REPAIRS TO ROOF COVERING, ROOF TREATMENT, FALSE CEILING, JOINERY, PLASTERING, FLOORING, PLUMBING, SANITARY FITTING AT MLIRC, GLOBE AREA, EME, SIGNAL, RECORDS MLIRC, MT JL WING, AND OFFICERS MESS MLIRC AT AREA NO. 3 UNDER GE BELGAUM

Amount

Taking down chowkhat with shutters (without taking off shutters from the frame) area not exc 1.5 Sqm each all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n exc 4 Sqm each all as specified and directed.

Taking down shutters of any description n exc 1sqm each all as specified and directed.

Taking down shutters of any description area exc 1 sqm and n.exc 2 sqm each all as specified and directed.

Dismantling wrought iron or mild steel work of any description and in any position not otherwise provided for all as specified and directed.

Taking down cement plaster on brick or stone wall or ceiling concrete etc. including racking out joints hacking for key scrubbing down with water etc., all as specified and directed.

M&L for plain cement concrete 1:3:6 type C1 using 20mm graded stone aggregate as in surface channels, drains, etc. including necessary form work/ moulds including demolition of existing unserviceable PCC drains of any description and making good the disturbed surfaces all as specified and directed.

M&L plain cement concrete 1:2:4, type B0, using 12.5mm graded stone aggregate as in roof kerbs, mud stops, coving, etc. with rounded or chamfered edges including demolition of existing plain cement concrete of any description and size and making good disturbed surfaces all as specified and directed

M&L plain cement concrete 1:3:6, type C-1, using 20mm graded stone aggregate as in eves filling between wall and tile/ sheet roofing including demolition of existing plain cement concrete of any description and size and making good disturbed surfaces all as specified and directed

M&L for providing precast cement concrete louvres and jallies, 1:3:6, Type C0, using 12.5mm graded stone aggregate, 25mm thick (measured solid) including all mouldings but excluding frame, set in cement mortar 1:4 all as specified and as directed.

M&L for pre-cast cement concrete solid block masonry, exc 10 cm width, blocks cast in PCC 1:3:6, type C1, using 20 mm graded stone aggregate and setting in CM 1:6 including demolition of existing unserviceable brick/ PCC block masonry built in cement mortar in any position below or above ground level and making good disturbed surfaces all as specified and directed.

Cutting, chases for concealed water tubing and making good in CM 1:3 cutting not exceeding 10 cm girth in brick/ PCC block wall all as specified and directed.

Cutting holes in brick walls built in cement mortar for inserting holdfasts, depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall exc. half brick but not exc. one brick and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required all as specified and directed.

Cutting holes in stone masonry walls built in cement mortar for inserting holdfasts, depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall exc. half brick but not exc. one brick and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required all as specified and directed.

M&L for 2nd class hard wood in scantling, clean sawn fixed in unframed work including dismantling of existing unserviceable timber scantling 40 Sq.cm and over in section and in any position in un-framed work and making good disturbed members all as specified and directed.

M&L for 2nd class hard wood plain fillets, square, rectangular or triangular in section, wrought, secured with nails or beads; sectional area exc 6 and n.exc. 13 Sq.cm including dismantling of existing unserviceable fillets, rails, posts, rafters, purlins, etc. and making good disturbed members all as specified and directed.

M&L for 2nd class hard wood board, 20mm thick, planned on one side and the other clean sawn, with butt joints and fixed with nails in any situation including dismantling unserviceable boarding of any description and making good disturbed members all as specified and directed.

M&L for 2nd class hard wood chowkhat or frames, plain, solid, wrought, framed and rebated on the solid rounded or chamfered, put together with glue pinned at joints, fixed in position all as specified and directed.

M&L for 35 mm thick second class hard wood, Plain framed, panelled shutter (two panel) with lock rail and panel of 12mm thick plywood BWR 7 ply with commercial veneers on both faces, sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for 30mm thick 2nd class hard wood glazed/ gauged window/ ventilator shutters, open rebated and prepared to receive glass, gauze, etc. (divided into square with plain, chamfered or rounded, mitred and rebated sash bars any numbers), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (b) and fitted to chowkats all as specified and as directed.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, fitted to chowkats all as specified and as directed.

