ANNUAL MAINT TO WALL TOILET KITCHEN PLASTERING ROOF TREATMENT FLOORING BATHROOM SANITARY FITTINGS AND OTHER MISC REPAIRS IN MD ACCN AT RA BAZAR, AOT AREA, SANJAY ENCLAVE UNDER AGE B/R-I OF GE (N) MEERUT CANTT

Amount

Taking down old existing water proofing treatment from the top of RCC/ arch slab, including taking down existing PCC padding or plaster and hacking the top of RCC slab, cleaning with water and disposal of rubbish off the premises complete all as specified & directed.

M&Lfor nominal mix concretes 1:2:4 type B-O(using 12.5 mm graded stone aggregates) as in padding on roof finished even and fair without using extra cement complete all as specified & directed.

M&L for 10mm thick cement paster in CM 1:4 mixed with WPC @ 2 % by weight of cement finised even and smooth without using extra cement on roof surface when concreate is green and wall (WPC will be measured and paid seperately as supply only rate) complete all as specified & directed.

M&L for cutting grooves in brick/ concrete wall 75 mm wide and 65 mm deep and shaping horizontal face of groove and making good disturbed surface in CM 1:3 after inserting APP membrane (Chasing shall be cut where height of parapet wall is more than 300mm.) complete all as specified & directed.

Supply only liquid water proofing compound complete all as specified & directed.

M&L for surface Preparation: The surface to receive the treatment shall be thoroughly free of laitance, scales, oil or any other loose material. It should be made free of any sharp objects. Cleaning of PCC shall be done with wire brushing to attain smooth levelled surface. Cracks shall be rectified, filled using dual shrinkage compensated Repair Mortar and dried for 72 hours before laying the liquid applied membrane. Grout: Providing Chemical injection treatment in the form of pressure grouting to the construction joint and cracked portion at 1m c/c by injecting cement slurry mixed with dual shrinkage compensated cementitious grout Injection grout additive, in the required consistency through the pre fixed PVC nozzles in the 18 mm dia holes, fixing of PVC nozzles with instant setting cement. Angle fillets/Coving: Providing and making of fillet, 50mm x 50mm on sharp corner of terrace with cement sand polymer mortar (add “multipurpose mortar”, 10% by weightofcement). First apply the bonding coat of Multi-Purpose Polymer 5-10% diluted in water and add to cement slurry. Apply the bonding slurry and apply the polymer mortar over the sharp edges. Note: Grouting will be done when and where ever required. Treatment of pipe entry points: Preparing the inside surface of core and PVC /MS Pipe by roughening using suitable Sand paper to get better adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to remove any laitance or loose flaky particles. Packing the gap using free flowable non shrink cement polymer based grout up to the surface of the bore while the bonding agent is in tacky state. the periphery of PVC pipe should be sealed with Hybrid PU Sealant or dual shrinkage compensated Micro concrete Note: Will be done when and where ever required Application of Asian Paints two component Epoxy Primer (Resin & Hardener) on the cleaned surface for bonding of Polyurethane with the existing concrete surface. 33 % water dilution is recommended with the pure mixed primer. The primer mixing ratio will be 1:3(Resin:Hardner) Supplying, providing and applying waterproofing treatment to Podium area with single component highly elastomeric seamless cold applied modified PU coating complete as per manufacturer’s specifications and application methodology. The same coating shall be applied in two coats achieving a total thickness of 1mm. The coating shall have a dual combination of 280% elongation. Material coverage 1.2kg /sq.mt. (Note: Contractor is required to deposit 100% CA quantity to the Engr-in-Charge, within 15 days of acceptance of contract.

Taking down of cement plaster of any description from brick or stone wall etc. including raking out of joints, hacking for key, scrubbing down with water etc complete all as specified & directed.

M & L 15 mm thick rendering in CM 1:6 on fair faces of brick or concrete surfaces finished even and fair complete all as specified & directed.

