C/O Himachal Niketan at Dwarika Sector-19, New Delhi. (SH- Civil work, WS and SI work and rain water harvesting tank etc.)

Amount

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains in earth work in all heights and depth in all kinds of soils, including saturated soil comprising of pick work, jumper work, and blasting work both in soft and hard rock with chiselling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and as directed by the Engineer -in-Charge at site and sorting out useful and un- useful material and transportation of the un -useful material for disposing at approved dumping site or otherwise and including payment of prescribed charges of dumping to the owner of dumping site (to be arranged by the contractor) for the satisfaction of Engineer- in -Charge through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and other incidentals necessary to complete the work by mechanical means and labour (if required).

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge for all leads including all lifts involved as per direction of Engineer in Charge.

Close timbering in trenches including shuttering, shoring and packing cavities (wherever required) complete (Measurements to be taken of the face area timbered) upto all heights and depths complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Extra for planking, strutting and packing materials for cavities (in close timbering) if required to be left permanently in position (Face area of timber permanently left to be measured) including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30mm x 30mm x 5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 5 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

Foundations, footings, bases of columns, etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access platform with water proof ply 12mm thick.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Circular Column.

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12mm thick.

Edges of slabs and breaks in floors and walls. Under 20 cm wide.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Stairs, (excluding landings) except spiralstaircases.

Providing and laying in position cement concrete 1:5:10 (1 cement : 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) of specified grade excluding the cost of centering and shuttering, All work up to plinth level including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying cement concrete 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to all floor level, excluding the cost of centering, shuttering including finishing complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying in position cement concrete 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) of specified grade excluding the cost of centering and shuttering including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying in position reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) machanically mixed and vibrated of specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying in position Reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) work machanically mixed and vibrated in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to all floor level, excluding cost of centering, shuttering, finishing and reinforcement complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying in position Reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) work machanically mixed and vibrated in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to all floor level, excluding the cost of centering, shuttering, finishing and reinforcement complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix all work up to plinth level, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge complete including carriage of materials in all leads and lifts.

Providing and laying in position M25 of specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement for all work above plinth level upto floor all level complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying in position, hoisting and fixing above plinth level up to floor all level precast reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) in mouldings as in cornices, windows sills etc, including setting in cement mortar 1:3 (1 cement : 3 coarse sand) i/c cost of required centering, shuttering but, excluding the cost of reinforcement complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

String courses, coping bed plates anchor block plain window sills and the like.

Moulding as in cornices window cills etc.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix all work above plinth level to all floor level, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge complete including carriage of materials in all leads and lifts.

Applying cement slurry on R.C.C. slab or cement concrete work using 2.75kgs of cement per square metre of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying cement concrete 1:8:16 (1cement: 8sand: 16 graded stone aggregate 20mm nominal size) and curing complete on slab and floor upto all floor level excluding the cost of form work, screed laid under flooring complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing in RCC work smooth finishing of the exposed surface with cement mortar 1:3 (1 cement : 3 sand) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in Cement mortar 1:6 (1 cement : 6 coarse sand) in superstructure for all floor levels in all shapes and sizes including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 with Cement mortar 1:4 (1 cement :4 coarse sand) in superstructure for all floor levels including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing wood work in second class teak wood in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing wood work in Hollock wood in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing factory made uPVC white colour casement/ casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1mm G.I. section and sash bar/ mullion with 1.50mm ± 0.2mm thick galvanized mild steel section based on wind load calculations, (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, Co- extruded TPV Gasket having saperate drainage system, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100mm x 8mm size for fixing frame to finished wall, After fixing frame the gap between frame and adjacent finished wall shall be filled with PU foam/ weather proof silicon completed in all respect : casement window made from NCL VEKA profilewith openable pannel at both end and center completly fixed and arch at top as per drawing with SS friction hinges (300mm X 19mm X1.9mm) made sash 60mm X 75mm and outer frame 75mm all having wall thickness 2.2mm ± 0.2mm. Window shall be provided with DGU Glass 6mm-12mm-6mm clear toughened of saint gobian makeand all accessories and Hardware as per approved drawings completed in all respect including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws complete in all respect including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including Providing and fixing top & bottom pivot & spring type fixing arrangement, Door handle, lock and stopper and making necessary holes etc. for fixing required door fittings all complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing ACP Sheet in ceiling of size 60cm x 60cm x 3mm thickness mounted on powder coated GI framework fixed/ hanging with wall ceiling at etc. with specific GI screw clamps, GI wires rawl plugs and hold fast etc. complete in all respect including carriage of material in all lead and lift complete as per the direction of Engineer in charge.

