REPAIR TO LIFTS CHEQUER PLATE SIGN BOARD CEILING OTHER MISC REPAIR IN KABUL LINE PIRU VIHAR TIGRIS MOUDE KARAM VIHAR ARJAN VIHAR BIARD PLACE TODAPUR AND OTHER UNITS UNDER GE(U) PM DELHI CANTT10.

Amount

Section-I Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

Dismantling of structural steel work including doors, gates , framed truss etc complete all as specified and as directed.

Supplying and fixing Rolled section as in main and cross beams, hips and jack rafters, purline where connected to common rafters and running rails and guids for sliding doors fixed with angle cleats or other plates, conforming to Fe 290 grade E-165 complete all as specified and as directed.

Supplying and fixing of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS-1161(1979) grade ST-240 complete all as specified and as directed. (Make :- Surya Roshni Ltd./ Tata / Jindal)

Supplying and fixing of Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed. (Make:- Tata/ JSW/ Essar)

Supplying and fixing of Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed. (Make:- Tata/ JSW/ Essar)

Taking down granite (of any type) any thickness complete all as specified and as directed.

Material and labour for 20 mm thick black or any other colour granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like, set and pointed in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and as directed.

Material & Labour for 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and as directed.

Material & Labour for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and as directed. (Make:- Somany/ Johnson/ Kajaria)

Material & Labour for light shade or printed vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tile exc 0.36 sqm but not exc 0.42 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed. (Make:- Somany/ Johnson/ Kajaria)

Demolition of brick work or stone / boulder or concrete block masonry including all quoins, arches, pillars, etc. built in cement mortar complete all as specified and as directed.

Material & Labour for brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and as directed.

Demolition of reinforcement cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Material & Labour for precast reinforced cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in cover in drain, manhole cover, plateform etc complete all as specified and as directed.

Material & Labour for RCC 1:1½ :3 type A1(using 20 mm graded stone aggregate) as in foundations, footings, plinth beams; bases for columns, etc.complete all as specified and as directed.

Material & Labour for RCC 1:1½ :3 type A1(using 20 mm graded stone aggregate) as in Column, pillars, piers, posts and struts etc complete all as specified and as directed.

Material & Labour for formwork to sides of concrete in foundations, footings, bases of columns, sides and soffits (if any) plinth beams, and similar work complete all as specified and as directed.

Material & Labour for formwork to sides of concrete of pillars, posts, struts, piers, columns etc complete all as specified and as directed.

Supplying and fixing Mild steel TMT bars of 10 mm dia and over cut to length bent to shape required including cranking, bending etc and S&F for stengthening existing reinforcement by use of mild steel bars of any dia , cut to length, bent to shape required, including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and labour for TMT bars 6 to 8 mm dia for reinforcement cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, and binding with and incl MS wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-415 or Fe-500 complete all as specified and as directed.

Taking down cement or cement lime plaster any description on any walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Material & Labour for Rendering 15 mm thick on fair faces of brick work or concrete surface in CM (1:6), finished even and smooth without using extra cement complete all as specified and as directed.

Material & Labour for rendering 15mm thick in cement mortar 1:4 on concrete/Brick surfaces, chajja or projections finished even and smooth without using extra cement complete all as specified and as directed.

Material & Labour for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over one coat of alkali resistant primer complete all as specified and as directed. (Make:- Nerolac/ Jenson & Nicholson/ Asian Paints/ Berger Paints)

Material & Labour for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over one coat of chalk whitening complete all as specified and as directed. (Make:- Jenson & Nicholson/ Berger Paints/ Asian Paints)

Taking down door/window frames with shutters exc 1.50 sqm but not exc 4.00 sqm each (without taking off shutters from frame) complete all as specified and as directed.

