REPAIR OF WOODEN FURNITURE AND RECANNING OF CHAIRS ISSUED TO OTM MD ACCN UNDER GE EAST LUCKNOW

Amount

BED PLY TOP (FD-246/ 247)

S&F12mm thick plywood BWR Grade, approved quality in single piece as per drawing without any joint to the bed frame with suitable screws wood/ steel with cup washer including removal of damaged ply wood all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to 1st quality teak wood long rail as per existing size of Bed including removal of damaged long rail all as specified on drawing or as directed by Engineer-in-charge.(Each long rail will be measured as single unit)

All as per item No. 1.02, but short rail all as specified on drawing or as directed by Engineer-in-charge. (Each short rail will be measured as single unit)

S&F in reapirs to head board consisting of 60 x 30 x 260mm vertical size and 30 x 60 x 400mm horizontal including legs of size 60 x 60mm in section at top and length 400mm from bottom of leg and 30 x 30mm in section at bottom complete including removal of damaged head board all as specified on drawing or as directed by Engineer-in-charge.

All as per item No. 1.04, but foot board consisting of 22 x 75mm in section teak battens 3 Nos at equal space, joining top and bottom horizontal rails of foot board. The top and bottom horizontal rails of size 30 x 60mm shall be 1st quality of teak wood. The vertical legs above horizontal rails shall be 30 x 60mm all as specified on drawing or as directed by Engineer-in-charge.

S&F in reapirs to new 1st quality teak wood stiffeners of size 40 x 60mm complete including removal of damaged stiffiners all as specified on drawing or as directed by Engineer-in-charge.

S&F in reapirs to 4mm thick OST plywood commercial of size 780 x 340mm including 12mm dia half round teak wood beading of both side of head board including removal of damaged ply all as specified on drawing or as directed by Engineer-in-charge.

S&F in reapirs to 4mm thick OST plywood commercial of size 780 x 180mm including 12mm dia half round teak wood beading of both side of foot board including removal of damaged ply all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to flat iron of mild steel of size 35mm x 5mm, bents to right angle on each corners of Bed ply top all as specified on drawing or as directed by Engineer-in-charge.

Chair dining (FD-228, FD-279 or Similar)

Removing the existing unserviceable rear leg and providing with new teak wood rear leg complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new teak wood front leg complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable back rest and providing new teak wood back rest slightly curved complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new teak wood front rail drilling holes at 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable rear rail providng new teak wood rear rail including drilling holes at 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable side rails and providing new teak wood side rails including drilling holes at 12.5mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Recaning of repaired chair dining with approved plastic cane 1.80 x0.46mm and border with 3x0.60mm cane of white or cream ivory all as specified on drawing or as directed by Engineer-in-charge.

Chair writing (FD-202, FD-250, FD-280 or similar)

Removing the existing unserviceable rear leg and providing with new teak wood rear leg complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new teak wood front leg complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable back rest and providing new teak wood back rest slightly curved complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new teak wood front rail drilling holes at 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable rear rail providng new teak wood rear rail including drilling holes at 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable side rails and providing new teak wood side rails including drilling holes at 12.5mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable broken arm rest and providing new teak wood arm rest complete all as specified on drawing or as directed by Engineer-in-charge.

Recaning of repaired chair writing with approved plastic cane 1.80 x0.46mm cane and border with 3x0.60mm cane of white or cream/ivory all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge.

CHAIR EASY (FD-203,FD-229 or similar)

Removing the existing unserviceable rear leg and providing with new teak wood rear leg complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new teak wood front leg complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable broken arm rest and providing new teak wood arm rest complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front frame and providing new teak wood front frame including drilling holes @ 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front/back rail and providing new teak wood front rail complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable side rails and providing new teak wood side rails complete all as specified on drawing or as directed by Engineer-in-charge.

Recaning of repaired chair easy seat and back of approved quality white or cream ivory with 1.80 x 0.46 mm cane and border with 3x0.60 mm cane complete all as specified on drawing or as directed by Engineer-in-charge.

COMMON FOR ALL CHAIRS

Removing the existing unserviceable stiffeners and providing new stiffners made out of 1st class seasoned teak wood stiffeners complete all as specified on drawing or as directed by Engineer-in-charge.

