Providing Security Cabin, Driver Room, PC Room and Additional Improvement Works to the Commissioners Quarters Campus at Ramakrishna Road in Division No.15, Salem Corporation.

Amount

Dismantling and Clearing away the existing Brick Work in Cement Mortar etc., complete.

Plain cement concrete 1:2:4 mix (One cement two CS sand and four aggregate) using 20mm size ISS gauge HBBG metal including mixing, laying, consolidating, curing, cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification

Removing and Refixing of Rubber Moulded Hydraulic Pressed Paver Block sizes 63 / 83mm thick to be laid in lorrying bone pattern with approved non sticking surface in the top and the rate including leveling the base, preparation of sub base with sand cushion 50mm thick, laying out the pavement, cut the pieces to fit the edge, vibrating the pavers, sweeping the sand grouting and laying of paver block as per standard specification.

Brick work in cement mortar 1:5 mix using Fly Ash bricks of 230x110x70mm (8 3/4" x 41/4" x 23/4") from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications

Flooring with ceramic tiles of approved Colour and quality of size 305mm x 305mm x 6mm in cement mortar 1:3 mix, 20mm thick and pointing with the same mortar etc., completely and finish very neatly.

Supplying and fixing MS grill to doors windows and ventilators etc. as directed by the departmental officers inclusive of cost of MS grill and labour charges including one coat of red oxide and fixing in position etc. complete

Roofing with Pre painted Galavalume sheet 0.47mm thick with necessary bolt and nuts and washers including allmaterials and labour charges etc complete

Providing Supply and Fixing of Fibre Sheet to the Main Gate Opening with necessary bolt and nuts and washers including allmaterials and labour charges etc complete

Supplying and fixing in position of Alu. Anodised Partition with 62x38x2mm extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90 cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4M height the bottom panels should be covered with 12mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick glass with necessary glassing clips. Rubber beading, etc., including necessary dismantling holes in RCC columns, beams masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the departmental officer. All the Aluminium sections should be anodised to 1.5microns as per ISI specification 1868/1962 and should be got approved by the Executive Engineer before use.

Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12 mm thick PLB board and 5.5 mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on both sides,floor stopper,Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections.All the materials should be got approved by the Engineer - In -charge before fixing as directed.

Aluminium Three Track window size 1.80 x 1.30m. Supplying and fabrication and fixing in position of anodised natural colour matt finish sliding window in three track in all floors with following sizes. All the three shutters with slinding arrangements, the bottom section should have Gutter arrangements so as to drain the water entering and made with extruded aluminium section for outer frames as shown below with necessary accessories such rubber beading. Aluminium clips, rubber beading,handle and fixing 4mm thick clear sheet glass including all required for fabrication etc., complete.Necessary dismantling making holes in RCC columns, beams, masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the departmental officers.The Al.Surfaces is to be anodised with matt finish under electrically condition in accordance with ISI 1868/1962 specification for an average anodic film thick of not less than 15 microns. (All materials should be got approved by the Executive Engineer before fixing in position)

Supplying, Fabricating and Fixing in Position of Ply wood & Prelaminated Sheeted Ornamental Kitchen Cub-Boards. Including Cost and Conveyance of Water Proof Ply Wood Sheets, Hinges, Screws, Lock, Handles, tower bolt, Inner Side patty & Painting work, Outer side Melamine Polishing work and Labour Charges etc., complete.

Supply and Fixing of Vinyl Floor Matt of 2mm thick including all cost and conveyance etc., complete.

Supply, Delivery and Installation of 16ch NVR Acusense, 32 Inch TV Hisense, WD 4TB HDD and 4U Rack with Power manager for CCTV Survilance Camera including all cost and conveyance etc., complete.

Providing Wall Putty including labour charges etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m

Painting two coats with best synthetic enamel paint of approved Colour for old iron works the rate is inclusive of all materials, brushes and scaffolding charges etc., complete complying with standard specification(paint should be got approved by the Departmental Engineer befor use on work.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of suitable colour for open PVC light point / fan point (for electronic regulator) SD-17

Wiring with 2 x 1.5 sq.mm (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 x 100 x 113mm TW switch box for 5A 3 pin non inter locking Wall socket with 5A flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point.

Wiring with 2 x 4 sq.mm. (56 / 0.3mm) PVC insulated SC unsheathed copper cable conductor cable of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with 150mm x 100mm x 75mm MS switch box for 15A 3 pin non interlocking CS plug with painting of suitable colour with continuous earth wire connection by 14 SWG TC wire for open power plug point

Supply and Fixing of Ornamental Gardening Light Fitting with LED Lamp etc., complete.

Supply and Fixing of Ornamental Gate Pillar Light Fitting with LED Lamp etc., complete.

Hayagreeva Earth Movers