Repair and maint of wooden and steel furniture under AGE (I) CIF (K)

Amount

Repairing of old unserviceable/ broken parts of Charpoy GI pipe plytop and S&F/M&L follwing new parts/work all as per drgs and specified or directed by Engr-in-Charge: - as under: - (DRAWING NO. FD-220/FD/MAP-II/01)

Removing of old unserviceable/broken plywood from Charpoy GI pipe, S&F new 12mm thick commercial plywood BWR Grade, ISI Marked over exisiting Charpoy GI and tightened with 12 Nos new screws after necessery welding work of iron strips wherever required duly completed alongwith following repair work shown all as per drgs and directed by Engr-in-charge.

Removing old unserviceable/broken GI long rails from charpoy pipe, S&F new size long rails of 32mm GI pipe medium grade, ISI marked duly new threaded on both sides including two nos 32mm GI check nuts all as per drgs.

Removing unserviceable/broken short rails of charpoy GI pipe, cutting and fixing short rail from retrieved old long rails as per ser No 1.02 above, duly threaded both ends complete all as per drgs.

Removing old broken legs of charpoy GI, cutting and fixing legs from retrived old long & short rails as per item ser No 1.02 & 1.03 above duly threaded one end with fixing of hardwood plug at bottom of legs all as per drgs.

Removing unserviceable/broken elbow of charpoy GI pipe and S&F new GI Elbow 32mm dia 03 way, ISI marked all as per drgs.

Repair of old unserviceable/ broken parts of Bed Plytop (1980x900mm)/IP and S&F/M&L following new parts/work all as per drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-246/FD/06/MAP/08(R))

Removing old unserviceable/broken ply top from bed plywood/IP, S&F new 12mm th commercial plywood BWR grade, ISI marked over existing bed duly completed alongwith following works all as per drgs.

Removing old unserviceable/broken head rest from bed ply, S&F new head rest made out of 4mm teak ply facing both side alongwith 22.TH soft wood batten with 12mm half cut TW beading duly french polished complete with following works all as per drgs.

All description as per item No 2.02 above but foot rest.

Removing old unserviceable/broken long rail from bed & S&F new long rail frame of 35x90mm made out of 1st class teakwood duly french polished all as per drgs.

All description as per item No 2.04 above but short rail.

All description as per item No 2.04 above but stiffners (40x60mm) to support plywood.

All description as per item No 2.04 above but legs made out of 400x60x60mm size all as per drgs.

Repairing old unserviceable/broken parts of CHAIR DINING and S&F/M&L following new parts/work all as per drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-228/279)

Removing old unserviceable/ broken plastic cane from chair dining, S&F new plastic cane of 2mm size and canning (Godrej pattern) to chair seat alongwith new wooden member screwed to side frames for canning on each side, duly completed all alongwith following repair/polish work. S&F new 4 nos hard rubber ring duly screwed at bottom of leg all as per drgs.

Removing old unservicceable/Broken rear legs from chair dining, S&F of new legs made out of 1st class teakwood duly french polished till gloosy shining to complete surface all as per drgs.

All description as per item No 3.02 above but front leg.

All description as per item No 3.02 above but back rail.

All description as per item No 3.02 above but front rail.

All description as per item No 3.02 above but side rail.

All description as per item No 3.02 above but stiffener.

Removing old unserviceable/ broken parts of CHAIR EASY and S&F/M&L following new parts/work all as per drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-229/281)

Removing old unserviceable/broken plastic cane from chair easy, S&F new plastic cane of 2mm size and canning (Godrej pattern) to chair seat & back alongwith new wooden member screwed to side frames for canning on each side, duly completed all alongwith following repair/polished work. S&F new 4 nos hard rubber ring duly screwed at bottom of leg all as per drgs.

Removing old unserviceable/broken rear legs from chair easy, S&F of new rear legs made out of 1st class teakwood duly french polished till gloosy shining to complete surface all as per drgs.

All description as per ser item No 4.02 above but front legs.

All description as per ser item No 4.02 above but front frame.

All description as per ser item No 4.02 above but back frame.

All description as per ser item No 4.02 above but side frame.

All as per ser item No 4.02 above but arms.

