P

required for the work complete in all respect as per direction of

Engineer-in-Charge

Fly Ash. brick masonry of size 23 cm. x 11 cm. x 8 cm. having

crushing strength not less than 75 kg. Per Sqr. Cm. in cement

mortar of mix (1:6) with approved grade cement and screened &

washed sand for mortar after immersing the bricks for 6 (Six) hours

in water before use in Superstructure including splays cutting,

6 9 circular moulding, corbelling, chamfering and similar such type of 0.00 0.00

works, watering and curing etc. including cost, conveyance, loading,

unloading, royalties and taxes of all materials, cost of all labour,

scaffolding, sundries, T&P required for the works etc. complete in all

respect as directed by the Engineer-in-charge.

Fly Ash brick masonry in cement mortar (1:4) in super structure

using Fly Ash bricks of 23 x 11 x 8 cm size having a crushing

strength of not less than 75 kg./sqcm with dimensional tolerance ±

2% including splays cutting circular moulding chamfering and

corbelling and similar such type of works with all necessary

projections watering and curing after immersing the bricks in water

at least for six hours before use including cost, conveyance,

royalties and taxes of all materials with all labour,labour cess and T

& P required for the work complete in all respect as per direction of

Engineer-in-Charge.

Digitally signed by VARUN

Providing, lifting, hoisting and laying Reinforced cement concrete of

M-25 grade as per approved designs and drawings having a

minimum compressive strength (in work test) 250 Kg. / Square cm.

in 15 cm. cubes at 28 days after mixing and test conducted in

accordance with I.S. 516 using 12 mm. to 20 mm. size black hard

crushed broken granite stone chips and screened and washed sharp

sand for mortar of approved quality from approved quarry, washed

and cleaned ( 20mm. size chips not to exceeds 25 % ) to be mixed

in concrete mixture with Portland slag cement (PSC) including

hoisting, lowering, laying and compaction concrete by using

15 11 vibrators, watering and curing for 28 days, centering and shuttering 0.00 0.00

then after dismantling and removing debris from the work site and

finishing the exposed surface smooth providing grooves or beads

wherever necessary including cost, conveyance, loading, unloading,

royalties and taxes of all materials and cost of all labours, sundries,

T & P required of the work etc. complete in all respect as directed by

the Engineer-in-Charge. But excluding cost and conveyance of M.S.

rods or Tor steel and binding wires and labour charges for

straightening, cutting, bending etc. of M.S. rods or tor steel tying

the grills and placing in proper position.

16 11.1 Ground Floor 0.00 0.00

20 11.5 d) Column up to ceiling level Cum 101.06 19613.02 1,982,091.40 0.00

26 11.11 a) Column up to ceiling level Cum 81.50 22031.31 1,795,551.60 0.00

32 11.17 a) Column up to ceiling level Cum 69.76 24926.20 1,738,951.56 0.00

37 11.22 Terrace floor 0.00 0.00

38 11.23 a) Column up to ceiling level Cum 36.58 28391.51 1,038,561.36 0.00

Supplying Cutting, straightening coiled or bent up M.S. Rod or tor

steel of primary steel producers including bending, binding, welding

and jointing if necessary and tying the grills and placing in position

as required for R.C.C. Work and for providing fan hooks as required,

hoisting, lowering, laying including cost, conveyances of M.S. Rod or

42 12 tor steel and binding wires of 18 to 20 gauge and labour required for 0.00 0.00

the work for bending, binding and tying the grills in all floors with

labour cess etc. (payment will be made on standard weight of B.I.S.

for M.S. Rods or tor steel only) etc. complete as per specification &

direction of Engineer-in-charge.

Providing 12 mm thick cement plaster with cement mortar of mix

(1:6) with screened and washed sharp sand for mortar and finished

smooth to the rough surface of walls in all heights after racking out

joints including watering and curing, rounding of corners, providing

47 13 grooves where ever necessary with cost, conveyance, royalties of 0.00 0.00

all materials with cost of all labour,labour cess, T&P, and scaffolding

required for the work etc. complete in all respect as directed by the

Engineer in charge.

Providing 16 mm thick cement plaster with cement mortar of mix

(1:6) with screened and washed sharp sand for mortar and finished

smooth to the rough surface of walls in all heights after racking out

joints including watering and curing, rounding of corners, providing

52 14 grooves where ever necessary with cost, conveyance, royalties of all 0.00 0.00

materials with cost of all labour,labour cess, T&P, and scaffolding

required for the work etc. complete in all respect as directed by the

Engineer in charge.

Providing 6 mm thick cement plaster with cement mortar of mix

(1:4) with screened and washed sharp sand for mortar and finished

smooth to R.C.C. work after closed deep chipping & slurry treatment

including watering and curing, rounding of corners, providing

57 15 grooves where ever necessary with cost, conveyance, royalties of 0.00 0.00

all materials with cost of all labour,labour cess, T&P, and scaffolding

required for the work etc. complete in all respect as directed by the

Engineer in charge.

Digitally signed by VARUN

Fixing granite tiles of approved dimension area above 0.4 sqm

(20mm thick) in floor, treads of steps and landing on 20mm thick

bed of cement mortar (1:4) jointed with neat cement slurry mixed

62 16 with pigment to match the shades of the tiles including rubbing and 0.00 0.00

polishing etc. complete with cost, conveyance, royalties and taxes of

all materials complete in all respects as per direction of Engineer-in-

Fixing granite tiles of approved dimension area above 0.1 up to 0.4

sqm (10mm thick) in Dados, treads of steps and landing on 12mm

thick cement mortar (1:3) jointed with neat cement slurry mixed

66 17 with pigment to match the shades of the tiles including rubbing and 0.00 0.00

polishing etc. complete with cost, conveyance, royalties and taxes of

all materials complete in all respects as per direction of Engineer-in-

Supplying, fitting & fixing of 8-10 mm thick & size of 600x600 mm

Glazed vertified floor tile (GVT) of with veilcraft (VC/FT ) shield(

Scratch free/stain free) with water absorption limit between 0.08%

to 3% and conforming to IS : 15622:2006 (Group B Ib). laid on 20

70 18 mm thick cement mortar (1:4) (1 cement : 4 course sand) and 0.00 0.00

filling joints with white cement of approved quality including cost of

all materials, labour T&P etc. required for the work all complete as

per direction of the Engineer-in-charge (for New Work only )

Supplying, fitting & fixing of 8-10 mm thick and size of

600x600 mm Glazed vertified wall tile of in dadoes,

skirting and risers of steps of laid on 12 mm thick cement

74 19 mortar (1:3) (1 cement : 3 course sand) jointed with slurry 0.00 0.00

mixed with pigment to match the shades of the tiles etc.

complete including cost of all materials, labour T&P etc.

required for the work all complete as per direction of the

Engineer-in-charge.

Supplying, fitting and fixing of Antiskid Ceramic Floor Tiles in

flooring using special plain / printed series Ceramic Floor Tile of

premium grade ( having minimum thickness 7 mm to 8 mm & size

300 mm x300 mm, confirming to I.S 13755 of approved quality and

shade in floors, treads on steps and landings on 20 m.m thick bed

of cement mortar of mix (1:4) laid in proper slope and gradient with

screened & washed sharp river sand for mortar and fixing with

neat white cement slurry,grouting the joints with neat white

cement slurry mixed with required quantities of pigments (Tiles are

to be immersed in the water for required time before use) of

approved make to match the shades of the Ceramic Floor Tiles if

required including cost, conveyance, loading, unloading, stacking,

royalties , all taxes, cost of all Labour, Labour cess ,Sundries, T&P

required for the work , Watering , Curing for required days ,

cleaning the flooring space manually etc.complete in all respect as

directed by the Engineer-in-charge.

Supplying, fitting & fixing of 600mm x 300mm Ceramic wall tiles

having thickness 6.5mm to 7.0 mm confirming to IS 13753 in

dadoes, skirting and risers of steps laid on 12 mm thick cement

82 22 mortar (1:3) (1 cement : 3 course sand) jointed with slurry mixed 0.00 0.00

with pigment to match the shades of the tiles etc. complete

including cost of all materials, labour T&P etc. required for the work

all complete as per direction of the Engineer-in-charge

Providing & Fixinng factory made 100% Solid WPC ( Wood Polymer

Composite ) - Door Frame 125 mm x 65 mm Single Rebated, made

from Wood Polymer Composite ( Single Extruded Process ) material

comparising of virgin PVC polymer of K Value 57-60 ( Suspension

Grade ), Calcium Carbonate and Natural Fibers ( Wood Powder/ Rice

Husk/ Wheat Husk ) and Non toxic additives fabricated with meter

Joints after applying PVC solvent Cement & screwed with full body

treaded star headed screws having minimum frame density of 780

kg/ cbm & an ISO 9001 - 2015 Certified Company, having good

screw holding capacity ( Screw Withdrawal strength of ( Min. 990 N

), Minimum Compressive Strength of 58 N/mm2, Modulus of

elasticity 900N/mm2 and resistance to spread of flame of class A

category with property of being termite / borer proof , water /

Moisture Proof & Fire retardant & Fixed in position with SS Dash

Fasteners / Hold Fast of reuired dia and lenght, , all as per

specifications drawings as directed by the Engineer-In-Charge.

Material test certificate and authentication should be compulsory

provided by the manufacturing company.

Supplying, fitting and fixing of 32mm thick flush door shutter with

approved quality of 30mm thick BWR block board pasted with 1mm

90 24 thick sunmica on both side of approved design and quality including 0.00

cost of all door S.S fittings and fixtures etc. complete in all respect

as per the direction of the Engineer-in-Charge.

Digitally signed by VARUN

Factory made single leaf rigid FRP(alternately called GRP) sandwich

composite door shutter of 32mm thick laminated with two GRP skins

with wood grain finish fabricated using UV-stabilised Isopthalic

Gelcoat and one layer of 450 gsm E-glass Chopped Strand Mat

(CSM) impregnated with orthopthalic palyester resin. The thickness

of the skins shall not be less than 3.00mm Expanded

Polystyrone(EPS) structural foam panel of 29mm thickness and a

density of 20kg/cu.mtr shall be used as core material. Wooden

reinforcements made of seasoned sal wood block of cross section

not less than 28mmx32mm and also necessary sal wood

reinforcements for fitting the metal fittings such as tower bolts,

aldrops, handles etc shall be provided. A structural adhesive

compatible with (EPS) foam shall be used for bending the core

material, the sal wood reiforcements and the skins. The material

and process for manufacturing the door shutters shall conform to RV-

TIFAC composites Design Centre's standards and specifications and

the door shutters tested in conformation to IS: 4020-1998. The

finish of door shutter will be plain colour white/ Ivory/ Beige/ Light

grey/ Mahogany/ Teak wood or any other colour using high quality

pigments. Three heavy whight mild steel butt hinges type-I(ISI

marked) size 100mm are to be fitted on one side of shutter with FRP

frame of size 45x90mm.

Providing and fixing ISI Marked un-insulated fire rated door

confirming to IS 3614:2021,& tested to IS17518,and shall carry a

unique label with certification/test report number.The fire rating

shall be for 120minutes integrity only.Material shall be galvanised

steel conforming to IS 277, made out of minimum 1.2(18 SWG) for

both frame and shutter, G.I. sheet (zinc coating 120

gsm/sqm).Frame shall be 125 x 55 grooved profile with built in

rebate for fire rated smoke seal. Frame shall be mitered and field

assembled. EPDM smoke seal to be provided along with frame as

98 26 standard. Door shutter shall be double skin of 46mm thick with 0.00

required fire rating and with vision panel. The infill material shall be

resin bonded honeycomb core. All doorset shall be factory prepped

for receiving appropriate hardware and provided with necessary

reinforcement for hinges, locks and door closers.The door stiles

should be interlocked, for pairs of doors integral astragals has to be

provided on the meeting stile for both active and inactive leaf.

Vision lite, minimum 5mm clear fire rated glass of size 150 x

750mm (max 0.12sq.mt) on both shutters, fixing with clipon

All frame and door shutter shall be finished polyster powder coated

to minimum 50microns, of approved colour as per the direction of

the engineer incharge. Cost of double leaf doorset shall include

following hardware and accessories as a complete assembly. SS ball

bearing hinges of SS-304 grade of size100x75x3mm,1no Fire rated

mortise dead lock, 55mm BS, 20mm sq. forend, including

escutheion, sss as per EN 12209 with both side key cylinder on

active leaf and 2nos flush bolt on the inactive leaf in case of double

leaf door along with dust proof socket at bottom, 1pairs Pull handle

D type, 22dia, CTC 300mm, back to back per leaf, with spindle,SS

304, SS finish. 1no of Door closer with spring size of EN 2- 4, as per

EN1154 and CE marked per leaf. Suitable anchor fastners for fixing

on different type of wall construction as per manufacturer

recommendation.Once frames is installed it shall be filled with fire

rated PUF. Manufacturer test certificates shall covers complete door

set as a un-latched assembly with a valid test certificate not

exceeding 5 years from the date of issue of report. for more info

refer doors details drawings, including cost of all materials, all

labour, sundries, T&P etc. complete in all respect as per direction of

Engineer-in-Charge.

Supplying and fixing of Powder coated 50-60 microns approved

colour of Aluminium 40mm Casement series Door Unit with suitable

aluminium extrude profiles. the system is designed to accommodate

12mm clear toughened glass of . the rate quoted inclusive of

hardwares like antilift,roller, Espag lock cum handle,epdm gaskets,T

mullion ,Fly Mullion ,bottom adopter ,mid transom ,glazing clip for

12 mm glass felt along with all accessories etc complete. the gap

between the wall and window will be filled with silicon weather

sealant in the outer side. Casement Door Outer frame - 40mm x

45.3mm Series x 1.4mm thickness, Fly mullion - 44 x 60 mm x

1.4mm thickness, T Mullion 40 x 78.4mm x 1.4mm thickness,

Transom - 40.28 x 125.8 x 1.75 mm thickness, Bottom adopter -

34.6 x 26 x 1.5mm thickness, including cost of all materials, all

labour, sundries, T&P etc. complete in all respect as per direction of

Engineer-in-Charge.

Supplying and installing UPVC- 3 track 3 shutter sliding windows

with Outer dimension - 104 x 49 sash dimension of 61mm x 39mm

for windows with corners fusion welded, fully reinforced with

Galvanized steel of 1.2 mm to 2 mm. The sash will be fitted with

5mm reflective toughened glass . The windows must be installed

105 29 complete with all kinds of ironmongery (including EPDM 0.00

gaskets,bridging wedges and glass packers) and with suitable water

draining system. Application of Silicon sealant from Inside / Outside

of Dowcorning / GE or equivalent including cost of all materials, all

labour, sundries, T&P etc. complete in all respect as per approved

drawing & direction of Engineer-in-Charge.

Digitally signed by VARUN

Supplying, fitting & fixing in all floors of M.S. grills, grill gates, M.S.

gates, garage door, collapsible gates with top and bottom rails, steel

windows, critical frames for windows, stair case and parapet railing

made out of M.S Square bar/ flat including stair case hand railing

110 30 with 40mm. dia G.I.pipe etc. including painting two coats over a 0.00

coat of redoxide primer as per approved drawing and design with

cost of all materials & labour, labour cess, T&P, sundries etc.

complete in all respect as per specification & direction of the

Engineer-in-Charge.

Priming one coat with wall cement primer (water bound) to make an

even finished surface in all floors and heights to wall surface of

approved make and shade including sand papering, applying putty

115 31 wherever necessary & cost of scaffolding, staging charges with cost,

conveyance, cost of all labour,labour cess T&P etc. complete as per

the direction of the Engineer-in-charge.

Finishing wall with textured exterior paint of required shade :

120 32 New work (two or more coats appplied @3.28litre/10sqm)over 0.00

and including priming coat of exterior primer applied

Finishing plastered surfaces of walls with cement based wall putty

(Water based) of approved make duly approved by Engineer-in-

Charge) and finishing the surface smooth and even by sand

125 33 papering to receive painting in walls, at all heights with staging

wherever necessary with cost, conveyance, cost of all

labour,labourcess, all T&P etc. required for the work complete in all

respect as per the direction of the Engineer-in-charge.

Painting two coats with plastic emulsion paint with a approved

quality primer to make an even finished surface in all floors and

heights to wall surface of approved make and shade including sand

papering, applying putty wherever necessary & cost of scaffolding,

130 34 staging charges with cost, conveyance, cost of all labour,labour

cess, T&P etc. complete as per the direction of the Engineer-in-

Engineer-in-charge.

Painting two coat with approved synthetic enamel paint to new

wood work over a coat of Red oxide primer including cost,

conveyances, royalties, taxes of all materials and cost of all labour

135 35 with T&P required for the work etc. complete as per specification &

direction of Engineer in charge.

Painting two coat with approved synthetic enamel paint to new iron

work over a coat of Red oxide primer including cost, conveyances,

139 36 royalties, taxes of all materials and cost of all labour with T&P

required for the work etc. complete as per specification & direction

of Engineer in charge.

Supplying, fitting and fixing of Stainless steel of 304 grade in hand

railing using 50mm dia of 2mm thick circular pipe with Balustrade of

size 32mm x 32mm x 2mm @ 0.90mtr. C/C and stainless square

144 37 pipe bracing of size 32mm x 32mm x 2mm in 3 rows in stair case as

per approved design and specification, buffing, polishing etc with

cost, conveyance, cost of all labour,labour cess, T&P etc. required

for the work complete in all respect as per direction of the Engineer-

Providing 2.5cm thick Grading Concrete over roof slab with cement

concrete (1:2:2) using 6mm size black hard granite crusher broken

chips and screened & washed sharp sand for mortar and finished

148 38 smooth to the rough surface of slab including watering and curing

with cost, conveyance, royalties of all materials with cost of all

labour, labour cess and T&P required for the work etc. complete in

all respect as directed by the Engineer in charge.

