NIT-08

Amount

SCHEDULE 'A' PART-I : BOQ OF WORKS FOR B/R WORKS.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and as directed by Engineer-In-Charge.

Providing and fixing everest board 4mm thick, designer, in ceiling fixed as per manufacturer’s instructions, including powder coated galvanised iron snap grid frame work of main and tee (weight not less than 240gm/Rm), angle (weight not less than 217 gm/Rm), grid size 595x595mm, for false ceiling all as specified, and hangers 6mm dia, galvanised iron (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of galvanised iron wire of 4.0mm dia, length as required at site and expansion hold fasteners 12.50mm dia, 40mm long, complete all as specified and as directed by Engineer-In-Charge.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-In-Charge.

Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and as directed by Engineer-In-Charge.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and as directed by Engineer-In-Charge.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and as directed by Engineer-In-Charge.

Rendering 15mm thick, on fair faces of brick or concrete surfaces, in cement mortar 1:6, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-In-Charge.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion over one coat of chalk whiting, on plastered surfaces, preparatory to distempering, complete all as specified and as directed by Engineer-In-Charge.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement paint over one coat lime wash, complete all as specified and as directed by Engineer-In-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed by Engineer-In-Charge.

Non-skid, coloured, ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including laid over screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and as directed by Engineer-In-Charge.

Glazed ceramic tiles in vertical surface/ dado, size 300x450x7mm thick, 400x400x6/7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match, the shade/ colour of tiles including 10mm thick rendering in cement mortar 1:4, complete all as specified and as directed by Engineer-In-Charge.

Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm each, complete all as specified and as directed by Engineer-In-Charge.

Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exceeding 4.0 Sqm each, complete all as specified and as directed by Engineer-In-Charge.

Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 125x60mm, complete all as specified and as directed by Engineer-In-Charge.

Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 105x60mm, complete all as specified and as directed by Engineer-In-Charge.

Factory made, glazed and skeleton shutters in second class hardwood, 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and as directed by Engineer-In-Charge.

Factory made, 35mm thick, second class hardwood, plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and as directed by Engineer-In-Charge.

Preparation of new or previously untreated wood or wooden surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed by Engineer-In-Charge.

Factory Made Solid PVC Moulded Door Shutter, 30mm thick (stiles), with 2, 4, or 6 raised panel design 2mm thick Moulded Prelam PVC Sheet on the front face and 2mm Plain colour PVC Sheet on back face, supplying and fixing in frame at site as per specification, supplying and fixing in the frame with three Nos of powder coated stainless butt hinges of 100mm size and rust proof screws, at site as per specification and drawing, complete all as specified and as directed by Engineer-In-Charge.

Butt hinges, size 100mm, medium weight, cold rolled mild steel, and fixed, complete all as specified and as directed by Engineer-In-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/ steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed by Engineer-In-Charge.

Sheet glass, 3.0mm thick, ordinary quality and glazing with oil putty or with wooden beadings, fixing in square not exceeding 0.50Sqm in each pane, complete all as specified and as directed by Engineer-In-Charge.

Aluminium handles, cast type, anodised, size 150mm, complete all as specified and as directed by Engineer-In-Charge.

Aluminium handles, cast type, anodised, size 150mm, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Aluminium anodised, barrel tower bolts of extruded Section, size 150mm long and fixed, complete all as specified and as directed by Engineer-In-Charge.

Aluminium anodised, barrel tower bolts of extruded Section, size 200mm long and fixed, complete all as specified and as directed by Engineer-In-Charge.

Aluminium alloy, anodised, sliding door bolt, size 300mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed by Engineer-In-Charge.

Aluminium alloy, anodised, sliding door bolt, size 250mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Aluminium alloy, anodised, sliding door bolt, size 300mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, cverall length of cover plate 140mm, fixed in floor, complete all as specified and as directed by Engineer-In-Charge.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, cverall length of cover plate 140mm, fixed in floor, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Mild steel spring for doors, 300mm, ordinary rat tail rod pattern springs including roller and roller plate, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed by Engineer-In-Charge.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, fixed in repairs, complete all as specified and as directed by Engineer-In-Charge.