Supplying and fixing powder coated aluminium frame for doors, windows, ventilators and sliding tracks, beading for grill with one or more rebates including joining cleat for fixing etc. complete all as specified and directed (min thickness of powder coating 50 micron).complete all as specified and as directed. (Make:- Jindal/ Indal/ Hindalco)

Supplying and fixing anodised aluminium door/window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed. (Make:- Jindal/ Indal/ Hindalco)

Supplying and fixing of steel window with side hung shutters including box type hinges with steel handle, hold fast and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

Supply and fixing sheet glass ordinary quality 5.5 mm thick type fixed to aluminium doors in squares n.exc 0.5 sqm in each pane complete all as specified and as directed. (Make:- Saint Gobain/ Modiguard/ Triveni Float Glass)

Supplying and fixing in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples and wooden beads upto four storied of building complete all as specified and as directed.

Supplying and fixing 4 mm th Sheet glass, ordinary quality and glazing with oil putty in square in any size n.exc 0.5 sqm complete all as specified and as directed. (Make:- Saint Gobain/ Modiguard/ Triveni Float Glass)

Demolition of cement concrete of any description and in any position complete all as specified and as directed.

Material & Labour for plain cement concrete (1:2:4) type B-1 using (20 mm graded crushed stone aggregate) as in levelling course/base padding,complete all as specified and as directed.

Material & Labour in repairs for 15 mm bore Chromium plated fancy type Bip taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. (Make:- Jaquar/ Kohler/ Marc/ ESS ESS)

Material & Labour in repairs for 15 mm dia Fancy type Chromium plated Angle valves, cast copper alloy screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. (Make:- Jaquar/ Kohler/ Marc/ ESS ESS)

Supplying and fixing in repairs PTMT 32mm dia waste coupling (half or full threaded), minimum weight 60 gms) fixed to stainless steel sinks complete all as specified and as directed.

Supplying and fixing in repairs for 125mm dia PTMT grating doom with waste hole for waste pipe ( minimum weight 40 gram) complete all as specified and as directed.

Supplying and fixing in repairs for 450mm long CP brass connection pipe with CP brass nuts on both ends for fixing to pipe or other fittings complete all as specified and as directed.

Supplying and fixing in repairs for PVC waste pipe 32/40mm bore fixed to PTMTwaste coupling for kitchen sink complete all as specified and as directed.

Supplying and fixing in repair for vitreous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed. (Make:- Cera/ Hindware/ Parryware)

Supplying and fixing in repairs PVC valveless, syphonic action type, flushing cistern, low level, white with inlet ball valve foat and handle including brackets 10 litres complete all as specified and as directed. (Make:- Cera/ Hindware/ Parryware (1st Quality)

Supply and fixing in repairs viterous China wash basin, white flat back, size 550x400mm excluding taps, waste chain and plug and porcelan stopper but including brackets complete all as specified and as directed. (Make:- Cera/ Hindware/ Parryware (1st Quality)

Supplying and fixing in repairs for 15 mm bore brass CP wash hand basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed. (Make:- Cera/ Hindware/ Parryware (1st Quality)

Material & Labour for 75 mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in complete all as specified and directed.

Material & Labour for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. (Make:- Asian Paints/ Nerolac Paints/ Berger Paints/ Jenson & Nicholson Paints)

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Material & Labour for 100mm thick cement concrete type B-2, 1:2:4 (40 mm graded stone aggregate) as in hard standing and footpaths complete all as specified and as directed.

Material & Labour for 25mm thick cement concrete type B-1, 1:2:4 (20 mm graded stone aggregate) as in finishing cement concrete surface even and smooth (without using extra cement) complete all as specified and as directed.

Material & Labour for cement concrete type D-2 1:4:8 (using 40 mm graded stone graded stone aggregate) as in sub base for tiling complete all as specified and as directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed.

Section-II Supply and fixing in repair of TCB to LCB II Kit along with all connected accessories complete suitable for 08 Passenger lift (make of lift M/s OTIS Elevator Co. India Ltd.), as per site requirement including taking down old unserviceable one complete all as specified and as directed. (Make :- As per OEM recommendation).