Digitally signed by VARUN

Waterproofing application:- Providing and application of two

component polymer modified flexible cementitious waterproofing

coating at a thickness of 1.5 -2.5 mm The membrane should have

Elongation equal or more than: 30%

Crack Bridging ability : Up to 1 mm

150 39 Adhesive strength: 1.0 N/mm² @ 28d 0.00

Tensile elongation: 60% @ 20°C

Shore A Hardness >85 (between 3 - 7 days)

etc. as per direction of E.I.C (For longer span, in terrace panel of

4m*4m should be done by groove cutting, and filling with PU

Supply of all materials & laying the waterproofing material of torch

shield P3160(3mm)with its primer 2 coats or equivalent water

proofing material after drying cleaning the concrete surface over the

152 40 concrete floor/roof/ balcony/sunken and dado upto 1'6" in wall

including cleaning,applying and mending as per specification

including cost,conveyance,taxes,royalities of all materials to work

site etc.all complete as per the direction of the Engineer-in-charge.

Providing & Installation of GFRC GFRC JALI (Glass Fiber Reinforced

Concrete) thickness of 25-30 mm & Border thickness of 50 mm with

Pattern, design, and colour of approved make to be fixed

on/between RCC /Block work Column or structural work with Dry

Fixing method with appropriate SS Pipe & Cleats frame work, using

156 41 fasteners, and necessary hardware etc. The element shall be made 0.00

from '53 grade' Portland Cement , Quartz, Fine Silica Sand, Alkali

Resistant Glass fibre , Super plasticizers / Additives , Polymers and

U.V resistant Synthetic inorganic pigments shall be used for

pigmentation .The material casting shall take place in Synthetic

Rubber / FRP Mould

Supply and Installation of System comprises of Semi unitized

extruded aluminum Structural Glazing wall panels comprising of

extruded Vertical Aluminium mullions and Horizontal transoms with

super Durable Powder Coating finish of minimum 60 Microns

confirming standards to withstand wind pressure. The mullions and

transoms are installed on locations as indicated in the architectural

drawings. The framing members provide no structural support for

the building and the Structural Glazing wall is deemed to be a

lightweight façade which is intended to separate the external from

the internal of the building and provides natural light into the

building. The curtain wall system is designed to have internal

drainage system within the extruded sections with 6MM Blue

160 42 toughened glass. Gaskets are employed as water barrier between

the aluminum gridwork and the glazed sashframe, which are fully

drained in the event of leakage past the primary seal. The external

grooves are covered with application of backer rod with weather

sealant of approved make as indicated in the concept drawing.

Fabricating and supplying Mild Steel ( HDG coated ) Brackets to

accommodate 3 Dimensional movement for achieving perfect

verticality and proper fixing of structural glazing system with the

RCC/ masonry/structural steel framework of building structure,

using stainless steel (chemical/mechanical) anchor fasteners/ bolts,

Teflon separator to prevent bimetallic contacts with nuts and

washers etc. of stainless steel Grade 316, of the required capacity

and in required numbers

Supply and Installation of 14 mm GRG Tiles steppe edge ceiling tile

of size 595 x 595 x 14 mm on the edge & 7 mm in the center having

all edges encapsulated with chemical treated paint & having

densified tegular edge ,weight 5 kg/m2 having random circular semi

perforated in dual diameter / Random fissure semi perforated in

variable length which is suspended by using 0.3 mm thick and 15

mm wide pre coated metal T 15 grid system. The technical

parameters are as follows : Core - GRG Silicate, Fire – Class 1 & P ,

Acoustics – NRC 0.5,Climate (degree C, RH) – 50, 99, STC - 30,

Termite resistance ,Light reflectance – 85 %,Green (RC %) – 25,

Hygiene (VoC, Clean room) – Low, , Load capacity (Kg) - Antisag.

The T 15 Grid system of 600 x 600 mm module shall include wall

angle(WA 15) with unequal flanges of size 14 x 20 x 3000 mm wide,

length 3000 mm, 0.43 mm thick fixed along the perimeter of wall

164 43 with the help of nylon sleeves and suitable fasteners at 300 mm 0.00 0.00

centers. Then suspend the Main T15 (MT15 W36) having flange

width 15 mm /24 mm , height 32/38 mm and length 3600 mm

thickness 0.30 mm from the soffit with help of soffit cleat and wire

at 1200 mm c/c. Cross T15 (CT15 W12) with flange width 15 mm,

height 32 mm and length 1200 mm is then interlocked into the pre-

cut slots in the Main T15 at 600 mm centers in the direction

perpendicular to the Main T15. Finally, Cross T15 (CT15 W06)

having flange width 15 mm, height 32 mm and length 600 mm are

then interlocked into the pre cut slots in the 1200 mm Cross T15 at

1200 mm centers and in direction parallel to the Main T15. GRG Tile

of size 595 x 595 x 14 mm thick shall be placed into the grid size of

600 x 600 mm. Ensure arrow marks behind panels are oriented in

one direction to achieve uniform shade. Test certificate will be

submitted after procurement of materials

Digitally signed by VARUN

Vertical load testing of piles in accordance with IS 2911 (Part

IV)including installation of loading platform by Kentledge/Anchor

piles method and preparation of pile head or construction of test cap

168 44 and dismantling of test cap after test etc. complete as per

specification & the direction of Engineer in-charge.(Lab test should

be carried out of any Govt lab /NABL accreditation lab)

169 44.1 Single pile upto 128 tonne Safe capacity

170 45 Initial test (Test Load 2.5 times the Safe capacity) Each pile 1.00 668639.18 668,639.18

Lateral load testing of single pile in accordance with IS:2911 part-IV

for determining safe allowable lateral load on pile.

172 Sub-Total of Civil Works TOTAL 129,756,164.56 12,801,862.96

173 Plumbing Works

174 INTERNAL PH WORK

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having theRmtal stability for hot & cold water supply, including all

CPVC pipes SDR-11 as per IS-15778/2007 plain & brass threaded

175 1 fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This 0.00 0.00

includes jointing of pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and making good the same

including testing of joints complete as per direction of Engineer in

Concealed work, including cutting chases and making good the walls

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having theRmtal stability for hot & cold water supply, including all

CPVC pipes SDR-11 as per IS-15778/2007 plain & brass threaded

186 2 fittings, including fixing the pipe with clamps at 1.00 m spacing. This 0.00 0.00

includes jointing of pipes & fittings with one step CPVC solvent

cement and testing of joints complete as per direction of Engineer in

187 2.1 External work 0.00 0.00

Providing all materials, labour, T&P for fitting & fixing of following

brass full way Valves in all floor & fixing with the pipes after cutting

the pipes to required shape & size including wastage etc. of

189 3 following nominal diameter, all complete including testing the joints 0.00 0.00

with required water pressure.The cost inclusive of transportation

scaffolding etc. all complete as per specification excluding GST and

direction of Engineer-in-charge.

190 3.1 25mm dia brass full way valve Nos 12 1430.40 17,164.75 0.00

191 3.2 32mm dia brass full way valve Nos 6 2094.03 12,564.17 0.00

192 3.3 50mm dia brass full way valve Nos 15 3935.18 59,027.73 0.00

Providing all materials labour, T&P for making grooves in Mtr. 178

bricks/stone masonary walls vertically or horizontally up to required

depth and width in all floor for laying of pipes and fittings up to

50mm dia, testing the joints with required water pressure and

193 4 making good the damages with cement concrete 1:2:4 with 12mm 260.54 46,376.83 0.00

size h.g.c.b.chips and finished smooth with cement morter (1:4) to

original shape including cost of materials, curing, conveyance, taxes

of all materials etc. all complete as per specification & direction of

Providing all labour,T&P for cutting holes in bricks or stone masonry

wall for taking pipes in all floors and making good the damages

194 5 with cement concrete 1:2:4 finished smooth with CP 1:4 to original 0.00 0.00

shape including cost of all materials, curing, conveyance, taxes,

duties etc. all complete as per specification & direction of Engineer-

For 25mm to 110mm dia pipe to pass in 250mm thick wall No. 123

Providing all labour,T&P and cutting holes in brick masonry wall No. 111

/RCC wall for crossing of GI pipes / CI pipes/ HCI pipes of different

dia and making good to the damage with (1:4) complete as per

specification & direction of EIC.

Providing, fixing, jointing and testing PP mineral filled low noise

level Soil & Waste piping system as per BS EN 1451, SN4-S16, with

minimum density for pipes and fittings 1.4 gm/cm3. Pipes and

fittings made from Polypropylene-M (mineral reinforced) and

available from 50 – 160 mm with push fit SBR type rubber ring

sockets for easy installation. Pipes should have 3 layer design.

Should have hot water resistance up 95ºC for short term loading

(90ºC for long term loading). Piping system should have chemical

resistance of pH 2-12. Fittings should have swept design from 75-

160mm and depth gauge for proper fittings against thermal

expansion and contraction, should have top marking at every 15°

intervals in angular rotation for better alignment. Piping system

includes all required fittings & accessories such as coupler, bend,

tee, Y, reducer, access pipe, multi floor traps, Nahni trap with

extension piece etc. for conveying soil, waste & rainwater purpose in

floors, ceiling suspended, or on walls, with leak proof joints etc.

Setting the pipe in 1:2:4 CC in case of concealed plumbing, wall

chasing, holes, supporting, clamping, covering back with chicken

mesh & plaster and making the wall good as per approved shop

drawing. Testing as per tender specifications/EIC.

Digitally signed by VARUN

Supplying all materials, labour, T&P and fitting and fixing U-PVC

SWR soil waste ventilating pipes and fittings of the following outside

diameter conforming to ISI No 13592/1992 to walls with nails,

bobbins and wooden plugs or laying in trenches including jointing

200 8 with supply of approved rubber lubricant by non-heat application 0.00

method/as per manufacturer's specification, testing, earthwork in

excavation in all kinds of soil and refilling of trenches , cost &

conveyance of all materials to worksite, payment of taxes etc. all

complete as per P.H specification and direction of the Engineer-in-

204 8.4 110mm U-PVC offset without ear Each 30 480.73 14,421.96 0.00

Providing all materials, labour, T&P European type floor mounted NOS 37

211 9 WC with seat, white plastic lid and flushing PVC cistern as per 13293.290 491,851.73 0.00

specification of Hindware Popular (Starwhite),

Supplying, installing, testing and commissioning of approved make White

Viterous urinals 3.8 LPM urinal with Urinal valve Autoclosing system

212 10 with Built-in control cock & wall flange. Urinal size-355X340X535 MM Each 26.00 8437.94 219,386.54 0.00

confirming to IS 2556: Part 6 -1996 etc all complete as per

specifications.

Supply all materials and labour for fitting and fixing of following size

Half Pedestral Wash Basin with fixing Accessories,Size-550X400

mm, of approved make in all floor of approved quality including

213 11 cutting the walls & floor and making good the damages with cement 0.00 0.00

concrete etc. including all taxes, duties, transportation etc. all

complete as per direction of EIC.

Under Counter Wash Hand Basin.

(Size-605X415X200 mm )

Wall Hung Half pedestral wash hand basin

Supply,fitting and fixing all materials, labour, T&P as per

specification , the following Brass/ CP / G.M. fittings at appropriate

216 12 locations to thr pipe lines at all floors and at all heights, of approved 0.00 0.00

make confirming to relevent IS specification . etc complete in all

Brisk Health Faucet ABS with Rubbit cleaning system,1.25 m Long

217 12.1 SS Flexible Tube & ABS Wall Hook . NOS 37.00 1501.94 55,571.69 0.00

218 12.2 Two-way Bibcock with wall Flange. 37.00 1964.94 72,702.63 0.00

219 12.3 One-way Bib cock with wall Flange. 0.00 2330.76 0.00 0.00

221 12.5 15mm dia Angle Stop cock with Wall Flange. NOS 189.00 1,468.86 277,615.30 0.00

222 12.6 15mm dia Concealed stop cock with wall flange. NOS 26.00 863.17 22,442.42 0.00

Supplying all materials, labour, T&P and fixing mirror of superior

glass mounted on 6mm.thick A.C. sheet or ply wood sheet and fixed 0.00 0.00

to wooden plugs with CP screws and washers complete as per

specification and direction of Engineer in charge.

225 13.2 Soap dish in each toilet . NOS 37.00 1,015.15 37,560.70 0.00

32 mm C.P. Bottle Trap 32mm with 125 & 175mm Long Wall

Connection pipe & wall Flange No. 1,862.39

Waste Coupling of Waste coupling 32mm Size Full Thread with

80mm height or equivalent. No. 645.58

228 13.5 15mm CP Extension piece 126.00 7,820.57 0.00

229 13.6 110 mm dia CP Nahani trap with Grating 71.00 389.40 27,647.40 0.00

Supplying all materials, labour, T&P and providing fitting and fixing

(Aqua guard) Pure Chill 120 PSS UV (Eureka Forbes)of size

750x570x1350mm height with water storage capacity 120 liters

230 14 along with 3 nos of faucets 2 for cold water and 1 for normal water Nos 2.00 154,893.88 309,787.76 0.00

including a flow of 1.5 ltr per minute etc all complete as per

approved drawing,specification and direction of the Engineer in

Providing & fixing Ductile Iron Pipes Pressure ,socket and spigot

pipes conforming to IS : 8329 :2000 (Complete With all joints & 0.00

Fittings) with DI pipes of K-7 Class.

232 15.1 100 mm Ductile iron Class K-7 pipes meter 185.00 1210.98 224,030.38 0.00

Supplying all materials, labour, T&P and fitting and fixing of Cast

Iron Sluice Valve with double flanged ends for water

works purposes conforming to IS 14846 - 2000 (Standard) etc all

complete as per the direction of Engineer-in-charge.

Cast Iron Reflux Valves (Non-return valves) with double NOS 2

flanged ends conforming to IS : 5312 (Part-I) - 2004

236 SINTEX TANK FOR OVER HEAD 0.00 0.00

Fixing double layer cylinderical water storage tanks conforming to

IS: 12701--1996 including cutting holes through the tank and fixing

mild steel tubes and fittings and providing extra sockets and jam

237 18 nuts, fixing ball valve etc, including hoisting upto a height and 0.00 0.00

placing the tank to the required position etc all complete as per

specification and direction of the engineer in charge.

238 18.1 DOMESTIC WATER TANK 2000 LIT. PVC TANK EACH 7 54387.94 380,715.56 0.00

239 18.2 FIRE WATER TANK 5000 LIT. PVC TANK EACH 2 123130.84 246,261.69 0.00

240 Ball Float (Mechanical) 0.00 0.00

Digitally signed by VARUN

Supply, Installation & commissioning of reputed make mechanically Nos 5

operated ball float with Brass Arm for each tank for closing &

opening the inlet of each tank as per the water level in each tank

suitable for handling 10 Bar pressure

242 Sub-Total of Plumbing Works TOTAL 3,924,179.91 0.00

243 Electrical Works 0.00

244 Sub-Head I (modular Wiring Items)

Recessed wirring to light point/ fan point/ exhaust fan point/ call

bell point with 1.5 sq.mm FRLS PVC insulated copper conductor of

ISI marked Mak with 20 mm dia HMS FRLS PVC conduit ISI

marked ) and ceiling rose ISI marked of modular type G.I box with

metallic cover plate (both side) ( flame retradant type) - of

suitable size, modular box with 1.5 sq. Mm FRLS PVC insulated

245 1 single core multistandard copper conductor as earth wire including 0.00 0.00

all accessories and connection as per direction of Engineer -in -

Charge. . All the switches & sockets should be warrantied for a

replacement period of 2 years against defects with ncessary test

report & Warrnaty certificate to be submitted to the department for

genuinity of product & to avail free after sales service within

warranty period for acceptance of materials.

Supplying ,fixing of 6A Plug on the same board in existing switch

board with complete fitting by 01 no of 6A switch & socket (modular

type)( ( flame retradant type)) & other required accessories of ISI

marked as approved as per direction of Engg. -in -Charge.

249 2 .(Maximum 02 nos point in one circuit).All the switches & sockets Nos 60 231.28 13,876.80 0.00

should be warrantied for a replacement period of 2 years against

defects with ncessary test report & Warrnaty certificate to be

submitted to the department for genuinity of product & to avail free

aftersales service within warranty period for acceptance of materials.

Supplying,fixing of 6A Plug on the separate board with complete

fitting by 01 no of 6A switch & socket(modular type)( ( flame

retradant type)) with suitable size modular box & cover( falme

retradant type) including supplying of all required accessories of

ISI marked as approved as per direction of engg-in-charge..

250 3 .(Maximum 02 nos point in one circuit).All the switches & sockets Nos 80 650.18 52,014.40 0.00

should be warrantied for a period of 2 years against manufacturing

defects against which ncessary test report & Warrnaty certificate to

be submitted to the department for genuinity of product & to avail

free aftersales service within warranty period for acceptance of

Supplying,fixing of 1x16A Plug on the separate board with

complete fitting by 01 no of 16A switch & socket(modular type)((

flame retradant type)) with suitable size modular box & cover(

flame retradant type) including supplying of all required accessories

of ISI marked as approved as per direction of engg-in-charge..

251 4 (For equipement power)All the switches & sockets should be Nos 38 810.66 30,805.08 0.00

warrantied for a replacement period of 2 years against defects with

ncessary test report & Warrnaty certificate to be submitted to the

department for genuinity of product & to avail free aftersales service

within warranty period for acceptance of materials.

Supplying,fixing of 1x6A+1X1 6A Plug on the separate board with

complete fitting by 01 no of 16A+1 no 6A switch & socket(modular

type) ( ( flame retradant type) with suitable size modular box &

metallic cover plate (both side)( falme retradant type)including

supplying of all required accessories of ISI marked as approved as

252 5 per direction of engg-in-charge.. (For equipement power)(Maximum Nos 22 1,526.92 33,592.24 0.00

02 nos point in one circuit).All the switches & sockets should be

warrantied for a replacement period of 2 years against defects with

ncessary test report & Warrnaty certificate to be submitted to the

department for genuinity of product & to avail free aftersales service

within warranty period for acceptance of materials.

