PROVISION OF DEFICIENT SINGLE LIVING IN ACCN FOR AIRMEN AND SNCOS UNDER GE AF LEH

Amount

Total amount of Sch 'A' Part-I (Section-I) ( Bldg Work) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only

Design, Fabrication, Erection and construction of building for single living ACCN for ORs and NCs as per architectural Drawings and structural drawings designed by the bidder based on input data as provided in the tender documents and as per specification including as per note given below:- Note:- (A) Super structure in steel strcture as per IS 800 and IS 1893-2016 with limit state method using LGSF member confirming to IS standard with RCC foundation Shallow or deep foundation based on the safe bearing capacity (SBC) of the soil as and the structure load as per design criteria specified. (B) Reinforced Cement Concrete - M-30 Design mix and Reinforcement steel of grade Fe-550 D TMT bars.(c) Floor/ Deck slab shall be of GI profiled sheet of thickness as per design with RCC laid over it. (D) Internal and external walls with LGSF wall of min thickness 140mm alongiwth rock wool of density not less than 48Kg/Cum sandwiched between 12.5mm thick Gypsum board and min 8mm thick fiber cement board on both sides. The external cladding to be of weather proof PPGI sheet of min thick 0.5mm with pre painted camouflage pattern as approved. The bathroom and toilet wall shall be in PCC block as shown in drawing (E) The detail design and construction shall also include design of internal water supply scheme and sanitary plumbing scheme and supply and fixing of fitting and fixture as specified. (F) The design and construction shall cater for provision of services such as internal water supply, sanitary plumbing wks etc. (G) Confirmatory SBC test as per IS provisions (H) Finish of building as per schedule of finish. Any missing details of finish shall be as per manufracturers guideline and as approved by GE.

Design, Fabrication, Erection and construction of building for single living ACCN for Vayuwomen as per architectural Drawings and structural drawings designed by the bidder based on input data as provided in the tender documents and as per specification including as per note given below:- Note:- (A) Super structure in steel strcture as per IS 800 and IS 1893-2016 with limit state method using LGSF member confirming to IS standard with RCC foundation Shallow or deep foundation based on the safe bearing capacity (SBC) of the soil as and the structure load as per design criteria specified. (B) Reinforced Cement Concrete - M-30 Design mix and Reinforcement steel of grade Fe-550 D TMT bars.(c) Floor/ Deck slab shall be of GI profiled sheet of thickness as per design with RCC laid over it. (D) Internal and external walls with LGSF wall of min thickness 140mm alongiwth rock wool of density not less than 48Kg/Cum sandwiched between 12.5mm thick Gypsum board and min 8mm thick fiber cement board on both sides. The external cladding to be of weather proof PPGI sheet of min thick 0.5mm with pre painted camouflage pattern as approved. The bathroom and toilet wall shall be in PCC block as shown in drawing (E) The detail design and construction shall also include design of internal water supply scheme and sanitary plumbing scheme and supply and fixing of fitting and fixture as specified. (F) The design and construction shall cater for provision of services such as internal water supply, sanitary plumbing wks etc. (G) Confirmatory SBC test as per IS provisions (H) Finish of building as per schedule of finish. Any missing details of finish shall be as per manufracturers guideline and as approved by GE.

Design, Fabrication, Erection and construction of building for Plant room as per architectural Drawings and structural drawings designed by the bidder based on input data as provided in the tender documents and as per specification including as per note given below:- Note:- (A) Super structure in steel strcture as per IS 800 and IS 1893-2016 with limit state method using LGSF member confirming to IS standard with RCC foundation Shallow or deep foundation based on the safe bearing capacity (SBC) of the soil as and the structure load as per design criteria specified. (B) Reinforced Cement Concrete - M-30 Design mix and Reinforcement steel of grade Fe-550 D TMT bars.(c) Floor/ Deck slab shall be of GI profiled sheet of thickness as per design with RCC laid over it. (D) Internal and external walls with LGSF wall of min thickness 140mm alongiwth rock wool of density not less than 48Kg/Cum sandwiched between 12.5mm thick Gypsum board and min 8mm thick fiber cement board on both sides. The external cladding to be of weather proof PPGI sheet of min thick 0.5mm with pre painted camouflage pattern as approved. The bathroom and toilet wall shall be in PCC block as shown in drawing . (E) The detail design and construction shall also include design of internal water supply scheme and sanitary plumbing scheme and supply and fixing of fitting and fixture as specified. (F) The design and construction shall cater for provision of services such as internal water supply, sanitary plumbing wks etc.(G) Confirmatory SBC test as per IS provisions (H) Finish of building as per schedule of finish. Any missing details of finish shall be as per manufracturers guideline and as approved by GE.

