SPECIAL REPAIRS TO BUILDING NO P-34, T-225, P-14, A SEC STREET LIGHTS MIL STATION POKARAN UNDER AGE (I) POKARAN

Amount

Dismantling of Stone slabs and tiles of any description or thickness in floors, walss, aprons etc., removing serviceable tiles to store and rubbish off the premises.

Dismantling of floors health or walls tiling and Stone floor including cement mortar bedded (but not backing) & removing serviceable tiles to store and rubbies of the premises

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out soft/loose soil complete.

Returning, filling in excavated approved soil,(soft/loose soil) including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete.

Removing excavated soil not exceeding100 m and depositing where directed at a level not exceeding 1.5m above the starting point complete.

M&L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in foundations, filling and mass concrete including sub base of floors complete.

Demolition of stone/ boulder masonry and built in cement mortar all as specified & directed by Engineer-in-charge.

M&L for squared rubble masonary, jodhpur type, brought upto courses, well bonded and solidly hearted, built in cement mortar 1:6 all as specified and directed.

Extra over stone masonary for hammer dressing face stones and dressing of the face beds and joints all as specified of squared rubble walling brought upto courses, jodhpur type, with maximum depression of face from straight edge held against the dressed surface n.exc. 20 mm complete

M&L for Jodhpur stone roof slabs, self faced 7.5 cm to 10 cm thick, 25 cm to 35 cm wide, hoisted, set and grouted in lime mortar 1:3 or cement mortar 1:6 complete all as specified and directed

M/L 40 mm thick Cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate for levelling course for consolidated thickness shall be varied from 25 to 85 mm as per the requirement all as directed and specified complete.

M&L for flush pointing single joints in brick work or masonary in detached work, flashing etc, on ceiling in CM 1:4 complete all as specified & directed.

Supply only integral Waterproofing compound.

M&L for APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyester non wove fabric (wt not less than 150 gms/sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 Ltr/Sqm by forced and sealing all the over laps of 75 mm in length side and 100 mm on the width side of membrane all as speficied and directed including following. (i) Complete removal of existing water proofing treatment incl bedding if any n exc. 50mm thick etc. on any type of roof, cleaning with wire brushers etc. and removal of debris out side MD land complete all as specified and directed. (ii) M&L for 10mm thick screed plaster on roof for laying in CM 1:4 waterproofing treatment, with using WPC (WPC will be measured and paid separately as supply only) (iii) Priming the suraface of concrete/plaster with bituminous primer 0.3 liter per Sqm. (iv) Applying 2 coat of Al paint @ 100 ml/sqm

M&L for roughly squared stone lintels n.exc. 3 m in length hammer dressed on face and soffits, hoisted set and pointed in lime mortar 1:3 or Cement mortar 1:3 complete.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering all as specified and directed.

M&L for 75 mm thick cement concrete type D-2 1:4:8 using 40 mm graded stone aggregates as in subbase all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick (square/ rectangular) light shade polished, area of each tiles not exceeding 0.36 Sqm, in floor etc set jointed and pointed in white or coloured cement to match the colour of tiles with screed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6. all as specified.

M&L for vitrified ceramic tiles 10mm thick (square/ rectangular) light shade polished, area of each tiles not exceeding 0.36 Sqm, in vertical surfaces such as skirting etc, set jointed and pointed in white or coloured cement to match with and including backing coat of 10 mm thick in CM 1:4. all as specified & directed.

M&L for coloured Glazed ceramic tiles in vertical surfaces 450 x300x7 mm thick on vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm backing coat in CM1:4 including complete all as specified and directed.

M&L for Kota stone flooring 20-25mm thick incl for cuttting and polishing by machine over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including provision of 20 mm thick screed bedding in CM (1:6)

M&L for Machine cut kota stone slab flooring 20-25mm thick in riser of steps, skirting,dado,and pillar over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including provision of 10 mm thick backing coat of CM (1:3)

S&F for Non- skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with screed bed 15 mm thick CM 1:6 complete all as specified & directed

Taking down door chowket or frame incl shutter area n exc 1.50 sqm each and removing to store.

Taking down door chowket or frame incl shutter area exc 1.50 sqm n exc 4.00sqm each and removing to store.

S&F, Powder coated, anodised aluminium frame & shutter for door, window and ventilator including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, etc complete all as specified & directed by Engineer-in-charge.

M&L for powder coated anodised aluminium door shutter, aluminium section wt 0.55 Kg/m incl necessary joining cleats, glazing clips, rubber neoprene packing, handle 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete.

M&L for powder coated anodised aluminium window and ventilatot shutter, side hung type without sash bars aluminium section wt 0.55 Kg/m incl necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws , anodised alu fittings such as peg stays 150 mm long 01 no, hinges type B-21 100 mm long 02 no, suitable handle 01 no, etc complete.