M&L for 18mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination on the other side with white lamination, as in cub board shelves/ cabinet works fixed with screws, fixed in repairs, all as specified and directed

M&L for 12mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination on the other side with white lamination fixed to aluminium framework with screws all as specified and directed

M&L for aluminium frame work as in doors, partitions and windows using powder coated aluminium sections including provision of glazing clips, hinges, handles, etc all as specified and as directed. Notes: (i) All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufacturer's catalogue for the corresponding aluminium sections/ fittings. (ii) The rate quoted deemed to include necessary grouting/ embedding of the aluminium frames/ supports into floors/ walls and making good the disturbed surfaces to match with the existing surfaces and provision of necessary rubber gaskets. (iii) Particle board/ glass panels shall be measured and paid separately.

M&L for solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on both sides reinforced with M.S. Square tube, supplying and fixing in opening as per specification and drawing all as specified and as directed.

M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelaminated PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of prelaminated PVC sheets on both sides to be fitted in the M.S. frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing all as specified and directed

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm Plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing all as specified and directed

S&F MS butt hinges 100mm in size, medium weight, cold rolled all as specified and directed.

S&F MS butt hinges 75mm in size, medium weight, cold rolled all as specified and directed.

S&F 300mm long mild steel helical door spring, ordinary rat tail pattern spring, including roller and roller plate complete all as specified and as directed.

S&F in repairs continuous (piano) hinges, mild steel, bright finish or electro galvanised with width of flaps when open 30mm all as specified and as directed.

S&F in repairs aluminium anodised barrel tower bolt 200mm size all as specified and directed.

S&F aluminium anodised barrel tower bolt 150mm size all as specified and directed.

S&F aluminium anodised barrel tower bolt 100mm size all as specified and directed.

S&F aluminium handle, 'D' type, anodised 150 mm in size all as specified and directed.

S&F in repairs aluminium handle, 'D' type, anodised 125 mm in size all as specified and directed.

S&F aluminium handle, 'D' type, anodised 100 mm in size all as specified and directed.

S&F in repairs 100mm long aluminium anodised hasp and staple, safety type with hinge pin including bolt to hinge plate fixed with screws complete all as specified and as directed.

S&F in repairs 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F 200mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S& F in repairs floor door stopper of brass body and tongue, anodised, with 140mm long cover plate and hard drawn steel spring, fixed in floor all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

S&F in repairs 100mm size mortise lock, brass, vertical type, four levers, including cutting holes in existing pressed steel frames, all as specified and directed. Make: Godrej or equivalent.

S&F in repairs 25mm dia mild steel powder coated curtain rods, fancy type, all as specified and as directed. Make: MARVEL or equivalent

S&F in repairs 20mm dia stainless steel single curtain rod of 16 guage with rounder fancy ends. Fixed to bracketswith necessary screws including drilling and plugging the holding screws, all as specified and as directed.

S&F in repairs fancy type brackets, mild steel with antique finish or colour with rounded fancy ends suitable for holding 25mm dia single curtain rods, fixed to wall with necessary screws including drilling and plugging the holding screws and making good the wall surfaces all as specified and directed. Make: MARVEL or equivalent

S&F in repairs fancy type brackets, stainless steel with glazing finish for holding single curtain rods with rounded fancy ends, fixed to wall with necessary screws including drilling and plugging the holding screws and making good the wall surfaces all as specified and directed. Make: MARVEL or equivalent

S&F in repairs fancy type brackets, mild steel with antique finish or colour with rounded fancy ends as in middle supports for holding 25mm dia single curtain rods, fixed to wall with necessary screws including drilling and plugging the holding screws and making good the wall surfaces all as specified and directed. Make: MARVEL or equivalent

S&F in repairs Door closer, of aluminium (die cast) body, hydraulically regulated, designation No 2, universal type, suitable for door shutters of weight between 36 to 60kg, all as specified and directed

M&L for mild steel small articles like bands, straps, including bolts, if required; hooks (stay), hook and pintle hinges; large hasps and staples; hand made sliding bolts; clamps; hold fasts; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar articles conforming to Fe-290 Gde-E-165 all as specified and as directed.

S&F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165 all as specified and as directed.

S&F mild steel works in tubular trusses, rafters, purlins, etc. including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 dismantling the existing unserviceable mild steel members of any description and size and making good disturbed membersall as specified and as directed.

M&L for mild steel flats as in wind ties for roof including securing bolts and necessary drilling, conforming to Fe-290 Gde E-165 including dismantling the existing unserviceable mild steel members of any description and size and making good disturbed members all as specified and as directed.