Design, Fabrication Erection and construction of Over Head water tank of capacity 50000 Litre with staging at 12 Meter. The tank shall be made of GRP panel as per IS 14399 Part- I & II. It should be corrosion resistent chemical resistent, electrical resistent UV stability, light weight higher strength to wieght ratio, fire retardent and tailor made, the bottom and side of panel made of concave shape, panel shoud have following properties : (A) Tensile strength should be minmum 70 MPA (B) bending strength should be minimum 100 MPA (C) Elastic modulus in bend should be minimum 6000 MPA (d) glass contain (%) maximum 0.5 %. The staging shall be structural steel as per IS 800 design with limit state method with RCC in M-30 design Mix concrete and reinforced steel confirming to Fe 500 D/ Fe 550 D TMT complete all as specified and as directed by Engr-in-charge

Total amount of Schedule 'A' PART-I (BUILDING WORK)

Total amount of Sch 'A' PART-II ( SITE CLEARANCE)

Total amount of Sch 'A' PART-III (SEC-I) (INTERNAL ELECTRIC SUPPLY)

Total amount of Sch 'A' Part-III (Section-II) (INTERNAL ELECTRIFICATION) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only

Supply & Fixing Vertical triple phase & neutral Distribution box double door type ,as per IEC 61439-3 made of sheet metal enclosure dust proof vermin proof suitable for flush mounting and surface mounting with 250A Copper Busbar for each phase,415 volts with in built MCCB 125 Amps, 25KA, 2 Neutral bar,2 Earthbar IP- 54 Protection and cable ties for cable management,fully insulated busbar & shrouded Neutral bars, reversible door for IP 43 & IP54 DB's, flush mounted to wall complete all as specified and as directed by Engr-in-charge. Note:- Rate are inclusive of Flush(concealed) Mounting of DB and MCCB 125Amps

Supply & fixing recessed mounted LED luminaire of capacity 18W, 240V, 50Hz down light with white colour injection moulded body made up of polycarbonate,high transmittvity Diffuser specially designed,each to install mounted clips,slim with backlit technology, driver and accessories prewired less power consumption with colour temperature not less than 6500K , ingress protection IP-20 ambient temperature 0-450C, power factor more than 0.95, surge protection 2.5KV, multistage isolated constant current, voltage operated driver with range 150-270V, AC single phase,long life 50,000 burning hours as per L70B50,Suitable for Armstrong / CRG/TRAC / USG / Celotex / POP modular ceiling system,complete all as specified and as directed by Engr-in-charge

Supply & Fixing 12 watt Dexter rotatable reading bedside LED enegy efficient wall light having comfortable color temperature, made of brushed Gold,brushed black,electroplating or powder coating. fitting has light colour of 3 type i.e Warm White,Natural White and Cold White it has push button switch for on/off and dimension of fitting is 16cmx18cmX9.5 cm, complete all as specified and as directed by Engr-in-charge.

Supply & Fixing for LED Building security Light fitting 25 watt, for opearting voltage between 110V to 320V system efficiency not less than 120 lumen / watt, PF-0.95 minimum, IP66 protection, 5700CCT(K), CRI between 80-85, confirming to LM79 and LM 80 standards or as per IS-16104:2012 and IS-16106:2012, for estimated life span of minimum 50,000 hrs consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with LED street optics LENS for uniform light distribution, weather proof gasket for lamp & driver compartment, Heat resistance toughened UV stabilized glass fitted in cast aluminium housing with SS screws including Bracket made out of GI light grade pipe of size upto 40 mm dia suitable for fixing with LED building security light, 1.5 mtr long bend to an angle of 120 degree with 02 Nos MS clamp 50mm x 50mm and 04 sets of nuts, bolts and washers painting with two coats of synthetic enamel paint over a red oxide primer complete all as specified and as directed by Engr-in-charge

Supply and fixing MCB Single Pole 2 Amps rating 240V, 10KA 'C' curve miniature circuit breaker complete with connection testing and commissioning complete all as specified.

Supply and fixing MCB Single Pole 6 Amps rating 240V, 10KA 'C' curve miniature circuit breaker complete with connection testing and commissioning complete all as specified.

