Supplying, erecting and Commissioning of submersible motor with pump set and Installing Fabricated steel kiosk shed for the newly sunk bore well in Ward-N, Block 12 T.S. No. 10/2pt of Murungapakkam Revenue Village in the North West corner of Thee

Amount

Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m - all kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m - all kinds of soil - pipes,cables etc , not exceeding 80mm dia

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size)

Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 coarse sand)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc .complete - 40mm thick with 20mm nominal size stone aggregate

12mm cement plaster of mix -1:4 ( 1 cement : 4 fine sand)

Dismantling manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - bituminous road

Supply of Quarry rubbish including stacking to department gauge for premeasurement and spreading required thickness

Providing flanged joints to double flanged C.I./D.I. pipes and specials including necessary bolts, nuts, rubber insertion and testing of joints etc.,complete - 100mm diameter pipe.

Providing and fixing C.I. sluice valve (PN 1.6) (with handwheel) conforming to IS 14846 and ISI marked, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 100 mm dia.

Providing and fixing C.I. Double air valve with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 40 mm dia.

Providing and fixing C.I. Ball type non return valve (PN 1) conforming to IS 318 & IS 1363, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 100 mm dia.

Providing and laying Ductile Iron Double flanged pipes of class K9 (Electro steel/Sripipes/Jindal/Electrotherm) conforming to IS specification 8329/2000 and ISI marked suitable for flanged joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches(or fixing in over head tanks above ground level) laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS12288 and CPWD specification . (earth work and jointing of pipes with rubber insertion will be paid separately) -100mm dia.

Providing and fixing in position flanged standard D.I. specials (Electro steel/Sripipes/Jindal/Kiswok) such as tees, bends, collors, tapers, caps etc.conforming to IS specification 9523/2000 and ISI marked - 100 to 300mm dia.

Providing, laying and jointing G.I pipes of medium class (blue)(TATA,TNT,Nezone,Apollo,Zenith) conforming to IS specification 1239 part I and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including GI specials such as bends,tees, elbow,coupling,reducer etc.,complete all as per IS and CPWD specification. -65mm dia

Providing and fixing in position G.I. pipe nipple 30cm long, including labour charges for jointing, jointing materials etc,complete -40 mm dia.

Providing and fixing mild steel bracket including bolts,nuts,rubber insertion, labour charges etc,complete-100 x 40mm dia

Providing and fixing mild steel flange including bolts,nuts,rubber insertion, labour charges etc,complete-40mm dia

Providing and fixing mild steel flange including bolts,nuts,rubber insertion, labour charges etc,complete-100mm dia

Supplying of electrically operated wet type submersible motor and pumpset (Texmo/KSB/Taro/Kirloskar make), AC 3 phase, 415 volts, 50 Hz, 2900-3000 RPM. The pump shall have brass impeller, high grade steel shaft with sufficient stages having outlet size of 2"/2.5"/3" dia. to suit the borewell (150 / 200mm dia.), complete. The rate includes, all taxes, freight, etc., FOR at site in UT of Puducherry. The pumpset shall be guaranteed for a period of one year from the date of commissioning.(15 HP Submersible motor and pumpset).

Supplying and fixing of 10KVAR power capacitor (CG/L&T/Siemens make) for 17.5/20 HP motor complete.

Supplying and fixing of fully automatic air break star-delta starter range for 23A to 33A F.A.S.D. (Bharat Culter Hammer/L&T/Siemens make) with suitable M.S. angle frame etc.,complete.- 35 HP pumpsets-(ML2)

Supplying and fixing of 1x3x6 sqmm (single run) PVC insulated copper submersible flat flexible cable of Finolex make complete.-12.5HP to 20HP pumpset

Supplying of 3.5/4x50 sqmm underground cable (Paragon/suncab/Empire) complete.-suitable for (30HP to 40HP pumpset)/(upto 40KVA Genset).

Laying of UG cable and providing termination of cable joint with suitable cable gland,cable socket etc., complete - 3.5/4 x 50 / 3.5/4 x 70 sqmm cable.

Supplying and fixing of meter board of size 600mmx900mmx150mm on suitable angle frame with suitable water proof plywood 12mm thick for receiving ED supply. The board frame shall be painted and covered on all sides by 16 gauge M.S. sheet and fixed with 3 Nos. of 100 Amps fuse carrier (Havells/Standard/Anchor make) with screws etc., complete.

Supplying and fixing of teak wood aerial board with 100 Amps HRC fuse base and fuse link and suitable post clamp to hold the G.I. Pipe with electric post including bolts and nuts etc., complete.

Making earth pit of G.I. pipe for earthing in earth pit with 40mm dia. G.I. pipe medium class of length 3.05m perforated with 46 Nos of 12mm dia. holes, pipe lowered in bore holes of 150mm dia. and filled in with charcoal and salt in alternative layer of 300mm, the top of G.I. pipe shall be clamped. Earth pit shall be provided with 60cm dia precast ring with 60cm depth alround,covered with R.C.C. precast slab etc. as per I.E. standards.

Supplying and fixing of copper flat (25 x 3mm) for earthing arrangements including bolts and nuts etc.

Supplying,fixing and lowering into the borewell high tensile threaded PVC column pipes which are to be connected to the submersible pump,including labour charges,jointing materials etc.,complete.-100 mm dia

Supplying and fixing of C.I. adopter which is to be connected to submersible pump delivery pipe.-100 mm dia

Supplying and laying of 16mm dia nylon rope for holding of motors.

Supplying and laying of 40mm dia. PVC pipe (Class 3 - PN 0.6 Mpa) conforming to IS 4985 : 2000 for inserting submersible cable from borewell to starter.

Supply and fixing of 80/100mm dia. M.S. erection clamps of size 80mmx12mm with bolts, nuts, washer etc., complete.

Erection, testing and commissioning of motor and pumpset complete.The rate includes obtaining electricity service connection from Electricity Department also.

Supply and providing of fabricated steel Kiosk of internal dimension 2.20 x 1.90m with front and rear height of 2.40m and 2.10m respectively. The fabrication of the kiosk is to as per the details below:- The corner pillar of the Kiosk shall be of single equal M.S. angle 50x50x6mm tied up at the top, bottom and middle with 40x40x6mm angle, intermediate support of M.S. angles (2 Nos) of 40x40x6mm in all 4 sides and stiffener in vertical with 40x6mm flats and shall not exceed 0.50m C/C. For roof 2 nos. of 40x40x6mm angles to a length of 1.90 mts. each with 3 nos. of 40x6mm flat for a length of 2.20 mts. shall be provided. The front door portion an extra angle of 40x40x6mm of 2.40 mm as vertical and as horizontal lintel of 0.65m of the same angle are to be provided. The door shall be of 0.60mx1.85m with 40x40x6mm angle on all the four sides with 1 no. of intermediate horizontal angle of 40x40x6mm with cross stiffener of 40x6mm flats for the doors shutters. The sides of the Kiosk shall be of 18SWG GI corrugated sheet and roof shall be colour coated galvalume sheet of 550 M.P.A. yield of AZ 150 strength formed as per patterned steel rib profile with the depth of 31 mm pitch of 250mm and overall width of 1060 mm and thickness 0.5mm with required J or C hook bolts & nuts 8mm dia. The rate shall included the cost of all materials, labour, fabrication charges including providing of locking arrangements for the door painting cost with steel primer and paint charges for the angles, painting two coats of enamel paint both inside the Kiosk, transportation to the newly erected borewell site in villages in Puducherry Region etc and erected on platform as directed by the Engineer in charge.