Stool Dressing CB (FD-282 or similar)

Recaning of Stool dressing with best quality of approved plastic cane half round 2mm wide and 0.4mm thick plastic cane of white or cream ivory all as specified on drawing or as directed by Engineer-in-charge.

M & L for fixing of PVC shoes superior quality of 25mmx25mm dia with 30mm long screws in the following furniture items as specified & directed by Engr-in-charge:-

Chair Easy, Chair Dining, Chair Writing & Stool Dressing CB.

Book Case ( FD-237)

Removing the existing unserviceable shutter and providing new shutter made out of 18mm thick particle board exterior grade with 0.6 mm thick laminate in colour/shade as approved by Engineer-in-charge and providing teak wood beading all around including Hinges and lock all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable back of book case and providing new Back with 6mm thick plywood commercial type of all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Hat Stand with mirror (FD-233)

S & Fixed in repairs new mirror 5 mm thick for Hat stand with mirror of approved make with complete frame back all as specified on drawing or as directed by Engineer-in-charge.

Removing of existing unserviceable Back of Hat stand with mirror and providing new Back of 6mm plywood commercial shall be fixed with headless nail, rest all as shown on drg and as directed by Engr-in-Charge.

S&F of brass pegs with screw in place of broken/ lost pegs in hat stand with mirror, rest all as shown on drg and as directed by Engr-in-Charge.

SIDE BOARD ( FD-241,FD-1112)

Removing the existing unserviceable top of side board and providing new top made out of 18mm thick prelaminated particle board exterior grade all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable sides of side board and providing new sides made out of 18mm thick prelaminated particle board exterior grade all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge. (Note : Each side will be measured as single unit)

Removing he existing unserviceable back of Side Board and providing new Back with 6mm thick plywood commercial type of all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable Top drawer and providing New drawer made out of 12 mm thick particle board having ply on both sides. The drawer shall be run on 19 mm x 19 mm thick teak wood batten all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable Drawers (other than Top drawers) and providing new drawer made out of 12mm thick particle board having ply on both sides. The drawer shall be run on 19mm x 19mm thick teak wood bearer all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge. (Note : Each drawer will be measured as single unit)

Removing the existing unserviceable shutter and providing new shutter made out of 18mm thick particle board exterior grade with 0.6 mm thick laminate in colour/shade as approved by Engineer-in-charge including Hinges and lock all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. (Note : Each shutter will be measured as single unit)

Removing the existing unserviceable bottom of side board and providing new bottom of size 1220 x 455 mm made out of 18mm thick plywood commercial type all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable leg frame of side board and providing teak wood 2nd class hard wood leg frame all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable broken legs of side board and providing new teak wood leg 2nd class hard wood of size 45 x 45 x 125 mm but at bottom 25 x 25 mm all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge. (Note : Each leg will be measured as single unit.)

Replacement of unserviceable hinges 75mm long piano type.

S & Fixed in repairs locking device of brass 6 lever locks iron body with duplicate keys chromium plated all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. (Note : All parts as mentioned above includes 3mm thick teak wood edging duly polished wherever applied necessary as per drawing).

Table dining 8 persons (FD-273)

Replacement of existing unserviceable table top for Table dining 8 persons made out of 18 mm thick particle board exterior grade duly post-formed with 0.6 mm thick laminate in Mohigini/Walnut colour/shade as approved by Engineer-in-charge with 2 mm thick PVC edging of Make-Rehau/Pegasus/Kynes shall be fixedon two sides with strong bonded chemical adhesive through hot pressed machine all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged legs from Table dining 8 persons made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged side short rails from Table dining 8 persons made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged front/back long rails from Table dining 8 persons made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

Table dining 6 persons (FD-273)

Replacement of existing unserviceable table top for Table dining 6 persons made out of 18 mm thick particle board exterior grade duly post-formed with 0.6 mm thick laminate in Mohigini/Walnut colour/shade as approved by Engineer-in-charge with 2 mm thick PVC edging of Make-Rehau/Pegasus/Kynes shall be fixedon two sides with strong bonded chemical adhesive through hot pressed machine all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged legs from Table dining 6 persons made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged side short rails from Table dining 6 persons made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged front/back long rails from Table dining 6 persons made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

Common for Table dining 8/6 persons

S&F in repairs Triangular wooden bracket 100X100X20mm thick for all types of tables between leg & stiffners for extra strength complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE WITHOUT DRAWER 900x 600 x 760mm (FD-231,284)