Supply and fixing MCB Single Pole 16 Amps rating 240V, 10KA 'C' curve miniature circuit breaker complete with connection testing and commissioning complete all as specified.

Supply and fixing MCB Double Pole 32 to 40 Amps rating 240V, 10KA 'C' curve miniature circuit breaker complete with connection testing and commissioning complete all as specified.

Total amount of Sch 'A' Part-III (Section-II) (INTERNAL ELECTRIFICATION)

Total amount of Sch 'A' PART-IV (SEC-I) ( ROAD WORK)

Total amount of Sch 'A' PART-IV (SEC-II) ( PCC PATH WORK)

Total amount of Sch 'A' PART-V (SEC-I) (EXTERNAL WATER SUPPLY)

Total amount of Sch 'A' Part-V (Section-II) (EXTERNAL WATER SUPPLY) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only

S & F cast iron air release valves with double air outlets, conforming to IS 14845 of size 50 mm dia ISI marked bore and fixing up in cast iron water supply mains of size 50mm dia complete all as specified and as directed by Engr-in-charge

Material and labour for construction of valve chamber of size 1.2mx 1.2m x1.2m (LxBxH) with the following specifications:- (i) Excavation and earth worki in any type of soil. (ii) PCC 1:4:8 type D2 for foundation (using 40mm graded stone aggregate) 150 mm thick. (iii) chamber valve shall be 200 mm thick block masonry PCC (1:3:6) ( using 20mm graded stone aggregate) set in cm (m 1:6) (iv) Internal and exposed surfaces of valve chamber shall be plastered with 15 mm thick cement plaster in cm (1:4). (v) 50 mm thick coping in PCC 1:2:4 ( using 20mm aggregate)shall be provided over wall of valve chamber. (vi) The precast surface will be provided with coats of white wash. (vii) All steel surfaces will be provided with two coats of synthetic enamel panit of first qualtity over coat of red oxide zinc -chrome primer prior to prepration of surface. (viii) All the excavated earth obtained from excavatioin shall be disposed off from the site of work. (ix) The Chamber shall be provided MS angle iron structure 1.2m x1.2m x 1.2m of size 50mm x50mm at the depth of the valves along with puff panel cover 100mm thick provided with lifting handle. The cover shall be provided with opertaing holes to operate the sluice valves with markings of locations over the holes to identify the valves. (x) Top cover the valve pit shall be provided with precast RCC cover with minimum 80 mm thickness provided over the angle iron frame. (xi) Steel surface shall be painted with two coats of synthetic paint over the coat of red oxide primer complete all as specified and as directed by Engr-in-charge.

Total amount of Schedule 'A'Sch 'A' Part-V (Section-II) (EXTERNAL WATER SUPPLY)

Total amount of Sch 'A' PART-VI (SEC-I) (HOT WATER SUPPLY)

Total amount of Sch 'A' Part-VI (Section-II) (HOT WATER SUPPLY) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only

Supply, fixing, commissioning and testing of hot water generator capable of delivering a heat output 50,000 KCal/Hr using HSD oil with out let temp 90-95 degree celcius and efficiency more than 90% , Horizontal (skid mounted), smoke tube, reverse flame with minimum 03 Nos of passes with flow rate of 2500 LPH, working pressure 6 Kg/cm2. The inner shall be made of carbon steel and outer shell shall be made of Mild steel, front and back door shall be lined with high grade insulation and refractory, Pressure relief valve, in/out pressure gauge with ball valve, Inlet and Outlet temperature controller, Pressure Switch, Water and high temperature cut out, Hour-meter complete in all respect, including following item of work: (a) Heater unit : Heat exchanger horizontal (skid mounted), smoke tube, reverse flame, consisting of closely wound, helical, concentric coils, arranged to give 03 No of passes on flue gas and made of carbon steel confirming to BS 3059, PART-I, ST 320, ERW), suitable for high temperature all as per manufactures design. (b) Pressure jet burner : Highly efficient with low noice, Suitable for light oil/HSD firing with stepless modulation mechansim all as per manufactures design and of required head and capacity. (c) Combusion air fan with drive motor assembly all as per manufactures design and of required capacity. (d) Control Panel: Dust protected control panel made of 2 mm thick CRCA sheet finished with baked enamel paint, prewired with main incommer, indicator lights, hours meter, relay, fault indicating lights such as high temp of water, burner trip at high temprature of flue gasses with audio alarm , burner management system, switchgear consisting of contractor overload relays, fuses and MCBs etc, all as per manufactures desig and of required capacity. (e) Circulating pumps. Centrifugal water circulating pumps suitable for high temperature operation coupled with electric motor drive, mounted on common base frame all as per manufactures design and of required head and capacity. ( Capacity of pump should not be less than 2 HP ) (f) Fuel Pump: Fuel pump with drive motor assembly all as per manufactures design and of required head and capacity.