Providing and fixing 25mm thick exterior graded block board of kit ply ( gold ) or equivalent that is boiling water proof and termite resistant finish with green spectrum of approved shade and size in ceiling etc. including hard bord living of approved size and duly polished complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 25mm thick exterior graded block board of kit ply ( gold ) or equivalent green spectrum vaneer of approved shade and size in lining with nails etc complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing wooden ground in Hollock Wood 50mm x 25mm section including priming coat complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 19mm thick water proof commercial kit ply or equivalent board in shelve/ box for cupboard with butt joints and fixing with nails and screw etc complete including carriage of material within all lead and lift as per direction of Engineer in charge.

Providing and fixing 19mm thick water proof commercial kit ply (gold) or equivalent board in Shutter for cupboard including fixing with nickel plated piano Hinges with screw etc complete includingcarriage of material within all lead and lift as per direction of Engineer in charge.

Providing and fixing water proof plywood kit ply gold or equivalent in lining with butt jointing including mitring at junctions and nails etc complete ( framework for ways to be measured and paid for separately) including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

9mm thick.

6mm thick.

Providing and fixing plain square edged cover fillets (beading) 40mm X 6mm section including mitring at junction with wooden screw/ nails etc complete in first class teak wood complete including carriage of material within all lead and lifts as per direction of Engineer in charge.

Providing and fixing ornamental moulded (beading) 40mm X 20mm section including mitring at junction with wooden screw/ nails etc complete in first class teak wood complete including carriage of material within all lead and lifts as per direction of Engineer in charge.

Providing and fixing ornamental moulded (beading) 50mm x 20mm section including mitring at junction with wooden screw/ nails etc complete in first class teak wood complete including carriage of material within all lead and lifts as per direction of Engineer in charge.

Providing and fixing ornamental taper moulded (beading) 40mm x12mm section including mitring at junction with wooden screw/ nails etc complete in first class teak wood complete including carriage of material within all lead and lifts as per direction of Engineer in charge.

Providing and fixing square edged cover fillets (beading) 25mm x 6mm section including mitring at junction with wooden screw/nails etc complete in first class teak wood complete including carriage of material within all lead and lifts as per direction of Engineer in charge.

Providing and fixing square edged cover fillets (beading) 19mm x 6mm section including mitring at junction with wooden screw/nails etc complete in first class teak wood complete including carriage of material within all lead and lifts as per direction of Engineer in charge.

Providing and fixing square edged cover fillets (beading) 12mm x 6mm section including mitring at junction with wooden screw/nails etc complete in first class teak wood complete including carriage of material within all lead and lifts as per direction of Engineer in charge.

Providing and fixing ornamental taper moulded (beading) 20mm x 8mm section including mitring at junction with wooden screw/ nails etc complete in first class teak wood complete including carriage of material within all lead and lifts as per direction of Engineer in charge.

Providing and fixing ornamental moulded corner including mitring at junction with wooden screw/ nails etc complete in first class teak wood complete including carriage of material within all lead and lifts as per direction of Engineer in charge:-

20mm x 20mm section.

25mm x 25mm section.