Removing old unserviceable/ broken parts of TABLE BED SIDE and S&F/M&L following new parts/work all as per drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-276)

Removing old unserviceable/ broken top of table bed side, S&F new top made out of 18/19mm thick MDF/prelaminated particle board of teak veneered outside with 4mm thick teak wood edging alround duly french polished alongwith following works all as per drgs.

All description as per ser item No 5.01 above but sides support of table all as per drg.

Removing old unserviceable/ broken shelves of table bed side, S&F new shelves made out of 12mm thick med density fiber board/particle board with teak veneered top ISI marked complete all as per drgs.

Removing old unserviceable/ broken back side ply wood of table bed side, S&F new back side made out of 6mm thick ply wood commercial ISI marked complete all as per drgs.

Removing old unserviceable/ broken parts of TABLE 3'x2' with/without drawer and S&F/M&L the following new parts/work all as per drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-283/284).

Removing old unserviceable/ broken table top, S&F new top of 18/19mm thick MDF/pre-laminated particle board of one side teak face exterior grade, ISI marked screwed so long from top rail including 04 mm thick 1st class teak wood beading duly french polished alongwith following works. S&F 4 nos new hard rubber ring screwed at bottotm of legs complete all as per drgs.

Removing old unserviceable/ broken legs from table, S&F of new legs made out of 1st class teakwood duly french polished till gloosy shining to complete surface all as per drgs.

All description as per ser item No 6.02 above but Long rail.

All description as per ser item No 6.02 above but short rail.

All description as per ser item No 6.02 above but stiffner.

All description as per ser item No 6.02 above but drawers with decorative knob.

Repair to old unserviceable/ broken parts of TABLE WRITING and S&F/M&L the following new parts/work all as per drgs drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-268/275)

Removing old unsv/broken top of table writing, S&F new top made out of 18/19mm thick MDF/pre-laminated particle board one side teak face, exterior grade, ISI marked with 4mm thick 1st class teak wood beading alongwith following work all as per drgs.

Removing old unsv/broken drawer of table, S&F new drawer made of 12 th planks with bottom of 6mm thick plywood, wooden bearer with new recessed handle to drawer all as per drgs.

All as per ser item No 7.02 above but alongwith new locking arrangement and new recessed handle.

Removing old unsv/broken legs of table, S&F new leg made out of 1st class hard teakwood, duly french polished.

All description as per item No 7.04 above but top front long rail.

All description as per item No 7.04 above but top side short rail.

All description as per item No 7.04 above but bottom large stiffener

All description as per item No 7.04 above but bottom short stiffener

TABLE 3'x3' (STEEL) with/without drawer(DRAWING NO. FD-1009/1010) :- Removing old unserviceable/ broken top from table 3'x3' with/without drawer, S&F of new top made of 18/19mm thick pre-laminated particle board exterior grade ISI marked alongwith 4mm thick teak wood beading/Std PVC edging alround the top after completing necessary welding work wherever required duly applying one coat of synthetic enamel OG paint all over iron surface. S&F 4 nos new hard rubber toe at bottotm of legs complete all as per drgs and specified or directed by Engr-in-Charge.

Repair to old unserviceable/broken parts of TEAPOY and S&F/M&L the following new parts/work all as per drgs drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-278/382).

Removing of old unserviceable/ broken top of teapoy, S&F new top made out of 18/19mm th pre-laminated particle board (ext grade) ISI marked with 4mm thick 1st Class teak wood beading alround incl french polished alongwith following work all as per drgs.

Removing old unserviceable/ broken top long rail of teapoy, S&F top long rail made out of 1st class hard teakwood, duly french polished made to shape all as per drgs.

All description as per item No 9.02 above but top short rail.

All description as per item No 9.02 above but legs.

All description as per item No 9.02 above but stiffners.

Repair to old unserviceable/ broken part of TABLE PEG and S&F/M&L following new parts/work all as per drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-236/277/384).

Removing old unserviceable/ broken top of table peg, S&F new top made out of 18/19mm thick MDF/pre-laminated particle board of one side teak face exterior grade, ISI marked screwed so long from top rail including 04 mm thick 1st class teak wood beading duly french polished alongwith following work all as per drgs.