Supplying,fixing of 3x6A+1X1 6A Plug on the separate board with

complete fitting by 01 no of 16A+3 nos 6A switch &

socket(modular type) ( (flame retradant type) with suitable size

modular box & metallic cover plate (both side)(anti bactorial &

falme retradant type)including supplying of all required accessories

of ISI marked as approved as per direction of engg-in-charge. (For

253 6 equipement power). (Maximum 02 nos point in one circuit).All the Nos 10 2,351.74 23,517.40 0.00

switches & sockets should be warrantied for a replacement period of

2 years against defects with ncessary test report & Warrnaty

certificate to be submitted to the department for genuinity of

product & to avail free after sales service within warranty period for

acceptance of materials.

Receass wiring for circuit/submain wiring with the following

mentioned size PVC FRLS insulated, copper conductor, single core

cable in recessed HMS FRLS PVC conduit of mentioned size

as required as per direction of Engg.-in-Charge.

254 7 2 nos single core 1.5 sq. mm copper wire for phase and neutral and Mtr 1227.5 187.62 230,303.55 0.00

01 no of single core 1.5 sq. mm copper wire for earth continuty

conductor. In 20 mm dia non metallic heavy duty conduit (LDB to

LSB/LIGHT CKT)(2X1.5+1X1.5)

Receass wiring for circuit/submain wiring with the following

mentioned size PVC FRLS insulated, copper conductor, single core

cable I in recessed HMS FRLS PVC conduit of mentioned size

as required as per direction of Engg.-in-Charge.

2 nos single core 2.5 sq. mm copper wire for phase and neutral and

255 8 01 no of single core 1.5 sq. mm copper wire for earth continuty Mtr 2838.5 204.14 579,451.39 0.00

conductor in 20 mm dia non metallic heavy duty conduit.(BDB to

LSB/LIGHT CKT/5A PLUG/UPS POINT ) (2X2.5+1X1.5)

Digitally signed by VARUN

Receass wiring for circuit/submain wiring with the following

mentioned size PVC FRLS insulated, copper conductor, single core

cable in recessed HMS FRLS PVC conduit of mentioned size

as required as per direction of Engg.-in-Charge.

2 nos single core 4 sq. mm copper wire for phase and neutral and

01 no of single core 1.5 sq. mm copper wire for earth continuty

conductor in 20 mm dia non metallic heavy duty conduit .(PDB to

PSB/ POWER POINT/AC POINT) (2X4+1X1.5)

Receass wiring for circuit/submain wiring with the following

mentioned size PVC FRLS insulated, copper conductor, single core

cable in recessed HMS FRLS PVC conduit of mentioned size

as required as per direction of Engg.-in-Charge.

257 10 2 nos single core 6 sq. mm copper wire for phase and neutral and Mtr 616.5 261.96 161,498.34 0.00

01 no of single core 2.5 sq. mm copper wire for earth continuty

conductor in 25 mm dia non metallic heavy duty conduit .(LFDB TO

LBDB/UBDB) (2X6+1X2.5)

Receass wiring for circuit/submain wiring with the following

mentioned size PVC FRLS insulated, copper conductor, single core

cable in recessed HMS FRLS PVC conduit of mentioned size

as required as per direction of Engg.-in-Charge.

258 11 4 nos single core 6 sq. mm copper wire for phase and neutral and Mtr 616.5 376.42 232,062.93 0.00

02 nos of single core 4 sq. mm copper wire for earth continuty

conductor in 32 mm dia non metallic heavy duty conduit.(LFDB TO

LBDB/Medical equipement) (4X6+2X4)

Receass wiring for circuit/submain wiring with the following

mentioned size PVC FRLS insulated, copper conductor, single core

cable in recessed HMS FRLS PVC conduit of mentioned size as

required as per direction of Engg.-in-Charge.

4 nos single core 10 sq. mm copper wire for phase and neutral

259 12 and 02 nos of single core 6 sq. mm copper wire for earth continuty Mtr 616.5 526.28 324,451.62 0.00

conductorin 32 mm dia non metallic heavy duty conduit .(LFDB TO

FLOOR PANEL TO TPN BDB power) (4X10+2X6)

Supplying and installation of 25A AC starter Modular type, coil

voltage-230 Volt A.C. on mod Box of suitable size including modular

coveras required as per direction of Engg.-in-Charge .All the

Components should be warrantied for a replacement period of 2

260 13 years against defects with ncessary test report & Warrnaty Nos 23 739.86 0.00 17,016.78

certificate to be submitted to the department for genuinity of

product & to avail free aftersales service within warranty period for

acceptance of materials.

Supply and fixing CALL bell (Ding dong type) /Buzzer on the

existing switch box/cover. .as required as per direction of Engg.-in-

Charge.All the Components should be warrantied for a replacement

period of 2 years against defects with ncessary test report &

261 14 Warrnaty certificate to be submitted to the department for genuinity mtrs 6 252.52 1,515.12 0.00

of product & to avail free aftersales service within warranty period

for acceptance of materials.

S/F of Bakelite angle holder/batten holder reputed make A

catagory ISI marked as approved )of ISI marked conforming to IS-

1258/1987 in place of ceiling rose as per direction of Engg.-in-

262 15 Charge .All the Components should be warrantied for a replacement each 11 89.68 986.48 0.00

period of 2 years against defects with ncessary test report &

Warrnaty certificate to be submitted to the department for genuinity

of product & to avail free aftersales service within warranty period

for acceptance of materials.

263 Sub-Head II (Light fitting Fixture & Fan) 0.00

Supplying, installation, of exhaust fan of heavy duty 300 mm sweep

1400 rpm with louvers of exhaust fan in the existing wall, including

fixing & conntection as required as per direction of Engg.-in-Charge.

Replacement Warranty will be 2 years.

Supplying, installation, of exhaust fan of heavy duty 380 mm sweep

1400 rpm with louvers of exhaust fan in the existing wall, including

fixing & conntection .as required as per direction of Engg.-in-

Charge. Replacement Warranty will be 2 years.

Supplying, installation, testing and commssioning of 1200 mm

sweep white/milky colour BLDC ceiling fan with aluminium blades

having wattage not more than 28W and air delivery ≥215m3/min

266 18 including wiring the down rod of standard length (upto 30 cm) with Nos 208 4,394.32 0.00 914,018.56

1.5 sq mm PVC insulated, copper conductor, single core cable etc.

as required as per direction of Engg.-in-Charge,Replacement

Warranty will be 4 years.(With fan Regulator)

Supplying and fixing of Energy efficient Recess /Surface

mounted square/round shaped LED luminaire made up of CRCA

powder coated sheet steel of 25W and system lumens output not

less than 3250 lumens (130 lm/ wt) with diffusers for better light

transmission and pure effect with High luminous flux LEDs for better

light output, CRI not less than 80, CCT of 5700-6500 degree K, THD

267 19 less than 10%,internal surge protection of 3 KV, complete with Nos 100 3,164.19 0.00 316,419.36

Non integrated isolated electronic driver (protects the output

/secondary side from any disturbance on the input / primary side

ensuring safe operation)and all other accessories suitable for

operation on140- 270 V, 50 Hz ,L70 @50,000 burning hrs (2 years

warranty)supply .as required as per direction of Engg.-in-Charges

. The luminaire must be Replacement Warranty will be 2 years.

Digitally signed by VARUN

Supplying and fixing of Energy efficient surface /recess

mounted square /round shape 18 W LED luminaire of dimension of

consists of white powder coated , die-cast Alluminium housing

with high quality frosted diffuser for glare-free uniform lighting

distribution with wattage not more than 18 watt and lumen output

268 20 of 1800 lumens, , CRI not less than 80,CCT of 6000 degree K,THD Nos 400 1,817.20 0.00 726,880.00

less than 10%, with electronic driver, internal surge protection of 3

KV , L70 B50: 50000 hrs and all other accessories suitable for

operation on 220 V to 240 V supply as required as per direction of

Engg.-in-Charge. .The luminaire should be Replacement Warranty

will be 2 years

SITC of energy efficient LED tube light fittings with decorative

alluminium batten and LED tube light having power rating not more

than 20 watt and lumen output not less than 2200 lumen complete

269 21 with electronic driver and all other accessories with diffuser having Nos 416 856.68 0.00 356,378.88

2 years warranty i/c connection etc as required as per direction of

Engg.-in-Charge. . The luminaire should be Replacement Warranty

will be 2 years .

SITC of Sleek LED 10 watt mirror light fitting with extruded

polycarbonate housing,High optically efficient diffuser,above wash

basin complete with all accessoriesetc. directly on wall, including

270 22 connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, Nos 16 868.48 0.00 13,895.68

single core cable and earthing etc. as required as per direction of

Engg.-in-Charge.

The luminaire should be Replacement Warranty will be 2 years

S/F of 5 step type Modular electronic Fan Regulator ISI Marked

271 23 with all connection complete in all respect as per direction of Sets 208 441.32 0.00 91,794.56

Engineer in charge

Supplying and fixing extra conduit down rod of 20 cm length G.I.

pipe 15 mm dia, heavy gauge including painting etc. as requiredas

272 24 required as per direction of Engg.-in-Charge . 450 38.94 17,523.00 0.00

(Note : More than 5 cm length shall be rounded to the nearest 10

cm and 5 cm or less shall be ignored)of ISI mark as approved. Nos

273 BDBS,DB,AC DB,FLOOR PANELS,MCBS 0.00 0.00

Supplying and fixing of following mentioned way, three pole/single

pole and neutral, sheet steel,double door MCB distribution board,

415 volts/240 volts shall be as per IEC 61439-3,integrated door

earthing system offering additional safety to the user,High quality

polyurethane Gasket,the box and cover shall be fabricated to

withstand IK09,the DB should be properly pre-treated with 7 tank

274 25 process and duly powder coated, phosphatized with powder coated 0.00 0.00

finish, on surface/recess, complete with terminal blocks,with

suitable size FR PVC insulated copper conducter up to terminal

blocks, tinned copper busbar, neutral busbar, earth bar, din bar..

The Distribution boards should be Replacement Warranty will be 3

4 Way(8+12) Way TPN MCB DD DB Horizontal Type as per IEC

61439-3 suitable for Flush mounting and Surface mounting with

275 25.1 100A Copper Bus Bar for each phase, with neutral Bus bar, Earth Nos 9 5,038.60 0.00 45,347.40

Bar & Cable ties for cable management, prefitted masking sheet,

IP43-IK09 with metal door Warranty on DB is 3 years

Supply and fixing of 12 way DD single pole and neutral sheet steel

MCB distribution board 250V on surface/recess complete with tinned

copper bus bar, neutral bus bar, earth bar, din bar, detachable

gland plate, interconnections, phosphatized and powder painted

including earthing etc. as required (but with out MCB/ RCCB/

Isolator) Warranty on DB is 3 years

2+4 way MCB Enclosure DB (GLAZED door)(only each EM.

CONNECTION UPS LOAD)Warranty on DB is 3 years

8 Way(8+24) Way TPN MCB DD DB Horizontal Type suitable for

Flush mounting and Surface mounting with 100A Copper Bus Bar for

each phase, with neutral Bus bar, Earth Bar & Cable ties for cable

management, prefitted masking sheet, IP43-IK09 with metal

door(FOR LIGHT,POWER INDOOR,3-PH,POWER

LOAD)Warranty on DB is 3 years

Supplying and fixing 20 amps rating, 240 volts, C series,10KA

breaking capacity, Double poles MCB of Acti 9/ABB SB 200 in

the existing MCB DB complete with connections as per direction of

Engg.-in-Charge. .Warranty on MCB is 3 years.

Supplying and fixing 6 amps to 32 amps rating, 240 volts, C

series,10KA breaking capacity, single poles MCB of Acti 9/ABB

SB 200. the existing MCB DB complete with connections as per

direction of Engg.-in-Charge. .Warranty on MCB is 3 years.

Supplying and fixing 40 Amps rating, C series,10KA breaking

capacity,4P, 415 volts, MCB . -- Acti 9/ABB SB 200 in the existing

281 27.5 MCB DB complete with connections, testing and commissioning etc. Nos 9.00 3499.88 0.00 31,498.92

as required as per direction of Engg.-in-Charge. .. The MCB should

be Replacement Warranty will be 3 years..

Supplying and fixing 40 Amps rating,C series,10KA breaking

capacity, 4P, 415 volts, RCCB 30mA . - Acti 9/ABB FB 200 in the

282 28.5 existing MCB DB complete with connections, testing and Nos 9.00 6182.02 0.00 55,638.18

commissioning etc. as required as per direction of Engg.-in-Charge.

. The MCB should be Replacement Warranty will be 3 years.

Supplying and fixing 25Amps rating,C series,10KA breaking

capacity, DP 240 volts, MCB Acti 9/ABB SB 200 in the existing

283 29.5 MCB DB in the existing MCB DB complete with connections as per Nos 6.00 1136.34 0.00 6,818.04

direction of Engg.-in-Charge. The MCB should be Replacement

Warranty will be 3 years.

Supplying and fixing 40Amps rating,C series,10KA breaking

capacity, DP 240 volts, MCB Acti 9/ABB SB 200 in the existing MCB

284 30.5 DB in the existing MCB DB complete with connections as per Nos 12.00 1799.50 0.00 21,594.00

direction of Engg.-in-Charge. The MCB should be Replacement

Warranty will be 3 years.

Digitally signed by VARUN

Supplying and fixing 63Amps rating,C series,10KA breaking capacity

,DP 240 volts, MCB Acti 9 /ABB SB 200 in the existing MCB DB in

285 31.5 the existing MCB DB complete with connections as per direction of Nos 12.00 1799.50 0.00 21,594.00

Engg.-in-Charge.The MCB should be Replacement Warranty will be

Supplying and fixing 63Amps rating,C series,10KA breaking

capacity, 4P 415 volts MCB Acti 9/ABB SB 200 in the existing MCB

286 32.5 DB in the existing MCB DB complete with connections as per Nos 9.00 3499.88 0.00 31,498.92

direction of Engg.-in-Charge..The MCB should be Replacement

Warranty will be 3 years.

Supplying and fixing 63Amps 4P 415 volts RCCB 30 mA -- Acti

9/ABB FB 200 in the existing MCB DB in the existing MCB DB

287 33.5 complete with connections as per direction of Engg.-in-Charge..The Nos 9.00 6182.02 0.00 55,638.18

MCB should be Replacement Warranty will be 3 years.

288 (Earthing) INSTALLATION 0.00 0.00

Supplying,installation,testing & commissioning of materials and

installation of GI earth plate 600mmx600mmx6mm thick ISI marked

with G. I. nut bolts & washers including cost of burnt wood

289 34 charcoal, salt, foreign soil, water pouring arrangements, brick Nos 4.00 7670.00 30,680.00 0.00

masonary enclosure on top with removable RCC cover complete with

labour for excavation of pit in all kinds of soil & rock as required and

as per direction of Engineer-in-charge.

Providing and fixing 25mm x 5 mm GI strip on surface or in recess

290 35 for connections etc. as required as per direction of Engg.-in-Charge. Mtr 178.00 177.00 31,506.00 0.00

Providing and fixing 50mm x 6 mm GI strip on surface or in recess

291 36 for connections etc. as required as per direction of Engg.-in-Charge. Mtr 56.00 377.60 21,145.60 0.00

CABLING AND END TERMINATION MAIN AREA

Supplying of one number PVC insulated armoured and PVC sheathed

XLPE property AL. conductor power cable of 1.1 KV grade of 0.00 0.00

following size cables as per direction of Engg.-in-Charge.

294 37.1 3.5core x 240 sq mm (2 run from TRF to Main LT Panel) Mtr 166.00 2678.60 444,647.60 0.00

Supplying of one number PVC insulated armoured and PVC sheathed

XLPE property AL. conductor power cable of 1.1 KV grade of 0.00 0.00

following size cables as per direction of Engg.-in-Charge.

298 38.2 4core x 16 sq mm (BDB LIGHT /POWER,EQUIPEMENT ) Mtr 25 273.76 6,844.00 0.00

299 38.3 4 core x 6 sq mm (for small power) Mtr 33 245.44 8,099.52 0.00

3.5core x 35 sq mm (To FDB LIGHT / power BDB/UPS

PANEL,separate panel for OT Complex,MCU) Mtr 25

3.5core x 50 sq mm (From main panel to light floor distribution

panel) Mtr 33

302 LAYING OF CABLE 0.00 0.00

Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv

grade size not exceeding 25 SQ. MM direct in ground in the trench

303 39 in one horizental formation including excavation ,sand coushing 3,149.42 0.00

protection covering and refilling the trench etc as required as per

direction of Engg.-in -charge. Mtr 17 185.26

Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv

grade size exceeding 25 SQ. MM but not exceeding 120 SQ. MM

304 40 direct in ground in the trench in one horizental formation including 28,145.36 0.00

excavation ,sand coushing protection covering and refilling the

trench etc as required as per direction of Engg.-in -charge.

Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv

grade size exceeding 120 SQ. MM but not exceeding 400 SQ. MM

305 41 direct in ground in the trench in one horizental formation including 18,408.00 0.00

excavation ,sand coushing protection covering and refilling the

trench etc as required as per direction of Engg.-in -charge.

Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv

306 42 grade size not exceeding 25 SQ. MM direct in ground in the 1,210.68 0.00

EXISTING PIPE etc as required as per direction of Engg.-in -charge. Mtr 18 67.26

Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv

grade size exceeding 25 SQ. MM but not exceeding 400 SQ. MM

307 43 direct in ground in the EXISTING PIPE etc as required as per 1,677.96 0.00

direction of Engg.-in -charge.

Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv

308 44 grade size not exceeding 25 SQ. MM in open duct etc as required as 3,039.68 0.00

per direction of Engg.-in -charge. Mtr 56 54.28

Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv

grade size exceeding 25 SQ. MM in open duct 400 SQ. MM direct in 2,378.88 0.00

ground in the EXISTING PIPE etc as required as per direction of

Engg.-in -charge. Mtr 32 74.34

Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv

grade size not exceeding 25 SQ. MM in surface with shaddle and 2,106.30 0.00

screw etc as required as per direction of Engg.-in -charge.

Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv

grade size not exceeding 120 SQ. MM From 25 SQ. MM in surface

with shaddle and screw etc as required as per direction of Engg.-in -

Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv

grade size not exceeding 400 SQ. MM From 120 SQ. MM in surface

with shaddle and screw etc as required as per direction of Engg.-in -

Supplying and making end termination with double brass

313 49 compression gland and aluminium lugs for following mentioned size 0.00 0.00

cable.as per direction of Engg.-in-Charge.