Providing and fixing 4mm thick green spectrum or equivalent vaneered decorative teak plywood lining with decorative surface on one face with but jointing and nails (frame work and cover fillets to be measured and paid for separately) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and Fixing 1.00mm thick decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 100mm x 65mm moulded handrail in straight length including sunk to receive iron core complete in first class Indian teak wood including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 100mm X 100mm decorative newal post in first class teak wood of approved design including fixing with wooden railing and emdedded in cement concrete block 1:2:4 1 cement :2 sand: 4 graded stone aggregate complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 50mm x 50mm ornamental baluster in first class Indian teak wood wrought fixed with ends housed (square or splay) to handrail and treads or string complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing turn cap with ball ornamental in 1st class Indian teak wood at top or bottom of nawels exceeding 100mm x 100mm but not exceeding 150mm x 150mm in section with glued and dowelled joints complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing full length looking mirror of approved quality in face of cupboard 5.50mm thick including fixing of the mirror on the wall/ face of cupboard shutter with teak wood moulded corner/beading of approved design etc complete (moulded corner/ beading to be measured and paid separately) including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing powder coated of required shade (minimum thickness of powder coating 50 micron) aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling to be paid for separately) including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing powder coated of required shade (minimum thickness of powder coating 50 micron) aluminium work for shutters of doors, windows & ventilators including Providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete (only weight of grill to be measured for payment) including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 40mm x 5mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30cm x 10cm x 15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 40mm x 5mm flat iron hold fast 14cm long including khudda fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing arch make (corrosion resistant) or equivalent stainless steel 304 grade sliding door bolt 200mm x 16mm size with nuts and screw etc complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing arch make (corrosion resistant) or equivalent stainless steel 304 grade tower bolt (barrel type) with screw etc complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

200mm x10mm size.

150mm x10mm size.

100mm x10mm size.

Providing and fixing Bright finished kich make ( Corrosion resistant ) or equivelent stainless steel 316 grade handle 100mm size with screw etc complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing bright finished brass 100mm mortice latch and lock with 6 levers and a pair of lever handles of Godrej make or equivelent with necessary screws etc. complete.( Indian make of approved quality) including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 150mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing rubber door silencer with screw etc to suit shutter thickness including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing aluminium tower bolts 150mm X 10mm size, ISI marked, anodised (anodic coating not less than grade AC10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing aluminium handles 100mm, ISI marked, anodised (anodic coating not less than grade AC10 as per IS:1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing glazing with float glass panes of 5 mm thickness (weight not less than 12.50kg/ sqm) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body/ plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. with brass/ Stainless steel cover plate minimum 1.25mm thickness including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing glazing with frosted glass 5.50mm thick in aluminium door window ventilator shutter and partiotion etc. with Neoprene /PVC grasket etc. including carriage of materials in all leads and lift as per direction of Engneer-in- Charge.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body with necessary accessories and screws etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing magnetic catcher of approved quality in cupboard/ ward robe shutters with necessary screws etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing kich make (Corrosion resistant) or equivalent stainless steel 316 grade furniture handle bright finished with screws etc complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 65mm special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 20mm dia stainless steel hanger rod with brackests on both end with screw etc complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing stainless steel coat hoock strip with six hoocks fixed with rawl plugs & screws complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing Godrej make (corrosion resistant) or equivelent 100mm rim latch with a dead bolt and a pair of knob/ handle etc as approved by Engineer-in-Charge with necessary screws etc complete (Indian Make) including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing powder coated telescopic drawer channels 300mm to 600mm long with necessary screws etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing 10mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame or GI Frame (frame work to be paid separately except GI Frame) Flat surfaces including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing 10mm thick plaster of paris (Gypsum unhydrous)ceiling upto a height of 5 metres above floor level over soffits of RCC slabs to to mke it levelled, smooth and even complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Raised moulding/cornices in plaster of paris 50mm in girth including dhar moulding at cornor complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Raised moulding/cornices in plaster of paris 150mm in girth complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying granite stone 20mm thick 80% polished and 20% unpolished in flooring over 20mm(average) thickness base of cement mortar 1:3 (1cement: 3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying granite stone 20mm thick in Skirting/ linning i/c top moulding over 20mm (average) thickness base of cement mortar 1:3 (1cement: 3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing HDF decorative laminate parquat origional flooring AC4 Class, 10mm thick as per the approved sample and shade placed over cusion of 2mm thick expended polyethene foam plus 100 micron thick polyethene sheet under lay no. 045 Beech west including border of required shade and colour complete in all respect upto all floor level including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying 40mm thick Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate with 20 mm nominal size stone aggregate) with a floating coat of neat cement, including cement slurry complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 4mm thick and 40mm wide glass strips in joints of Terrazo/ cement concrete floor including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying vitrified tiles (Matt finish) 800mm x 800mm and 10mm thick of approved shade and brand (SONAMI/ORIENT) with granite border in Skirting/linning etc. in cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified digital tiles of approved brand, size, shade and colour in flooring in cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified digital tiles of approved brand, size, shade and colour in dado of steps, skirting etc. in cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying double charged vitrified tiles 600mm x 600mm and 10mm thick of approved shade and brand (SONAMI/ORIENT) with granite border in flooring treads etc. in cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying double charged vitrified tiles 600mm x 600mm of approved thickness of approved shade and brand (SONAMI/ORIENT) with granite border in Skirting/linning etc. in cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying mirror polished Kota stone slab 25mm thick in flooring/ Skirting over 20mm (average) thick base of cement mortor 1:4 (1 cement :4 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab Including rubbing and polishing complete (slab size not less than 550mm x 550mm ) including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying 15mm (average) thick Slate flooring/ Skirting over 20mm (average) thick base of cement mortor 1:4 (1 cement :4 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying factory made cement concrete interlocking paver block of M -30 grade of NTC make or equivalent made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

