Construction of 3 BHK Residential Quarters 12 sets including sanitary fittings and internal electrification at FVSc and AH Campus RS Pura

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead up to 50 m and lift upto 1.5 m

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level.

1:3:6 (1 Cement : 3 coarse sand(zone-III) : 6 graded stone aggregate 20 mm nominal size) (using 30 % boulders including cost and carriage of boulders).

1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size)

Making plinth protection 50 mm thick of cement concrete 1: 3: 6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm nominal size well ramed and consolidated and grouted with fine sand including finishing the top smooth

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- All work upto plinth level.

1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness). Including attached pillasters, buttresses, plinth and string courses fillets columns, pillers, piers, abutments, posts and struts etc. upto floor 5 level exclusing cost of centring shuttering, finishing and reinforcement.

1:1.5:3 (I cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Centring and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access platform.

Shelves (Cast in situ).

Lintels, beams, plinth beams, girders, bresumers and cantilevers.

Columns, pillars, piers, Abutments, posts and struts

Stairs, (excluding landings) except spiral-staircases.

Edges of slabs and breaks in floors and walls.

Under 20 cm wide

Weather shade, Chajjas, corbels etc., including edges.

Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete

Cold twisted bars/ mild steel and MT steel

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Brick work with FPS bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1: 6 (1 cement: 6 coarse sand)

Extra for brick work in superstructure above plinth level upto floor V level.

Half brick masonry with FPS bricks of class designation 75 in foundations and plinth in:

Cement mortar 1: 4 (1 cement: 4 coarse sand)

Extra for half brick masonry in superstructure above plinth level upto floor V level

Extra for providing and placing 2 Nos. 6 mm dia M.S. bars at every third course of half brick masonry (with FPS bricks)

Tile brick masonry with common burnt clay F.P.S. (non modular) tile bricks of class designation 10 in superstructure above plinth level up to floor V level in cement mortar 1:6 (1 cement : 6 coarse sand).

Providing and fixing 18 mm thick gang saw cut, mirror polished, pre moulded and prepolished machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1: 4 (1cement: 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. Complete at all levels.

Granite of any color and shade (Area of slab over 0.5 sqm)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia. & length (hold fast lugs or dash fastener shall be paid for separately).

Sal wood

Providing 40x5 mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts, nuts, and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 (1 cementn:3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to steel windows by welding.

Steel work welded in built up sections / framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc as required.

In grating, frames, guard bar, ladders, railings,brackets, gates and similar works

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing 1st quality ceramic glazed tiles conforming to IS: 13753 of minimum thickness 5 mm of approved make like NITCO, ORIENT, SOMANY KAJARIA, or equivalent make in all colours, shades except begundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1: 3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3 KG per sqm including pointing in white cement mixed with pigment of matching pigment etc., complete. (wall tile)

Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

10cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25mm thick mud mortrar mixed with bhusa at 35 Kg per cum of earth and gobri leaping with mix 1:1 (1 clay :1 cow dung) and covered with flat tile bricks of class designation 100 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement adn finished neat

With FPS brick tiles

Providing gola 75 x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down guage) including finishing with cement mortar 1:3 ( 1 cement :3 fine sand) as per standard design.

in 75 x 75 m deep chase

Making Khurras 45x 45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20mm nominal size) over P.V.C sheet 1m x 1m x 400 micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating .

12 mm cement plaster of mix :

1:6 (1 cement: 6 coarse sand)

15mm cement plaster on rough side of single or half brick wall of mix (upto 10mt. Ht.)

1:6 (1 cement :6 coarse sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) finished with a top layer 6mm thick cement plaster 1:6 (1 cement: 6 fine sand).

6 mm cement plaster to ceiling of mix

1: 3 (1 cement: 3 fine sand)

12 mm thick plain cement mortar bands in cement mortar 1:4 (1 cement: 4 fine sand) :

Raised Band

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade.

New work (two or more coats) over and including water thinnable priming coat with cement primer.

Applying priming coat :

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Renewing glass panes and refixing existing wooden fillets in aluminium frames.

Float glass panes of thickness 5.0 mm .