Supply and fixing in repair of AT 120 door operator to LEDO operator along with all connected accessories complete suitable for 08 Passenger lift (make of lift M/s OTIS Elevator Co. India Ltd.), as per site requirement including taking down old unserviceable one complete all as specified and as directed. (Make :- As per OEM recommendation).

Taking down and supply & fixing in replacement of Car door track & roller kit as per sample suitable for 08 passenger lift (make of lift M/s OTIS Elevator Co. India Ltd.) complete all as specified and as directed. (Make- As per OEM Recommendation)

Taking down and supply & fixing in replacement of Landing door track & roller kit as per sample suitable for 08 passenger lift (make of lift M/s OTIS Elevator Co. India Ltd.) lifts complete all as specified and as directed.

Taking down and supply & fixing in replacement of Logic control Board (LB II ) Kit for VF Controller as per sample suitable for 08 passenger lift (make of lift M/s OTIS Elevator Co. India Ltd.) complete all as specified and as directed. (Make- As per OEM Recommendation)

Taking down and supply & fixing in replacement of Door Moter 9550 operator as per sample suitable for 08 passenger lift (make of lift M/s OTIS Elevator Co. India Ltd.) complete all as specified and as directed. (Make- As per OEM Recommendation)

Taking down and supply & fixing in replacement of Drive Interface Board Panel (DIB)as per sample suitable for 08 passenger lift (make of lift M/s OTIS Elevator Co. India Ltd.) complete all as specified and as directed. (Make- As per OEM Recommendation)

Supply and fixing in repair for unit 2-07-S9490 per sample suitable for 08 passenger of M/s TK Elevator India Pvt. Ltd. (formerly known as M/s Thyssenkrupp Elevator India Pvt Ltd.) with following items complete all as specified and directed 1.1000043228 Inverter Tke-1-18.5 7.5Kw Ol/Cl - 1.00 Nos 2.1000043229 Inverter Tke-1-24.5 11Kw Ol/Cl - 1.00 Nos 3.1000043284 Inv K200 Door Ty-Bg101-S20P4A Bst_Black - 2.00 Nos 4.1000043289 Inverter Cpic-1-18 7.5Kw - 1.00 Nos 5.1000043290 Inverter Cpic-1-27 11Kw - 1.00 Nos 6.1000043501 Smps D-60B 24V1.8Amp 5V3Amp Tic-Iv - 2.00 Nos 7.1000043559 Pcb Mpus R2 Smd Version Tic Ii - 2.00 Nos 8.1000043616 Pcb Mcu Motherboard Tic V - 3.00 Nos 9.1000043830 Pcb Ctu Tic-V - 2.00 Nos 10.1000043831 Pcb Ccu Scrolling Tic-V - 2.00 Nos 11.1000044206 Contactor Lc1D18F7 110Vac - 4.00 Nos 12.1000044208 Contactor Lc1D25F7 110Vac - 4.00 Nos 13.1000044279 Contactor Lc1D12F7 110VAc_Local - 4.00 Nos 14.1000044976 Rectifier Bridge Kbpc3510 - 2.00 Nos 15.1000045941 Motor Door Header V3F 0.25Kw 6P - 1.00 Nos 16.1000067401 Encoder Houde Htb-30L24G 10-30F 1024B-S8 - 2.00 Nos 17.1000067521 Motor Pmsm 125St-13 K300 Co/2 47W Ip44 - 1.00 Nos 18.1000084700 IR 957B61-AC220V CABLE 3.5 MTR PS WECO- 2.00 Nos 19.1000103514 DOOR INVERTER BG221-BS21E BST -1.00 Nos

Material & Labour for painting of Car cabin,Car door,landing Door,Door frame,False ceiling of 13 Passenger Lift with two coats synthetic enamelled as existing paint also where black paint is required as per direction of Engr-in-Charge after scratching the old paint and preparing smooth surface suitable for painting complete all as specified and as directed. (Make of paint:- ASIAN/ BERGER/ JHONSON & NICHOLSON/ SHALIMAR)

Supply and fixing in repair of Co2 type fire extinguisher as stored pressure of capacity of 0.500 Kg complete all as specified and as directed. Make- ceasefire