80mm thick inter locking paver blocks.

60mm thick inter locking paver blocks.

Providing and laying 40mm thick rubbed Red sand stone flooring/ skirting over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints finished flush including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying granite stone 20mm thick of approved shade and quality in flooring with 5cm wide flaming band with double round nosing complete over 20mm (average) thickness base of cement mortar 1:3 (1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing Ist quality ceramic glazed wall tiles 6mm thick conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dado, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing ceremic tiles 300mm x 600mm x 6mm thick of approved size, brand, shade and design in skirting risers of steps and dado over a bed of 12mm thick cement mortar 1:3 (1cement: 3 sand) finished with flush pointing in white cement complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing Gray Garsa stone/ unistone 15mm (average) thickness cladding on R.C.C./ Brick surfaces side as on faces of Arch masonry walls etc. on 12mm thick cement plaster 1:3 (1cement: 3sand) and jointed with cement slurry i/c scaffolding etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 23cm x 11.50cm x 1.90cm modular brick tile of Bharat Bricks or equivalent cladding on R.C.C./ Brick surfaces side as on faces of Arch masonry walls etc. on 12mm thick cement plaster 1:3 (1cement: 3sand) and jointed with cement slurry i/c scaffolding etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying ceramic highlighter tiles of approved thickness, size, brand, shade and design in skirting risers of steps and dado laid on a bed of 12mm thick cement mortar 1:3 (1cement: 3 sand) finished with flush pointing in white cement complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Making nosing in granite/marble/kota stone etc.20mm to 25mm thick including finished with granite polish mirror finish as per sample approved including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

Half round nosing.

Full Round nosing.