Digitally signed by VARUN

Providing,fixing and laying of following dia G.I. pipe (medium class)

319 50 in ground complete with G.I fitting incl. trenching(75 mm depth)and 0.00 0.00

refilling as per direction of Engg.-in-Charge.

Providing,fixing and laying of fallowing dia HDPE pipe (medium

321 52 class) in ground complete with fitting incl. trenching(75 mm 0.00 0.00

depth)and refilling as per direction of Engg.-in-Charge.

324 53 MAIN CONTROL PANEL AT GF 0.00 0.00

In commer-1-01 number of 630A 4P Icu=100%Ics,36Ka

LSIG MCCB with micro processor based release Electrical

locking for normal & DG ABB-FORMULLA(FROM 250 KVA

In commer-2-01 number of 400A(320-400) 4P

Icu=100%Ics,36kA LSIG MCCB with micro processor based 0.00 0.00

release Electrical locking for normal & DG /ABB-FORMULLA

(DG 160 KVA INCOMMER)

In commer-2- 01 no of 400A 4P onload changeover switch

(160 KVA DG 01 NO)

Busbar-1&2 04 numbers of 800Amps copper busbar with

1.6A/SQ.MM current carring capacity. busbar duly sleeved by color 0.00 0.00

coated PVC sleeve & supported by suitable size DMC insulator. (for

Out going- 06 numbers of 100A 4P MCCB,,25Ka MCCB withTMR

329 based release with adjustable overload ,Icu=100%Ics 0.00 0.00

Out going- 6 numbers of 160A 4P Icu=100%Ics,,25Ka MCCB

330 withTMR based release with adjustable overload 0.00 0.00

Out going- 6 numbers of 32A rating,10 KA breaking capacity,C

331 series, 4P MCB 0.00 0.00

Out going- 6 numbers of 63A rating,10 KA breaking capacity,C

Out going- 1 number of 320A 4P Icu=100%Ics,,25Ka MCCB

withTMR based release with adjustable overload

Out going- 1 number of 250A 4P Icu=100%Ics, ,25Ka MCCB

withTMR based release with adjustable overload

Instrument- (i) 06 numbers phase indicating lamp with toggle

switch & HRC fuse.

(ii) 02 set of digital type multifunction meter with CT for

336 voltage,current,frequency,PF,THD indication with RS 485 0.00 0.00

COMPACTIVITY FOR bms data.

1 no. 4P 40kA/POLE type 2+1 SPD with 63A rating,10KA breaking

capacity ,4P MCB(TYPE-I)

S/I/T&Commissioning of LT indoor floor mounted cubical type

electrical main panel (for both light and power circuit) made out by

2mm CRCA steel sheet duly derusted & painted by simens grey

powder cote paint is designed as G.A drawing. (FOR ALL MAIN

CONNECTED LOAD) BUILDING LIGHT)as per direction of Engg.-

339 54 in-Charge. Warrentee period of replacement of panel & 0.00 0.00

accessories must be 3 years & compelete test certificate

must be submitted along with panel board including

component list.Type 2 SPD 40ka shall be installed in the

incomer. 20X10MM Separate Aluminium Earth bus bar

should be installed.

In commer- 01 no 100A 4P MCCB 16kA,C series with

on/off trip indication Light load for each floor.

Busbar- 04 numbers of 200Amps 25*5mm copper bus bar

341 Electrolytic copper busbar duly sleeved by color coded PVC sleeve & 0.00 0.00

supported by suitable size DMC insulator.

Out going- 06 nos 40-63A 4P MCB 10kA,C series Light load to

LDBs . cti 9 /ABB SB 200

Instrument- (i) 03 numbers phase indicating lamp with toggle

switch & HRC fuse.

344 (ii) 01 set of 0-100Amps Ammeter 0.00 0.00

345 (iii) 01 set of 0-500 voltmeter . 0.00 0.00

FDB RAW POWER AT 1F,2F ALONG WITH DOCTORS ROOM

S/I/T&Commissioning of LT indoor floor mounted cubical type

electrical main panel (for both light and power circuit) made out by

2mm CRCA steel sheet duly derusted & painted by simens grey

powder cote paint is designed as G.A drawing. (FOR ALL MAIN

CONNECTED LOAD) BUILDING POWER/AC)as per direction of

347 54.1 Engg.-in-Charge. Warrentee period of replacement of panel & Set 2 121,695.76 0.00 243,391.52

accessories must be 3 years & compelete test certificate

must be submitted along with panel board including

component list. Type 2 SPD 40kA shall be installed in the

incomer. 20X10MM Separate Aluminium Earth bus bar

should be installed.

In commer - 01 no 160A 4P MCCB 25kA, with ROM & S.

Link. with shunt trip.

Busbar- 04 numbers of 250Amps, Electrolytic copper busbar duly

349 sleeved by color coded PVC sleeve & supported by suitable size DMC 0.00 0.00

350 Out going- 06 nos 63A 4P MCB 10kA,C series for power BDB. 0.00 0.00

Instrument- (i) 03 numbers phase indicating lamp with toggle

switch & HRC fuse.

352 (ii) 01 set of MFM with CTS. 0.00 0.00

353 UPS PANEL FOR EMERGENCY (FOR EACH FLOOR) 0.00 0.00

S/I/T&Commissioning of LT indoor floor mounted cubical type

electrical main panel (for both light and power circuit) made out by

2mm CRCA steel sheet duly derusted & painted by simens grey

powder cote paint is designed as G.A drawing. (FOR ALL MAIN

354 55 CONNECTED LOAD) BUILDING EMERGENCY LIGHT)as per Set 2 66,397.42 0.00 132,794.84

direction of Engg.-in-Charge. Warrentee period of replacement

of panel & accessories must be 3 years & compelete test

certificate must be submitted along with panel board

including component list. 20X10MM Separate Aluminium

Earth bus bar should be installed.

In commer- 01 numbers of 63 Amps 4P MCB. (Icu=100% Isc)

355 with shunt trip & axulary for BMS & mechnical inter locking 0.00 0.00

for one incommer source to other.

Digitally signed by VARUN

Busbar- 04 numbers of 100Amps Electrolytic copper busbar duly

356 sleeved by color coded PVC sleeve & supported by suitable size DMC 0.00 0.00

Out going- 04 nos 32A rating,10KA breaking capacity,C series, 2P

MCB UPS Light load for each floor.

Out going- 03 nos 32A rating,10KA breaking capacity,C series, 4P

358 MCB OT/ICU POWER/OT MACHINE OR Bed head panel. 0.00 0.00

Instrument- (i) 03 numbers phase indicating lamp with toggle

switch & HRC fuse.

(ii) 01 set of 0-100Amps Ammeter Digital type & CTS.(DIGITAL)

361 (iii) 01 set of 0-500 voltmeter Digital type.(DIGITAL) 0.00 0.00

NB- This panel should have proper earth by suitable rated

363 UPS SYSTEM(For OT, & COMMON AREA) 0.00 0.00

Supply ,installation ,testing & commissioning of 20KVA Parallel UPS

SYSTEM WITH IGBT based inverter system, true online double

conversion system, inbuilt isolation transformer & automatic phase

sicuency corrector of 3ph in put to 3 ph output,415V, with built in

BMS with battery back up up to 30 minutes with MS Rack for battery

364 56 Housing, DC cable 7 Mtr with SFU and links for installation (Battery Set 1 737,500.00 0.00 737,500.00

required: 12V, 65AH, 32 No.s) protection for fault by

OL,UV,EF,GF,OC,Ph. . Warrentee period of all accessories &

component & system must be 2 years & compelete test

certificate must be submitted along with ups including

component list & SLD.

365 CABLE TRAY /RACE WAY FOR DISTRIBUTION OF POWER 0.00 0.00

366 Description 0.00 0.00

Supplying,fixing of perforated cable trays with horizental & vertical

bends,reducers ,tees,crossover,brakets & other accessories ar

requited confirming to IS-IEC -61537 ,the cable tray shall be

367 57 galvanised for corrosion protection confirming to DIN EN 10346/ISO mtrs 117 713.90 0.00 83,526.30

1461. Size 60mm(H) x 200mm(W) of .The Load bearing capacity of

the Cable Trays should be minimum of 104.8Kg/meter at the span

of 1.5Meter as per UL specifications as required as per direction of

Engg.-in-Charge.

Supplying,fixing of perforated cable trays with horizental & vertical

bends,reducers ,tees,crossover,brakets & other accessories ar

requited confirming to IS-IEC -61537 ,the cable tray shall be

368 58 galvanised for corrosion protection confirming to DIN EN 10346/ISO mtrs 72 1,146.96 0.00 82,581.12

1461. Size 60mm(H) x 300mm(W) of .The Load bearing capacity of

the Cable Trays should be minimum of 104.8Kg/meter at the span

of 1.5Meter as per UL specifications as required as per direction of

Engg.-in-Charge.

Supplying,fixing of perforated cable trays with horizental & vertical

bends,reducers ,tees,crossover,brakets & other accessories ar

requited confirming to IS-IEC -61537 ,the cable tray shall be

369 59 galvanised for corrosion protection confirming to DIN EN 10346/ISO mtrs 50 1,687.40 0.00 84,370.00

1461. Size 60mm(H) x 400mm(W) of .The Load bearing capacity of

the Cable Trays should be minimum of 104.8Kg/meter at the span

of 1.5Meter as per UL specifications as required as per direction of

Engg.-in-Charge.

Supplying,fixing of FLOOR RACE WAY WITH JUNCTION box

GALVANIZED(GC) type AS PER EN-ISO-1461 , with internal

370 60 dimensions of size 38mm(H) x 225mm(W), of .(With all mtrs 83 2,101.58 0.00 174,431.14

accessories,bend,cover,supporter)WITH REQUIRED SIZED

JUNCTION BOX ,COVER CONNECTOR as required as per direction of

Engg.-in-Charge.

371 Subhead- 1 (Lan System) 0.00

SITC of 4 pair Cat6 23 awg U/UTP LSZH Cable in the existing

surface/ recessed steel/ PVC conduit as required: The 4 pair

Unshielded Twisted Pair cable shall be UL Listed,exceeds the

requirements of ANSI/TIA-568-C.2 and ISO/IEC 11801 Class E , 4

twisted pairs separated by internal PE Cross Separator. Full

separator. Half shall not be accepted. Rip Cord is must,Insertion

372 61 Loss of 32.8 db/100m at 250 MHz ,Cable should support operating Mtr 750 97.94 0.00 73,455.00

temperature from -20° to +70°C Cable support Conductor

Resistance ≤ 9.38 Ω/100m Max., Cable support Delay Skew: < 45

ns/100m, Operating Voltage: 72V , Impedance: 100 ± 15 Ω @100

MHz. and Propagation Delay @250 MHz : 536 ns/100m, ETL Verified

4 connector channel performance up to 700 MHz , RoHS Compliant.

SITC of Cat6 I/O with Dual Face plate: The Outlet shall meet or

exceed requirement as per ANSI/TIA 568C.2,ISO/IEC 11801, &

EN50173. The information outlet NEXT, PSNEXT, FEXT, ELFEXT,

PSELFEXT and return loss should be verified for CAT6 @ 250Mhz &

373 62 CAT6A @ 500Mhz. The information outlet connector shall be of Nos 31 1,195.34 0.00 37,055.54

gold/nickel, thickness of gold > 0.8 μm. The connectors shall be

compatible as per IEEE 802.3af standard for POE application. The

PVC material of Face plate should complie ABS /UL94-V-O certified.

SITC of Cat6 I/O with Single Face plate: The Outlet shall meet or

exceed requirement as per ANSI/TIA 568C.2,ISO/IEC 11801, &

EN50173. The information outlet NEXT, PSNEXT, FEXT, ELFEXT,

PSELFEXT and return loss should be verified for CAT6 @ 250Mhz &

374 63 CAT6A @ 500Mhz. The information outlet connector shall be of Nos 11 808.30 0.00 8,891.30

gold/nickel, thickness of gold > 0.8 μm. The connectors shall be

compatible as per IEEE 802.3af standard for POE application. The

PVC material of Face plate should complie ABS /UL94-V-O certified.

SITC of Cat 6, 24-port loaded, 1U Modular Jack Panel Should

accommodate Cat6 with Rear Cable Management and Front

removable Tooless Information outlet. Should have easy clip

375 64 management with labels and clear label covers, Made with of Dicast Nos 3 11,585.24 0.00 34,755.72

Aluminium Alloy Material and Non Corrosive with Cat6 toolless RJ45

x 24 ports with color code front panel with patch cord locking.

Digitally signed by VARUN

SITC of Cat6 UTP 24 AWG Patch Cord Patch cord: 6 UTP Patch Cords

are Factory Tested for Better Quality and Suitable for the High

Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-

568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-

376 65 Base-T and 1000-Base-T. Available In LSZH Jacket- Reduced Toxic Nos 31 403.56 0.00 12,510.36

Gasses Emitted During Combustion , RJ45, 8P8C, 2 FORK 50μ’’

Gold Plated Contacts , 100% Factory Tested , Transparent Boot

Cable Assemblies.

SITC of Cat6 UTP 24 AWG Patch Cord Patch cord: 6 UTP Patch Cords

are Factory Tested for Better Quality and Suitable for the High

Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-

568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-

377 66 Base-T and 1000-Base-T. Available In LSZH Jacket- Reduced Toxic Nos 16 480.26 0.00 7,684.16

Gasses Emitted During Combustion , RJ45, 8P8C, 2 FORK 50μ’’

Gold Plated Contacts , 100% Factory Tested , Transparent Boot

Cable Assemblies.

SITC of 6 core Single mode OS2 Unitube Armoured Optical fiber

cable through existing conduit: The Fiber should be OS2 Single

Mode Optical Fiber Cable of Size 9/125µm. Outdoor Corrugated

Steel tape Central loose tube. ( Standard Approved: ISO 11801 2nd

B1.3 / EN 60793-2-50: class B1.3 / ITU Recommendation G.652.D -

the oder ITU designations A, B and C are also fulfilled /

OS1/ISO/IEC 24702:2006, cat. OS2; also OS1 requirements are

fulfilled/IEEE 802.3 - 2002 incl. 802.3ae ) Jacket.

SITC of Rack mount Draw Type Loaded 6 port LIU available in

Standard 19” ,Dimensions (mm) : 430 X 220 X 1U , Cold Rolled

Steel as Raw Material , Consist of Top Cover and Bottom Panel ,

Easy to Assemble and Dissemble , Three Types of Input Holes Cable

379 68 Entry Through Water Proof Cable Clamp , 12 Duplex SC or LC Nos 3 9,848.28 0.00 29,544.84

Adapter Interface , Splice 24 Fibers at Most with 1 Tray ,Adaptor,

SM, Duplex SC, PC Type ,Pigtail, Support the TIA/EIA

Telecommunication Wiring Standards. Compact Design , Telcordia

SITC of OFC Patch Cor, SM (OS2), Duplex LC-SC, LC-LC PC Type,

3M, LSZH Fiber Optic Single Mode OS2 Patch Cords are offered in

380 69 LSZH Jackets with Corning Fiber,Insertion Loss : <= 0.2 db, Max Nos 3 2,481.54 0.00 7,444.62

0.3db/MTRJ: Max 0.5db Return Loss : PC>= 45db, UPC>=50db,

SITC of 10G-LX/LH SFP transceiver module,SMF, 1310nm, 9/125 um

Single mode Fiber Type up to 20 KM.

SITC of 24 Port 10/100/1000Mbps Layer 3 Switch includes 4 Gigabit

Combo ports, additional 4 x 1G/10G SFP+ ports. Default 2 Fixed AC

Power Supply. Supports OSPF v2/v3,BGP4+,VRRP , Security

Network Management CLI, WEB, Telnet, SNMPv1/v2c/v3 through

IPv4 and IPv6 , Syslog and external Syslog Server, HTTP SSL ,

382 71 SNMP MIB, SNMP TRAP , FTP/TFTP , SNTP/NTP , RMOM 1,2,3,9 , Nos 1 220,896.00 0.00 220,896.00

Authentication by Radius/TACACS SSH v1/v2 , Dual firmware

images/ Configuration files , 802.3ah OAM, 802.1ag OAMSwitching

capacity 128Gbps , Throughput 95 Mpps , MAC Address 16K

,Routing Table 13K , Layer 3 Interface Max 1K , Working

Temperature : 0°C~50°C, storage -40°C~75°C.

SITC of 9U/500D Wall Mount Rack with Accessories: The rack size

should be 600W x 500D, Front frame integrated with top, bottom,

front and two side panels for better rigidity and strength, Front

Glass Door with Lock loaded, Compliance with standards shall be UL

383 72 11 , ISO 9001:2008 including Power Distribution Unit (06/16 Amp Nos 3 13,257.30 0.00 39,771.90

Indian-Standard - 06 Socket - Single Pole / Screw Mountable / 16

Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with Power

Cable 2.5 sq.mm 3 meter Lengt), 1 cooling Fan(230V AC - 90 CFM,

dB 42), 2nos 1U Metal Cable manager with Plastic cable loops and

SITC of 24U 600/650D UL Listed Floor mount Rack with Front

perforated door with 3 point lock, Rear mesh door with Cam lock

and 3inch Castor Wheel included with 2 no 6/16 Amp Indian-

Standard - 06 Socket - Single Pole / Screw Mountable / 16 Amp

384 73 MCB / Alternating Current - 16 Amp 3 Pin Plug with Power Cable 2.5 Nos 3 48,527.50 0.00 145,582.50

sq.mm 3 meter Length, 4nos 1U Metal Cable manager with Plastic

cable loops, 2nos CFM FAN set, 1no Monitor Tray - Ventilation -

495W - 375D and H/W screw920sets).

Supplying and fixing of following sizes of medium class PVC FRLS

conduit ISI marked along with accessories in surface/recess

385 74 including cutting the wall and making good the same in case of 0.00 0.00

recessed conduit as required as per direction of Engg.-in-Charge .