M&L for sheet glass 5.5mm thick, ordinary quality and glazing with, rubber packing n exc 0.5 sq m in each pane complete all as specified and as directed by the Engineer-in-Charge

M&L for sheet glass 5.5mm thick, ordinary quality and glazing with, rubber packing exc 0.5 sq m in each pane complete all as specified and as directed by the Engineer-in-Charge

S&L extruded aluminium alloy butt hinges, type B-21 100 mm size complete.

S&F Aluminium anodised, barrel tower bolt of extruded section and fix of length 125mm

S&F Aluminium handles, cast type, anodised of size 150mm long.

S&F 2 levers brass mortie lock vertical type, size 100 mm incl escutcheon plates and two keys complete all as specified and directed.

M&L for double action door spring hydraulically regulated made up of minimum 1.25 mm thick aluminium sheet foundation box ,main body with stainless steel cover, grovering piovt made of brass, other parts made of mild steel heavy duty and fixed.

S&F stainless steel wire cloths 0.36mm nominal dia of wire and averaging width of aperature 1.40mm and fixed with stainless steel wire staples complete all as specified & directed.

S&F anodised aluminium grill (anodised transparent or dyed to reqd ahade according IS 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with CP brass/stainless steel screws @ 200mm C/C, incl cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised alu standard section around the opening allcomplete as per reqd and directions of Engr in Charge.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc ) or insulation boards/slabs/blankets any thickness including cover fillets

S&F Anodised aluminium snap grid frame work of size 605 x 605 mm for false ceiling all as specified

M&L for providing and fixing Gypsum board 12mm thick in ceiling fixed with screw as per manufacturers instructions.

S&F ,10mm thick PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium / G.I./M.S. as per specification and drawing, including Anodised aluminium snap grid frame work for false ceiling all as specified

M&L rendering 15mm thick in 1:6 cement plaster on stone masonary surface is to be finished even and smooth (without using extra cement) complete all as specified and directed.

M&L rendering 15mm thick in 1:4 cement plaster on of stone masonary surface is to be finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for rendering 5 mm thick plaster on concrete surfaces as in ceiling in CM (1:4) finished even & Smooth without using extra cement.

M&L preparation of new wall surface and applying two coats of distemper oil emulsion over a coat of alkali resistant primer,including 3mm thick wall care putty on wall complete all as specified and directeded.

M&L preparation of new wall surface and applying three coat of white wash on surfaces of ceiling complete all as specified & directed by Engineer-in-charge.

M&L for Finishing wall with Acrylic emulsion smooth exterior paint of reqd shade, new work (two or more coat) applied @ 1.67 Ltr/10 Sqm over and incl priming coat of exterior primer applied @ 2.20 Kg/10 Sqm complete.

M&L for Granite ( of any type) tiles 20 mm thick machine cut, bedded & jointed with grey cement slurry & pointed with white cement with admixture of pigment to match the shade of granite stone incl cutting and polishing over 15 mm thick screed bed in CM 1:6 complete.

S&F decorative type curtain rod, stainless steel, 25 mm dia with not less than 1 mm wall thickness complete all as specified and directed.

S&F Decorative type curtain bracket, stainless steel suitable for above curtain rod complete all as specified and directed.

M&L Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates,Fe 410-W (Gde E-250) quality A

Preparation of new Steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and direction.

M&L for 5cm sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4, complete complete all as specified and as directed by the Engineer-in-Charge

Demolition of PCC in Ground Floor and paving n exc 15 cm (below or above ground level)

M&L for 50 mm thick PCC 1:3:6 type C1 (using 20 mm graded crushed stone aggregates) as in plinth protection finished even and fair & filling the joints with mastic filling i.e. one part of bitumen 85/25 & 3 parts of sand by wt all as specified.

S&F tubes medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid in floors 15 mm dia including taking down steel tubing and connections including cleaning for re-fixing or removal to store of 15 mm bore incl

S&F tubes medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid in floors 20 mm dia including taking down steel tubing necessary fittings connection etc for 20 mm bore pipe incl

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

S&F in repairs Viterious china White Wash Hand Basin of fixed in repairs includign 15 mm pillar cock cast copper alloy CP, 15mm cast copper stop valve, 32 mm brase CP waste fitting, PVC waste pipe 32 mm dia & 15 mm PTMT connection pipe 450 mm long

S& F Soap dish, any type, fixed to plugs with chromium plated brass screws

S&F stop valves, fancy type, CP with long shank and cup (concealed type) screwed both ends for 15 mm bore of iron pipe or for union and fixed all as specified.