Resecuring or easing and adjusting with out taking down shutters of any descriptions, area exceeding 1.00 Sqm but not exceeding 2.00 Sqm and re-fixing in the same openning, complete all as specified and as directed by Engineer-In-Charge.

Mild steel spring for doors, 300mm, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and as directed by Engineer-In-Charge.

Resecuring or easing and adjusting with out taking down shutters of any descriptions, area not exceeding 1.00 Sqm re-fixing in the same openning, complete all as specified and as directed by Engineer-In-Charge.

Taking up or down steel tubing of 15mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed by Engineer-In-Charge.

Tubes, 'medium grade' galvanised, 15mm bore, ISI marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed. Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates.

Old tubes, 'any grade' galvanised, 15mm bore, with all new fittings such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-In-Charge. Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates.

Taking up or down steel tubing of 20mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed by Engineer-In-Charge.

Tubes, 'medium grade' galvanised, 20mm bore, ISI marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed. Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates.

Old tubes, 'any grade' galvanised, 20mm bore, with all new fittings such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-In-Charge. Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates.

PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, capacity 10.0 litres and making good to dismantled/ damaged floor/ surfaces, fixing in repair, complete all as specified and as directed by Engineer-In-Charge.

Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern, complete all as specified and as directed by Engineer-In-Charge.

PVC connections 15mm size with brass nuts of length 450mm, complete all as specified and as directed by Engineer-In-Charge.

Bib taps, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Bib tap, long body, standard of PTMT any colour high pressure screwed for iron pipe and fixed for 15mm bore pirpe, (Minimum weight 15mm-120gms), fixing in repairs, complete all as specified and a sdirected by Engineer-In-Charge.

Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed for 15mm bore iron pipe (Minimum weight 15mm-90gms), fixing in repairs, complete all specified and as directed by Engineer-In-Charge.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed for 15mm bore pipe, fixed in repair, complete all as specified and as directed by Engineer-In-Charge.

Angle valve/ cock, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Angle stop valve of PTMT any colour, with long shank and cup (concealed type), high pressure screwed for iron pipe and fixed for 15mm bore pipe, (Minimum weight 15mm-110gms), fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Chromium plated PTMT shower rose 150mm square size, fancy type, fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Low density polyethylene (LDPE) pipes of pressure rating 6.0 kgf/Sqcm, 32mm bore and 900mm long, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Tubular towel rail, 20mm dia, D-type, 60cm long between flanges, brass chromium plated, fancy type, including end brackets, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Tubular towel ring 20mm dia, brass chromium plated, universal type, including end brackets, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Rotational moulded polyethylene water storage tanks of 1000 liters capacity, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-in-Charge.

PVC valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mmbore pipe, fixing in repairs, complete all as specified and as directed by Engineer-in-Charge.

Rotational moulded polyethylene water storage tanks of 500 liters capacity, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-in-Charge.

PVC valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 15mmbore pipe, fixing in repairs, complete all as specified and as directed by Engineer-in-Charge.

Waste coupling of PTMT (half or full threaded) for 32mm bore/ dia of discharge pipe, complete all as specified and as directed by Engineer-In-Charge.

PVC (SWR) pipes, 75mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-In-Charge.

Solid stainless steel hat and coat hooks, solid body, 175mm to 250 mm including screws of same metal, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Glass corner shelf, made with 6 to 8mm thick transparent glass, three teirs including anti rust screws, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Hand shower (Health faucet), ABS body with 8mm dia and 1.0mtrs long SS braided flexible tube with wall hook, complete all as specified and as directed by Engineer-In-Charge. Make: Cera cat part No-F8030102 or equivalent in Orient/ Jaquar/ Riviera.