388 Subhead- 1.a (IP-PBX System) 0.00 0.00

Supplying and fixing of Hybrid EPABX system equipped with 128

389 75 Analog extensions and 6 Analog Trunk, including required hardware Set 1 177,000.00 0.00 177,000.00

and software etc as reqd.

390 76 Supplying desktop telephone sets with colour ID as reqd nos 12 1,416.00 0.00 16,992.00

391 77 S/f of 50 pair MDF box with 3 nos. krone module. nos 3 4,130.00 0.00 12,390.00

392 78 S/f of 5O pair krone box with k2 no. krone module nos 6 2,655.00 0.00 15,930.00

Supplying and drawing following pair 0.5 sq mm FR PVC insulated

393 79 annealed copper conductor, unarmored telephone cable in the 0.00 0.00

surface/ recessed steel/ PVC conduit as required.

396 S/F DP box suitable for above as reqd 0.00 0.00

397 Subhead- 3 (IP-CCTV System) 0.00 0.00

Digitally signed by VARUN

Supply, Installation, Testing & Commissioning of 5MP IP Network

TDN Low-Light IR Fixed Lens Dome/Bullet Camera, 1/2.8" CMOS or

better, 5MP (2592 x 1944) @ 25fps or better, triple stream at

various resolution & Frame Rates, Min. Illumination required 0.007

lux (color), 0 Lux IR On, 2 IR LEDs, Smart IR with upto 50m IR

distance, Auto ICR (Infrared Cut Filter) 120dB True WDR, S/N Ratio

50db, Shutter Speed 1/8 - 1/30,000; Adavance Video Compression

technology such as H.265, H.264 & MJPEG , Fixed Lens 2.8mm,

Field of View FoV H:90°, V:62°, BLC, HLC, WDR, 3DNR, White

Balance - Auto/Manual, Minimum Edge Intelligence Video Analytics :

Video Motion Detection, Tampering, Loitering, Intrusion, & People

Counting, 4 Privacy Mask, 8 Region Of Intreset, Defog, HTTPS, IP

Filter, TLS1.2, AES-128/256, SSH/Telnet closed, Stream Encryption,

2-Way Audio Full Duplex Line IN/Out, 256GB SD card support,

Alarm: 1In/1out, PoE (802.3 af) and 12V DC, Max 5W, IP 66/67 &

IK10 with Die Cast Aluminium Housing, Having Operating temp

range : –40°C to 60° C. Certifications: ONVIF Profile S/G/T

compliant,, CE (EN 50130-4), FCC Part 15, EN 55032 & RoHS

(EN63000)/NDA/STQC compliant.

Supply , Installation, testing , commissioning of 32 Channel NVR

with 4 SATA; 384 Mbps incoming bandwidth, Up to 8 Megapixels

Resolution Display and Recording, H.265 video compression

technology with real time encoding, Full function CMS (Central

monitoring software) supported, Two way audio supported, Dual

streaming technology to encode recording stream and

399 81 network stream separately, Supports remote monitoring on Mobile Nos 1 90,624.00 0.00 90,624.00

Client (Android, IOS), TCP / IP, PPPoE, DHCP, DNS, DDNS, UPnP,

NTP, SMTP, Time/ Date, Alarm, Motion Detection & Exact Search

(accurate to second), Record Snapshot, FTP, Preset Calling, Email

notification supported, Manual/ Alarm/ Motion Detection/

Continuous,CE,FCC,RoHS).

Supply, Installation,Testing & Commisioning of Surveliance 10 TB

SITC of 55" UHD IPS Commercial Digital Display for Small Size

Discussion & Chambers: Brightness (440 nits or higher), Dynamic

Contrast Ratio (Dynamic MCI (Hz)):1000000:1), 1000000:1, Static

(Panel) Contrast Ratio-1200:1, Response Time (G to G)-8 ms,

401 83 Refresh Rate.-60 Hz, Life span (hrs)-30,000, Speaker (Sound Nos 2 110,777.22 0.00 221,554.44

Output):10W + 10W, Speaker System: 2.0 ch, DVB-T2/C

Broadcasting System, Commercial Smart UX, webOS version

(webOS 6.0), BIS Certification with 3 years onsite warrenty.

Supply and Laying of cat6 23Awg UTP cable through existing conduit,

403 PA SYSTEM 0.00 0.00

Supplying, installation, testing & commissioning of digital audio

404 85 amplifier 1000 Watt, 25V rms operating at 240 Volt AC Supply Nos. 1 85,328.16 0.00 85,328.16

complete as required.

Supplying, installing, testing and commissioning 8 zone voice alarm

405 86 controller with USB mp3 am/fm player included 8 zone button Nos. 1 143,960.00 0.00 143,960.00

paging station and microphone.-

Supplying, installation, testing & commissioning of ceiling/wall

406 87 mounted loud speaker, 3/15 Watt in ABS enclosure complete as Nos. 6 3,827.92 0.00 22,967.52

Supplying, installing, testing and commissioning of 6 Watt ceiling

mounted speakers with built in line matching transformer, grill flush

mounting type in side the utility rooms with back box as required

Supplying, installing, testing and commissioning of 6 Watt wall

408 89 mounted speakers with built in line matching transformer, grill flush No 9 2,350.56 0.00 21,155.04

mounting type in side the utility rooms.

Supplying and drawing of speaker cable Single pair, 2-core, 1.5

sqmm in existing conduits.

410 13 PASSENGER LIFT WITH WIRRING(1.1) 0.00 0.00

Supply,Installation, Testing & Commissioning of of 13 Passenger lift

gearless with Machine room Capacity(884 Kg),Elevator G+2 Floors

with ACVVVF drive/Control with ARD 1.25 MPS, SS honeycomb

interior ,2hr fire rated door with simplex operation without

attendant car position indicators,battery operated alarm bell &

emegency light,SS honeycomb finish door finished car interior,

recess Granite flooring ,power operated centre opening automatic

sliding SS honeycomb finish doors for car entrance & hoist way

411 91 entrance etc . Machine beams,buffer support channels,facia plate JOB 2.00 1937985.98 3,875,971.96 0.00

including sills pit ladder metal screen in Elevator pit etc.as per

specifiaction including cost of (i)Overload detection,(ii)Voice

announcement,(iii) Intercom,(iv)Braille Buttons with all Civil &

Electrical works required for installation of Elevator in the existing

lift well and machine room,scaffolding ,floor cutting including

Fireman's switch complete in all respect.The Elevator should be

suitable for physically handicapped person.

412 Sub-Total of Electrical Works 8,126,280.63 7,220,628.86

413 Firefighting Works

414 FIRE PUMP ROOM EQUIPMENT

Supplying, installing testing and commissioning of electrical motor

driven Main Pump of horizontal centrifugal end suction backpull

out type with gland packing and capable to deliver 1620LPM (96

m³/ Hr) at 70 MWC with all necessary accessories like bronze

impeller, stainless steel shaft along with anti-vibration mounting,

coupling, coupling guard and base plate for pump, fabricated mild

steel channel,foundation bolts, and pump should have the dry run

sensor provision, etc., as per local fire brigade requirement . The

pump shall capable to have 3.5 kg/cm² residual pressure at top

most hydrant point. The pump shall be coupled to electrical motor

with speed of 2900 RPM, Electric supply 415V, 50 Hz and complete

set shall be mounted on a common base frame. The quoted rate

shall includes providing & fixing of coupling, coupling gaurd and

Foundation bolts etc.

Digitally signed by VARUN

Supplying, installing and commissioning of Diesel Engine driven

common stand by pump, horizontal centrifugal end suction backpull

out radiator cooling type with gland packing and capable to deliver

1620 LPM (96 m³/ Hr) at 70 MWC with all necessary

accessories like bronze impeller, stainless steel shaft along with anti-

vibration mounting, coupling, gear box, base plate for pump,

fabricated mild steel channel with foundation bolts etc., It includes

providing and fixing fuel oil tank (capacity as perTAC

requirements) with supports and necessary pipe works for diesel

engine, battery and battery charger to be connected to control panel

of diesel engine and exhaust silencer including necessary pipe work

and lagging, pump should have the dry run sensor provision, etc.,

and shall be automatic in operation with diesel engine control diesel

engine control panel with 24V DC storage battery & its battery

charger with required Ampere - hour rating, terminal box (2 nos.

of 12volts), as per TAC including all assocoints etc. Setting the pi

Supplying, installing and commissioning of electrical motor driven 1

Jockey pump of horizontal centrifugal end suction backpull out type

with gland packing and capable to deliver 180LPM (10.8 m³/ Hr)

at 70 MWC with all necessary accessories like bronze impeller,

stainless steel shaft along with anti-vibration mounting pad and

419 3 flexible connections at discharge end of the pipes, pump should No. 146143.00 0.00 146,143.00

have the dry run sensor provision etc. and shall be automatic in

operation.The pump shall be coupled to motor of with speed of

2900RPM and complete set shall be mounted on common base

frame. The quoted rate shall includes providing & fixing of coupling,

coupling gaurd and Foundation bolts etc.

421 Control Panel for Fire pumps. 0.00 0.00

Supply,Installation,Testing & Commissioning of dust and vermin

proof front operated compartmentalised cubicle type control panel

suitable for operation on 415 Volt, 3 ph, 50 c/s power supply with

180 Amp TPN Aluminium busbar fabricated out of 2 mm thick CRCA

sheet duly powder coated after treatment in 7 tank process with top

entry cable gland plate including interconnections, earth bus as

required comprising of :

INCOMING: One(1)- 160 Amp 25 KA 3P with solid neutral SDFU

Voltmeter with s/s, Ammeter with S/s, 3 Nos 100/5 metering CTs of

Class 1.0, ON/ OFF indicating lamps, 3 Nos Phase indicating lamp

OUTGOING: a)one(1)-125 Amp 3PMCCB,25kA with star delta

422 4 starter suitable for motor with O/L release, ON/ OFF push button, No. 1.00 253700 0.00 253,700.00

ON/ OFF indicating lamp, 3 Nos CTs metering CTs 100/5, Ammeter

b) 1 No (Outgoing) – 63 Amp 3PMCCB, 25Ka with star delta starter

suitable for motor with O/L release, ON/ OFF push button, ON/ OFF

indicating lamp,3nos 50/5 CT,Ammeter,S/S

c) 1 Set – Relay, Auto/ Manual Selector Switch, Battery Charger,

Annunciation Panel, Control wiring of pressure switches, flow

switches and starters etc as required for auto and manual operation

of Jockey pumps, Main Electric Pumps and Diesel Engine Pump as

per direction of Engineer-in-charge.d)1 lot control wiring from

pressure switch to panel board through auxiliary contactor with 1.5

sq. mm unarmoured PVC insulated ,PVC sheathed copper cable etc

423 FABRICATED - CPRI APPROVED 0.00 0.00

424 1100 V GRADE POWER / CONTROL CABLES 0.00 0.00

Supplying, laying, testing & commissioning of FRLS, XLPE insulated,

PVC outer sheateh, steel armoured, aluminium / copper conductor,

1100v grade power cables with glands etc. The cables shall be laid

in tray / Hume pipe / in trenches/on walls/ floor etc. as required.

For cables laid out door the rate shall include earth excavation

providing brick and sand protection, refilling and compacting the

earth.The rate shall excludes tray & Hume pipes. The quoted rate

shall includes the end termination for 1.1KV cables with double

compression type cable gland and heavy duty tinned copper

cable sockets as per the relevant IS standards. Rate shall be

inclusive of all sundry materials like adhesive tape , PVC sleeves ,

bolts and nuts, washers etc. including plugging unused holes.

Above 10 mm² shall be aluminium conductor type. The minimum

size of the cables shall as mentioned below,

426 5.1 a)3 core x 35 sqmm Aluminium conductor cable Rmt 25.00 483.8 0.00 12,095.00

427 5.2 b) 3 core x 10 sqmm Aluminium conductor cable Rmt 13.00 339.84 0.00 4,417.92

430 5.5 e) 3 core x 6 sqmm Aluminium conductor cable Rmt 30.00 221.84 0.00 6,655.20

431 CABLE TRAY 0.00 0.00

Supplying and fixing of perforated G.I.sheet cable tray with

neccessory angle iron suspension supports, anchor fasteners etc.

432 6 complete. Maximum height of suspension shall not exceed 500 Rmt 49.00 708 0.00 34,692.00

mm.Size of the tray shall be suitable for laying the above mentioned

G.I. Earthing strips of 50mm x 6mm thick, strip shall be run on floor

/ ceiling / walls, from the equipment to the nearest Earth pit with

necessory accessories as required. ( Earth pit shall be executed

by other agencies).

Supplying, installing, testing and commissioning of MS Pipes, ERW

confirming to IS 1239 Pt - I HEAVY grade up to 150mm dia and

pipes 200mm dia and above shall be M.S as per IS: 3589 with

434 8 painting, suitable type of supports, anchor fasteners, bolts nuts, 0.00 0.00

clamps, "U" bolts, malleable specials such as Reducers,Tees,

elbows, flanges. Including cutting, Welding, fixing in / on walls,

ceiling by using suitable supports etc, complete.

Digitally signed by VARUN

Supplying, installing, testing and commissioning of C.I. waffer type

440 9 Non-return valves ( PN 16 ) swing check type with required flanges, 0.00 0.00

nuts, bolts and gaskets etc. complete.

Supplying, installing testing and commissioning of Cast Iron Body

443 10 flanged Y-type Strainer with SS screen complete with suitable 0.00 0.00

flanges, nuts, bolts, gaskets etc. complete.

Supplying, Installing, testing and commissioning C.I. butterfly

446 11 valves as per BS 5155 slim seal standared lever operated type with 0.00 0.00

required flanges, nuts, bolts etc. complete.

Supplying, Installing, testing and commissioning of CI Gate valves

450 12 as per IS:14846(PN 1.0 Rating for suction side of the pumps) and 0.00 0.00

rising sprindle type with flanges, bolts ,nuts, washers , gaskets etc.

Supplying, installing, testing and commissioning of Gun metal

chrome finished Ball valves with fittings of screwed end type.

Supply and installation testing and commissioning of differential

Pressure switches of suitable range (0 to 12 bar) for pumpsets

complete with necessay Ball valves, Fittings like unions / colors /

Supply and installation testing and commissioning of Pressure

gauges of suitable range (0-16 bar), 100 mm diameter dial for

pumpsets completes with necessary Ball valves, siphon, Fittings like

unions / colors / reducers etc.

Supply, fixing, testing and commissioning of air vessel tank shall

be fabricated out of of 200 mm dia MS pipe to 1200 mm long

complete with 25mm inlet, 25mm drain, 25mm dia connection for

456 16 air release valve including legs, painting with red oxide primer and No. 2.00 21245.90 0.00 42,491.80

finished with fire red enamel paint. It shall be inclusive of all

relevant pipes, valves, specials upto pump header and other

accessories etc.

Exhuast pipe for Diesel engine of 80 mm dia M.S. Medium grade

with mineral wool insulation with aluminum sheet. The quoted rate

457 17 shall include 100 mm diameter MS pipe medium grade conforming Rmt 9.00 1392.40 0.00 12,531.60

to IS 1239 Part-1 and mineral wool insulation with aluminum

sheeting and Pipe supports also.

458 HYDRANT SYSTEM 0.00

Supplying, installing, testing and commissioning of MS Pipes, ERW

confirming to IS 1239 Pt - I Heavy grade up to 150mm dia and

pipes 200mm dia and above shall be M.S as per IS: 3589 with

459 18 painting, suitable type of supports, anchor fasteners, bolts nuts, 0.00

clamps, "U" bolts, malleable specials such as Reducers,Tees,

elbows, flanges. Including cutting, Welding, fixing in / on walls,

ceiling by using suitable supports etc, complete.

Excavation of trenches up to 1.5 mts. in depth, for laying pipes up

to 150mm dia. Including forming bottom surface to required level,

refilling the trenches with selected excavated earth around the pipe

in layers of 150mm thick, watering, consolidating.

465 19.1 Excavation in all kinds of soil Cum 100 649.00 - 64,900.00

If required , it will be paid as per actual measurement certified by

client 's Engg.

Supplying and wrapping of anti corrosive bituminous tape on

bituminous paint.

If required , it will be paid as per actual measurement certified by

client 's Engg.

Supplying, installing, testing and commissioning of C.I. waffer type

469 21 Non-return valves ( PN 16 ) swing check type with required flanges, 0.00

nuts, bolts and gaskets etc. complete.

Supplying, Installing, testing and commissioning C.I. butterfly

471 22 valves as per BS 5155 slim seal standared lever operated type with 0.00

required flanges, nuts, bolts etc. complete.

Supplying, Installing, testing and commissioning of CI Gate valves

473 23 as per IS:14846(PN 1.0 Rating for suction side of the pumps) and 0.00

rising sprindle type with flanges, bolts ,nuts, washers , gaskets etc.

475 Supplying, erecting and commissioning of Hydrants 0.00

Single headed hydrant valve as per IS 5290, made of SS with 63

476 24 mm dia instantaneous outlet of 80 mm dia fanged inelt ,Blank caps , No. 9 8,130.20 - 73,171.80

chain and hand wheels etc complete.

477 25 SS short branch pipe with nozzle conforming to IS 903. No. 9 2,808.40 - 25,275.60

M.S. Hose Box wall mounted type fabricated out of M.S. sheet of 16

swg. with glass fronted ( 4mm thick glass with rubber beeding) door

478 26 and size of the cabinet shall be 750mm x 600 mm x 250 mm No. 9 6,254.00 - 56,286.00

Quoted rate shall be includes suitable stand for mounting, all

fasteners etc, and cabinet shall be powder coated of approved

colour both inside and outside.

15 M long, 63mm dia RRL hose conforming to IS 636 Type A with SS

479 27 instantaneous couplings and Hoses shall be stored inside fire Hose No. 9 6,926.60 - 62,339.40

Digitally signed by VARUN

First aid Hose reel drum of 180° swinging type with 19mm dia

Rubber braided hose of 30M. length with Ball Valve and 6mm

diameter Shut off nozzle, complete. The hose reel shall conforming

Supplying, installing and commissioning of fire brigade inlet

481 29 connection of 4 way with each of 63 mm dia. built - in Gun metal No. 1 14,868.00 - 14,868.00

instantaneous coupling type arranged on 150 mm dia.