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : Make( Hindware/Jaquar/Cera/Plumber/Parryware)

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. Make( Hindware/Jaquar/Cera/Plumber/Parryware)

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Make( Hindware/Jaquar/Cera/Plumber/Parryware)

Flat back wash basin of size 550x400 mm.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe

32 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminum angle frame with CP brass brackets and guard rail complete fixed with 40mm long screws, rawl pluggs etc. complete

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

15 mm dia. nominal bore

20 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

25 mm dia. nominal bore

65 mm dia. nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

20 mm nominal bore

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5.0 mm thickness

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/ stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 ltr/sqm. by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/ltr and viscosity 70 -160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete.

The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C.Cold flexibility shall be upto -2°C when tested in accordance with ASTM,D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacture of membrane.

3 mm thick

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.

Second class deodar wood

35 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:

12 mm thick ply board panelling (water proof)

Providing and fixing 35 mm thick wire guage shutters using galvanised MS wire guage of average width of aperture 1.4mm with wire of dia 0.63 mm for doors including ISI marked bring finished or / and black enamelled M.S.butt hinges with necessary screws and polishing the shutter complete.

second class Deodar wood

Providing and fixing wire gauge in aluminium shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire gauge of dia 0.63 mm in doors/windows.

Providing and laying stone soling work including carriage and stacking etc. including filling of interstices/gaps by crushed aggregate/sand etc. complete item.

Supplying and laying of lime mixed with soil in (1:15) mix below stone soling including consolidation in two layers of 100 mm thick each including compacting with roller complete

Finishing walls with weather proof exterior paint of required shade New work (two or more coats) over and including priming coat complete.

Providing and fixing of steel almirahs of size = 3'-0"x2'-0"x8'-0", using 18 guage sheet with Godrej or equivalent locks, looking glass and accessories complete item including placing in position

Providing and fixing of the following sanitary items with necessary fittings complete item

Soap dish of nominal size (CP) Make( Hindware/Jaquar/Cera/Plumber/Parryware)

PVC connection

CP gratings (100 mm)

CP long body bib cok of approved make (15 mm nominal bore) Make( Hindware/Jaquar/Cera/Plumber/Parryware)

CP short body bib cok of approved quality (15 mm nominal bore) Make( Hindware/Jaquar/Cera/Plumber/Parryware)

Stainless jali with or without holes for floor trap, 100 mm dia, wt. not < 100 gm

C.I. waste coupling 30 mm of 79 mm length x 77 mm breadth

Providing & fixing C.P. cup complete

Providing & fixing Jet for seats. Make( Hindware/Jaquar/Cera/Plumber/Parryware)

Providing & fixing wall mixer L-bend of nominal dia and approved make (bathroom)

C.H. mixer of nominal dia & approved make (wash basin) Make( Hindware/Jaquar/Cera/Plumber/Parryware)

Shower (15mm nominal bore)Make( Hindware/Jaquar/Cera/Plumber/Parryware)

CP Towel Ring Make( Hindware/Jaquar/Cera/Plumber/Parryware)

CP Towel Rod Make( Hindware/Jaquar/Cera/Plumber/Parryware)

Stainless Steel Double Bowl Kitchen Sink (45"x20"x8") Make( Hindware/Anupam/Cera/Jindal/Parryware)

CP Angle Valve (15 mm nominal bore) Make( Hindware/Jaquar/Cera/Plumber/Parryware)

Providing and fixing of the following G.I. accessories/fittings and making G.I. connection with manholes.

25 to 40 mm nominal bore

32 to 50 mm nominal bore

15 mm to 20 mm nominal bore

Gate valve (2")

Providing and fixing check valve (3/4")

Providing and fixing followong PVC items ( Make:-Supreme/Prince/Astral/Finolex)

PVC pipe (150 mm dia)

PVC pipe (110 mm nominal dia)

PVC pipe (75 mm nominal dia)

PVC pipe (40 mm nominal dia)

PVC plain bend (110 mm)

PVC plain bend (75 mm)

PVC plain bend (40 mm)

Door bend (110 mm)

Door bend (75 mm)

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete

900 mm x 750 mm

Small size = 300 mm x 300 mm

Providing and fixing in position PVC water tank of Sintex or Equivalent brand with lockable cover including connection of inlet-outlet over flow and cleaning pipes including cost of GI pipe , G.I fittings complete item of nominal capacity

Providing and laying river bed material comprising of sand , stone boulders, earth etc. complete including consolidation, watering, carriages, loading and unloading etc

Providing & laying in position cement concrete (1:5:10) mix using 40 mm nominal size brick aggregate complete item.