Supply & fixing Chimney for exhaust of burnt smoke of minimum diameter 100mm dia and length 8 meter , fabricated of B class MS Black pipe conforming to IS 1239 ( Part-I) including canopy at the outlet of the chimney, flange to fix the chimney with the space heater complete all as specified and as directed by Engr-in-charge

Supply and installation of Diesel fuel storage tank of capacity 500 litre made out of 5mm thick MS sheet complete with supply arrangement for topping up of service tank including lifting pump set suitable, control/drain valves complete, complete all as specified and as directed by Engr-in-charge.

Supply and installed water Pumping sets, 3 HP ( 1.5 KW) centrifugal, electric driven, 3 phase, 415 volts ISI marked of suction x delivery (65mmx50mm) , 2900 RPM Head minimum 20 mtrs and discharge minimum 250 LPM complete including electrical connections, vibration paddings & PCC foundation including grouting of bolts of suitable length all as per manufacturer recommendation and as specificed and directed.

Design and installation for cold Water storage tank of capacity 7000 Litre, fabricated out of 10mm thick MS sheet/plate for shell and end plate complete with inlet cold water from water supply installation flanges welded at proper places to suit equipment/system feeding system and man hole of 600mm dia with neck raised to 200 mm and provided with welded MS flange 10mm thick with drilled holes and top lid of 10 mm thick with hole nuts, bolts washers and 6mm thick gasket, pa inted with 2 coats of anticorrosive paint over a coat of red exide including provision of PUF Insulatiopn of 50 mm thick with 40kg/m3 density including 26 SWG plain Aluminium cladding for steel tank complete all as specified and as directed by Engr-in-charge

S & F cast iron air release valves with double air outlet conforming to IS-14845 of size 50mm dia ISI marked and fixed in galvanized iron water supply main of size 50 mm dia including cutting, welding. Provn of flanges, gaskets, nuts, bolts, washers etc all as specified and directed by Engr-in-charge

S & F CI valve reflux with by pass arrangement, conforming to IS-14845 of size 50mm dia, flanged end type, ISI marked including provision of rubber gaskets, nuts, bolts, washers etc all as specified and directed by Engr-in-charge

S & F Y-strainer SS conforming to IS-12785 (1994) , size 50mm ( 2") dia ISI marked complete all as specified and as directed by Engr-in-charge

Total amount of Schedule 'A'Sch 'A'Sch 'A' Part-VI (Section-II) (HOT WATER SUPPLY)

Total amount of Sch 'A' PART-VII (SEC-I) (EXTERNAL ELECTRIC SUPPLY)

Total amount of Sch 'A' PART-VII (SEC-II) (EXTERNAL ELECTRIC SUPPLY) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only

material & labour for Construction of Platform of overall size of 3000mm x 2500mm x 1200mm with PCC 1:4:8 type D-2 (with 40 mm graded crushed stone agrregate), 15 mm thick in foundation, brick work in CM 1:6 with sub class "B" old size brick, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) on top and grouting bolts etc with fencing foldable upto 1.5m height, gate with locking arrangements using GI wire mesh, GI wire 4mm dia, angle iron, MS plate etc, complete all as specified and shown in drawing No. CEPZ/ TD-350/08 sheet 1/2 & 2/2 dated 14 Nov 2008 and as directed by Engr-in-charge

S & F cable route indicator at the distance of 50 meter each made out of 45mm x 45mm x 5 mm angle iron, 80 mm long embedded in PCC block of suitable size with moulded lettter HT CABLE or LT CABLE suitably incribed on CI circular plate 8 mm thick 100 dia including painting with two coats of synthetic enamelled paint over a coat of red oxide primer including neccessary PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggrregate) block of suitable size and neccessary earth work and excavation complete all as specified and as directed by Engr-in-charge