Repairs to loose hanging mild steel window/ ventilator shutters not exceeding 1sqm each including repairs to hardwares by welding for smooth functioning of the shutters including making good the welded surfaces to match with the existing window/ ventilator surface all as specified and as directed. Notes: (i) Windows are to be fixed to the buildings upto 3 stories height. (ii) Hardwares wherever required to be replaced shall be measured and paid separately under respective items of this Schedule at supply only rates.

Supply only mild steel box type hinges, suitable for steel windows all as specified and as directed.

M&L for Mild steel handles, suitable for steel windows, fixed with necessary nut, bolt and washers, fixed in repairs all as specified and as directed.

M&L for Mild steel peg stays, 300mm long, suitable for steel windows, fixed with necessary nut, bolt and washers, fixed in repairs all as specified and as directed.

M&L for stainless steel hand rails made out of 16 SWG, 60 mm to 20mm dia stainless steel pipes of grade 304, confirming to internationally accepted design and shapes, includng cutting to size and bending to shape as required at site, welded, mirror polished and grouting in to wall/floor with necessory mounting plate or ancor bolt incl dismantling of existing handrails of any description and type al as specified and as directed.

M&L for Mangalore pattern or similar tiles in roofing, interlocking at side joints, laid dry, including dismantling of existing unserviceable tiles of any description and size and making good disturbed roof members all as specified and as directed.

Dismantling of existing single layer Mangalore pattern or similar roofing tiles interlocking at side joints, laid dry and re-laying the same in new or old position and making good disturbed roof members all as specified and as directed.

M&L for Mangalore pattern or similar tiles in roofing, bedded and jointed in CM 1:6, including dismantling of existing unserviceable tiles of any description and size and making good disturbed roof members all as specified and as directed.

M&L for ridge/ hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in CM 1:6 including dismantling of existing unserviceable ridge tiles of any description and size and making good disturbed roof members all as specified and directed.

S&F corrugated galvanised mild steel sheeting with grade of zinc coating 275, 0.63 mm thick, with two corrugation side laps in roofs, walls, etc. fixed with L-type or J-type or cranked hook bolts including dismantling of existing unserviceable CGI roofing sheets of any description and size and making good disturbed roof members all as specified and as directed.

S&F plain galvanised mild steel sheeting with grade of zinc coating 275, 0.8mm thick, in ridges, hips, valley gutter, drip and straight flashings including dismantling of existing unserviceable PGI sheets of any description and size and making good disturbed roof members all as specified and directed.

M&L for 6mm thick asbestos cement corrugated or semi-corrugated sheets in roofs, walls, etc. fixed with L-type or J-type or cranked hook bolts including dismantling of existing unserviceable AC roofing sheets of any description and size and making good disturbed roof members all as specified and directed.

M&L for 6 mm thick asbestos cement two piece adjustable serrated ridge for corrugated sheets in roofs fixed with ‘L’ type or ‘J’ type or cranked hook bolts including dismantling of existing unserviceable AC ridge sheets of any description and size and making good disturbed ridge/ roof members all as specified and directed

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.45mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions including dismantling of existing unserviceable corrugated roofing sheets of any description and size and making good disturbed roof members all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for pre-painted galvalume coated high tensile plain steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.45mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions including dismantling of existing unserviceable corrugated roofing sheets of any description and size and making good disturbed roof members all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for 4mm thick Aluminium Composite Panel comprising of a core containing not less than 70% non combustible mineral filling sandwiched between two skins of 0.5mm thick aluminium alloy PERALUMAN-100 (AlMg1-NS41), weight not less than 7.6 kg per sqm, complete with all necessary sub-structures, anchors, hardware and fittings to provide a total installation, fixed to existing wooden/ steel members including dismantling of existing unserviceable panel all as per manufacturers instructions, fixed in repairs, all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc. Make: Alstrong/ Aludecor/ Alucobond

M&L for 6mm thick multi wall plain polycorbonate sheets, as in roofing/ ceiling/ cladding fixed with self drilling fasteners as per manufacturers instructions including covering edges with anti dust tape and dismantling of existing unserviceable corrugated roofing sheets of any description and size and making good disturbed roof members all as specified and as directed.

M&L for closing bolt holes or other similar holes in old Asbestos cement sheets by sealing with one bitumen and one plain G.I. washer on either side and 8mm dia bolt and nut, bolt not exceeding 25mm in length all as specified and as directed.