Providing and fixing sandwich PUF roofing of Pre-painted galvanised steel (PPGS) with 50 mm thick Rigid PUF Normal density 35-40 kgs/ m3 complete for Working Temperature of -90 ºC or +90ºC, Adhesion Strength > 100 Kpa, Compressive Strength > 120 Kpa, Thermal Conductivity u= 0.020 W/ M 0 k i/c fixing with G.I. self drilling screws of required sizes / prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 0.60mm thick prepainted steel sheet of TATA Durashine or approved brand and shade and design in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5microns over 5 microns primer coating i/c fixing with G.I. self drilling screws of required sizes / prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing ridges or hips 60cm overall with 0.45 mm thick prepainted steel sheets of TATA Durashine or approved brand, shade and design in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with G.I. self drilling screws of required sizes / prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing valley 90cm overall 0.45 mm thick prepainted steel sheets of TATA Durashine or approved brand,shade and design in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with G.I. self drilling screws of required sizes / prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing flashing 38cm overall with 0.45mm thick prepainted steel sheets of TATA Durashine or approved brand shade and design in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20microns over 5microns primer coating + back coat of polyster of 5microns over 5microns primer coating i/c fixing with G.I. self drilling screws of required sizes / prepainted iron J or L hooks, bolts and nuts 6mm dia meter & prepainted G.I. limpet & bitumen washers complete with all accessories as required complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 30cm wide 120cm overall Box type 0.45mm thick prepainted steel sheets of TATA Durashine or approved brand shade gutter fixed with bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design (frame work to be measured and paid for separately) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing M.S. B.P Sheet 2.00mm (two milimetre) thick in eaves board/ facia/ soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid for separtely) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified: 2 mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specified complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 10mm thick double walled polycarbonate PVC sheet thermolayer solar control/IR transparent sheet of lexus make of equivalent roofing with approved joint of aluminium base plate and cap including rubber washer in between including longitudinal jointing fixed with self drilling screws and washers of required sizes or by any othetr suitable means complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying water proofing treatment with Dr. Fixit-FASTFLEX or equivalent with two components polymer modified cementitious coating consisting of cementitious powder and a polymer liquid in two coats for first coat:- clean and saturate surface and then applying a coat of Dr. Fixit -FASTFLEX by maintaning a coverage of 6-7sft per kg to achive one mm thickness and the same process shalltended upto 300 mm vertically. The second coat shall be applied in opposit direction after four six-hours of application of first coat then sprinkle sand on top surface of applied Dr. Fixit-FASTFLEX while still tacky over the second coat. Then apply cement mortar 1 ; 4 (1 cement :4 sand) admioxed with 200ml of pidiproof LW @ 200ml per 50kg bag of cement over the floor with the suitable grediant towards drain pipe, while the second coat of Dr. Fixit is still tacky complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing on wall face Single socketed 150mm dia PVC Finolex rain water pipes (working pressure 4kg / sqcm) conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing on wall face PVC Finolex moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

Plain Bend 150mm.

Door Bend 150mm.

Coupler 150mm.

PVC Shoe 150mm

PVC Clamp 150mm

Structural steel work riveted, bolted or welded in built up sections including hollow sections in trusses and framed work including beams, chain etc, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Steel work welded in built up sections and hollow sections in framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works complete.

In stringers, treads, landings etc. of stair cases,ornamental brakets and other ornamental works etc. including use of chequered plate wherever required, all complete.

Providing and fixing expanded metal 20mm x 60mm strands 3.25mm wide and 1.6mm thick or as per Arch. Drgs for windows etc. and priming coat with approved steel primer all complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing in position collapsible steel shutters with vertical channels 20mm x 10mm x 2mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40mm x 40mm x 6mm, with 40mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of Providing and fixing necessary 27.50cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters 80mm x 0.90mm M.S. laths with 0.90mm thick top cover complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing ball bearing for rolling shutters complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing M.S.round holding down or anchor bolts with nuts and washer plates complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing M.S. hollow pipe in vertical posts of various dia/ sections welded in straight lengh over M.S. flat at top of vertical balusters including one coat of red oxide priming coat complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing of acoustical fabric gripper intact on 12mm ply pieces with 12mm foam pasted on wood wool tile on back for wall panneling with 50mm U-GI channel fixed with naccesory hardware intact with 50mm rockwool complete in all respect including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing of acoustical pannel on wall with 50mm U-GI channel fixed with naccesory hardware intact with 50mm rockwool complete in all respect including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 360digree movable six wheel roller assembly for bed etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing godrej magna proximity card lock with one piece encoder, one hand held device and guest cards (quantity reqired as per direction of Engineer in Charge) etc. complete including carriage of materials in all leads and lift as per direction of Engneer-in- Charge.