(d) Timer switch along with 415 V three Phase contactors 25 Amp rating and MCB 4 Pole 415 V, 25 Amps as incoming and one MCB 4 Pole 415 V, 20 Amps as outgoing incl copper cable for connection and fixing complete all as specified and directed (e) All accessories prewired with suitable size copper wire with stand high temperature, housed in cubical panel made out of standard MS sheet factory made duly powder coated front and rear door open able with locking arrangement complete with foundation as required or recommended by manufacturer. NOTE :Main Aluminum busbars with 0.8Amps/sqmm current density & all internal wiring with copper FRLS wires and connections. All MCCB's are Microprocessor/Thermal Magnetic based (Icu = Ics = 100%) as given in sld, housed in separate compartments, enclosed on sides, with rotating handle. All MCB Icu=10kA where not given/mentioned.Earthing all components, frame etc. to a common internal earth bar.Painting all sheet metal works support structure etc.All accessories & supporting structure (Hot Dip Galvanised).The panel shall be with Galvanized MS mounting base frame & the height shall not exceed more than 2100mm. The panel shall be prewired, ready for External Cable termination.All Gland Plate's shall be 3 mm thick removable type.All the CT's shall be cast resin type, with necessary CT shorting link.The panel shall be in convenient sections suitable for transportation, erection & have sufficient space for Incoming & Outgoing cable terminations. The panel Incomers/Outgoings shall have Potential free Contact.3 mm thick acrylic sheet shall be provided on the top of all outgoing termination sections, for protection against live terminals. All the panel Incomers & Outgoings shall be tagged with aluminum anodized engraved name plates (Detailed tag of the feeders will be given during the final approval of panel drawings) Vendor shall arrange to configure / check / set all the meters once the panel is completely installed & in operation at site.

Material & Labour for LT Cable junction box outdoor shall be made out of Polycarbonate with glass fiber reinforced of size 205mm x 255mm x 112 mm (the cable size upto 25 sqmm). The polycarbonate junction box shall be environmental friendly, recyclable, halogen & silicon free, anti acid & anti corrosive. The Junction Box shall be rated for Degree of ingress Protection IP 66 in accordance with IEC 60529.Weatherproof, UV resistant. The gasket material of junction box shall be Polyurethane and the gasket shall be internally embedded. The Junction Box shall be complies with requirements of the standards IEC 60998. The Junction Box with 25Amp Connectors or Terminal Trip or Bus Bar. The Junction Box / Enclosure shall be tested as per IEC including one No. 4 pole connector and chromium plated clamps and nut bolts, cable glands with lock nuts of 2 Nos for each box all as per manufacturer’s instructions and specifications complete all as specified and directed by Engineer-in-charge.

Supply & Fixing Bracket made out of GI light grade pipe of size upto 40 mm dia, suitable for fixing street light 1.5 mtr long bend to an angle of 120 degree with 02 Nos MS clamp 50mm x 50mm and 04 sets of nuts,bolts and washers painting with two coats of synthetic enamel paint over a red oxide primer including making provision of fixing security light with bracket as per the size of mounting bracket of security light complete all as specified and as directed by Engr-in-charge

Total amount of Sch 'A' PART-VII (SEC-II) (EXTERNAL ELECTRIC SUPPLY)

Total amount of Sch 'A' PART-VIII (SEC-I) (SEWAGE DISPOSAL)

Total amount of Sch 'A' PART-VIII (SEC-II) (SEWAGE DISPOSAL ) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only

Material and labour for RCC Septic tank designed to carry sewage and sullage water and shall comprises of activities like excavation in any type of soil, PCC (1:4:8) type D2 (using 40mm graded crushed stone aggregate) below foundation, RCC M-30 Design Mix in Walls , Base Slab , Baffle walls and Roof Slab including beams etc with Vent shaft, manhole openings with cover connection etc., complete with effective depth of 1.5 meter and overall depth of 3 meter for 150 Users, complete all as specified and shown on drawing including as directed by Engr-in-Charge

Material and labour for Construction of Soakage well, of size 3Meter dia X 4.5Meter effective depth made out of stone masonry construction, complete all as specified and shown on drawing including as directed by Engr-in-Charge

Total amount of Sch 'A' PART-VIII (SEC-II) (SEWAGE DISPOSAL )

M M SHAWL Engineers and contractors pvt ltd (BID ID -3269852)

M/S ANIL KUMAR (BID ID -3267153)

DES RAJ AND SONS BUILDERS PVT LTD (BID ID -3269394)

SHIV CHARAN GUPTA AND SONS (BID ID -3274499)