M & L for applying 15 mm thick rendering using ready mix plaster bags in CM 1:4 on brick / concrete surfaces of external walls finished even and fiar, using water proofing compound @ 3% by weight of cement or as per manufacturer instructions, complete all as specified and directed : Note:- Water proofing compound shall be measured and paid sepratly complete all as specified & directed. Note : Contractor is required to deposit ready mix bags for 100% CA quantity to the Engr-in-Charge within 15 days of acceptance of contract

M&L Rendering 5 mm thick on fair faces of concrete surfaces, finished even and smooth on ceiling in cement mortar (1:3), complete all as specified & directed.

M & L Preparation of new plastered surface of wall by applying 3mm thick wall care putty and making the surface smooth Finishing walls and applying Acrylic Smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)using roller for painting complete all as specified & directed.

M & L Preparation of new plastered surface of wall by applying 3mm thick wall care putty and making the surface smooth and applying two coat of oil emulsion distemper over one coat of primer using roller for painting complete all as specified & directed.

M & L Preparation of new plastered surface of ceiling and applying 3mm thick wall care putty and making the surface smooth and applying two coat of oil emulsion distemper over one coat of primer using roller for painting complete all as specified & directed.

M & L Preparation of Complete removal of existing treatmentplastered old surface of of wall by applying 3mm thick wall care putty and making the surface smooth Finishing walls and applying Acrylic Smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)using roller for painting complete all as specified & directed.

M& L Preparation of Complete removal of existing treatment by mechanical means plastered old surface of wall and applying 3mm thick wall care putty over one coat of primer and making the surface smooth and applying two coat of oil emulsion distemper using roller for painting complete all as specified & directed.

M&L for preparation of new steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide premier complete all as specified & directed.

M&L for preparation of Old steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with one coats of synthetic enamel paint over a coat of red oxide premier complete all as specified & directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of old wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise complete all as specified & directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars, shouldered and/or riveted, or forged into spikes, framed guard bars etc and similar work conforming to Fe-290 (Gde-E-165) complete all as specified and directed

M&L for rolled mild steel angle iron work as in door frames complete, drilled for fixing of hinges etc. also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and directed.

Demolition of brick work or stone/boulder masonary built in cement mortar incl all quoins arches pillars etc.complete all as specified & directed.

M&L for Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius with old size bricks built in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M & L for brick work with sub class fly ash bricks straight or curved on plan exc 6 m mean radis built in CM 1:6 complete all as specified and as directed.

M&L for Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius with old size bricks built in cement mortar 1:4 but except bricks complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc. 15cm thickness (below or above ground level) complete all as specified & directed.

M&L for cement concrete 1:4:8, type D2(40mm graded stone aggregate) as in 75mm thick sub base complete all as specified & directed.

M&L for Broken stone or boulder Hardcore of guage n exc 63 mm, deposited, spread and levelled in layers not exc 15 cm thick , watered and rammed to a true surface etc all as specified and directed by Engineer- in- charge

M&L for chequered cement concrete colour tiles glossy finish size 300mm cmx300mmx25 mm thick, with colour pigment, set, jointed and pointed in neat cement slurry over and including 20 mm thick screed bed in cm (1:6) complete all as specified & directed.

M&L for Plain Cement concrete Type B-0, 1:2:4 (12.50mm graded aggregate), 25 mm thick as in sub-base of floors complete all as specified & directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to store andd rubbish off the premises complete all as specified & directed.

M&L for Non-skid coloured ceramic tiles 7 to 8 mm thick square/ rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in loors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

S&F non skid coloured ceramic tiles coloured of 7 to 8 mm (squre/ rectungular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors set and jointed in neat cement slurry and pointed with white or coloured cement over and including 15mm screed bed in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350X250X7mm/450mm x 350mm x 7mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including rendering 10mm thick in cement mortar (1:4) , complete all as specified and directed.

Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) exc 1.50 m and n.exc 4.00 Sqm each complete all as specified & directed.

Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) not exc 1.50 Sqm each complete all as specified & directed.

Taking down shutters of any description exc 1.00 m and n.exc 2.00 Sqm complete all as specified & directed.

S&F, for 35mm thick, second class HW in glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. size of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed by Eng-in-Charge.

S&F 35 mm thick flush shutters, conforming to IS 2202 (Part-I) - 1999 solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

S & F for 30mm thick Factory made single extruded WPC (Wood Polymer Composite) solid Moulded WPC door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S & F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65X100mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, as per specification complete all as specified & directed.