Providing and fixing Mineral Fiber 15mm tile on powder coated 25mm GI frame work fixed /Hanging with wall and ceilling with specified clamp and GI wire hold fasts and rawl plugs etc. including carriage of materials in all leads and lift as per direction of Engneer-in- Charge.

Providing and laying non-pressure 450mm dia R.C.C. pipe NP2 class (Heavy duty) with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 6mm thick HPL Sheet ISI marked in linning with butt joints & fixing with rivets powder coated matching to shade of HPL Sheet complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing bath partition with 10mm clear toughen saint govind glass with sliding door and hardware including instalation complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing in position toughen glass partition with 12mm clear toughen saint govind glass with L-Connector and other necessory hardware complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing in position toughen glass partition with 12mm toughen saint govind frosted glass with L-Connector and other necessory hardware complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 0.35mm thick prepainted TATA steel sheet liner in partition with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20microns over 5microns primer coating to back coat of polyster of 5microns over 5microns primer coating i/c fixing with self drilling screw 55mm size with prepainted limpet and rubber washers complete with all accesoriees as required complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors with Two or more coat applied @ 0.90 liters/ 10 square metre over an under coat of primer applied @ 0.80 liters// 10 square metreof approved brand and manufacture using Primer as per manufacturers specifications. Painting Steel work with Deluxe Multi Surface Paint to give an even shade complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50grams/ litre complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications, Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 90 liters/ 10 square metre over an under coat of primer applied @ 0.75 liters/ 10 square metre of approved brand and manufacture complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Polishing Two or more coats on new works including a coat of wood filler with French spirit complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

6 mm thick cement plaster of mix 1:3 (1 cement : 3 fine sand) in ceiling upto all floor level including carriage of materials in all leads and lift as per direction of Engineer in Charge.

15 mm cement plaster on the rough side of single or half brick wall of mix 1:6 ( 1 cement : 6 Sand) upto all floor level including carriage of materials in all leads and lift as per direction of Engineer in Charge.

15mm cement plaster in single coat on fair side of brick/ concrete/ stone walls for interior plastering upto floor all level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. in Cement Mortar 1:6(1 cement:6 sand) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Plastering single coat on mouldings, cornices or archtraves including neat finish to line and level with cement mortar 1:3 (1 cement : 3 sand) including carriage of material within all leads and lifts.

Applying Floating coat of neat cement complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Finishing walls with textured exterior paint of required shade ates New work (Two or more coats applied @ for external plaster are for height upto 3.28ltr/10sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10sqm complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Distempering with oil bound washable distemper on wall/ ceiling of approved brand and manufacture to give an even shade, New work (two or more coats) over and including water thinnable priming coat with cement primer complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Finishing walls with Acrylic Smooth exterior paint of required shade, New work (Two or more coat applied @ 1.67 ltr/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Wall / ceiling painting with acrylic emulsion paint of approved brand and manufacture to give an even shade, Two or more coats on new work complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall / ceiling surface to prepare the surface even and smooth complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Applying one or more coat of paint based putty made of whiting and POP etc. mixed in required quantity of white enamel paint for application on wood based products after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Stone soling properly hand-packed filling interstices with Kharanja stone compected with durmut, for specified thickness complete as per HP.PWD specification including carriage of materials in all leads and lifts.

Supplying and filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Making chases up to 7.50cm x 7.50cm in walls including making good and finishing with matching surface after housing G.I. pipe etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of ying integral cement based treatment for 4.40kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface, IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface, IIIrd course of applying blown or residual bitumen applied hot at 1.70kg per sqm of area. IVth course of 400micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100mm wide and pasted to each other with bitumen @ 1.70kg/sqm) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying G.I. pipes complete with G.I. fittings complete including trenching and refilling etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

15mm dia nominal bore.

20mm dia nominal bore.

40mm dia nominal bore.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

15mm dia nominal bore.

20mm dia nominal bore.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamp at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

1620 (20mm OD ) pipe.

1216 (16mm OD) pipe.