Removing old unserviceable/ broken legs from Peg table, S&F of new legs made out of 1st class teakwood duly french polished till gloosy shining to complete surface all as per drgs.

All description as per ser item No 10.02 above but top side long rails.

All description as per ser item No 10.02 above but top side short rails.

All description as per ser item No 10.02 above but stiffner/bottom rails.

CHAIR VERANDAH (Drawing No.FD-359) : Removing old unserviceable/ broken cane of chair verandah, S&F two coats of White synthetic enamel paint after welding work wherever required duly cleaning of iron surface. Supply & canning to complete chair (seat & back) with 2mm cane nylon/plastic in mat pattern. S&F 04 Nos hard rubber toe/shoe of 3mm size in bottom of legs all as per drgs.

Removing of old unserviceable/broken parts of SOFA (SINGLE SEAT) and S&F/M&L following new parts/work all as per drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-281/373)

Removing old unserviceable/ broken front leg of existing sofa single seater, S&F of new Front legs made of 1st class hard teakwood duly polished incl new Nylon buffers at bottom of legs, size and shape all as per drgs.

All description as per ser item No 12.01 above but rear leg.

All description as per ser item No 12.01 above but Front rail.

All description as per ser item No 12.01 above but back rail.

All description as per ser item No 12.01 above but back top frame.

All description as per ser item No 12.01 above but Arm rest.

All description as per ser item No 12.01 above but Side rail.

All description as per ser item No 12.01 above but Seat/Back batten/bearers.

Takingout old unserviceable covered cushion of sofa, S&F new 100mm thick cushion 520x560mm (cool foam branded), 32mm density covered with best quality tapestry cloth (with zip covered). Colour shall be used after approval of Engr-in-Charge all as per drg.

Removing of old unserviceable/ broken parts of SOFA TWO SEATER (SINGLE SEAT) and S&F/M&L following new parts/work all as per drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-281/373)

Removing old unserviceable/ broken front leg of existing sofa 2 seater (single piece), S&F of new Front legs made of 1st class hard teakwood duly polished including new Nylon buffers at bottom of legs, size and shape all as per drgs.

All description as per ser item No 13.01 above but rear leg.

All description as per ser item No 13.01 above but Front rails.

All description as per ser item No 13.01 above but back rails.

All description as per ser item No 13.01 above but back top frame.

All description as per ser item No 13.01 above but Arm rest.

All description as per ser item No 13.01 above but Side rails.

All description as per ser item No 13.01 above but Seat/Back batten/bearers.

Takingout old unserviceable covered cushion of sofa, S&F new 100mm thick cushion 520x560mm (cool foam branded), 32mm density covered with best quality tapestry cloth (with zip covered). Colour shall be used after approval of Engr-in-Charge all as per drg.

Removing of old unserviceable/ broken parts of SOFA FIVE SEATER and S&F/M&L following new parts/work all as per drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-281/373)

Removing old unserviceable/ broken front leg of existing sofa 2 seater (single piece), S&F of new Front legs made of 1st class hard teakwood duly polished including new Nylon buffers at bottom of legs, size and shape all as per drgs.

All description as per ser item No 14.01 above but rear leg.

All description as per ser item No 14.01 above but Front rails.

All description as per ser item No 14.01 above but back rails.

All description as per ser item No 14.01 above but back top frame.

All description as per ser item No 14.01 above but Arm rest.

All description as per ser item No 14.01 above but Side rails.

All description as per ser item No 14.01 above but Seat/Back batten/bearers.

Takingout old unserviceable covered cushion of sofa, S&F new 100mm thick cushion 520x560mm (cool foam branded), 32mm density covered with best quality tapestry cloth (with zip covered). Colour shall be used after approval of Engr-in-Charge all as per drg.

Repair old unserviceable/ broken parts of TABLE DINNING 6 PERSON and S&F/M&L the following new parts/work all as per drgs drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD - 239/269/273/376)

Removing old unserviceable/ broken top of table dining 6 persons, S&F of new top made out of 18/19mm MDF/pre-laminated particle board, exterior grade including 6mm thick teakwood lipping alround duly polished complerte alongwith fwg work all as per drgs.