S&F Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined to-gether with solvent cement as per specification complete all as specified & directed.

S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed

S& F aluminium anodised sliding door bolts with hasp and stapple extruded section or cast aluminium alloy 300 mm long complete all as specified & directed.

S&F, butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified and directed.

S&F, extruded aluminium alloy handles, fabricated type, anodised of size 100 mm complete all as specified and directed.

S&F in repair , Floor door stopper of aluminium alloy body and tongue with rubber cover ends, Complete all as specified and directed by Engineer-in-Charge.

M&L, in repair, 18/19mm thick Soild WPC board, exterior grade, prelaminated one side with decorative choice laminations and other side balanceing white lamination, fixed with screws to WPC frame work in cup boards, rebated or flat edged fancy handle , Magnite lock complete all as specified and directed.

S&F continuous (piano) hinges, mild steel bright finish or electrogalvanised, width of flap 40 mm complete all as specified and directed.

S&F hasp & staples 125mm in size, safety type alu. anodised fixed with screws complete all as specified & directed.

M&L for 18-20mm thick BLACK/RED granite stone slab machine cut in skirting/dado, cooking platform, jams, pillars, windows cills and the like laid over and including 10mm thick screed bed or backing coat in cement mortar (1:4) and jointed with grey cement slurry and pointed with white cement and with admixture or pigment to match the shade of granite stone including grinding and polishing complete all as specified & directed.

M&L for rounding to edges of stone slabs two edge full round, such as in steps,cooking platform and other similar situation complete all as specified and directed.

S&F, in repair, aluminium (Die cast) body, Door closer, hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified & directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples including necessary beadings complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples including necessary beadings complete all as specified and directed.

Dismantling water tank of capacity exc 500 ltrs but not exc. 1000 Ltrs complete all as specified and directed.

S&F rotational moulded polyethene water storage tank ( cylinderical verticle with closed top) hoisted and fixed in position all as specified in SSR Part-I. (Cap 500 ltrs capacity). complete all as specified and directed.

S&F in repair, Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 ltr capacity hoisted and fixed in position all as specified in SSR Part I, including taking down of exiting tank, complete all as specified and directed by Engineer in Charge.

S&F 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) complete all as specified & directed.

S&F in repair gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm bore complete all as specified & directed.

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

S&F, Supplying and laying of 20mm dai CPVC pipes SDR 11 & Plain CPVC SDR 11 with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

M & L for cutting chases for concealed water tubing, pinning in, making good of facings where required and pointing in cement mortar 1:3 to ends or edges etc, cutting not exceeding 10 cm width or girth, complete all as specified & directed.

S&F, in repairs, vitreous china wash basin, white, flat back of size 550mm x 400mm including brackets grouted in cement mortar 1:2 in wall complete all as specified and directed. including 32mm dia waste pipe with CP waste coupling pvc connection ,bracket etc in repair complete all as specified & directed.

S&F, in repair, bib taps, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed.

S&F in repair Fancy type brass chromium plated angle valve 15mm size complete all as specified & directed.

S&F in repair chromium plated fency pillar tape 15 mm dia complete all as specified and directed.

S&F, in repair, PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair PVC waste pipe for32/ 40mm bore pipe complete all as specified and directed by Engineer in Charge.

S&F, in repair, vitreous china wash down water closet pan (Pedestal pattern), white with 'p' or 's' trap (excluding flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc. complete all as specified and directed.

S&F in repair Plastic water closet seat, black / White, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified & directed.

S&F repair 10Ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified & directed.

S&F, in repair, CP Soap dish, any type, fixed to plugs with chromium plated brass screws and complete all as specified and directed

S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges and complete all as specified and directed

S&F in repair for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm longand complete all as specified and directed .

S&F in repair for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm diapipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repair Brass chromium plated shower rose 125mm size complete in all respect as specified.

S&F in repair PVC grating 100mm dia with waste pipe hole fixed to floor trap in repair and complete all as specified and directed.