Making connection of G.I. distribution branch with G.I. main of 25mm to 40mm nominal bore by Providing and fixing tee, including cutting and threading the pipe etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes including fittings like tank nipples, ball cock etc excluding base support for tank complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and laying in trenches 150mm dia PVC FINOLEX type-"B" pipe including coller and filling the joints with approved adhesive complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing on wall face PVC Finolex type-B spigot,socket, waste and ventilating pipes of working pressure not less than 4.5 kg/sqm including coller and filling the joints with approved adhesive complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

110mm dia.

150mm dia.

Providing and fixing PVC Finolex clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

110mm dia.

150mm dia.

Providing and fixing PVC Finolex plain bend ISI marked complete including filling the joints with approved adhesive complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

PVC Plain bend 110mm dia.

PVC Plain bend 150mm dia.

Providing and fixing PVC door bend with oval access door, insertion rubber washer ISI marked complete including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

110mm dia.

150mm dia.

Providing and fixing PVC Finolex single equal branch with oval access door, ISI marked insertion rubber washer complete including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

110mm dia.

150mm dia.

Providing and fixing plain PVC Finolex single equal branch complete including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

110mm dia.

150mm dia.

Providing and fixing Double equal branch ISI marked with ovel access door and washer including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

110mm dia.

150mm dia.

Providing and fixing PVC Finolex collars ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

150mm dia.

110mm dia.

Providing and fixing PVC Finolex off sets 45 degree ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

110mm dia.

150mm dia.

Providing and fixing PVC Finolex cowl ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

110mm dia.

150mm dia.

Providing and fixing PVC floor trap 110mm X 90mm ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing PVC Finolex ‘P’ or 'S' trap 110mm (hundred ten milimetres) nominal size for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing viterous China wash down water closet (European Type W.C. pan) Hindware Make cat No. 92090 or equivalent along with cistern and seat cover with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement : 1 sand) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing vitreous China wash down, water closet complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

Orissa Pattern Hindware Make Cat No.20076 or equivalent.

European seat complete.

Wall hung seat with concealed cistern.

Providing and fixing 10.00liters capacity PVC low level flush cistern Hindware Make sleek plus dual flush or equivalent with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float with push button couplings for connections with inlet outlet and overflow pipe 40mm (forty milimetre) dia C.P flush bend including cutting holes in walls and making good thesame and connecting the flush bend with cistern and closet complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing oval shape veterous china wash basin Hindware Make Zen catagory cat No. 10049 or equivalent make with single hole for pillar tap with C.I. or M.S. brackets (if required) painted white including cutting holes and making good the same but excluding fitting complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 550mm X 400mm size Flat back veterous china wash basin Hindware Make cat No. 10008+11003 with padestal or equivalent with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fitting including carriage of materials in all leads and lifts.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430mm x 260mm x 350mm and 340mm x 410mm x 265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required One urinal basin with 5 litre white P.V.C. automatic flushing cistern complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) Kitchen sink with drain board of size 510mm x 1040mm bowl depth 250mm as per IS:13983 with C.I. brackets and stainless steel plug 40mm, including painting of fittings and brackets, cutting and making good the walls wherever required complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) Kitchen sink without drain board of size 610mm x 510mm bowl depth 200mm as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing C.P brass waste 32mm (thirty two milimetre) dia for wash basin or sink complete complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing C.P. Bottle Trap 32mm (thirty two milimetre) dia for wash basin and sink complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 100mm (One hundred milimetre) C.P. Grating with frame for gully / floor or nahani trap complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing C.P. Extention piece heavy duty complete including carriage of materials in all leads and lift as per direction of Engineer in Charge of 15mm X 50mm size.

Providing and fixing looking mirror fancy type of size 600mm x 450mm with ornamental frame (superior quality) of approved brand design over 6 mm thick water proof Kit ply (Gold) or equivalent including backing support and fixing with screws etc. at site complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing C.P. Non return Valve 15mm nominal bore complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing brass full way valve with wheel complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

15mm nominal bore.

20mm nominal bore

40mm nominal bore

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete, Flexible pipe 32 mm dia complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing G.I./M.I Union of following sizes complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

15mm nominal bore.