M&L for closing bolt holes or other similar holes in old Galvalume sheets by sealing with one plain G.I. washer on one side and self tapping screw bolt not exceeding 25mm in length all as specified and as directed.

M&L for Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and as directed.

M&L for 500 litres capacity rotational moulded polyethylene (HDPE) water storage tanks, 'ISI' marked, cylindrical, vertical with closed top conforming to IS 12701-1989 having two layers wall construction with manhole lid and suitable locking arrangement including making holes for inlet, outlet and over flow pipes, hoisted and fixed in position including testing complete all as specified and directed.

M&L for 1000 litres capacity rotational moulded polyethylene (HDPE) water storage tanks, 'ISI' marked, cylindrical, vertical with closed top conforming to IS 12701-1989 having two layers wall construction with manhole lid and suitable locking arrangement including making holes for inlet, outlet and over flow pipes, hoisted and fixed in position including testing complete all as specified and directed.

Cleaning and removing all scale dirt etc from tanks capacity exc 250 n exc 500 ltr and from mouths of circulating pipes etc complete as specified and directed.

Cleaning and removing all scale dirt etc from tanks capacity exc 500 n exc 1000 ltr and from mouths of circulating pipes etc complete as specified and directed.

M&L for providing roof treatment with APP modified water proofing membrane with the following specifications all as specified and directed.

Removing existing roof/ chajjas treatment of any type like plastic felt/ HP tiles of any description including taking down existing plastering/ concrete of any thickness and cleaning the top surface of RCC slab with wire brush including removal of debris to a distance exc 50m but n exc 100m

Brushing with neat cement slurry @ 3Kg/Sqm on cleaned RCC slab surfaces and rendering 10 mm thick in CM 1:3 mixed with water proofing compound and finishing surfaces even and smooth without using extra cement. Note: Water proofing compound shall be measured and paid separately

Preparation of plastered surfaces by removing dust, dirt & applying oil bound bituminous primer at 0.2kg per Sqm & providing APP modified water proofing membrane weight not less than 4kg/Sqm reinforced with non oven polyester mat weight not less than 160gms per Sqm including min 10cm side/over lap & including applying a coat of blown hot bitumen grade 85/25 over membrane at 1.2kg per Sqm & on drying apply a coat of solar reflective bituminous aluminium paint at 0.1kg/sqm.

S&F PVC (SWR) eaves gutter half rounded 150mm bore including pipe accessories PVC holder bats bolts nuts etc. including taking down existing unserviceable gutters of any description and size and making good disurbed surfaces all as specified and directed.

S&F 4mm thick High Pressure Steam Cured (HPSC) non asbestos fibre cement building board in false ceiling with aluminium anodized snap grids of 60x60cm with Tee section 35x25x1.25mm, angle section 25x25x1.25mm thick including 2mm dia GI hanging wire including all hanger fittings etc and applying three coats of white wash on ceiling including dismantling of existing unserviceable false ceiling boards of any description and size alongwith snap grid frame works including making good disturbed wall/ ceiling surfaces all as specified and directed.

M&L for coloured ceramic tiles, matt finished, 7mm thick, area of each tile exc 0.06 Sqm but not exc 0.11 Sqm as in floor, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 including dismantling of existing unserviceable tiling alongwith cement mortar bedding (but not backing) and removing rubbish off the premises all as specified and directed.

M&L for coloured glazed ceramic tiles 300mm x 200mm x 5.50 to 6mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 including dismantling of existing unserviceable tiling alongwith cement mortar bedding (but not backing) and removing rubbish off the premises all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in flooring, laid and jointed with neat slurry and pointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 15mm thick screed bed in cement mortar 1:4 including dismantling of existing unserviceable stone tiles alongwith cement mortar bedding (but not backing) and removing rubbish off the premises all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in risers of steps, skirting, dado, cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 10mm thick backing coat in CM 1:4 including taking down existing cement plaster and raking out joints, hacking for key, scrubbing down with water, removing rubbish off the premises etc. complete all as specified and directed.

M&L for machine cut Granite stone tiles, 20mm thick, premium quality, any colour, as in flooring, set and jointed with neat cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab over 15mm thick screed bed in cement mortar 1:4 including rubbing and polishing including dismantling of existing unserviceable stone tiles alongwith cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and as directed.

M&L for machine cut Granite stone tiles, 20mm thick, as in risers of steps, skirting, dado, cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the tiles including bull nosing the edges, rubbing and polishing complete including 10mm thick backing coat in CM 1:4 including dismantling of existing unserviceable stone tiles alongwith cement mortar bedding (but not backing) and removing rubbish off the premises all as specified and directed.

