REPAIRS AND POLISHING OF CERTAIN WOODEN FURNITURE AND SOFA SETS INCLUDING TRADE PATTERN FURNITURE AT OFFRS MD ACCN UNIT LINES AND STORE YARD OF OF BSO SOUTH UNDER GE SOUTH BANGALORE

Amount

BED PLYWOOD TOP WITH MNF SET (Drg No.FD - 246 applicable to item nos. 01 to 05) Removing the existing unserviceable broken wooden long rail and supply of first class hard wood (Teak wood) new long rail of size 35mmx90mmx1980 mm including 35 mm x 5mm flat iron of mild steel bent to right angles as shown on drg and as as directed.

Removing the existing unserviceable broken wooden head board including legs and supply and fix 900x400mm new head board including teak wood legs of size 60mmx60mmx400mm and all as specified and as shown on drgs.

Removing the existing unserviceable /broken foot board including legs and supply and fix 900x300mm new foot board including teak wood legs of size 60mmx60mmx30mm and all as specified/directed and as shown on drg.

Removing the existing unserviceable /broken wooden stiffeners (supporting pieces) and supply and fix first class hard wooden stiffeners of size 40cmx60cm complete all as specified/directed and as shown on drg.

Removing the existing unserviceable plywood and supply and fix 900mmx1800mm x 12mm thick plywood commercial BWR grade bearing ISI marked all as specified/directed and as shown on drg.

SIDE BOARD (Drg No.FD - 241 - applicable to item nos. 06 to 14) Removing the existing unserviceable top and supply and fix new top of sizes 1220mmx455mm made out of 18mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination not less than 1.5mm thick complete all as specified/directed and as shown on drg.

Removing the existing unserviceable side and supply and fix new side made out of 18mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination not less than 1.5mm thick of sizes 760mmx455mm etc complete all as specified/directed and as shown on drg. Note:-Each side shall be measured as single units.

Removing the existing unserviceable back of side board and supply and fix new back of sizes 1220mmx700mm with 6mm thick plywood, grade BWR, type BB with no. of ply 5, ISI marked all as specified/directed and as shown on drg.

Removing the existing unserviceable bottom of drawer and supply and fix new bottom drawer of size 380mmx450mm,12mm thick plywood, grade BWR, type BB with no. of ply 7 all as specified/directed and as shown on drg.

Removing the existing unserviceable drawer and supply and fix new drawer of size 380mmx450mmx155mm, made out of teak wood plank 12 mm thick for sides and back and 18mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for front and 6mm thick plywood for bottom of drawer, including fittings such as knobs etc all as specified/directed and as shown on drg. Note:-Each drawer will be measured as single unit.

Removing the existing unserviceable shutter and supply and fix new shutter of size 600mmx390mm made out of 18mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, including hinges, kobs and lock all as specified/directed and as shown on drg. Note:- Each shutter will be measured as single unit.

Removing the existing unserviceable bottom of side board and supply and fix new bottom of sizes 455mmx1228mm, made out of 18mm thick plywood, grade BWR, type BB all as specified/directed and as shown on drg.

Removing the existing unserviceable leg frame and supply and fix new teak wood leg frame with legs, sizes 1140mmx 380mm, etc complete all as specified/directed and as shown on drg..

Removing the existing unserviceable broken wooden legs and supply and fix new teak wood leg, size 45mmx45mmx125mm etc complete all as specified/directed and as shown on drg. Note:- Each leg will be measured as single unit.

TABLE WRITING (Drg No. FD-249 FD-33 FD-275 applicable to item nos. 15 to 20) Removing the existing unserviceable broken top and supply and fix new top made out of 18mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick teak wood edging, size 1145mmx600mm all as specified/directed and as shown on drg.

Removing the existing unserviceable/ damaged cupboard shutter and supply and fix new shutter made out of 18 mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, size 400mmx700mm, including piano hinges and brass lock all as specified/directed and as shown on drg.

Removing the existing unserviceable drawer and supply and fix new drawer size 300mmx600mmx75mm, made out of teak wood plank 12 mm thick for sides and back and 18mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for front and 6mm thick plywood for bottom of drawer (Plywood, grade BWR, type BB with no. of ply 5) including fittings such as knobs etc all as specified/directed and as shown on drg. Note:- Each drawer will be measured as single unit.

Removing the existing unserviceable back and supply and fix new back size 1145mmx700mm, made out of 6mm thick Plywood grade BWR, type BB, no. of ply 5, with two coats of synthetic enamel paint over a coat of primer all as specified/directed and as shown on drg.

Removing the existing unserviceable side and supply and fix new side size 600mmx700mm, made out of prelaminated particle board, 18mm thick exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination all as specified/directed and as shown on drg. Note:- Each side will be measured as single unit.

Removing the existing unserviceable leg and supply and fix new teak wood leg size 35mmx55mmx717mm, etc complete all as specified/directed and as shown on drg.

TABLE DINING 6 PERSONS 1500mm x 900mm (Drg No. FD-273 FD-239 - applicable to item nos. 21 to 24) Removing the existing unserviceable damaged top and supply and fix with a new prelaminated particle board 18mm with 6 mm thick teak wood edging all round of size 1500mmx900mm all as specified/directed and as shown on drg.