Dismantling of cast iron ,PVC or reinforced concrete drain pipes, 75/110/150/200 mm dia, jointed in cement mortar and taking out of trenches, if required, Complete all as specified and directed by Engr-in-charge.

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed by the Engineer-in-Charge

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed .

S & F for Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed .The samples kept in the office of Engineer-in-Charge.

S & F 20MM Stainless steel decorated curtain rod with braket and ring complete all as specified and directed.

M&L for 50mm thick cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for laying 25mm thick PCC 1:2:4 type B-O, (using 12.5mm graded crushed stone aggregates) as in floor to receive topping layer complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) not exc 0.5 sq.m from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

S&F 3 mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane complete all as specified & directed.

M&L for 3mm thick figured glass, pin head type and glazing with oil putty in square not exc. 0.5 sq.m in each pane complete all as specified and directed.

S&F in repair, Kitchen sinks with drainage board made of stainless steel 1 mm thick with plugs washers and waster including beeding in cement mortar on to dwarf wall or influding fixing cantilever brackets and connecting union to pipe overall size 915mm x 460 mm bowl size 410 mm x 330 mm x 160mm, in repair, Complete all as specified and directed by Engineer-in-Charge.

S&F in repair, for Kitchen plate rack made of stainless steel 1 mm wall thickness with plugs washers as overall size of 75cm x 75 cm including fixing to wall and all assessaries in repair, Complete all as specified and directed by Engineer-in-Charge.

Dismantling asbestos cement (corrugated, semi-corrugated, etc) sheet in roof coverings complete all as specified & directed.

M & L 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc.all as specified and directed by engr-in charge.

M&L For Providing and fixing 10mm thick plaster of paris sunk or raised mouldingceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately complete all as specified and directed.

S&F for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surroundingwall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55mm thickness having kurledweb of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre tocentre. complete all as specified and directed .

S&F in repair vitreous china ware EWC combined pattern complete with internal fittings as specified and directed by Engineer-in-Charge. Make : Cera of Cat Part No S101314L or equivalent in Parryware / Hindware or equivalent make in PS

M&L for Double charge,vitrified tile 10mm thick (minimum), (square/ rectangular) polished, area of each tiles exceeding 0.36 Sqm (including 600mmx600mm size) but not exceeding 0.42 Sqm, in flooring set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and over and including 15mm thick screed bedding in CM (1:6) complete all as specified and directed.

S&F powder coated anodised aluminium windows sliding type (3 shutter type) with sash bars, aluminium sections weighing 0.55 Kg/mtr (minimum) incl stainless steel mosquito proofing wire mesh fixed with , clips, frame , necessary joining cleats, glazing clips, neoprene rubber gasket with aluminium beading screws suitable anodised fittings such as hinges, handles including powder coated anodised aluminium frame, grill with one or more rebates including S&F 5.50 mm thick black glass complete all as specified and directed.

M & L for Anodised aluminium Powder Coating (minimum thickness of powder coating 50 micron) frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

M & L for Anodised aluminium Powder Coating of Approved colour (Thickness or powder coating not less than 50 micron) sliding window and ventilator shutters, sliding (Two/Three) type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium and Sliding Arrangement Complete fittings as required complete all as specified.

S&F 15mm dia chromium plated fancy type wall mixer with over head shower for mixing hot & cold water screwed, fixing and connection to pipes complete all as specified and as directed. Make:- Cera Cat Part No F-1017401, Pearl Cat Part No ARI-015, Hindware Cat Part No- F-74 0022 or equivalent make in PS

S&F 15mm dia chromium plated fancy type sink mixer with swinging spout (wall mounted model) fixing and connection to pipes complete all as specified and as directed. Make:- Cera Cat Part No F 2004501, Pearl Cat Part No ARI-011, Hindware Cat Part No- F 330023 or equivalent make in PS

M&L for stone slab 30mm thick stone dressed true and square, in one length not less than 60cm and n. exc 120cm in copings, window cills, chajjas, sunshades, etc., punched dressed on exposed faces and self faced on the embedded unexposed beds and joints; exposed edges rounded or chamfered as directed, set, jointed and pointed in cement mortar 1:4 complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layer not exceeding 25 cm, soft lose soil complete all as specified & directed.