M&L for Granite of premium quality , 20mm thick, as in risers of steps, skirting, dado, cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the tiles including bull nosing the edges, rubbing and polishing complete including 10mm thick backing coat in CM 1:4 on fair faces of brickwork or concrete surfaces in backing coat of skirting/dado etc, all as specified and directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, with grey cement and pigments, set jointed and pointed in neat cement slurry, laid over and including 15mm thick screed bed in cement mortar 1:6 as in pathways, etc. including dismantling of existing unserviceable stone slab/tiling alongwith cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40mm graded aggregate as in sub base/ levelling course for flooring all as specified and directed.

M&L for 60mm thick machine pressed precast concrete interlocking coloured paver blocks, M-35 grade, any shape and size with anti skid finish on top confirming to IS 15658-2006, including 75mm thick sand filling, watering, consolidation and dismantling of existing unserviceable paver blocks and removing rubbish off the premises all as specified and directed.

M&L for plain cement concrete 1:3:6, type C2, (Using 40 mm graded stone aggregate), 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar, including demolition of existing plain cement concrete of any description and size and making good disturbed surfaces etc. complete all as specified and directed.

M&L for grinding, polishing and waxing the existing old Terrazzo/ Tandoor/ Kota stone flooring/ skirting with necessary grey cement, marble powder, etc. complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1:3 on soffit of roof ceiling, finished fair and even without using extra cement complete all as directed.all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on other than fair faces of brick work or stone masonry surfaces finished even and smooth without using extra cement complete all as directed. Note: Water proofing compound shall be measured and paid separately.

Supply only integral water proofing compound all as specified and as directed.

M&L for removal of existing vegetations/ trees not exceeding 30cm girth on top/ sides of buildings including digging out roots, pouring sulphuric acid, making good disturbed portions with cement mortar 1:3 including provision of 2 coats of cement based paint on walls to match with adjacent finishes all as specified and as directed.

M&L for 5.5mm thick sheet glass ordinary quality in square n exc 0.5 sqm in each pane fixed to aluminium shutters all as specified and directed.

M&L for 4mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane all as specified and directed.

M&L for 4mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane icluding hacking out old broken glass of any thickness all as specified and directed.

M & L for 4mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane including hacking out old broken glass of any description and size and making good disturbed surfaces all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of ceilings including necessary preparation of surfaces all as specified and as directed.

M&L for three coats of white wash on newly plastered surfaces of walls, pilasters, cornices, etc. including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable), any colour, over a coat of primer on newly plastered walls, pilasters, cornices, etc., including necessary preparation of surfaces with chalk whiting all as specified and as directed.

M&L for two coats of cement based paint, any colour, on newly plastered surfaces of walls, pilasters, cornices, etc., over a coat of primer including necessary preparation of surfaces all as specified and directed.

M&L for preparing surface of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of creosote oil all as specified and directed.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for one coat of synthetic enamel paint on old painted wooden surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and as directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

S&F 15mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors including taking up or down existing unserviceable GI tubes of any grade and making good disturbed surfaces all as specified and directed.

S&F 20mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors including taking up or down existing unserviceable GI tubes of any grade and making good disturbed surfaces all as specified and directed.

S&F in repairs 15mm bore bib taps, cast copper ally with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S & F in repairs 15 mm bore Bib tap, long body, brass chromium plated, fancy type, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

S&F in repairs 3 way mixer tap for mixing hot and cold water, fancy type, brass chromium plated screwed down for 15mm bore GI pipe all as specified and directed. Make: JAQUAR/ JOHNSON/ CERA

S&F in repairs 15mm bore PTMT bib taps, standard type, (Minimum weight 90gms) any colour, high pressure screwed for iron pipe all as specified and as directed.

S&F in repairs 15mm bore stop valves, brass CP screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions all as specified and as directed.

S&F in repairs 15mm bore stop valves, fancy type brass CP, with long shank and cup (concealed type), screwed down high pressure, screwed both ends for iron pipe for unions all as specified and as directed.

S&F in repairs pillar taps brass chromium plated with capstan heads, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed down high pressure screwed for 15mm bore GI pipe all as specified and directed.