Notes :- ( for Item 54 to 61) (i) The repair work shall be done through OEM of existing lifts i.e. of M/s OTIS Elevator Co. India Ltd., M/s TK Elevator India Pvt. Ltd. (formerly known as M/s Thyssenkrupp Elevator India Pvt Ltd.) (ii) The contractor will have to submit MOU on stamp paper of Rs 100/- duly notarized, as per specified Performa given on Particular Specification page No. 126 & 127 from OEM's of existing lifts within 15 days from date of Acceptance of tender, failing which the contract will be liable to be cancelled and further action to be taken as per policy in vogue of the contractors default.

Comprehensive maintenance of installed lift in reliable safe and efficient operating condition through MOU with respective OEM of existing lift M/s Schindler India Pvt. Ltd by regularly examining, lubricating and adjusting the equipments and carry out planned maintenance in systematic and controlled manner suitable for serving Basement + ground floor i.e. total Five landings with electric power operated doors, auto electric levelling device installed complete all as specified and as directed. Location : HQ DGBR :- Adm building Total lifts : 01 Nos Capacity : 16 Passenger Make :- M/s Schindler India pvt Ltd. (Note:- tine duration -29 Aug 2023 to 28 Oct 2023 (02 months)

Note for item No 65: - (i) The above maintenance shall be done through OEM of existing lifts.Please also refer PS Page No. 121 & 122. (iii) The contractor will have to submit MOU through OEM of exising lifts as given on Particular Specification Page No 123 to 125 from M/s Schindler India Pvt. Ltd. within fifteen days of acceptance of tender, failing which the contract will be liable to be cancelled and further action to be taken as per policy in vogue. (iv) Contractor will conclude AMC for contract with OEM, M/s Schindler India Pvt. Ltd Platinum Agreement of existing lifts and copy of the agreement and alongwith invoice copy will be submitted to Engineer-in-Charge and GE before commencement of AMC. No payment will be made to contractor without submission of valid AMC agreement. (v) The above maintenance include complete maintenance of existing lift by regularly and systematically examining adjusting fabricating as required for smooth and efficient functioning of the equipment/ lift. (vi) Contract included of repair replacement of machines, motors, generators, ropes, inverter/ ARD system, controller parts, PCBs, belts, rollers, gears, bearings, solenoids, coils, chock brake shoes, liners, contactors, relays, coils, pushbuttons, door operator VVF drive,VVVF main drive,cardoor safety device limit switches,governor,hoistway door locks,indicators and other minor machanical parts shall also be included the cost shall deemed to be included in the rates quoted by the contractor

(vii)The following items are not included : replacement of car cabin, ceiling frames, panels, hoist way, door panels, door frames, sills, car flooring, floor covering, lighting fixtures, ceiling light bulbs and tube, main line power switches, breakers, feeders to controller, hoist way wiring, hydralic jack outer casing, burried piping, alignment of elevator guide rails,smoke and fire sensors, communication devises, security systems, landing doors,sheave rim,hoist rope & ARD battery and cabin fans. (viii) The OEM will also detail one technican staff to inspect the lifts every week, regarding its functioning operation or any other issue arising in the lift. the problem noticed if any to be addressed immediately. in case no technician is detailed Rs 500/- per week per lift will be deducted from the payment. Technician should always carry service tool along with himself during each weekly visit. (ix) OEM will also arrange housekeeping staff for proper cleaning of lift shaft, lift pit, Car top and machine room at least on monthly basis. (x)Contractor to note that monthly service will not be paid for the building undergoing special repairs/ unoccupied buildings and no penalty shall be imposed upon contractor, or all as per direction of Engr-in-Charge. (xi) All existing earthing of the lifts shall be maintained and made fully functional by the contractor to the entire satisfaction of the Engr-in-Charge

M/s Dhapola Elevator and Engineering

J D ENTERPRISES

M P TYAGI ENGINEERS AND CONTRACTORS

CUCKOO ENTERPRISES