Diluting and injecting chemical emulsion for pre-constructional Anti-termite treatment complete job including material and labour.

Providing and fixing of the following accessories including necessary nails and screws complete

Aluminum alloy Handles

Aluminum Tower bolts

Aluminum Arle

Door stopper

Door closer

Godrej Mortise door handle with lock

Door/Wall Hook hanger

providing and fixing in position of curtain rods of MS pipe with PVC cover of approved brand and manufacture shade and colour with necessary screws etc. complete with globes and rings

Forming groove of uniform size from 12x12mm and upto 25x15mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge.

Providing and fixing of aluminium lock handle in sliding aluminium windows complete.

Providing and fixing welded wire mesh incuding primer coat.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

SUB-DISTRIBUTION BOARDS

Providing and fixing 6 amps to 32 amps rating 240 volts, 'L' series, miniature circuit breaker of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as reqired (category B)

Single Pole - 6 to 32 A

Supply and fixing of following rating, 2P 230 volts, SPN in the existing MCB DB complete with connections, testing and commissiong etc. as required

40 amps SPN

63 amps SPN

EARTHING AND LIGHTNING PROTECTION

Earthing with GI earth plate 600mm x 600 mm x 6mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) complete as required for earthing and lightning protection.

Providing and fixing 25 mm x 5mm GI strip from earth electrode as required

DISTRIBUTION BOARD

Supply, installation, testing at works, installation and commissioning of following distribution boards totally enclosed compartmentalized, cubicle indoor type fabricated with 16 SWG sheet steel, with Aluminium bus bars (both for main and neutral bus bars), complete with following switchgear/ mountings cable terminations, inter-connections as required, for 415 volts, 3 phase, 4 wire 50 HZ AC supply as per specifications and drawings.

Moulded case circuit Breakers shall be thermal magnetic trip type. Fault level for all MCCB and bus bar shall be 35 KA. ICU shall be equal to ICS=100%

All metering current transformers shall be Class 1, 15 VA.

MDB-1 (Indoor Type)

Incomer

160 A 4P MCCB – 1No.

R,Y,B phase indicating lights with control fuses - 1 set

Bus Bar

200A 415V, 50Hz, 3ph, 4 wire Aluminium Bus bar

Outgoing

40 Amp 2P SPN - 5No.

63 Amp 2P SPN - 10 No.

LT CABLES

Supply and laying of PVC Power cable 1.1 KV Grade armoured aluminium XLPE cables including earth work, cost of end termination, thimbles and saddles etc. as required.

3.5C x 120 sq.mm

SUB-DISTRIBUTION BOARDS

Supply and fixing of the following way, single pole and neutral / three pole and neutral, sheet steel, double door, phase segregation type, MCB distribution board, 230V / 415V on surface/recess, complete with tinned copper bus bar, neutral bus bar and link, earth bar, din bar, detachable gland plate, interconnections, including painting, earthing, etc., as required.

8 way TPN

6 way TPN

4 way TPN

12 way SPN

Supply and fixing 1x20 watt box type fitting complete with extruded alulminium tube rod including connection testing etc. as reqd. (CAT No. DMLNLT8-16 and LTT8-20)

Supply and fixing of 18 Watt LED Panel surface mounted including connection testing etc as reqd. (CAT No. LCDSPLN-R-18-CDL)

Supply and fixing of 9 Watt LED mirror light 2' long including connection testing etc as reqd. (CAT No. LCTL-09-CDL)

Supply and fixing of 70 Watt LED street light on the existing with GI pipe bracket with all accessories including connection testing.

Wiring for telephone point with 0.61 mm dia copper conductor unarmoured shielded twisted telephone wire in 25mm dia existing PVC conduit, connections etc. complete as required as per specification and drawings.

Supply and fixing telephone socket outlet housed in zinc passivated box with suitable connector strip in recessed wall / partitions as required

WIRING

Wiring for light / fan / exhaust fan / call bell point with 1.5 Sq mm FR PVC insulated copper conductor cable in surface / recessed ISI marked PVC conduit(2mm thick) including concealed box 6 inch and providing 5 amp switch and earthing complete as required.

Light point on board with copper wiring in ISI marked PVC conduit wiring for 3 Pin 6 amp plug point with 1.5sqmm PVC insulated multistrand copper conductor cable including P/F of 3 Pin 6 amp socket outlet on switch board in surfaced recessed PVC conduit wiring system and 6 amp switch, earth the 3 pin as required with 01 No. PVIC insulated green colour wire.