S&F 20 mm gun metal, globe or gate valves, with iron wheel head, srewed both ends for iron pipe and fixec complete.

S&F Towel rail CP 20 mm dia D-type 60 cm long between flanges and fixed in position complete.

S&F 450 mm long MS powder coated peg set of 6 hooks complete.

Supply and fix rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in SSR part-I ,500 ltr capacity including, 20mm dia Ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed including dismantling of water tanks and removing to store capacity of tank exc 250 and n exc 500 ltr.

S&F PVC flushing cistern 10 ltrs capacity ISI marked incl PVC down take pipe and connection etc all complete in repairs.

S&F bib taps cast cipper alloy with crutch or butterfly handle, chromium plated fancy type screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs

Supply and fix 15mm bore piller taps of cast copper with capstan head CP screwed down high pressure with or without lettered hot and cold with long screwed shank and fly nut for iron pipe and fixed in repairs

S&F PVC connections 15 mm size with PTMT nuts to length 450 mm in repairs.

Supply and fix in repairs brass Chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union

S/F S S grating dome of 100 mm dia (min wt - 25 gms) to floor traps in repairs.

Supply and fix PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm dia out let

S/F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110 mm dia

S/F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 75 mm dia

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering

S & F Pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified. Fixed as in Ridge.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con-forming to Fe 290.Gde-E-165

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other covering. Door, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings(exclusive of steel sheeting or other covering, running rails & guides) and hanging also fastening & complete all as specified & directed by Engineer-in-charge.

M&L for 60 mm thick machine pressed precast concrete interlocking paver block with grey cement and pigments any shape and size conforming to IS 15658-2006 of M-35 grade inclduing even spreading of 25mm thick layer of sand cushioning incl watering & consolidation all as specified.all as specified and as directed

Taking down carefully point wiring of any type (i.e. on wooden batten, surface conduit, casing-N- capping or concealed conduit) complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, conduit etc. including accessories such as wooden gutties/rawal plug, screw etc including making good disturbed surface to match the existing surface all as specified & directed.

Taking down carefully MCB DB SPN/TPN of any type etc including making good disturbed surface to match the existing surface all as specified & directed.

M&L for point wiring with PVC unsheathed cable single core stranded copper conductor 1.5 sq mm size, 1100 V grade, drawn into casing & caping (ISI marked) not less than 20mm dia on surface with and including PVC unsheathed cable single core copper conductor 1.5 Sq mm as continuous earth wire and including pressed MS sheet sunk in box 1.12 mm thick with 2.8 mm thick laminated bakelite sheet all as specified & directed by Engr-in-charge for the following :- (a) One light/fan/Exh/Bell point controlled by one switch 5 Amp one way

(b) -Ditto- all as per item no 84.but socket outlet 3pin 5 amps same board

(c) -Ditto- all as per item no.84 but socket outlet 3pin 5 amps independent board

-Ditto- all as per item No. 84 here-in-before but for one socket outlet/metal clad socket of 15 Amps fixed on independent board with 4.0 Sq mm multistranded copper conductor wire FRLS PVC insulated and 4.0 Sq mm copper conductor wire FRLS PVC insulated using as earth wire complete all as specified and directed by Engineer-in-Charge

S & F switch piano, flush type ,single pole , one way 5 amps 230V ac confirming to IS: 3854 and ISI marked complete all as specified and directed by Engr in Charge .

S & F socket outlet 5 Amp , 5 pin flush type multi purpose 230V ac complete all as specified and directed by Engr in Charge.

S & F switch piano, flush type single pole , one way 15 amps 230V ac confirming to IS: 3854 and ISI marked complete all as specified and directed by Engr in Charge.

S & F socket outlet 2 in 1, 3 pin 5 / 15 Amp , 230V ac cconfirming to IS: 3854 and ISI marked complete all as specified and directed by Engr in Charge.

supply and fixing fan regulator electronic type five step controlled 230 volt 50 Hz for confirming to IS: 3854 and ISI marked complete all as specified and directed by Engr in Charge .

S&F Sheet metal enclosure DB SPN 240 Volt 8 way double door type with 200 Amps rated bus bar for fixing MCB

S&F MCB SP 240 volts, 6 to 32 Amps, 10 KA, B Curve

S&F MCB SPN 240 volts, 32 Amps, 10 KA C Curve

S&F Lamp holder PVC polycarbonate type with back plate suitable for battern fittings

S&F LED Bulb of 9 watt make - Philips/Bajaj/Havells

S&F Ceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as specified.