Supplying and fixing of 25mm dia automatic air release valve spring

loaded type complete with unions etc. complete.

483 AUTOMATIC SPRINKLER SYSTEM 0.00

Supplying, installing, testing and commissioning of MS Pipes, ERW

confirming to IS 1239 Pt - I Heavy grade up to 150mm dia and

pipes 200mm dia and above shall be M.S as per IS: 3589 with

484 31 painting, suitable type of supports, anchor fasteners, bolts nuts, 0.00

clamps, "U" bolts, malleable specials such as Reducers,Tees,

elbows, flanges. Including cutting, Welding, fixing in / on walls,

ceiling by using suitable supports etc, complete.

Supplying, Installing, testing and commissioning of C.I. wafer type

493 32 butterfly valves as per BS 5155 slim seal standared lever operated 0.00

type with required flanges, nuts, bolts etc. complete.

Supplying, installing, testing and commissioning of conventional

Sprinkler quartzoid bulb type with 15mm screwed end connection of

496 33 68 deg. C. temperature rating, K 80 and orifice shall not be less 0.00

than 12.7mm.Sprinklers shall be UL Listed / FM approved with

Chrome finished.

498 33.2 Sidewall sprinkler No. 30 637.20 - 19,116.00

SITC of standard response glass bulb type UL approved 93 degree

499 34 rated brass concealed pendent sprinklers having 15 mm NPT 0.00

connection with all accessories.

500 34.1 5 mm glass bulb 79 deg. Side Wall Sprinkler No. 2 637.20 - 1,274.40

Supplying, installing, testing and commissioning of hydralically

operated Sprinkler control valve complete with water motor gong

501 35 bell, basic trims as required, pressure gauges, pressure switch, 0.00

drain valves, ball valves etc. complete. Alarm valve shall be UL

Listed / FM approved.

Providing and fixing of Stainless steel corrugated flexible pipe(hose)

for dropping sprinklers below false ceiling, pipe shall be 16 bar

pressure rating and 1000 mm long 25 mm dia with union / reducer

collar, clamps etc. as required.

504 UL LISTED 0.00

Providing and fixing of electric flow switch with mechanical time

delay feature capable of sensing a minimum of flow of one sprinkler

, including making electrical cable termination through input module

& integrated with Fire Alarm System.

506 AUTOMATIC FIRE DETECTION AND ALARM SYSTEM 0.00

Supply, Installation,Testing & Commisioning of Microprocessor

based Addresable fire alarm control panel , fully networkable with

each loop capable of taking 99 devices, 8 line x 40 character alpha-

numeric liquid crystal display .The panel shall be soft addressable

type . The panel shall be able to give pin point location of all

fire/fault conditions. Further, the panel must be able to

507 38 automatically switch off respective control switches when ever any 0.00

alarm is triggered. The panel shall have integral SMF lead acid

batteries with sealed cells of 24 V capable of running for a minimum

of 8 hours with integral battery charger complete as required and as

per specification. The fire alarm panel shall be suitable for software

integration with BMS & PA system.

Supplying, installing, testing and commissioning of Addressable

Manual Call Point with back box.

Supplying, installing, testing and commissioning of Analogue

Addressable Loop powered Sounder with strobe light.

Supplying, installing, testing and commissioning of photo electric

511 38.4 adressable multi sense smoke detector with inbuilt isolator No. 161 3,953.00 - 636,433.00

module,base, junction box and other accessories.

Supplying, installing, testing and commissioning of rate of rise heat

detector with base, junction box and other accessories.

Supplying, installing, testing and commissioning of 2C x 1.5 mm²,

armoured, single stand, outer sheathed, FRLS, PVC insulated copper

conductor cable confirming to specified IS standards .

514 FIRE EXTINGUISHERS 0.00

Providing and Fixing ISI marked ABC stored pressure type Fire

extinguisher of 6 Kgs. Capacity confirming to IS: 15683 with

515 39 discharge hose, nozzle, Mono Amonium Phosphate base & ABC No 12 3,851.52 - 46,218.24

powder pressurised with nitrogen gas carrying handle and wall

mounting bracket etc as required.

Providing and Fixing of 4.5 Kgs. Capacity CO2 gas type ISI marked

fire extinguisher (IS: 15683) fitted with high pressure 1 mtr. Long

discharge hose & horn complete with refill gas, carrying handle and

wall mounting bracket etc as required.

Providing and Fixing of of 2 kG capacity Eco Friendly, Stored

pressure type filled with HFC 134 A ( clean agent fire extinguishant

having Zero Ozone depletion potential ) Clean Agent Fire

517 41 Extinguishers with safety seal, pressure guage, controllable No. 6 14,455.00 - 86,730.00

discharge mechanism, helium leak detection tested and conforming

to IS 15683 complete with initial charge as required.

Digitally signed by VARUN

Providing and Fixing of Mechanical Foam type fire extinguisher 9Lts.

Capacity, with initial filling in brand new cylinder with powder coated

518 42 finish, fitted with Gun metal union, high pressure CO2 gas cartridge, No 3 4,317.62 - 12,952.86

hose and ABS type branch pipe and wall mounting bracket etc.

complete, confirming to IS: 15683.

Fire buckets round bottom type enamel painted, white inside & Red

519 43 out side and Letter "FIRE" in black out side and handle with No 9 767.00 - 6,903.00

mounting bracket.

Fire bucket stand fabricated by MS angles to install 2 Nos. of

521 SIGNAGES 0.00

SIGNAGES:-Providing and installing in position the following type of

sign boards made out of 3mm thick flexyle photoluminescent based

glow in dark sheeting with luminous properties enclosed in a

522 45 weather proof Uvstabilized film with UV screen printing by imported Sqinch 972.22 21.24 - 20,649.95

links pasted over3 mm thick cast acrylic from front side with 6 mm

thick acrylic, -20 to+80 deg C, Suitablefor indoor use, greenish

yellow, glow visible upto 4-6 hr in total darkness.

523 46 Illumination Glow light for Exit Indication with Battery Back-up. Nos. 7 7,670.00 - 53,690.00

S/F of evacuation plan- outer cover 3 mm thick photolluminiscent

plastic, paint highest quality UV resistant glass paint frame

Aluminium made material non-radioactive, non phosphorous, non-

toxic and laed free , glowing time ≥ 3000 mins luminance

215mcd/sqm warranty 5 years as the direction of Eng-in-charge(A1)

size on steel frame with cc work.

S/F of evacuation plan- outer cover 3 mm thick photolluminiscent

plastic, paint highest quality UV resistant glass paint frame

Aluminium made material non-radioactive, non phosphorous, non-

toxic and laed free , glowing time ≥ 3000 mins luminance

215mcd/sqm warranty 5 years as the direction of Eng-in-charge(A3)

size on steel frame with cc work.

526 Sub-Total of Fire Fightening Works 6,508,510.61

527 AIR CONDITIONER 0.00 0.00

528 Supply of A,C with indoor and outdoor unit 0.00

1.5 TR high wall 5 star inverter type split A.C machine (BTU/Hr-

18000)with copper condensor & evaporator having ambient

temperature 52 degree celcius with comprehensive 1 year

warranty,5 years warranty on PCB, 10 years warranty on compressor

2.0 TR high wall 5 satr inverter type split A.C machine (BTU/Hr-

21000-24000) with copper condensor & evaporator having ambient

temperature 52 degree celcius with comprehensive 1 year

warranty,5 years warranty on PCB, 10 years warranty on compressor

531 REFRIGRANT PIPING

Supply,installation of hard/soft copper refregrant piping,complete

532 3 with fitting of bends and other nesessary material to complete the

533 3.1 1 TR to 3 TR high wall split A.C mtr 100 988.84 98,884.00

534 FRAME WORK

535 4 Supply,installation & fabrication of MS base frame for both indoor

and outdoor unit and other nesessary material to complete the job.

536 4.1 1 TR to 3 TR high wall split A.C no 23 2124.00 48,852.00

537 DRAIN PIPING

Supply,installation & fabrication of Insulated drain water piping

538 5 from indoor to nearestdrain point separate to all and other

nesessary material to complete the job.

540 CONTROL CABLE

Supply,laying of control cable and other nesessary material to

complete the job.

542 6.1 For 1 TR to3 TR high wall split A.C mtr 115 145.14 16,691.10

543 6.2 Supply and fixing of 4kVA Voltage stabilizer no 20 9383.36 187,667.20

544 6.3 Supply and fixing of 5kVA Voltage stabilizer no 3 10466.60 31,399.80

545 6.4 Sub-Total of Air Conditioner Works TOTAL 2,052,130.92

Digitally signed by VARUN

Abstract Estimate :CONSTRUCTION OF ACADEMIC BLOCK PHASE-II AT RAVENSHAW UNIVERSITY MAHANADI CAMPUS,CUTTACK,ODISHA.

Abs. Non-Schedule Non-Schedule

Head Description of Item Unit Qnty. Schedule Rate Schedule Amount

Sr. Rate Amount

Civil Works 0.00 0.00

Earth work in excavation of foundation trenches in

ordinary soil including dressing of sides and levelling the

bed up to the required depth and depositing the

1 1 excavated materials away from the work site within

50m initial lead & 1.5m initial lifts with sundries & T&P

required for the work complete including cost of all

labour,labour cess,T&P,sundries etc. as directed by the

2 1.1 Engineer

Building in charge. Cum 1258.88 243.20 306,157.10 0.00

Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc., in layers not

3 2 exceeding 20 cm in depth, consolidating each deposited 0.00

layers by ramming and watering, lead up to 50 m and

lift up to 1.5 m.

Supplying and filling in foundation and plinth with good

quality river sand including watering, ramming with

5 3 cost, conveyances, royalties of all materials and cost of 0.00

all labour with T&P required for the work etc. complete

as per specification & direction of Engineer-in-charge

Providing & applying of pre constructional anti-termite

treatment by drilling 12mm dia holes at distance of

30cm @ junction of wall & floor about 300mm apart

deep enough to reach the soil below & chemical

emulsion (IMIDACHLOPRIED 30.5SC mixed with 47.5ltr

7 4 water) pumped these holes to soak the soil @ 1 ltr Sqm 1941.00 177.00 0.00 343,557.00

solution of each hole as per manufactures specification

& the holes should be pluged the filling materials

including cost of all materials, labour,conveyance, T&P ,

all taxes and hire charges of machinaries as per

direction of Engineer-in-charge.

Boring, providing and installation bored cast-in-situ

reinforced cement concrete piles of grade M-25 of

specified diameter and length below the pile cap, to

carry a safe working load not less than specified,

excluding the cost of steel reinforcement but including

the cost of boring with bentonite solution and

temporary casing of appropriate length for setting out

and removal of same and the length of the pile to be

embedded in the pile cap etc. by percussion drilling

using Direct mud circulation (DMC) or Bailer and chisel

technique by tripod and mechanical Winch Machine all

complete, including removal of excavated earth with all

its lifts and leads (length of pile for payment shall be

measured up to bottom of pile cap).

Cement concrete of proportion (1:3:6) in foundation

and floors using 4cm size clean hard black crusher

broken granite stone metal of approved quality and

from approved quarry including hoisting, lowering and

10 6 laying concrete in layers not exceeding 15 cm. (6") Cum 374.21 7672.83 2,871,216.02 0.00

thick to the required level ramming, watering, curing

etc. complete including cost, conveyance, royalties of all

materials with all labour and T&P required for the work

etc. complete in all respect and as per the direction of

the Engineer-in-charge.

Plain cement concrete (1:2:4) using 12mm size black

hard crusher broken granite chips of approved quality

from approved quarry including hoisting, lowering and

11 7 laying concrete in layers, watering, curing etc. complete Cum 30.00 9589.39 287,681.64 0.00

including cost, conveyance, royalties of all materials

with labour,labour cess and T&P etc. required for the

work complete as per the direction of the Engineer-in-

Fly Ash brick masonry in cement mortar (1:6) in

foundation & plinth using Fly Ash bricks of 23 x 11 x 8

cm size having a crushing strength of not less than 75

kg./sqcm with dimensional tolerance ± 2% including

splays cutting circular moulding chamfering and

12 8 corbelling and similar such type of works with all Cum 184.76 6413.18 1,184,899.51 0.00

necessary projections watering and curing after

immersing the bricks in water at least for six hours

before use including cost, conveyance, and royalties of

all materials with all labour,labour cess and T & P

required for the work complete in all respect as per

Digitally signed by VARUN

Fly Ash. brick masonry of size 23 cm. x 11 cm. x 8 cm.

having crushing strength not less than 75 kg. Per Sqr.

Cm. in cement mortar of mix (1:6) with approved grade

cement and screened & washed sand for mortar after

immersing the bricks for 6 (Six) hours in water before

use in Superstructure including splays cutting, circular

moulding, corbelling, chamfering and similar such type

of works, watering and curing etc. including cost,

conveyance, loading, unloading, royalties and taxes of

all materials, cost of all labour, scaffolding, sundries,

T&P required for the works etc. complete in all respect

as directed by the Engineer-in-charge.

Fly Ash brick masonry in cement mortar (1:4) in super

structure using Fly Ash bricks of 23 x 11 x 8 cm size

having a crushing strength of not less than 75 kg./sqcm

with dimensional tolerance ± 2% including splays

cutting circular moulding chamfering and corbelling and

18 10 similar such type of works with all necessary projections 0.00 0.00

watering and curing after immersing the bricks in water

at least for six hours before use including cost,

conveyance, royalties and taxes of all materials with all

labour,labour cess and T & P required for the work

complete in all respect as per direction of Engineer-in-

Providing, lifting, hoisting and laying Reinforced cement

concrete of M-25 grade as per approved designs and

drawings having a minimum compressive strength (in

work test) 250 Kg. / Square cm. in 15 cm. cubes at 28

days after mixing and test conducted in accordance with

I.S. 516 using 12 mm. to 20 mm. size black hard

crushed broken granite stone chips and screened and

washed sharp sand for mortar of approved quality from

approved quarry, washed and cleaned ( 20mm. size

chips not to exceeds 25 % ) to be mixed in concrete

mixture with Portland slag cement (PSC) including

hoisting, lowering, laying and compaction concrete by

using vibrators, watering and curing for 28 days,

centering and shuttering then after dismantling and

removing debris from the work site and finishing the

exposed surface smooth providing grooves or beads

wherever necessary including cost, conveyance, loading,

unloading, royalties and taxes of all materials and cost

of all labours, sundries, T & P required of the work etc.

complete in all respect as directed by the Engineer-in-

Charge. But excluding cost and conveyance of M.S. rods

or Tor steel and binding wires and labour charges for

straightening, cutting, bending etc. of M.S. rods or tor

steel tying the grills and placing in proper position.

23 11.1 Ground Floor 0.00 0.00

27 11.5 d) Column up to ceiling level Cum 101.06 19613.02 1,982,091.40 0.00

33 11.11 a) Column up to ceiling level Cum 81.50 22031.31 1,795,551.60 0.00

39 11.17 a) Column up to ceiling level Cum 69.76 24926.20 1,738,951.56 0.00

44 11.22 Terrace floor 0.00 0.00

45 11.23 a) Column up to ceiling level Cum 31.45 28391.51 892,912.93 0.00

Supplying Cutting, straightening coiled or bent up M.S.

Rod or tor steel of primary steel producers including

bending, binding, welding and jointing if necessary and

tying the grills and placing in position as required for

R.C.C. Work and for providing fan hooks as required,

hoisting, lowering, laying including cost, conveyances of

M.S. Rod or tor steel and binding wires of 18 to 20

gauge and labour required for the work for bending,

binding and tying the grills in all floors with labour cess

etc. (payment will be made on standard weight of B.I.S.

for M.S. Rods or tor steel only) etc. complete as per

specification & direction of Engineer-in-charge.

Digitally signed by VARUN

Providing 12 mm thick cement plaster with cement

mortar of mix (1:6) with screened and washed sharp

sand for mortar and finished smooth to the rough

surface of walls in all heights after racking out joints

54 13 including watering and curing, rounding of corners, 0.00 0.00

providing grooves where ever necessary with cost,

conveyance, royalties of all materials with cost of all

labour,labour cess, T&P, and scaffolding required for the

work etc. complete in all respect as directed by the

55 13.1 Engineerfloor

Providing 16 mm thick cement plaster with cement

mortar of mix (1:6) with screened and washed sharp

sand for mortar and finished smooth to the rough

surface of walls in all heights after racking out joints

59 14 including watering and curing, rounding of corners, 0.00 0.00

providing grooves where ever necessary with cost,

conveyance, royalties of all materials with cost of all

labour,labour cess, T&P, and scaffolding required for the

work etc. complete in all respect as directed by the

60 14.1 Engineerfloor

Providing 6 mm thick cement plaster with cement

mortar of mix (1:4) with screened and washed sharp

sand for mortar and finished smooth to R.C.C. work

after closed deep chipping & slurry treatment including

64 15 watering and curing, rounding of corners, providing 0.00 0.00

grooves where ever necessary with cost, conveyance,

royalties of all materials with cost of all labour,labour

cess, T&P, and scaffolding required for the work etc.

complete in all respect as directed by the Engineer in

65 15.1 charge.

Fixing granite tiles of approved dimension area above

0.4 sqm (20mm thick) in floor, treads of steps and

landing on 20mm thick bed of cement mortar (1:4)

jointed with neat cement slurry mixed with pigment to

match the shades of the tiles including rubbing and 0.00 0.00

polishing etc. complete with cost, conveyance, royalties

and taxes of all materials complete in all respects as per

direction of Engineer-in-Charge.

Fixing granite tiles of approved dimension area above

0.1 up to 0.4 sqm (10mm thick) in Dados, treads of

steps and landing on 12mm thick cement mortar (1:3)

jointed with neat cement slurry mixed with pigment to

match the shades of the tiles including rubbing and 0.00 0.00

polishing etc. complete with cost, conveyance, royalties

and taxes of all materials complete in all respects as per

direction of Engineer-in-Charge.