Removing of existing unserviceable table top for Table without drawer 900 x 600 x 760mm and providing new table top made out of 18 mm thick particle board exterior grade duly post-formed with 0.6 mm thick laminate in Mohigini/Walnut colour/shade as approved by Engineer-in-charge with 2 mm thick PVC edging of Make-Rehau/Pegasus/Kynes shall be fixedon two sides with strong bonded chemical adhesive through hot pressed machine, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged legs from Table without drawer 900x600x760mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged side short rails from Table without drawer 900x600x760mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged front long rails from Table without drawer 900x600x760mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffners (both short & long) from Table without drawer 900x600x760mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE WITH DRAWER 900x 600 x 760mm ( FD-224,283)

Removing of existing unserviceable table top for Table with drawer 900 x 600 x 760mm and providing new table top made out of 18 mm thick particle board exterior grade duly post-formed with 0.6 mm thick laminate in Mohigini/Walnut colour/shade as approved by Engineer-in-charge with 2 mm thick PVC edging of Make-Rehau/Pegasus/Kynes shall be fixedon two sides with strong bonded chemical adhesive through hot pressed machine, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged legs from Table with drawer 900x600x760mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged side short rails from Table without drawer 900x600x760mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged front long rails from Table with drawer 900x600x760mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffners (both short & long) from Table with drawer 900x600x760mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged drawers from Table with drawer 900x600x760mm made out of first class hard wood (teak) including providing 6mm thk commercial ply to bottom of drawer complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE 900x 900mm (FD-291)

Removing of existing unserviceable table top for Table 900 x 900mm and providing new table top made out of 18 mm thick particle board exterior grade duly post-formed with 0.6 mm thick laminate in Mohigini/Walnut colour/shade as approved by Engineer-in-charge with 2 mm thick PVC edging of Make-Rehau/Pegasus/Kynes shall be fixedon two sides with strong bonded chemical adhesive through hot pressed machine, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged legs from Table 900x900mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged side short rails from Table 900x900mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffners (both short & long) from Table 900x900mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE 1200x 900mm (FD-273)

Removing of existing unserviceable table top for Table 1200 x 900mm and providing new table top made out of 18 mm thick particle board exterior grade duly post-formed with 0.6 mm thick laminate in Mohigini/Walnut colour/shade as approved by Engineer-in-charge with 2 mm thick PVC edging of Make-Rehau/Pegasus/Kynes shall be fixedon two sides with strong bonded chemical adhesive through hot pressed machine, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged legs from Table 1200x900mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged side short rails from Table 1200x900mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged front long rails from Table 1200x900mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffners (both short & long) from Table 1200x900mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

Common for all type of tables

S&F in repairs Triangular wooden bracket 100X100X20mm thick for all types of tables between leg & stiffners for extra strength complete, rest all as shown on drg and as directed by Engr-in-Charge.

Teapoy (FD-278, 34, 382)

Replacement of existing unserviceable table top for Teapoy made out of 18 mm thick particle board exterior grade duly post-formed with 0.6 mm thick laminate in Mohigini/Walnut colour/shade as approved by Engineer-in-charge with 2 mm thick PVC edging of Make-Rehau/Pegasus/Kynes shall be fixedon two sides with strong bonded chemical adhesive through hot pressed machine all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged legs from Teapoy made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffners (both short & long) from teapoy made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

Table Centre (FD-274 / 235)

Replacement of existing unserviceable table top for Table centre made out of 18 mm thick particle board exterior grade duly post-formed with 0.6 mm thick laminate in Mohigini/Walnut colour/shade as approved by Engineer-in-charge with 2 mm thick PVC edging of Make-Rehau/Pegasus/Kynes shall be fixedon two sides with strong bonded chemical adhesive through hot pressed machine all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged legs from Table centre made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffners (both short & long) from table centre made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

Table Writing/Medium/Study : (FD-33,275 )

Table top 18 Prelaminated particle board exterior grade duly post-formed with 0.6 mm thick laminate in Mohigini/Walnut colour/shade as approved by Engineer-in-charge with 2 mm thick PVC edging of Make-Rehau/Pegasus/Kynes shall be fixedon two sides with strong bonded chemical adhesive through hot pressed machine all as specified on drawing or as directed by Engineer-in-charge.