S & F LED tube fixture/fitting 1x 20watt, decorative ultra slim square profile with extruded polycarbonate, environmental friendly, energy eficient ready to use prewired for including connecting up with twin core twisted flexible copper conductor cable with suitable size complete and all as specified and directed by Engineer- in Charge.”.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store

M&L for submain wiring with PVC unsheathed cable single core stranded copper conductor 6sq mm size, 1100 V grade, drawn through PVC casing and caping (ISI marked) not less than 25mm dia on surface with and including PVC unsheathed cable single core copper conductor 6.0 Sq mm as continuous earth wire and all as specified & directed by Engr-in-charge.

Supply and lay XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured electric power cable (heavy duty) 1100 Volt grade with stranded aluminium conductor of size 10 sq mm 2 core.

Dismantling old steet light any type and size & Supply, fixing and testing of energy efficient LED street light fitting of 45 watt , pole mounting comprising a pressure die cast housing with toughened glass and individual high power LEDS With secondary optics, IP 66 protection and Impact resistance including 1.5 sqmm twin core wire for electric connection with Overhead conductor to street light complete all as directed by Engineer in Charge

Supply and fixing street light bracket suitable for 45 watt street light , PCC pole mounting comprising a pressure die cast housing with toughened glass and individual high power LEDS With secondary optics, IP 66 protection and Impact resistance complete all as directed by Engineer in Charge

Supply and install street light junction box size 40X3030X20 cubical panel board 1100 volt grade out door type front door and locking arrangement, suitable size alluminium bus bar with MCB SPN 40 Amp including connections complete all as specified and direted.

Hanging only Ceiling fans and connecting of incl provn of cable from ceilling rose or connected to fan

Fixing only Exhaust fan ,and connecting of incl provn of cable from ceilling rose or connected to fan complete all as specified & directed by Engineer-in-charge.

Fixing only Electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 Ltrs, BEE 5 star rated complete with all accessories such as saftey valve, thermostat, NRV, connection piece etc all as specified & directed by Engineer.

M&L for point wiring with PVC unsheathed cable single core stranded copper conductor 1.5 sq mm size, 1100 V grade, drawn into concealed conduit medium grade (ISI marked) not less than 20mm dia on surface with and including PVC unsheathed cable single core copper conductor 1.5 Sq mm as continuous earth wire and including pressed MS sheet sunk in box 1.12 mm thick with 2.8 mm thick laminated bakelite sheet all as specified & directed by Engr-in-charge for the following :- (a) One light/fan/Exhaust point controlled by one switch 5 Amp one way

-Ditto- all as per item no 109.but socket outlet 3pin 5 amps same board

-Ditto- all as per item no.109 but socket outlet 3pin 5 amps independent board

-Ditto- all as per item No.112 here-in-before but for one socket outlet/metal clad socket of 15 Amps fixed on independent board with 4.0 Sq mm multistranded copper conductor wire FRLS PVC insulated and 2.5 Sq mm copper conductor wire FRLS PVC insulated using as earth wire complete all as specified and directed by Engineer-in-Charge

M&L Modular white cover plate with frame ( both inner plate & outer plate cover ), 1 module.

M&L Modular white cover plate with frame ( both inner plate & outer plate cover ), 2 module.

M&L Modular white cover plate with frame ( both inner plate & outer plate cover ), 3 module.

M&L Modular white cover plate with frame ( both inner plate & outer plate cover ), 4 module.

M&L Modular white cover plate with frame ( both inner plate & outer plate cover ), 6 module.

Modular metal flush box 1 & 2 module

M&L Modular metal flush box 3 module

M&L Modular metal flush box 4 module

M&L Modular metal flush box 6 module

M&L Modular switch one way 6 Amp single pole & one modular.

M&L Modular socket 6 Amp 2/3 pin combined shattered ISI marked confirming to IS 1239 : 1997 having finger proof terminals with captive screws having front fixing & removing features without removing plates.

M&L Modular socket 16/6 Amp 2/3 pin combined 2 module shattered ISI marked confirming to IS 1239 : 1997 having finger proof terminals with captive screws having front fixing & removing features without removing plates.

M&L Modular switch 16 Amp single pole one way 1 moduly ISI marked confirming to IS 3854 : 1997 or latest IS having finger proof terminals with captive screws having front fixing & removing features without removing plates.

S&F for Electronic type modular fan regulator step type 120 watt, 230 volt. 02 module

S & F tube fixure/fitting 1x 20watt decorative ultra slim square profile with extruded polycarbonate, environmental friendly , energy eficient ready to use prewired for inclding connecting up with twin core twisted fiexible copper conductor cable with suitable size complete and all as specified and directed by Engineer- in Charge.”.

Supply & Fixing Ceiling fan 1200 mm sweep 50 Hz, single phase including down rod all as specified and as directed by Engr-in-charge

M/s Shri Inder Construction Company