S&F fancy type pillar taps brass chromium plated with long screwed shanks and fly-nuts, screwed down high pressure screwed for 15mm bore GI pipe all as specified and directed. Make: JAQUAR/ PARRYWARE/ JOHNSON

S&F in repairs Vitreous China wash basin, white, flat back, size 550x400mm, excluding taps, waste chain and plug and porcelain stopper but including brackets etc complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, fixing bolts, etc, connecting to drain pipe and flushing pipe all as specified and as directed.

S&F in repairs plastic water closet seat for EWC, closed pattern with flat bottom and cover, any colour as approved by GE and mild steel chromium plated or aluminium hinging device all as specified and as directed.

S&F in repairs, Vitreous China urinal, bowl type, flat back/ corner wall, 465 x 355 x 265mm size (minimum), white, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including provision of grating and union for discharge pipe, 15mm bore PTMT urinal spreader, waste pipe, (excluding flushing cistern, flush pipe) all as specified and as directed.

S&F in repairs PVC connection 15mm size with PTMT nuts, 450mm long all as specified and directed.

S&F in repairs PVC connection 15mm size with PTMT nuts, 750mm long all as specified and directed.

S&F in repairs PTMT waste couplings, half or full threaded, minimum weight 45 gms suitable for 32mm bore discharge pipes all as specified and directed.

S&F in repairs PVC flexible pipe (waste pipe), 900mm long, suitable for 32 mm bore waste coupling of sink/ wash hand basin all as specified and directed.

S&F in repairs PVC flexible pipe (waste pipe), suitable for urinals all as specified and directed.

S&F in repairs 1mm thick stainless steel sink, overall size not less than 495x420mm, bowl size not less than 410x330x160mm, with plug, washers and wastes including bedding in cement mortar, fixing cantilever brackets and connecting union to pipe all as specified and as directed.

S&F in repairs shower rose swivel type brass CP shower rose 125mm size suitable for fixing with 15mm bore pipe all as specified and as directed.

S&F in repairs vitreous china squatting pan, Orissa pattern, size 580mm x 440mm, white, with integral foot rest (excluding flushing cistern) including 'P' or 'S' trap including lime concrete bedding etc. complete all as specified and directed.

S&F in repairs syphonic action type low level PVC flushing cistern, 10 litres capacity, white, with inlet, ball valve, float, handle and flush pipe etc complete all as specified and directed.

M&L for 40mm bore Ligh Density Polyethylene pipes (LDPE) of pressure rating 4 kgf/cm2 etc.fixed complete to walls, ceilings or laid in floors, fixed in repairs, all as specified and as directed.

M&L for 50mm bore Ligh Density Polyethylene pipes (LDPE) of pressure rating 4 kgf/cm2 etc.fixed complete to walls, ceilings or laid in floors, fixed in repairs, all as specified and as directed.

M&L for 50mm bore Ligh Density Polyethylene pipes (LDPE) of pressure rating 4 kgf/cm2 etc.fixed complete to walls, ceilings or laid in floors, fixed in repairs, all as specified and as directed.

S&F in repairs 110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including taking down existing unserviceable pipes of any description and size and making good disurbed surfaces all as specified and directed.

S&F 110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

S&F in repairs 75mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including taking down existing unserviceable pipes of any description and size and making good disurbed surfaces all as specified and directed.

S&F in repairs 110mm bore UPVC (SWR) bends any radius with access door all as specified and directed.

S&F in repairs 75mm bore UPVC (SWR) bends any radius with access door all as specified and directed.

S&F in repairs 110mm bore UPVC (SWR) branch piece, single (single Y) equal or unequal with access door all as specified and directed.

S&F in repairs 75mm bore UPVC (SWR) branch piece, single (single Y) equal or unequal with access door all as specified and directed.

S&F in repairs110mm bore UPVC (SWR) branch piece, double (double Y) equal or unequal with access door all as specified and directed.

S&F in repairs 75mm bore UPVC (SWR) branch piece, double (double Y) equal or unequal with access door all as specified and directed.

S&F in repairs 110mm bore UPVC (SWR) junction, single (single T) equal or unequal with access door all as specified and directed.

S&F in repairs UPVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm dia outlet all as specified and directed.

S&F in repairs stainless steel grating with frame 100mm dia with or without hole for waste pipes connection all as specified and directed.

S&F in repairs UPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and directed.

S&F in repairs UPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and directed.

M/s. N D KALING

M/s. KIRAN M CHOUGULE

M/s. VIJAY ELECTRICALS

ASHOK M RAJGOLKAR