Supplying, fitting & fixing of 8-10 mm thick & size of

600x600 mm Glazed vertified floor tile (GVT) of with

veilcraft (VC/FT ) shield( Scratch free/stain free) with

water absorption limit between 0.08% to 3% and

conforming to IS : 15622:2006 (Group B Ib). laid on 20

mm thick cement mortar (1:4) (1 cement : 4 course

sand) and filling joints with white cement of approved

quality including cost of all materials, labour T&P etc.

required for the work all complete as per direction of

the Engineer-in-charge (for New Work only )

Supplying, fitting & fixing of 8-10 mm thick and size

of 600x600 mm Glazed vertified wall tile of in

dadoes, skirting and risers of steps of laid on 12 mm

thick cement mortar (1:3) (1 cement : 3 course sand)

jointed with slurry mixed with pigment to match the 0.00 0.00

shades of the tiles etc. complete including cost of all

materials, labour T&P etc. required for the work all

complete as per direction of the Engineer-in-charge.

Digitally signed by VARUN

Supplying, fitting and fixing of Antiskid Ceramic Floor

Tiles in flooring using special plain / printed series

Ceramic Floor Tile of premium grade ( having

minimum thickness 7 mm to 8 mm & size 300 mm

x300 mm, confirming to I.S 13755 of approved quality

and shade in floors, treads on steps and landings on

20 m.m thick bed of cement mortar of mix (1:4) laid in

proper slope and gradient with screened & washed

sharp river sand for mortar and fixing with neat white

85 20 cement slurry,grouting the joints with neat white 0.00 0.00

cement slurry mixed with required quantities of

pigments (Tiles are to be immersed in the water for

required time before use) of approved make to match

the shades of the Ceramic Floor Tiles if required

including cost, conveyance, loading, unloading,

stacking, royalties , all taxes, cost of all Labour, Labour

cess ,Sundries, T&P required for the work , Watering ,

Curing for required days , cleaning the flooring space

manually etc.complete in all respect as directed by the

86 20.1 Engineer-in-charge.

Supplying, fitting & fixing of 600mm x 300mm

Ceramic wall tiles having thickness 6.5mm to 7.0 mm

confirming to IS 13753 in dadoes, skirting and risers of

steps laid on 12 mm thick cement mortar (1:3) (1

cement : 3 course sand) jointed with slurry mixed with 0.00 0.00

pigment to match the shades of the tiles etc. complete

including cost of all materials, labour T&P etc. required

for the work all complete as per direction of the

90 22.1 Engineer-in-charge

Providing & Fixinng factory made 100% Solid WPC (

Wood Polymer Composite ) - Door Frame 125 mm x 65

mm Single Rebated, made from Wood Polymer

Composite ( Single Extruded Process ) material

comparising of virgin PVC polymer of K Value 57-60 (

Suspension Grade ), Calcium Carbonate and Natural

Fibers ( Wood Powder/ Rice Husk/ Wheat Husk ) and

Non toxic additives fabricated with meter Joints after

applying PVC solvent Cement & screwed with full body

treaded star headed screws having minimum frame

93 23 density of 780 kg/ cbm & an ISO 9001 - 2015 Certified 0.00 0.00

Company, having good screw holding capacity ( Screw

Withdrawal strength of ( Min. 990 N ), Minimum

Compressive Strength of 58 N/mm2, Modulus of

elasticity 900N/mm2 and resistance to spread of flame

of class A category with property of being termite /

borer proof , water / Moisture Proof & Fire retardant &

Fixed in position with SS Dash Fasteners / Hold Fast of

reuired dia and lenght, , all as per specifications

drawings as directed by the Engineer-In-Charge.

Material test certificate and authentication should be

94 23.1 compulsory

Ground floorprovided by the manufacturing company. Rmt 304.50 1477.83 0.00 449,999.84

Supplying, fitting and fixing of 32mm thick flush door

shutter with approved quality of 30mm thick BWR block

97 24 board pasted with 1mm thick sunmica on both side of 0.00

approved design and quality including cost of all door

S.S fittings and fixtures etc. complete in all respect as

per the direction of the Engineer-in-Charge.

Factory made single leaf rigid FRP(alternately called

GRP) sandwich composite door shutter of 32mm thick

laminated with two GRP skins with wood grain finish

fabricated using UV-stabilised Isopthalic Gelcoat and

one layer of 450 gsm E-glass Chopped Strand Mat

(CSM) impregnated with orthopthalic palyester resin.

The thickness of the skins shall not be less than

3.00mm Expanded Polystyrone(EPS) structural foam

panel of 29mm thickness and a density of 20kg/cu.mtr

shall be used as core material. Wooden reinforcements

made of seasoned sal wood block of cross section not

less than 28mmx32mm and also necessary sal wood

101 25 reinforcements for fitting the metal fittings such as 0.00

tower bolts, aldrops, handles etc shall be provided. A

structural adhesive compatible with (EPS) foam shall be

used for bending the core material, the sal wood

reiforcements and the skins. The material and process

for manufacturing the door shutters shall conform to RV-

TIFAC composites Design Centre's standards and

specifications and the door shutters tested in

conformation to IS: 4020-1998. The finish of door

shutter will be plain colour white/ Ivory/ Beige/ Light

grey/ Mahogany/ Teak wood or any other colour using

high quality pigments. Three heavy whight mild steel

butt hinges type-I(ISI marked) size 100mm are to be

fitted on one side of shutter with FRP frame of size

Digitally signed by VARUN

Providing and fixing ISI Marked un-insulated fire rated

door confirming to IS 3614:2021,& tested to

IS17518,and shall carry a unique label with

certification/test report number.The fire rating shall be

for 120minutes integrity only.Material shall be

galvanised steel conforming to IS 277, made out of

minimum 1.2(18 SWG) for both frame and shutter, G.I.

sheet (zinc coating 120 gsm/sqm).Frame shall be 125 x

55 grooved profile with built in rebate for fire rated

smoke seal. Frame shall be mitered and field

assembled. EPDM smoke seal to be provided along with

frame as standard. Door shutter shall be double skin of

46mm thick with required fire rating and with vision

panel. The infill material shall be resin bonded

honeycomb core. All doorset shall be factory prepped

for receiving appropriate hardware and provided with

necessary reinforcement for hinges, locks and door

closers.The door stiles should be interlocked, for pairs of

doors integral astragals has to be provided on the

meeting stile for both active and inactive leaf. Vision

lite, minimum 5mm clear fire rated glass of size 150 x

750mm (max 0.12sq.mt) on both shutters, fixing with

All frame and door shutter shall be finished polyster

powder coated to minimum 50microns, of approved

colour as per the direction of the engineer incharge.

Cost of double leaf doorset shall include following

hardware and accessories as a complete assembly. SS

ball bearing hinges of SS-304 grade of

size100x75x3mm,1no Fire rated mortise dead lock,

55mm BS, 20mm sq. forend, including escutheion, sss

as per EN 12209 with both side key cylinder on active

leaf and 2nos flush bolt on the inactive leaf in case of

double leaf door along with dust proof socket at bottom,

1pairs Pull handle D type, 22dia, CTC 300mm, back to

back per leaf, with spindle,SS 304, SS finish. 1no of

Door closer with spring size of EN 2- 4, as per EN1154

and CE marked per leaf. Suitable anchor fastners for

fixing on different type of wall construction as per

manufacturer recommendation.Once frames is installed

it shall be filled with fire rated PUF. Manufacturer test

certificates shall covers complete door set as a un-

latched assembly with a valid test certificate not

exceeding 5 years from the date of issue of report. for

more info refer doors details drawings, including cost of

all materials, all labour, sundries, T&P etc. complete in

all respect as per direction of Engineer-in-Charge.

Supplying and fixing of Powder coated 50-60 microns

approved colour of Aluminium 40mm Casement series

Door Unit with suitable aluminium extrude profiles. the

system is designed to accommodate 12mm clear

toughened glass . the rate quoted inclusive of

hardwares like antilift,roller, Espag lock cum

handle,epdm gaskets,T mullion ,Fly Mullion ,bottom

adopter ,mid transom ,glazing clip for 12 mm glass felt

along with all accessories etc complete. the gap

between the wall and window will be filled with silicon 0.00

weather sealant in the outer side. Casement Door Outer

frame - 40mm x 45.3mm Series x 1.4mm thickness, Fly

mullion - 44 x 60 mm x 1.4mm thickness, T Mullion 40

x 78.4mm x 1.4mm thickness, Transom - 40.28 x 125.8

x 1.75 mm thickness, Bottom adopter - 34.6 x 26 x

1.5mm thickness, including cost of all materials, all

labour, sundries, T&P etc. complete in all respect as per

direction of Engineer-in-Charge.

Supplying and installing UPVC- 3 track 3 shutter sliding

windows with Outer dimension - 104 x 49 sash

dimension of 61mm x 39mm for windows with corners

fusion welded, fully reinforced with Galvanized steel of

1.2 mm to 2 mm. The sash will be fitted with 5mm

reflective toughened glass . The windows must be

112 29 installed complete with all kinds of ironmongery 0.00

(including EPDM gaskets,bridging wedges and glass

packers) and with suitable water draining system.

Application of Silicon sealant from Inside / Outside of

Dowcorning / GE or equivalent including cost of all

materials, all labour, sundries, T&P etc. complete in all

respect as per approved drawing & direction of

Digitally signed by VARUN

Supplying, fitting & fixing in all floors of M.S. grills, grill

gates, M.S. gates, garage door, collapsible gates with

top and bottom rails, steel windows, critical frames for

windows, stair case and parapet railing made out of M.S

Square bar/ flat including stair case hand railing with

40mm. dia G.I.pipe etc. including painting two coats

over a coat of redoxide primer as per approved drawing

and design with cost of all materials & labour, labour

cess, T&P, sundries etc. complete in all respect as per

specification & direction of the Engineer-in-Charge.

Priming one coat with wall cement primer (water bound)

to make an even finished surface in all floors and

heights to wall surface of approved make and shade

including sand papering, applying putty wherever

necessary & cost of scaffolding, staging charges with

cost, conveyance, cost of all labour,labour cess T&P etc.

complete as per the direction of the Engineer-in-charge.

Finishing wall with textured exterior paint of required

127 32 New work (two or 0.00

more coats appplied @3.28litre/10sqm)over and

including priming coat of exterior primer applied

Finishing plastered surfaces of walls with cement based

wall putty (Water based) of approved make duly

approved by Engineer-in-Charge) and finishing the

surface smooth and even by sand papering to receive

painting in walls, at all heights with staging wherever

necessary with cost, conveyance, cost of all

labour,labourcess, all T&P etc. required for the work

complete in all respect as per the direction of the

133 33.1 Engineer-in-charge.

Painting two coats with plastic emulsion paint with a

approved quality primer to make an even finished

surface in all floors and heights to wall surface of

approved make and shade including sand papering,

137 34 applying putty wherever necessary & cost of scaffolding,

staging charges with cost, conveyance, cost of all

labour,labour cess, T&P etc. complete as per the

direction of the Engineer-in-charge.

Engineer-in-charge.

Painting two coat with approved synthetic enamel paint

to new wood work over a coat of Red oxide primer

including cost, conveyances, royalties, taxes of all

142 35 materials and cost of all labour with T&P required for

the work etc. complete as per specification & direction

of Engineer in charge.

Painting two coat with approved synthetic enamel paint

to new iron work over a coat of Red oxide primer

including cost, conveyances, royalties, taxes of all

146 36 materials and cost of all labour with T&P required for

the work etc. complete as per specification & direction

of Engineer in charge.

Supplying, fitting and fixing of Stainless steel of 304

grade in hand railing using 50mm dia of 2mm thick

circular pipe with Balustrade of size 32mm x 32mm x

2mm @ 0.90mtr. C/C and stainless square pipe bracing

151 37 of size 32mm x 32mm x 2mm in 3 rows in stair case as

per approved design and specification, buffing, polishing

etc with cost, conveyance, cost of all labour,labour cess,

T&P etc. required for the work complete in all respect as

per direction of the Engineer-in-charge.

Digitally signed by VARUN

Providing 2.5cm thick Grading Concrete over roof slab

with cement concrete (1:2:2) using 6mm size black

hard granite crusher broken chips and screened &

washed sharp sand for mortar and finished smooth to

155 38 the rough surface of slab including watering and curing

with cost, conveyance, royalties of all materials with

cost of all labour, labour cess and T&P required for the

work etc. complete in all respect as directed by the

Engineer in charge.

Waterproofing application:- Providing and application of

two component polymer modified flexible cementitious

waterproofing coating at a thickness of 1.5 -2.5 mm

The membrane should have Elongation equal or more

Crack Bridging ability : Up to 1 mm

Adhesive strength: 1.0 N/mm² @ 28d

Tensile elongation: 60% @ 20°C

Shore A Hardness >85 (between 3 - 7 days)

etc. as per direction of E.I.C (For longer span, in terrace

panel of 4m*4m should be done by groove cutting, and

filling with PU Sealant)

Supply of all materials & laying the waterproofing

material of torch shield P3160(3mm)with its primer 2

coats or equivalent water proofing material after drying

cleaning the concrete surface over the concrete

159 40 floor/roof/ balcony/sunken and dado upto 1'6" in wall

including cleaning,applying and mending as per

specification including cost,conveyance,taxes,royalities

of all materials to work site etc.all complete as per the

direction of the Engineer-in-charge.

Providing & Installation of GFRC JALI (Glass Fiber

Reinforced Concrete) thickness of 25-30 mm & Border

thickness of 50 mm with Pattern, design, and colour of

approved make to be fixed on/between RCC /Block work

Column or structural work with Dry Fixing method with

appropriate SS Pipe & Cleats frame work, using

163 41 fasteners, and necessary hardware etc. The element 0.00

shall be made from '53 grade' Portland Cement ,

Quartz, Fine Silica Sand, Alkali Resistant Glass fibre

Super plasticizers / Additives , Polymers and U.V

resistant Synthetic inorganic pigments shall be used for

pigmentation .The material casting shall take place in

Synthetic Rubber / FRP Mould

Supply and Installation of System comprises of Semi

unitized extruded aluminum Structural Glazing wall

panels comprising of extruded Vertical Aluminium

mullions and Horizontal transoms with super Durable

Powder Coating finish of minimum 60 Microns

confirming standards to withstand wind pressure. The

mullions and transoms are installed on locations as

indicated in the architectural drawings. The framing

members provide no structural support for the building

and the Structural Glazing wall is deemed to be a

lightweight façade which is intended to separate the

external from the internal of the building and provides

natural light into the building. The curtain wall system is

designed to have internal drainage system within the

167 42 extruded sections with 6MM Blue toughened glass.

Gaskets are employed as water barrier between the

aluminum gridwork and the glazed sashframe, which

are fully drained in the event of leakage past the

primary seal. The external grooves are covered with

application of backer rod with weather sealant of

approved make as indicated in the concept drawing.

Fabricating and supplying Mild Steel ( HDG coated )

Brackets to accommodate 3 Dimensional movement for

achieving perfect verticality and proper fixing of

structural glazing system with the RCC/

masonry/structural steel framework of building

structure, using stainless steel (chemical/mechanical)

anchor fasteners/ bolts, Teflon separator to prevent

bimetallic contacts with nuts and washers etc. of

168 42.1 stainless steel Grade 316, of the required capacity and Sqm 37.80 8849.67 0.00 334,517.51

Digitally signed by VARUN

Supply and Installation of 14 mm GRG Tiles steppe

edge ceiling tile of size 595 x 595 x 14 mm on the edge

& 7 mm in the center having all edges encapsulated

with chemical treated paint & having densified tegular

edge ,weight 5 kg/m2 having random circular semi

perforated in dual diameter / Random fissure semi

perforated in variable length which is suspended by

using 0.3 mm thick and 15 mm wide pre coated metal T

15 grid system. The technical parameters are as follows

: Core - GRG Silicate, Fire – Class 1 & P , Acoustics –

NRC 0.5,Climate (degree C, RH) – 50, 99, STC - 30,

Termite resistance ,Light reflectance – 85 %,Green (RC

%) – 25, Hygiene (VoC, Clean room) – Low, , Load

capacity (Kg) - Antisag. The T 15 Grid system of 600 x

171 43 600 mm module shall include wall angle(WA 15) with 0.00 0.00

unequal flanges of size 14 x 20 x 3000 mm wide, length

3000 mm, 0.43 mm thick fixed along the perimeter of

wall with the help of nylon sleeves and suitable

fasteners at 300 mm centers. Then suspend the Main

T15 (MT15 W36) having flange width 15 mm /24 mm ,

height 32/38 mm and length 3600 mm thickness 0.30

mm from the soffit with help of soffit cleat and wire at

1200 mm c/c. Cross T15 (CT15 W12) with flange width

15 mm, height 32 mm and length 1200 mm is then

interlocked into the pre-cut slots in the Main T15 at 600

mm centers in the direction perpendicular to the Main

T15. Finally, Cross T15 (CT15 W06) having flange width

15 mm, height 32 mm and length 600 mm are then

interlocked into the pre cut slots in the 1200 mm Cross

T15 at 1200 mm centers and in direction parallel to the

Vertical load testing of piles in accordance with IS 2911

(Part IV)including installation of loading platform by

Kentledge/Anchor piles method and preparation of pile

175 44 head or construction of test cap and dismantling of test

cap after test etc. complete as per specification & the

direction of Engineer in-charge.(Lab test should be

carried out of any Govt lab /NABL accreditation lab)

176 44.1 Single pile upto 128 tonne Safe capacity

177 45 Initial test (Test Load 2.5 times the Safe capacity) 1.00 668639.18 668,639.18

Lateral load testing of single pile in accordance with Each

178 46 IS:2911 part-IV for determining safe allowable lateral 1.00 64018.65 64,018.65

179 Sub-Total of Civil Works TOTAL 128,531,115.17 14,795,950.99

180 Plumbing Works

181 INTERNAL PH WORK

Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having theRmtal stability for hot & cold

water supply, including all CPVC pipes SDR-11 as per

IS-15778/2007 plain & brass threaded fittings, i/c

182 1 fixing the pipe with clamps at 1.00 m spacing. This 0.00 0.00

includes jointing of pipes & fittings with one step CPVC

solvent cement and the cost of cutting chases and

making good the same including testing of joints

complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making

good the walls etc.

Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having theRmtal stability for hot & cold

water supply, including all CPVC pipes SDR-11 as per

IS-15778/2007 plain & brass threaded fittings, including

fixing the pipe with clamps at 1.00 m spacing. This 0.00 0.00

includes jointing of pipes & fittings with one step CPVC

solvent cement and testing of joints complete as per

direction of Engineer in Charge.

194 2.1 External work 0.00 0.00

Providing all materials, labour, T&P for fitting & fixing of

following brass full way Valves in all floor & fixing with

the pipes after cutting the pipes to required shape &

size including wastage etc. of following nominal

diameter, all complete including testing the joints with 0.00 0.00

required water pressure.The cost inclusive of

transportation scaffolding etc. all complete as per

specification excluding GST and direction of Engineer-in-

197 3.1 charge.

25mm dia brass full way valve Nos 12 1430.40 17,164.75 0.00

198 3.2 32mm dia brass full way valve Nos 6 2094.03 12,564.17 0.00

199 3.3 50mm dia brass full way valve Nos 15 3935.18 59,027.73 0.00

Digitally signed by VARUN

Providing all materials labour, T&P for making grooves Mtr. 178

in bricks/stone masonary walls vertically or horizontally

up to required depth and width in all floor for laying of

pipes and fittings up to 50mm dia, testing the joints

with required water pressure and making good the

damages with cement concrete 1:2:4 with 12mm size

h.g.c.b.chips and finished smooth with cement morter

(1:4) to original shape including cost of materials,

curing, conveyance, taxes of all materials etc. all

complete as per specification & direction of EIC.

Providing all labour,T&P for cutting holes in bricks or

stone masonry wall for taking pipes in all floors and

making good the damages with cement concrete 1:2:4

201 5 finished smooth with CP 1:4 to original shape including 0.00 0.00

cost of all materials, curing, conveyance, taxes, duties

etc. all complete as per specification & direction of

Engineer-in-charge.

For 25mm to 110mm dia pipe to pass in 250mm thick No. 123

Providing all labour,T&P and cutting holes in brick No. 111

masonry wall /RCC wall for crossing of GI pipes / CI

203 6 pipes/ HCI pipes of different dia and making good to the 27,833.25 0.00

damage with (1:4) complete as per specification &

direction of EIC.

Providing, fixing, jointing and testing PP mineral filled

low noise level Soil & Waste piping system as per BS EN

1451, SN4-S16, with minimum density for pipes and

fittings 1.4 gm/cm3. Pipes and fittings made from

Polypropylene-M (mineral reinforced) and available from

50 – 160 mm with push fit SBR type rubber ring sockets

for easy installation. Pipes should have 3 layer design.

Should have hot water resistance up 95ºC for short

term loading (90ºC for long term loading). Piping

system should have chemical resistance of pH 2-12.

Fittings should have swept design from 75-160mm and

depth gauge for proper fittings against thermal

expansion and contraction, should have top marking at

every 15° intervals in angular rotation for better

alignment. Piping system includes all required fittings &

accessories such as coupler, bend, tee, Y, reducer,

access pipe, multi floor traps, Nahni trap with extension

piece etc. for conveying soil, waste & rainwater purpose

in floors, ceiling suspended, or on walls, with leak proof

joints etc. Setting the pipe in 1:2:4 CC in case of

concealed plumbing, wall chasing, holes, supporting,

clamping, covering back with chicken mesh & plaster

and making the wall good as per approved shop

drawing. Testing as per tender specifications/EIC.

110mm U-PVC SWR Pipe Mtr. 90

Supplying all materials, labour, T&P and fitting and

fixing U-PVC SWR soil waste ventilating pipes and

fittings of the following outside diameter conforming to

ISI No 13592/1992 to walls with nails, bobbins and

wooden plugs or laying in trenches including jointing

207 8 with supply of approved rubber lubricant by non-heat 0.00

application method/as per manufacturer's specification,

testing, earthwork in excavation in all kinds of soil and

refilling of trenches , cost & conveyance of all materials

to worksite, payment of taxes etc. all complete as per

P.H specification and direction of the Engineer-in-charge.

211 8.4 110mm U-PVC offset without ear Each 30 480.73 14,421.96 0.00

Providing all materials, labour, T&P European type NOS 37

218 9 floor mounted WC with seat, white plastic lid and 13293.290 491,851.73 0.00

flushing PVC cistern as per specification of Hindware

Popular (Starwhite),

Supplying, installing, testing and commissioning of

approved make White Viterous urinals 3.8 LPM urinal

219 10 with Urinal valve Autoclosing system with Built-in Each 26.00 8437.94 219,386.54 0.00

control cock & wall flange. Urinal size-355X340X535 MM

confirming to IS 2556: Part 6 -1996 etc all complete

as per specifications.

Supply all materials and labour for fitting and fixing of

following size Half Pedestral Wash Basin with fixing

Accessories,Size-550X400 mm, of approved make in all

floor of approved quality including cutting the walls &

220 11 floor and making good the damages with cement 0.00 0.00

concrete etc. including all taxes, duties, transportation

etc. all complete as per direction of EIC.

Digitally signed by VARUN

Under Counter Wash Hand Basin.

(,Size-605X415X200 mm )

Wall Hung Half pedestral wash hand basin

Supply,fitting and fixing all materials, labour, T&P as per

specification , the following Brass/ CP / G.M. fittings at

223 12 appropriate locations to thr pipe lines at all floors and at 0.00 0.00

all heights, of approved make confirming to relevent IS

specification . etc complete in all respect.

Brisk Health Faucet ABS with Rubbit cleaning

224 12.1 system,1.25 m Long SS Flexible Tube & ABS Wall Hook . NOS 37.00 1501.94 55,571.69 0.00

225 12.2 Two-way Bibcock with wall Flange. NOS 37.00 1964.94 72,702.63 0.00

226 12.3 One-way Bib cock with wall Flange. 0.00 2330.76 0.00 0.00

228 12.5 15mm dia Angle Stop cock with Wall Flange. NOS 189.00 1,468.86 277,615.30 0.00

229 12.6 15mm dia Concealed stop cock with wall flange. NOS 26.00 863.17 22,442.42 0.00

Supplying all materials, labour, T&P and fixing mirror of

superior glass mounted on 6mm.thick A.C. sheet or ply

230 13 wood sheet and fixed to wooden plugs with CP screws 0.00 0.00

and washers complete as per specification and direction

of Engineer in charge.

232 13.2 Soap dish in each toilet . NOS 37.00 1,015.15 37,560.70 0.00

32 mm C.P. Bottle Trap 32mm with 125 & 175mm

233 13.3 Long Wall Connection pipe & wall Flange 64.00 119,193.22 0.00

Waste coupling 32mm Size Full Thread with 80mm

height or equivalent. No. 645.58

235 13.5 15mm CP Extension piece Each 126.00 62.07 7,820.57 0.00

236 13.6 110 mm dia CP Nahani trap with Grating 71.00 389.40 27,647.40 0.00

Supplying all materials, labour, T&P and providing fitting

and fixing (Aqua guard) Pure Chill 120 PSS UV (Eureka

Forbes)of size 750x570x1350mm height with water

237 14 storage capacity 120 liters along with 3 nos of faucets 2 Nos 2.00 154,893.88 309,787.76 0.00

for cold water and 1 for normal water including a flow of

1.5 ltr per minute etc all complete as per approved

drawing,specification and direction of the Engineer in

charge. & fixing Ductile Iron Pipes Pressure ,socket

and spigot pipes conforming to IS : 8329 :2000

238 15 (Complete With all joints & Fittings) with DI pipes of K-7 0.00

239 15.1 100 mm Ductile iron Class K-7 pipes meter 185.00 1210.98 224,030.38 0.00

Supplying all materials, labour, T&P and fitting and

fixing of Cast Iron Sluice Valve with double flanged ends

works purposes conforming to IS 14846 - 2000

(Standard) etc all complete as per the direction of

Engineer-in-charge.

Cast Iron Reflux Valves (Non-return valves) with double NOS 2

flanged ends conforming to IS : 5312 (Part-I) - 2004

243 SINTEX TANK FOR OVER HEAD 0.00 0.00

Fixing double layer cylinderical water storage tanks

conforming to IS: 12701--1996 including cutting holes

through the tank and fixing mild steel tubes and fittings

244 18 and providing extra sockets and jam nuts, fixing ball 0.00 0.00

valve etc, including hoisting upto a height and placing

the tank to the required position etc all complete as per

specification and direction of the engineer in charge.

245 18.1 DOMESTIC WATER TANK 2000 LIT. PVC TANK EACH 7 54387.94 380,715.56 0.00

246 18.2 FIRE WATER TANK 5000 LIT. PVC TANK EACH 2 123130.84 246,261.69 0.00

247 Ball Float (Mechanical) 0.00 0.00

Supply, Installation & commissioning of reputed make Nos 5

mechanically operated ball float with Brass Arm for each

248 19 tank for closing & opening the inlet of each tank as per 4799.06 23,995.30 0.00

the water level in each tank suitable for handling 10 Bar

249 Sub-Total of Plumbing Works TOTAL 3,924,179.91 0.00

250 Electrical Works 0.00

251 Sub-Head I (modular Wiring Items)

Recessed wirring to light point/ fan point/ exhaust fan

point/ call bell point with 1.5 sq.mm FRLS PVC insulated

copper conductor of ISI marked Mak with 20 mm dia

HMS FRLS PVC conduit ISI marked ) and ceiling rose

ISI marked of modular type G.I box with metallic cover

plate (both side) ( flame retradant type) - of suitable

size, modular box with 1.5 sq. Mm FRLS PVC insulated

252 1 single core multistandard copper conductor as earth 0.00 0.00

wire including all accessories and connection as per

direction of Engineer -in -Charge. . All the switches &

sockets should be warrantied for a replacement period

of 2 years against defects with ncessary test report &

Warrnaty certificate to be submitted to the department

for genuinity of product & to avail free after sales

service within warranty period for acceptance of

Digitally signed by VARUN

Supplying ,fixing of 6A Plug on the same board in

existing switch board with complete fitting by 01 no of

6A switch & socket (modular type)( ( flame retradant

type)) & other required accessories of ISI marked as

approved as per direction of Engg. -in -Charge.

256 2 .(Maximum 02 nos point in one circuit).All the switches Nos 60 231.28 13,876.80 0.00

& sockets should be warrantied for a replacement period

of 2 years against defects with ncessary test report &

Warrnaty certificate to be submitted to the department

for genuinity of product & to avail free aftersales service

within warranty period for acceptance of materials.

Supplying,fixing of 6A Plug on the separate board with

complete fitting by 01 no of 6A switch & socket(modular

type)( ( flame retradant type)) with suitable size

modular box & cover( falme retradant type) including

supplying of all required accessories of ISI marked as

approved as per direction of engg-in-charge..

257 3 .(Maximum 02 nos point in one circuit).All the switches Nos 80 650.18 52,014.40 0.00

& sockets should be warrantied for a period of 2 years

against manufacturing defects against which ncessary

test report & Warrnaty certificate to be submitted to the

department for genuinity of product & to avail free

aftersales service within warranty period for acceptance

Supplying,fixing of 1x16A Plug on the separate board

with complete fitting by 01 no of 16A switch &

socket(modular type)(( flame retradant type)) with

suitable size modular box & cover( flame retradant

type) including supplying of all required accessories of

ISI marked as approved as per direction of engg-in-

258 4 charge.. (For equipement power)All the switches & Nos 38 810.66 30,805.08 0.00

sockets should be warrantied for a replacement period

of 2 years against defects with ncessary test report &

Warrnaty certificate to be submitted to the department

for genuinity of product & to avail free aftersales service

within warranty period for acceptance of materials.

Supplying,fixing of 1x6A+1X1 6A Plug on the separate

board with complete fitting by 01 no of 16A+1 no 6A

switch & socket(modular type) ( ( flame retradant type)

with suitable size modular box & metallic cover plate

(both side)( falme retradant type)including supplying of

all required accessories of ISI marked as approved as

per direction of engg-in-charge.. (For equipement

power)(Maximum 02 nos point in one circuit).All the

switches & sockets should be warrantied for a

replacement period of 2 years against defects with

ncessary test report & Warrnaty certificate to be

submitted to the department for genuinity of product &

to avail free aftersales service within warranty period

for acceptance of materials.

Supplying,fixing of 3x6A+1X1 6A Plug on the separate

board with complete fitting by 01 no of 16A+3 nos 6A

switch & socket(modular type) ( (flame retradant type)

with suitable size modular box & metallic cover plate

(both side)(anti bactorial & falme retradant

type)including supplying of all required accessories of

ISI marked as approved as per direction of engg-in-

charge. (For equipement power). (Maximum 02 nos

point in one circuit).All the switches & sockets should be

warrantied for a replacement period of 2 years against

defects with ncessary test report & Warrnaty certificate

to be submitted to the department for genuinity of

product & to avail free after sales service within

warranty period for acceptance of materials.

Receass wiring for circuit/submain wiring with the

following mentioned size PVC FRLS insulated, copper

conductor, single core cable in recessed HMS FRLS

PVC conduit of mentioned size as required as per

261 7 direction of Engg.-in-Charge. Mtr 1227.5 187.62 230,303.55 0.00

2 nos single core 1.5 sq. mm copper wire for phase and

neutral and 01 no of single core 1.5 sq. mm copper wire

for earth continuty conductor. In 20 mm dia non

metallic heavy duty conduit (LDB to LSB/LIGHT

Receass wiring for circuit/submain wiring with the

following mentioned size PVC FRLS insulated, copper

conductor, single core cable I in recessed HMS FRLS

PVC conduit of mentioned size as required as per

direction of Engg.-in-Charge.

262 8 2 nos single core 2.5 sq. mm copper wire for phase and Mtr 2838.5 204.14 579,451.39 0.00

neutral and 01 no of single core 1.5 sq. mm copper wire

for earth continuty conductor in 20 mm dia non metallic

heavy duty conduit.(BDB to LSB/LIGHT CKT/5A

PLUG/UPS POINT ) (2X2.5+1X1.5)

Digitally signed by VARUN

Receass wiring for circuit/submain wiring with the

following mentioned size PVC FRLS insulated, copper

conductor, single core cable in recessed HMS FRLS

PVC conduit of mentioned size as required as per

263 9 direction of Engg.-in-Charge. Mtr 1272 225.38 286,683.36 0.00

2 nos single core 4 sq. mm copper wire for phase and

neutral and 01 no of single core 1.5 sq. mm copper wire

for earth continuty conductor in 20 mm dia non metallic

heavy duty conduit .(PDB to PSB/ POWER POINT/AC

POINT) (2X4+1X1.5)

Receass wiring for circuit/submain wiring with the

following mentioned size PVC FRLS insulated, copper

conductor, single core cable in recessed HMS FRLS

PVC conduit of mentioned size as required as per

264 10 direction of Engg.-in-Charge. Mtr 616.5 261.96 161,498.34 0.00

2 nos single core 6 sq. mm copper wire for phase and

neutral and 01 no of single core 2.5 sq. mm copper wire

for earth continuty conductor in 25 mm dia non metallic

heavy duty conduit .(LFDB TO LBDB/UBDB)

Receass wiring for circuit/submain wiring with the

following mentioned size PVC FRLS insulated, copper

conductor, single core cable in recessed HMS FRLS

PVC conduit of mentioned size as required as per

265 11 direction of Engg.-in-Charge. Mtr 616.5 376.42 232,062.93 0.00

4 nos single core 6 sq. mm copper wire for phase and

neutral and 02 nos of single core 4 sq. mm copper wire

for earth continuty conductor in 32 mm dia non

metallic heavy duty conduit.(LFDB TO LBDB/Medical

Receass (4X6+2X4)

wiring for circuit/submain wiring with the

following mentioned size PVC FRLS insulated, copper

conductor, single core cable in recessed HMS FRLS

PVC conduit of mentioned size as required as per

266 12 direction of Engg.-in-Charge. Mtr 616.5 526.28 324,451.62 0.00

4 nos single core 10 sq. mm copper wire for phase

and neutral and 02 nos of single core 6 sq. mm copper

wire for earth continuty conductorin 32 mm dia non

metallic heavy duty conduit .(LFDB TO FLOOR PANEL

Supplying andpower) (4X10+2X6)

installation of 25A AC starter Modular

type, coil voltage-230 Volt A.C. on mod Box of suitable

size including modular coveras required as per direction

of Engg.-in-Charge .All the Components should be

267 13 warrantied for a replacement period of 2 years against Nos 23 739.86 0.00 17,016.78

defects with ncessary test report & Warrnaty certificate

to be submitted to the department for genuinity of

product & to avail free aftersales service within

warranty period for acceptance of materials.

Supply and fixing CALL bell (Ding dong type) /Buzzer

on the existing switch box/cover. .as required as per

direction of Engg.-in-Charge.All the Components should

be warrantied for a replacement period of 2 years

against defects with ncessary test report & Warrnaty mtrs 6 252.52 1,515.12 0.00

certificate to be submitted to the department for

genuinity of product & to avail free aftersales service

within warranty period for acceptance of materials.

S/F of Bakelite angle holder/batten holder reputed

make A catagory ISI marked as approved )of ISI

marked conforming to IS-1258/1987 in place of ceiling

rose as per direction of Engg.-in-Charge .All the

269 15 Components should be warrantied for a replacement each 11 89.68 986.48 0.00

period of 2 years against defects with ncessary test

report & Warrnaty certificate to be submitted to the

department for genuinity of product & to avail free

aftersales service within warranty period for acceptance

270 of materials.

Sub-Head II (Light fitting Fixture & Fan) 0.00

Supplying, installation, of exhaust fan of heavy duty

300 mm sweep 1400 rpm with louvers of exhaust fan

271 16 in the existing wall, including fixing & conntection as Nos 30 3,693.40 0.00 110,802.00

required as per direction of Engg.-in-Charge.

Replacement Warranty will be 2 years.

Supplying, installation, of exhaust fan of heavy duty

380 mm sweep 1400 rpm with louvers of exhaust fan in

272 17 the existing wall, including fixing & conntection .as Nos 14 4,343.58 0.00 60,810.12