CONSTRUCTION OF CSC NEAR JAMIA MASJID KALATOO,MAHAKUND

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed in all kinds of soils.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size).

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) with 30% boulders

Providing and laying in position stone Boulders of small size including all etc. complete

Brickworkwith common burnt clay bricks of class designation 75 in cement moratr 1:6 (1 cement: 6 coarse sand) in foundation and plinth

Providing and laying in position Reinforced cement concrete in beams, cantilevers, suspended floors, roofs etc. etc. all work above plinth upto floor V level of specified grade including curing but excluding the cost of centring and shuttering in 1:1.5:3 (1 cement :1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Steel Reinforcement for RCC work including cutting, bending, binding and placing in position all complete (TMT bars of Fe500 Grade)

Centering and shuttering including strutting, propping etc. and removal of form work for:foundations ,footings bases, roofs, walls, floors etc.

Centering and shuttering including strutting, propping etc. and removal of form work for:suspended floors, roofs etc.

Centering and shuttering including strutting, propping etc. and removal of form work for:Edges of Slabs etc

Providing and fixing angle iron frames for doors, windows, ventilators of mild steel angle section of size 35x35x5mm welded by angle iron 35x35x5mm or 35x5mm flat pieces to the existing T iron frame including necessary fittings with a priming coat as per the directions of Engineer Incharge

Providing and fixing 1mm thick MS sheet door with frames of 40x40x6mm angle iron and 3mm MS gusset plates at junctions and corners including necessary fittings with a priming coat as per the directions of Engineer Incharge

Providing and fixing Glass panes with putty and glazing clamps in steel doors, windows, ventilators etc. including necessary fittings with 4mm thick glasss panes.

40mm thick Cement Concrete Flooring 1:2:4 (1 Cement:2 Coarse Sand:4 Aggregates) finished with a floating coat of neat cement including cement slurry and curring complete.

Providing and fixing 1st quality Ceramic Glazed Wall/Floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:3 (1cement :3 coarse sand) including grouting the joints with white cement and matching pigments.

15mm thick cement plaster of mix 1:4 (1 cement: 4 fine sand)

Painting with Synthetic enemal paint of approved brand and manufacture two or more coats.

Distempering with oil bound distemper of approved brand and manufacturer to give an even shade on new work (two or more coats) over and including priming coat with water thinable cement primer

Providing and fixing G.I pipes complete with G.I. fittings and clamps including cutting and making the good the walls etc concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the walls: 15mm dia nominal pipe

Providing and fixing G.I pipes complete with G.I. fittings and clamps including cutting and making the good the walls etc concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the walls: 20mm dia nominal pipe

Providing and fixing PTMT Bib cock of approved quality and colour 15mm nominal bore 95mm long weighing not less than 88gms (Long Body)

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and placing on terrace (at all floors) polyethylene waterstoragetank ISI:12701 marked of 1000ltrs capacity water tank including making the inlet/outlet/overflow holes and suitable locking arrangment as per the directions of the Engineer-In-charge with all fittings complete

Providing and fixing PVC pipe 2.5 inch dia superior quality

Providing and fixing PVC pipe 4.0 inch dia superior quality

Providing and fixing 4.0 inch dia PVC bend

Providing and fixing 2.5 inch dia PVC bend

Providing and fixing 4.0 inch dia P-Trap

Providing and fixing 15mm dia G.I elbow

Providing and fixing 15mm dia G.I socket

Providing and fixing 3/4 inch x 1/2 inch Tee

Providing and fixing 3/4 inch Union

Providing and fixing Nipples of different dias

Providing and fixing 1/2 inch Union

Carriage of Steel/Cement from source to site by mechanical transport or animal transport or by head load

Carriage of Sand from source to site by mechanical transport or animal transport or by head load

Carriage of Aggregates from source to site by mechanical transport or animal transport or by head load

Carriage of Stones from source to site by mechanical transport or animal transport or by head load

Carriage of Bricks from source to site by mechanical transport or animal transport or by head load

Providing/Fixing of Citizen information board (complete job)

Please Enable Macros to View BoQ information