Removing old unserviceable/ broken legs of table dining, S&F new legs made out of 1st class teak wood with MS right angle screwed with rail & leg for extra strength duly french polished incl new Hard Nylon buffers screwed at bottom of legs complete all as per drgs.

All description as per ser item No 15.02 above but long rail.

All description as per ser item No 15.02 above but short side rail.

All description as per ser item No 15.02 above but stiffner.

M&L for preparing old wooden surfaces by sand paper of following furniture items and applying one coat of french polish till gloosy finishing all as per drg, specified and directed by Engr-In-Charge:-

Bed Hard (DRAWING NO. FD - 246)

Chair Dinning (DRAWING NO. FD - 228)

Peg Table (DRAWING NO. FD - 384)

Table bed side (DRAWING NO. FD - 228)

Table Writing (DRAWING NO. FD - 249)

Table 3'x2' without drawers (DRAWING NO. FD - 284)

Sofa (Single seat piece) (DRAWING NO. FD - 281/373)

Sofa (2 seater, single piece) (DRAWING NO. FD - 281)

Chair Writing (DRAWING NO. FD - 280)

Chair WB with out arms (DRAWING NO. FD - 285)

Book case (DRAWING NO. FD - 237)

Chair Easy (DRAWING NO. FD - 229)

Table Dinning 06/08 persons (DRAWING NO. FD - 273)

Table 3'x2' with drawers (DRAWING NO. FD - 283)

Table Center (DRAWING NO. FD - 274)

Table dressing gents with mirror (DRAWING NO. FD - 230)

Table dressing ladies with mirror (DRAWING NO. FD - 251/378/MAP)

Teapoy (DRAWING NO. FD - 278)

Sofa (5 Seater) (Drawing No-FD-281)

Sofa (4 Seater, Single Piece) (Drawing No FD-281)

M&L for preparing old steel surfaces scraping with sand paper of rusted portion of following furniture items and applying one coat of synthetic enamel paint (OG/Black) inside and outside all as per drg, specified and directed by Engr-In-Charge:-

Almirah large steel (DRAWING NO. FD - 1031, FD/E6/MAP/18)

Almirah med steel (DRAWING NO. FD - 1032)

Shoe rack steel (DRAWING NO. FD/E6/MAP/02®

Locker bed side steel (DRAWING NO. FD - 1029)

Table office clerk steel (DRAWING NO. FD - 84/1004)

Table officer steel (DRAWING NO. FD - 84/1003)

Removing old unserviceable/ broken parts of CHAIR WRITING and S&F/M&L following new part/work all as per drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-280)

Removing old unserviceable/ broken plastic cane from chair writing, S&F new plastic cane of 2mm size and canning (Godrej pattern) to chair seat alongwith new wooden member screwed to side frames for canning on each side, completed alongwith following necessary repair/polished work. S&F new 4 nos hard rubber ring duly screwed at bottom of leg all as per drgs.

Removing old unserviceable/ broken Rear legs from chair writing and S&F of new rear legs made out of 1st class teakwood duly french polished till gloosy shining to complete surface all as per drgs.

All description as per ser item No 18.02 above but front leg.

All description as per ser item No 18.02 above but front rail.

All description as per ser item No 18.02 above but back rail.

All description as per ser item No 18.02 above but side rail.

All description as per ser item No 18.02 above but stiffener.

All as per ser item No 18.02 above but arm.

Repair to old unserviceable/ broken parts of CHAIR WB WITHOUT ARM and S&F/M&L the following new parts/work all as per drgs drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-58/285)

Removing old unserviceable/ broken seat from chair WB, S&F of new seat made out of 6mm thick commercial plywood ISI marked with 6mm perforation & fixed with screws complete surface alongwith following works all as per drgs.

Removing old unserviceable/ broken rear leg from chair, S&F of new leg made out of 1st class teakwood duly french polished till gloosy shining with hard rubber right at bottom of legs complete surface all as per drgs.

All description as per item No 19.02 above but front leg.

All description as per item No 19.02 above but front rail.

All description as per item No 19.02 above but back rail.

All description as per item No 19.02 above but side rail.

All description as per item No 19.02 above but top support between rear leg.

All description as per item No 19.02 above but stiffener.