Legs as per drg

Foot rest as per drg

Stiffener as per drg

Sides of cabinet with 18mm thick pre-laminated particle board as per drg

18mm thick prelaminated particle board Cabinet door & drawer along with locking arrangement and handles as per drg

TABLE PEG (FD-236, FD-277)

Replacement of existing unserviceable table top for Table peg made out of 18 mm thick particle board exterior grade duly post-formed with 0.6 mm thick laminate in Mohigini/Walnut colour/shade as approved by Engineer-in-charge with 2 mm thick PVC edging of Make-Rehau/Pegasus/Kynes shall be fixed on two sides with strong bonded chemical adhesive through hot pressed machine all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged legs from Table peg made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged top rail from table peg made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom rail from table peg made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE BED SIDE

Taking out old ply from the back of table bed side and S&F new back ply 6mm thick commercial BWP ISI mark of the same shape and size of the existing table bed side aqll as specified and directed.

Taking out old unserviceable top of table bed side and S&F new top of particle board 18/19 of required as per existing drawing including 4mm thick teak wood beading all round all as specified and directed.

Opening out old unserviceable shelf and S&F new shelf made out of 12 mm thick ply wood commercial BWP ISI mark of size and shape including 4mm thick teak wood beading all round all as specified and directed.

TABLE DRESSING GENTS WITH MIRROR (FD-230)

Replacement of existing unserviceable drawer for Table dressing gents made out of prelaminated particles board exterior grade 12mm thick one side teak facing and balancing white on the other side and 12x12mm wooden beading around all as specified on drawing or as directed by Engineer-in-charge. Note-Each drawer should be measured as single unit

S & Fixed in repairs new mirror 5mm thick of approved make with full frame all as specified on drawing or as directed by Engineer-in-charge.

S & Fixed in repairs new top made out of 18 mm thick pre laminated particle borad exterior grade of approved make, all as specified on drawing or as directed by Engineer-in-charge.

TABLE DRESSING LADIES (FD-251)

S & Fixed in repairs table top of Table dressing ladies with 18 mm thick pre-laminated particle Board exterior grade of approved make, all as specified on drawing or as directed by Engineer-in-charge.

S&Fixed in repairs new Glass shutters of Table dressing ladies all as specified on drawing or as directed by Engineer-in-charge.(Each glass shutter shall be measured as single unit)

Removing the existing unserviceable Aluminium channel and S & Fixed in repairs Aluminium Channel all as specified on drawing or as directed by Engineer-in-charge.

S & Fixed in repairs new back suport made out of 6 mm thick plywood for mirror of Table dressing ladies all as specified on drawing or as directed by Engineer-in-charge.

S & Fixed in repairs new mirror 5 mm thick for Table dressing ladies of approved make with complete frame back all as specified on drawing or as directed by Engineer-in-charge.

Supply & fixing of Knob of aluminium anodized dark brown in shade as approved by GE & in the following furniture items with screws as specified & as directed by Engr-in-Charge:-

Side board, Table 3'x2' with drawer, Table Writing/Medium/Study, Table dressing gents with mirror & Table dressing ladies with mirror.

M&L preparation of old wood surfaces by scraping/removing old polish completely and rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying Melamyne polish upto glossy finish of Mohigini/Walnut Color irrespective of drawing complete all as specified on drawing or as directed by Engineer-in-charge. for the following furniture articles:-

Bed Ply top FD-246/ 247

Chair dining FD-228, FD-279 or Similar

Chair writing FD-202, FD-250, FD-280 or similar

Chair Easy FD-203,FD-229 or similar

Stool Dressing FD-282

Book Case FD-237

Bin linen small FD-244

Hat Stand with mirror FD-233

Side Board FD-241,FD-1112

Table dining 6/8 persons FD-273

Table without drawer 900x600x760mm FD-231,284

Table with drawer 900x600x760mm FD-224,283

Table 900x900mm FD-291

Table 1200x900mm FD-273

Teapoy FD-278, 34, 382

Table centre FD-274 / 235

Table writing FD-33,275,

Peg Table FD-236, FD-277

Table bed side

Table dressing Gents with mirror FD-230

Table dressing Ladies with mirror FD-251

ANAND FURNITURE

m/s tripurari enterprises

RAGHUVANSH TRADERS

JAISWAL ENTERPRISES