REPAIR TO WALL, PLASTER, PAINTING AND MISC B/R WORKS UNDER AGE B/R-II AT BABINA CANTT

Amount

Demolition of Brickwork or stone/ boulder masonry, laid dry, stacking the serviceable stone for re-use and disposal of debris and rubbish to low level area complete all as directed by the Engr-in-Charge.

M & L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 as in wall complete all as specified and as directed.

M&L walling of random rubble uncoursed well bonded bedded and solidlly hearted built in cement mortar 1:4 complete all as specified and as directed.

M&L walling of random rubble uncoursed well bonded bedded and solidlly hearted built in cement mortar 1:4 except stone complete all as specified and as directed.

M & L PCC 1:2: 4 type B-1 using 20 mm graded store aggregate as in surface channel, drains etc including use and waste of form work where necessary complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc incl racking out joints hacking for key and scrabbing down with water etc complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using forms, moulds, mitred/stopped ends etc complete all as specified and as directed.

Add for each 25 mm girth or part them of over or under 30cm ditto complete all as specified and as directed.

M & L 15 mm thick rendering in cement mortar 1:4 on brick/ stone or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

M & L two coat of white wash on newly plastered surfaces of wall including preparation of surface complete all as specified and as directed.

M & L one coat of white wash on old plastered surfaces of wall including preparation of surface all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving n. exc 15 cm thickness below or above ground level complete all as specified and as directed.

M & L PCC 1:3:6 type C-1 using 20 mm graded store aggregate as in coping/surface channel /drains/wall complete all as specified and as directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided forcomplete all as specified and as directed.

M&L Cement concrete 1:4:8 type D2 (using 40mm graded stone agg) in foundations, filling and mass concrete complete all as specified and directed

M & L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over 15mm thick screed bed in CM 1:4 specified and directed by engr-in-charge.

Dismantling of existing RCC, wood, or steel fencing post embedded in concrete, brick work etc including taking out embedded portion of post in concrete and making good to disturbed ground complete all as specified and as directed .

S&F joist , channel angle or tie sections fixed independently without connecting plates etc ( cut to ordinary length I,e, within 20 mm of the length indicated and drilling holes and bending etc as required ) Fe 310-0 or Fe 410-0 complete all as specified and as directed

S&F Galvanized two strands steel barbed wire 2.24 mm dia barbed with 2.00 mm dia barbs at 75 mm spacing and straining and fixing to any type of strandard rails straining bolts including securing or laying at crossing with and provn of galvanized mild steel wire staples are steel pins as directed.

M&L for framed work such as in doors or gate or angle or other section with gusset plates rails braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hook and hinges (exclusive steel sheeting or other covering running rails and guids ) and hanging also fastening and fixing complete all as specified and as directed Fe-410(Gde E-250) quality B complete all as specified and as directed .

Dismentling iron work in any description complete all as specified and as directed .

M& L for Chain link MS galvanized fencing including line wires, dia of chain link n less than 3.5mm any mesh, size and type to any type of standards rails, straining bolts etc complete all as specified and as directed .

M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer on steel surfaces of any descripition complete all as specified and as directed.

Demolition of cement concrete (unreinfored )in ground floor and paving n,exc 15cm thickness below or above ground level)complete all as specified and as directed

M&L for 40 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate)as in floor complete all as specified and as directed

M&L Glass dividing strips , 3 mm thick and 22 mm width complete all as specified and as directed .

M&L 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection path laid in panel surface finished even and fair complete all as specified and as directed

M&L Cement concrete 1:2:4 type B2 (using 40mm graded stone agg) in foundations, filling and mass concrete complete all as specified and directed

M&L Stone sett flooring with stone setts of size 200 to 250mm long, 150 to 200mm wide and 150mm deep and sides dressed; bedded in cement mortar 1:3, joints 20mm thick; grouted in cement mortar 1:2 with an admixture of metallic floor hardner 5% by weight of cement and struck flush complete all as specified and directed.