Repair to old unserviceable/ broken part of MIRROR WITH SHELF and S&F/M&L following new parts/work all as per drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-52M)

Removing old unserviceable/ broken frame from existing mirror with shelf, S&F new 25x19mm frame of 1st teakwood with 4mm TW beading duly french polished till gloosy shining to complete surface alongwith following works all as per drgs.

Removing old unserviceable/ broken mirror of mirror with shelf, S&F new mirror of 5.5mm thick, ISI marked all as per drgs.

Removing old unserviceable/ broken back surface of plywood of mirror with shelf, S&F new back made out of 6mm th plywod ISI Marked with 2 nos new key plate for handing of mirror all as per drgs.

Removing old unserviceable/ broken shelf of mirror with shelf, S&F new shelf made out of 18/19mm thick MDF/pre-laminated particle board of one side teak face exterior grade, ISI marked including 04mm thick 1st class teak wood beading duly french polished with support of 2 nos MS bracket duly screwed so long all as per drgs.

Removing old unserviceable/ broken parts of TABLE CENTRE and S&F/M&L the following new parts/work all as per drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-235/274)

Removing old unserviceable/ broken top of table Centre, S&F new top made out of 18/19mm th MDF/prelaminated particle board exterior grade of teak veneered outside screwed so long from top rail alongwith 4mm thick edging alround of top complete alongwith following works all as per drgs.

Removing old unserviceable/ broken top long rail of table centre, S&F new long rail made of 1st class hard teak wood duly french polished incl new Hard Nylon rings/buffers at bottom of legs complete all as per drgs.

All description as per ser item No 21.02 above but top short rails.

All description as per ser item No 21.02 above but bottom side rails.

All description as per ser item No 21.02 above but legs.

All description as per ser item No 21.02 above but top centre stiffner.

Repair old unsv/broken parts of TABLE DINNING 4 PERSON (1200x900x750mm) and S&F/M&L the following new parts/work all as per drgs drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-FD/MAP-II/03)

Removing old unserviceable/ broken top of table dining, S&F new table top made out of 18/19mm MDF board/pre-laminated particle board of exgterior grade with 6mm thick teakwood lipping alround duly polished complete alongwith fwg work all as per drgs.

Removing old unserviceable/ broken legs of table dining, S&F new legs made out of 1st class teak wood with MS right angle screwed with rail & leg for extra strength duly french polished including new Hard Nylon buffers screwed at bottom of legs complete all as per drgs.

All description as per ser item No 22.02 above but long rail.

All description as per ser item No 22.02 above but short side rail.

All description as per ser item No 22.02 above but stiffner.

Repair old unserviceable/ broken parts of TABLE DINNING 8 PERSON (1800x900x760mm) and S&F/M&L the following new parts/work all as per drgs drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-239/269/273/376)

Removing old unserviceable/ broken top of table dining 8 persons, S&F of new top made out of 18/19mm MDF/pre-laminated particle board, exterior grade including 6mm thick teakwood lipping alround duly polished complete alongwith following work all as per drgs.

Removing old unserviceable/ broken legs of table dining, S&F new legs made out of 1st class teak wood with MS right angle screwed with rail & leg for extra strength duly french polished including new Hard Nylon buffers screwed at bottom of legs complete all as per drgs.

All description as per ser item No 23.02 above but long rail.

All description as per ser item No 23.02 above but short side rail.

All description as per ser item No 23.02 above but stiffner.

Repair to old unsv/broken parts of TABLE OFFICE CLERK STEEL and S&F the following new parts/work all as per drgs drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-84/1004)

Removing of old unserviceable/ broken top of table, S&F new top made out of 18/19mm th MDF/prelaminated particle board (ext grade) ISI Marked teak veneered face with 4mm thick teakwood beading alround with french polished complete alongwith following work all as per drgs.

M&L for painting of table steel with one coat of synthetic enameled OG paint after necessary welding work wherever required. S&F 04 new legs shoes at bottom of legs complete all as per drgs.

Removing of old unserviceable/ broken drawers of table, S&F new drawers made out of 1mm TH MS sheet incl one coat of synthetic enameled OG paint over a coat of primer complete all as per drgs.

Removing of old unsv/broken locks of table, S&F new locking arrangment complete all as per drgs.