Wiring for light plug with 2 x 2.5sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked PVC conduit along with 1x 0.75 mm copper wire for loop earthing required

Wiring for power plug with 2 x 4 sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked PVC conduit along with 1x0.75 Sq mm copper wire for loop earthing as required

Wiring for power plug with 2 x 1.5sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked PVC conduit along with 1x1.5 Sq mm copper wire for loop earthing as required

Wiring for 1x 1.5sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked in the existing PVC conduit etc. as required ( Invertor wiring )

Wiring for sub main wiring with following sizes of PVC/ insulated copper conductor wires in the surface/ recessed PVC / MS conduit along with PVC insulated copper conductor earth wire as required complete with connections, testing and commissioning etc. as per specifications and drawings.

2x6 sq mm with 1x6.0sqmm earth wire

2x10sq. mm with 1 x 6.0sq. mm earth wire

Wiring for sub main wiring with4x10 sqmm alongwith 2x6sqmm earth wire sizes of PVC/ insulated copper conductor side core conductor in surface/recessed PVC conduit etc. as reqd.

Wiring for twin control light point with 2x1.5 sq. mm PVC insulated copper conductor cable in surface / recessed ISI marked PVC conduit with 2 way 6 Amp switch

Supplying and fixing metal box of 180 x 100 x60mm deep in recessed with suitable size phoenolic laminated sheet cover in the front including providing and fixing 3 pin 15Amp socket outlet and 15Amp switch connections, painting etc. as required. (Power plug)

Supply and fixing of 250 mm x 300 mm x 100 mm deep size metal box with suitable size phenolic laminated sheet cover in the front including connection testing etc as reqd.

Supply and fixing of 200 mm x 300 mm x 100 mm deep size metal box with suitable size phenolic laminated sheet cover in the front including connection testing etc as reqd.

Supply and fixing step up electronic fan regulator on the existing switch box including connecting testing etc. as required.

Supply & fixing of 10 sqmm x 2 core aluminium armoured PVC cable suitable for 1.1 KV grade including cost of end termination, connection testing etc. as reqd.

Supply and fixing of wall bracket suitable for 230 volts complete with 15 watt LED including connection testing etc as reqd.

Supplying and fixing of exhaust fan 300mm sweep heavy duty trans air with double ball bearing including connection, texting etc. as required.

Supply and fixing Call bell / buzzer DC / AC single phase 230 V complete

Supply and fixing 20 Amp Industrial socket with 32 Amp SPN including connection, testing, etc. as required

Supply and fixing of 63 Ampere TPN in the existing Distribution board including connection testing etc as reqd.

Supply and fixing 2 Hp single phase monoblock pump set covered with shed of suitable size made of 16 SWG MS sheet including its painting and with small outdoor panel with bus bar 32 TPN with single phase starter including testing commissioning etc. required

Supply and fixing of 25 mm dia PVC conduit alongwith accessories in surface/recess.

Supply and fixing of 32 mm dia PVC conduit alongwith accessories in surface/recess.

Supply and drawing of co-axial TV cable RG-6 grade, 0.7mm solid copper conductor PE insulated , shielded with fine tin copper braid and protected with PVC sheath in the existing / recessed PVC conduit

Erection of SST poles in cement concrete pedestal 1:3:6 including excavation foundation (1:4:8) centering and shuttering of poles by engaging skilled labour with long rope complete job including cost of cement and carriage of pole from store to site.

Supplying and fixing of Mukki Clamp complete with nut, bolt etc. as reqd.

Supplying and fixing of U-Clamp alongwith 4" in size Shekel insulator with 6" long G.I. nut bolt complete job.

Supplying, laying, stringing and binding of LT conductor (Rabbit)

Supplying, laying, stringing and binding of LT conductor (weasel)

Supplying and fixing of stray rod complete with all accessories including digging of pit and refilling it with cement concrete (1:3:6) complete job including cost of cement.

M/s Kanhaiya Constructions

KAPAHI CONTRACTS PRIVATE LIMITED

MOHD IDRIS SHAN

ASHOK KUMAR SHARMA

Mohan Lal Gupta and Sons

M/S MAGOTRA ENGINEERS and CONTRACTOR

Ghulam Mohammad Bhat

M/s Romesh Construction Co

vijay builders