20mm nominal bore

40mm nominal bore

Providing and fixing 610mm size C.P. brass towel rail of ESS ESS make catlogue No. AC-101 or equivalent complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing towel ring of ESS ESS make catlogue No. AC-102 or equivalent complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing Acrylic shelf of ESS ESS make catlogue No. AC-107 or equivalent complete fixed to wooden plugs with C.P. brass screws fitting complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing C.P. toilet paper holder of ESS ESS make catlogue No. AC-106 or its equivalent complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing 15mm (fifteen millimetre) nominal bore C.P. brass centre hole basin mixture of ESS ESS make catlogue No. C-211-A or equivalent with capstain head complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing C.P. sink mixer of ESS ESS catlogue No. C-219 or its equivalent with casted botton swinging spaut at top including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing C.P. wall mixture of Ess Ess catlogue No. C-215 or equivalent including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing CP brass bib tap 15mm ( fifteen millimetre) nominal bore with CP flange, capstan head of ESS ESS make or equivalent including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

Long Body ESS ESS catlogue No. C-209 or equivalent.

Short Body ESS ESS catlogue No. C-202 or equivalent.

Providing and fixing C.P. angle cock 15mm ( fifteen millimetre) nominal bore with CP flange of ESS ESS make catlogue No. C-204 or its equivalent of approved quality and colour with flange including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing Health faucet fitting of ESS ESS make catlogue No. C-232D or equivalent complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing PVC hot water connection pipe with brass union viking make or its equivalent including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

45cms length and 15mm nominal bore.

60cms length and 15 mm nominal bore.

Providing and fixing CP soap trays of ESS ESS make catlogue No. AC-103 or equivalent including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing CP robe hooks/pegs of ESS ESS make catlogue No. AC-105 or its equivalent including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing high flow divertor for over head shower with its accessories etc. complete15mm dia of ESS ESS make catlogue No. DS-11 or its equivalent including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing over head shower swing of ESS ESS make catlogue No. HS-102 or its equivalent including arm etc. for 15mm to 20mm inlet with fitting complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

Inside size 90cm x 80cm and 45cm deep including precast RCC cover of NTC make or equivalent 455mm x 610mm internal dimensions, With Sewer bricks conforming to IS : 4885.

Inside size 120cm x 90cm and 90cm deep including precast RCC cover of NTC make or equivalent 500mm internal diameter With Sewer bricks conforming to IS : 4885.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating, Sewer bricks conforming to IS : 4885 chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design including carriage of materials in all leads and lift as per direction of Engineer in Charge.

100mm x 100mm size P or R type.

150mm x 100mm size P or R type.

180mm x 150mm size P type.

Constructing brick masonry road gully chamber 50cm x 45cm x 60cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500mm x 450mm pre-cast R.C.C. horizontal grating with frame complete as per standard design. with common burnt clay F.P.S. (non modular) bricks of class designation 7.50 including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and installing mono block pump 2-HP single phase of kriloskar make or equivalent including fixing complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Making hole up to 20cm x 20cm and embedding pipes up to 150mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand 6 graded stone aggregate 20mm nominal size) including disposal of malba including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Cutting holes up to 15cm x 15cm in R.C.C. beam/floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), including finishing complete so as to make it leak proof including carriage of materials in all leads and lift as per direction of Engineer in Charge.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality including carriage of materials in all leads and lift as per direction of Engineer in Charge:-

H D - 20. Circular shape 560mm internal diameter.

L D- 2.5. Rectangular shape 600mm x 450mm internal dimensions.

Circular shape 450mm internal diameter.

M D - 10. Square shape 450mm internal dimension.

Confoss Construction

KBG ENGINEERS

Unity Builders

S G Constructions

VISHWA BHUMI ENGINEERS P LTD

SUNEHARI BAGH BUILDERS PVT. LTD.

SBC RAPID JV

DELHI ENGINEERS CONSTRUCTION COMPANY

P K Construction Shimla Pvt Ltd