Repair to old unserviceable/ broken parts of TABLE DRESSING GENTS and S&F/M&L the following new parts/work all as per drgs drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-230)

Removing old unserviceable/ broken mirror, S&F new 5mm TH electro copper plated mirror of polished glass with 6mm TH plywood framed with 25x35mm TW batten alround with suitable key plate for hanging complete alongwith following work all as per drg.

Removing old unserviceable/ broken drawer of table dressing gents, S&F new drawers made of 12mm th particle board fixed with 1.5mm plastic laminated sheet of teak face of front side of drawers with 3mm thick teakwood edging duly polished.

Removing old unserviceable/ broken top of table, S&F new top made out of 12mm th particle board fixed with 1.5mm plastic laminated sheet of teak face with 3mm thick teakwood edging complete all as per drgs.

Removing old unserviceable knob, S&F of 25mm CP new knob of best quality complete all as per drgs.

Repair to old unserviceable/ broken parts of BOOK CASE and S&F/M&L the following new parts/work all as per drgs drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-237)

Removing old unserviceable/ broken back plywood, S&F fixing new back made of 6mm TH plywood commercial ISI mark complete alongwith following work all as per drgs.

Removing unserviceable/ broken top of book case, S&F new top made out of 18/19mm TH pre-laminated particle board one side with teak veneer on top face with 3mm thick teakwood edging alround all as per drgs.

All description as per item No 26.02 above but shutters with hings continious piano type rest all as per drg.

All description as per item No 26.02 above but bottom surface.

All description as per item No 26.02 above but sides.

Removing old unserviceable/ broken legs of book case, S&F new legs made out of 1st class teakwood duly french polished rest as per drgs.

All description as per item No 26.06 above but bottom long rail.

All description as per item No 26.06 above but bottom short rail.

Removing old unsv/broken knob of book case and S&F new double full size knob rest all as per drgs

Repair to old unserviceable/ broken parts of SIDE BOARD and S&F/M&L the following new parts/work all as per drgs drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-241/371)

Removing unserviceable/ broken Top of side board, S&F new top made out of 19mm th pre laminated particle board one side with teak veneer on top face with 4mm thick teakwood edging alround complete alongwith fwg works all as per drgs.

Removing unserviceable/ broken Shutter of side board, S&F of new shutter made out of 18/19mm thick pre-laminated particle board (ext grade) ISI marked one side teak face with 2 nos anodised metalic knobs of teak colour all as per drgs.

All description as per item No 27.01 above but shelf.

All description as per item No 27.01 above but bottom.

All description as per item No 27.01 above but side.

All description as per item No 27.01 above but drawer.

Removing unserviceable/ broken back of side board, S&F new back made out of 12mm thick particle board with teak veneered finish one side all as per drgs.

Removing unserviceable/ broken legs of side board, S&F new short legs made out of 1st class hard teakwood, duly french polished all as per drgs.

Repair to old unserviceable/ broken parts of TABLE OFFICE OFFICER STEEL and S&F/M&L the following new parts/work all as per drgs drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-84/1003)

Removing of old unserviceable/ broken top of table officer steel, S&F new top made out of 18/19mm pre-laminated particle board exterior grade, ISI marked including 4mm thick teakwood beading alround duly french polished alongwith following works all as per drg.

Repairing and painting of table office officer steel after necessary repair/welding works wherever required with one coat of synthetic enameled OG paint. S&F 4 Nos new legs shoes all as per drg.

Removing of old unserviceable/ broken drawers of table, S&F new drawers made out of MS sheet 01mm thick including one coat of synthetic enamele OG paint over one coat of primer paint, size and shape shall be as per drgs.

Removing of old unserviceable/ broken drawer's locks of table officer steel, S&F new lock of ISI marked as approved, all as specified and directed by Engr-In-Charge.

Repair to old unserviceable/ broken parts of TABLE DRESSING Ladies and S&F/M&L the following new parts/work all as per drgs drgs and specified or directed by Engr-in-Charge: - (DRAWING NO. FD-251/378/FD/MAP-II/07)

Removing old unserviceable/ broken mirror, S&F new 5mm thick electro copper plated mirror of polished glass with 6mm thick plywood framed with 45x40mm teakwood batten alround complete alongwith following work all as per drg.

