Repaire of Link Road from Ruheri Noorpur Marg to Garhi Nandram U.M.S. Hathras.

Providing laying, spreading and compactong stone aggregates of specific sizes to water bound macadam specification including speading in uniform thickness, hand packing, rolling with three wheel roller 80-100 KN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 405.

Water Bound Macadam Sub-base (A) W.B.M. Grade-3 Providing laying spreading and compacting stone aggregates of specific size to water bound macadam, specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 Km in stages to proper grad and camber, applying and brooming stone screeing/binding materials to fill-up the interstices of coarse aggretate, watering and compecting to the required density grading 3 as Per Technical specification clause 405 (2)

CEMENT CONCRETE PAVEMENT(C.C ROAD) construction of un-reinforced plain cement concrete pavement thickness as per design, over a prepared sub base with 43 grade cement or any other type as per clause 1501.2.2 M 30 (grade) (1:1.5:3) coarse and fine aggregates conforming to IS 383 maximun size of coarse aggregate not exceeding 25mm mixed in a concrete mixer of not less then 0.2 cum capacity and appropriate weight batcher using approved mix design, laid in approved fixed side from work (steel channel laying and fixing of 125 micron thick plastic sheet, wedges steel plates including levelling the form work as per drawing) spreading the concrete with shovels, rakes compacted using needle, screed and plate vibrators and finished in continuous opration including provision of contraction and expansion construction joints applying debonding strips primer, sealant admixtures as approved curing concrete slabs for 14 days, curing compound (where specified) and water finishing to lines and grade as per drawing and technical specification (approved Quarri grit)

Brick soling with M-150 bricks laid on edge & dry brick edging on both side including preparation of subgrade to required camber and including supply of bricks filling joints with local earth spreading a blind coat of 1cm depth of local earth P.I. 5 to 7 or sand over the entire surface and including labour & T&P etc. required for proper completion of work or slop as per direction of E/I

Excavation in foundation in ordinary soil (Loam, Clay or Sand) Including lift upto 1.50 m & lead upto 30m & including filling watering & ramming of excavated earth into the trenches or into the space between the building & the sides of foundation trenches or into the plinth & removal & disposal of surplus earth as directed by the Engineer In-charge upto a distance of 30m from the foundation trenches. Excluding Royalty (SI 251)

Providing & laying cement concrete in 1:6:12 (1 cement : 6Course sand : 12 graded stone ballast 40mm nominal size) & curing complete, including cost of form work. In Foundation & floors. (SI 273) A

Class-150 brick work in 1:4 cement & Coarse sand of 1.25 fineness modulus mortar in foundation & plinth including supply of all material, labour & T&P etc. required for proper completion of the work. (SI 305)

12mm Cement plaster in single coat of fair side of single of half brick wall for interior plastering upto floor two level including internal rounded angles chamfers, and/or rounded angles not exceeding 80mm. In girth and finished even and smooth No. extra for mixing any additive. (II) 1cement : 4 coarse sand (as per SI 582) II

Providing and laying cement concrete in 4:2:1 of not less than strength of M-150 Stone grit (20 mm nominal size) approved coarse sand and cement, curing complete, Including cost of form work. In Foundation and floors. SI 279 (A)

Excavating, supplying and filling of local earth by mechanical transport upto a lead upto 5Km also including ramming and watering of the earth in layers not exceeding 20 cm in trenchs, plinth, of foundation etc. complete

Providing & fixing Typical informatory sign board asper MORD specification and drawing. Three M.S. plate of 1.6 mm thick, top and middle plate duty welded with M.S. flat iron 25mm x 5 mm size on back on edges. The lower plate will be welded with M.S angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of lower most plate and flat iron frame of middle plate will be welded to 2 Nos. 75mm x 75mm of 12 SWG sheet tubes post duly embedded in cement conc. M-15 grade black of 450mm x 450mm x 600mm below ground level. All M.S. will be stove enametat on both sides. Lettering and Printing arrows, border etc.will be painted with ready mixed sign thick enamd paints of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paints as per drawing clause 1701 and annexure 1700.

Maintainance of First Year (@0.00% of Total Work Amount of Part A

Maintainance of Second Year(@ 1.50% of Total Work Amount of Part A

Maintainance of Third Year(@3.00% of Total Work Amount of Part A

Maintainance of Fourth Year (@4.50% of Total Work Amount of Part A

Maintainance of Fifth Year (@6.00% of Total Work Amount of Part A

Please Enable Macros to View BoQ information