Soap dish, fancy type, fixed to plugs with chromium plated brass screws, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Toilet paper holder, fancy type and chromium plated, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Stainlees steel grating, chromium plated, size 125mm, heavy duty, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Water storage tank lid, PVC lid , suitable for rotational moulded polyethylene water storage tanks of 500/ 1000 liters capacity, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Sheet glass shelf assembly, consisting 5.50mm thick sheet glass, 120mm wide including anti rust screws, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Door seal metallic, powder coated, at least 25mm in wide and 1.0mtr in length with nylon fibre brussels, complete all as specified and as directed by Engineer-In-Charge.

Anodised aluminium powder coated (minimum thickness of powder coating 50micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and as directed by Engineer-In-Charge.

Anodised aluminium powder coated (minimum thickness of powder coating 50micron) door/ window shutters, aluminium section weighing 0.55 Kg/mtr including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc and fixing 5.50mm thick plain glass sheet with rubber packing/ beading, complete all as specified and as directed by Engineer-In-Charge. Note : Cost of Glass and other filling material in panels shall be deemed included in quoted rate.

Anodised aluminium powder coated (minimum thickness of powder coating 50micron) sliding door shutters with frame section size 65mmx37mmx1.50mm with door handle locking system (Godrej/ Link/ Harrison), shutters frame weighing 0.55 Kg/mtr including necessary joining cleats, glazing clips, ruber neoprene packing, 150mm long handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc and fixing 5.50mm thick plain glass sheet with rubber packing/ beading, complete all as specified and as directed by Engineer-In-Charge. Note : Cost of door frame, shutter, glass and other filling material in panels shall be deemed included in quoted rate.

Anodised aluminium powder coated grills of any size, pattern and any aperture, complete all as specified and as directed by Engineer-In-Charge. Note: Weight of grill per square meter shall be decided by BOO for payments.

Door closer, aluminium extruded body section, hydraulically regulated, designation No-01, universal type, suitable for door shutters up to 700mm in width and of weight not more than 35 kg and fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Curtain rod, 20mm dia, mild steel, fancy type, any colour coated with fixing and inlcuing end knobs, fixing brackets, stops, round rings to hold the curtain, fixing in repairs with wall plugs and screws, complete all as specified and as directed by Engineer-In-Charge.

Mild steel flat clamps, colour coated decorative types, made to shape to hold the curtain rods with wall plugs and screws, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

PTMT end knobs, colour coated decorative types, suitable for curtain rod's ends, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Disconnecting existing tank, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in same position after cleaning of water storage tank capacity 500 Ltrs, mounted on any locations including removal of mud and dirts outside from residential area, including writing date of cleaning on outer surfaces with white synthetic enamel paint, complete all as specified and as directed by Engineer-In-Charge. Note: (i) Contractor will submit duly signed user's completion certificate with building details countersigned by Engineer-In-Charge, for each tank before payments. (ii) Cost of all required tools, plants and labours shall be deemed included in quoted rate.

Disconnecting existing tank, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in same position after cleaning of water storage tank capacity 1000 Ltrs, mounted on any locations including removal of mud and dirts outside from residential area, including writing date of cleaning on outer surfaces with white synthetic enamel paint, complete all as specified and as directed by Engineer-In-Charge. Note: (i) Contractor will submit duly signed user's completion certificate with building details countersigned by Engineer-In-Charge, for each tank before payments. (ii) Cost of all required tools, plants and labours shall be deemed included in quoted rate.

Mild steel handle for steel windows of any type, size 100mm, including fixing with welding/ rebating at site, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Mild steel stay arm for steel windows of any type, including fixing with welding/ rebating at site, complete all as specified and as directed by Engineer-In-Charge.

Amount of Schedule of credit of for Rs 18,171.00 shall be deducted from quoted amount.

CHOPRA CONSTRUCTIONS

M/s Vishwakarma Enterprises