Removing old unserviceable/ broken drawer of table dressing ladies, S&F new drawers made of 12mm th particle board fixed with 1.5mm plastic laminated sheet of teak face of front side of drawers with 3mm thick teakwood edging duly polished.

Removing old unserviceable/ broken top of table, S&F new top made out of 12mm th particle board fixed with 1.5mm plastic laminated sheet of teak face with 3mm teak wood edging complete all as per drgs.

Removing old unserviceable knob, S&F of 25mm CP new knob of best quality complete all as per drgs.

Repair to old unserviceable/ broken parts of LOCKER BED SIDE STEEL S&F/M&L the following new parts/work all as per drgs drgs and specified or directed by Engr-in-Charge :- (DRAWING NO. FD-1029)

Preparing steel surfaces of locker steel and applying one coat of synthetic enamel paint OG shade through spray gun to both inner and outer sides after completing necessary welding, denting work including 20 mm CP Steel conuduit pie 1.6mm thick with socket all as directed by Engineer-in-Charge.

Removing unserviceable CP steel handle 100mm long, S&F new Handle all as per drawing.

Removing unserviceable CP Hasp & staple 75x40x3mm, S&F new Haspe & Staple all as per drawing.

Removing old unserviceable Legs of locker steel, S&F/M&L new legs made of 1mm th black steel sheet duly one coat of primer and two coats of OG paint all as per drg.

Removing old unserviceable Shutters of locker steel, S&F/M&L new shutters made of 1mm th black steel sheet duly one coat of primer and two coats of OG paint all as per drg.

REPAIRS/PAINTING TO ALMIRAH MEDIUM STEEL WITH SHELVES (DRAWING NO. FD-67/1032)

Preparation of steel surfaces, including rusted portion of almirah medium steel by scraping with sand paper applying one coat of synthetic enamel OG paint with spray gun on complete almirah inside and out side after completing welding, denting works wherever required. complete all as specified and directed by Engineer-in-Charge.

Removing of old unserviceable/broken handle of almirah medium steel and S&F new CP handle as approved by Engineer-in-Charge and all as directed.

Removing of old unserviceable/broken lock of almirah medium steel and S&F new lock of make: Godrej/Harrison/Link as approved by Engineer-in-Charge and all as directed.

Removing of old unserviceable/broken single shelf of almirah medium steel and S&F new shelf made out of MS sheet 1 mm thick fabricated to shape and size all as shown in drawings.

Removing of old unserviceable/broken legs of almirah medium steel and S&F new legs made out of MS sheets 1 mm thick fabricated to shape and size all as shown in drawings.

Removing of old unserviceable/broken Clips for fixing of almirah large steel and S&F new clips made out of mild steel all as shown in drawings.

REPAIRS/ PAINTING TO ALMIRAH LARGE STEEL WITH SHELVES (DRAWING NO. FD-67/1031)

Preparation of steel surfaces, including rusted portion of almirah large steel by scraping with sand paper, applying one coat of synthetic enamel OG paint with spray gun on complete almirah inside and out side after completing welding, denting works wherever required. complete all as specified and directed by Engineer-in-Charge.

Removing of old unserviceable/broken handle of almirah large steel and S&F new C P handle as approved by Engineer-in-Charge and all as directed.

Removing of old unserviceable/broken lock of almirah large steel and S&F new lock of make: Godrej/Harrison/Link as approved by Engineer-in-Charge and all as directed

Removing of old unserviceable/broken single shelf of almirah large steel and S&F new shelf made out of M S sheet 1 mm thick fabricated to shape and size all as shown in drawings.

Removing of old unserviceable/broken legs of almirah large steel and S&F new legs made out of M S sheets 1 mm thick fabricated to shape and size all as shown in drawings

Removing of old unserviceable/broken clips for fixing of almirah large steel and S&F new clips made out of mild steel all as shown in drawings.

NOTE :- An amount of Rs. 10,400.00 on account of Credit Schedule for Schedule 'A' Part-II shall be deducted from total quoted amount of BOQ to arrive at the contract sum.

M/S M.S TANVEER ENTERPRISES (BID ID -3243296)

M/S B A Traders (BID ID -3249145)