M&L for plain cement concrete in foundation feeling and mass concreate 1:2:4 type C-2 using (40 mm graded crushed stone agg) complete all as specified & directed.

Supply only MS galvanised chain link fencinng of 100x100mm mesh size and 4mm dia wire complete all as specified and directed.

Fixings only chain link fencing including line wires, any mesh, size and type to standards, rails, straininng bolts etc including provision of binding wire complete all as specified and directed. Note : supply only chain link fencing, MS 10mm dia round bars as line wire and MS flat iron shall be measured and paid separately under respective item of this schedule complete all as specified & directed.

S&F mild steel bolts. purpose made.with hexagonal orsquare head one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut. exc 10 cm but not exc 15 cm and 12mm dia complete all as specified and directed.

Supply only , round bars etc, in available length complete conforming to Fe-290 (Gde-165) complete all as specified and directed. Note 10mm dia mild steel round bars 2 Nos shall be provided horizently by interwewaving in the chain link and fixed with mild steel screw bolts with MS flat complete all as specified and directed.

S&F Mild Steel angle iron posts and struts in fencing (angle of size 65x65x6) mm including cutting tops to shapes as directed including driling holes for bolting of MS flat iron in horizontal, vertical & diagonal faces of each panel to be intertwined with Chain link fencing, and fixed to posts with MS nut, bolts and washers including all necessary drilling bolting etc, and similar work confirming to Fe 290 Gde E-165 complete all as specified and directed.

M & L for preparation of new or previously untreated steel surfaces of any description, n.exc 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer when unconnected with other painting or when painted in a different tint complete all as specified and directed.

M & L for repairing existing RCC structure work by gunting to damaged edge bottom of beam , chajja, slab 40 to 60mm thick and part of RCC member in CM 1:3 & depositing material/ mortar with spray gun under a pressure of 20 to 30 N/CM2 including skefolding and welding wire mess 2 mm dia and size of wiremesh 50mm X 50 mm including cutting welding and placeing position complete all as specified & directed by Engr in-charge.

M&Lfor sunken slab treatment comprising of the following :-(a) Taking out/ down old existing sunken slab treatment and cleaning the old RCC surfaces of sunken slab including removal of the rubbish from the site of work to a distance n.exc. 250mm compete all as specified and directed.(b) M&Lfor 25mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) over cleaned sunken slab surfaces.(c) M&Lfor applying bituminous priming coat/tack coat over PCC surfaces @ 0.30 Kg per square metre of surfaces. (d) M&Lfor applying bitumin grade 85/25 over priming coat @ 1.20 Kg per Square metre. (e) M&Lfor 25mm thick plastering in CM 1:4 using water proofing compound (WPC) @ 3% by weight of cement. on wall of sunken floor (f) M&Lfor suitable thickness of PCC 1:5:10 type E-2 (using 40mm graded broken brick aggregate) for filling in the sunken portion of slab up to its floor level.(g) Supply & fix of 32mm dia GI pipe medium grade, 450m long 9(for draining out the water) all as directed by engineer-in-Charge

S&F 15 mm dia brass chromium plated central hole wash basin mixture, fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut capstanhead screwed for 15mm dia pipe fixed in repair complete all as specified & directed.

M & L for Cleaning and removing all scale and dirt, etc. from tanks and from mouths of circulating pipes, etc of capacity upto 500 ltrs and endorsed the word "CLEANED ON" and "DATE" (in DD-MM-YY form) with stencil of letter size 10cm and refixing the float valve and plugging wash pipe complete all as specified and directed .

M & L for Cleaning and removing all scale and dirt, etc. from tanks and from mouths of circulating pipes, etc of capacity exc 1000 ltrs and upto & including 2000 ltrs and endorsed the word "CLEANED ON" and "DATE" (in DD-MM-YY form) with stencil of letter size 10cm and refixing the float valve and plugging wash pipe complete all as specified and directed .

BHAGWAN DAS & Co

Arun Construction Co.

vibha associates

M/S AMAR ELEKTRO CENTRE

Manglam Engineers and Construction Co

Punit Jain

Shikha Enterprises

mohanlal gupta

Tridev Construction Company