M&L Stone sett flooring with stone setts of size 200 to 250mm long, 150 to 200mm wide and 150mm deep and sides dressed; bedded in cement mortar 1:3, joints 20mm thick; grouted in cement mortar 1:2 with an admixture of metallic floor hardner 5% by weight of cement and struck flush except stone sett complete all as specified and directed.

Demolition of Stone sett paving of any description or thickness complete all as specified and directed

Taking down chowkhats or frames with shutter (with out taking off shutter from the frame)n.exc 1.5 sqm each complete all as specified and as directed

Taking down chowkhats or frames with shutter (with out taking off shutter from the frame) exc 1.5sqm and n exc 4sqm each complete all as specified and as directed

Taking down wooden shutters of any description exc 1 Sqm but n. exc 2 sqm each complete all as specified and as directed.

S&F 125 mm x 60 mm size pressed steel frames for door with one or more rebates including necessary fixing lugs, hinge lock strike plate ect including one shop coat of red oxide primer including cutting holes and making good in PCC 1:2:4type B1 using 20 mm graded stone aggregate complete all as specified and as directed. Note :- 10 mm deformed bar shall be provided in bottom. PCC shall be provided in hollow frame in same rates.

Supply and fix mild steel flat iron of size 25x3 mm as in hold fasts and clamps & similar small articles confirming to Fe-410 W (Gde E-250) complete all as specified and as directed by the Engr-in-Charge.

S&F solid PVC door frames of size 50mmx47m made out of 5mm plain colour PVC sheet reinforced with MS Square tube supplying & fixing in opening as per specification and drawing complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having a VC sheet strip of 20mm which stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rails & bottom rail on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the M.S frame weled/ sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site as per specification & drawing complete all as specified and as directed.

Supply and fix for 30 mm thick factory made flush door shutters solid core construction with block board core and ply wood face panels commercial type on both faces complete all as specified.

Supply and fix 100mm size mild steel butt hinges medium weight, cold rolled complete all as specified and as directed by Engr-in-Charge.

S&F 100 mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type C-21 complete all as specified and as directed.

S&F 150 mm Floor door stopper of aiuminium alloy body and tongue, anodised, with hard drawn steel spring , fixed in floor complete all as specified and as directed

Supply and fix 200mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed by the Engr-in-Charge.

S/F 150 mm size Aluminium handles, cast type, anodised and fixed of approved make & ISI marked complete all as specified and as directed.

Supply and fix 250 mm long aluminium alloy anodised sliding door bolts with hasp staple (Bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and as directed by the Engr-in-Charge.

Material and labour for preparation of new or previously untreated wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed by the Engr-in-Charge.

S/F in repair galvanised mild steel wire clothes 0.56 mm nominal dia of wire and average width of aperture1.18 mm complete fixed with tinned tacks or galvanised wire staples all as specified and as directed

Dismantling floor hearth wall tiling including cement mortar bedding but not backing removing serviceable meterial to store complete all as specified and as directed

Material and labour for colour printed glazed ceramic tiles (Premium quality) (300X600mm) X 6mm thick as in wall,dado/skirtings set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick cement plaster in cement mortar (1 : 4) complete all as specified and as directed by the Engr-in-Charge.

M&L for Vitrified ceramic tiles 600x600x9-10mm thick, light coloured as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed layer in CM 1:6 laid over and including 25mm thick PCC 1:2:4 type B0 using 12.5mm stone aggregate sub floor complete all as specified and directed.

M&L for Vitrified ceramic tiles size 600x600x9-10mm thick, in skirting/dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L non skid ceramic coloured tiles 7 to 8 mm thick ( square or rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, including 15 mm thick screed bed or bedding layer in cement mortar 1:6 in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L non skid ceramic coloured tiles 7 to 8 mm thick ( square or rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, including 10 mm thick rendering in cement mortar 1:4 in skirting/dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and as directed.

M/S M S Constructions

m/s gupta trading