Removing the existing unserviceable damaged front and back rails & supply and fix new teak wood front and back rails of size 25mmx100mmx1500mm all as specified/directed and as shown on drg

Removing the existing unserviceable damaged leg and supply and fix new teak wood leg of size 75mmx40mmx760mm all as specified/directed and as shown on drg .

Removing the existing unserviceable damaged side rails and supply and fix new teak wood side rails of size 25mmx100mmx900mm all as specified/directed and as shown on drg.

TABLE DINING 8 PERSONS 1800mm x 900mm (Drg No. FD-273 FD-239 - applicable to item nos. 25 to 28) Removing the existing unserviceable damaged top and supply and fix new top with a new prelaminated particle board 18mm with 6 mm thick teak wood edging all round of size 1800mmx900mm all as specified/directed and as shown on drg..

Removing the existing unserviceable damaged front and back rails & supply and fix new teak wood front of size 15mmx100mmx1800mm and back rails all as specified/directed and as shown on drg..

Removing the existing unserviceable damaged leg and supply and fix new teak wood leg all as specified and as shown on drg of size 75mmx40mmx700mm.

Removing the existing unserviceable damaged side rails and supply and fix new teak wood side rails of size 25mmx100mmx900mm all as specified and as shown on drg .

TABLE PEG (Drg No. FD-384 FD-25 FD-236 - applicable to item nos. 29 to 32) Removing the existing unserviceable top and supply and fix new top of size 450x300 mm made out of 18mm thick pre-laminated particle board and 4mm thick teak wood edging round the top of table all as specified and as shown on drg.

Removing the existing unserviceable bottom rail and supply and fix new teak wood bottom rail of size 20x 40x300mm all as specified and as shown on drg.

Removing the existing unserviceable front/back rail and supply and fix new teak wood front/back rail of size 20x 40x450mm all as specified and asshown on drg.

Removing the existing unserviceable leg and supply and fix new teak wood leg of size 30x50x380 mm all as specified and as shown on drg.

TABLE CENTRE (Drg No. FD-29 FD-274 FD-235 - applicable to item Nos 33 to 36) Removing the existing unserviceable top and supply and fix new top of size 900mm x 450mm made out of 18mm thick pre laminated particle board and provided 4mm thick teak wood beading alround of table top all as specified and as shown on drg.

Removing the existing unserviceable leg and supply and fix new teak wood leg of size 30mmx60mmx400mm all as specified and as shown on drg.

Removing the existing unserviceable long rail of size 30mmx60mmx900mm and supply and fix new teak wood long rail all as specified and as shown on drg.

All as per item Ser no 35 here-in-before but short rail of size 30mmx60mmx450mm.

TABLE DRESSING WITH MIRROR LADIES (Drg No. FD-32 FD-251 - applicable to item nos. 37 to 44) Removing the existing unserviceable drawers and supply and fix new drawers of size 300mmx380mm, 3 Nos & 315mmx115mm, 2 Nos made out of teak wood plank 12mm thick for sides/ back and 18 mm thick pre-laminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for front and 6 mm thick plywood, grade BWR, type BB with no. of ply 5 for bottom of drawers, including fittings such as knobs etc all as specified and as shown on drg. Note:-Each drawer shall be measured as single unit.

Removing the existing broken glass shutters and supply and fix new glass shutters of size 300mmx390mm, 2 Nos, 5mm thick all as specified and as shown on drgs. Note:- Each glass shutter will be measured as single unit.

Removing the existing unserviceable aluminium channel and supply and fix new aluminium channel of width 10mm, 1mm thick suitable for the drawer of size 530mm long all as shown on drgs.

Removing the existing unserviceable plywood portion from back of mirror and supply and fix new back with frame of mirror of size 395mmx1230mm made out of 6 mm thick plywood, grade BWR, type BB with no of ply 5 all as specified and as shown on drgs.

Removing the existing unserviceable mirror and supply and fix new mirror of size 365mmx1220mm, 5 mm thick complete with frame and back all as specified and shown on shown on drgs.

Removing the existing unserviceable 12mm ply wood from back and supply and fix new back of size 395mmx900mm of table dressing ladies made out of 12 mm thick plywood commercial quality all as specified and as shown on drgs.

Removing the existing unserviceable frame with legs and supply and fix new teak wood frame with 4 legs short frame of size 235mmx40mmx25mm, 2 nos & and long frame of size 650mmx40mmx25mm, 2nos and leg of size 155x45x45mm all as specified and shown on drgs.

Removing the existing unserviceable leg and supply and fix new leg made out of teak wood of size 155x45x45mm, 4 nos all as specified and as shown on drgs. Note:- Each leg shall be measured as single unit.

TABLE DRESSING WITH MIRROR GENTS (Drg No. FD-31 FD-230 - applicable to item nos. 45 to 49) Removing the existing unserviceable top of table dressing Gents and supply and fix new top of size 900mmx300mm made out of 18 mm thick pre laminated particle board all as shown on drgs

Removing the existing unserviceable bottom of table dressing Gents and suplply and fix new bottom of size 900mmx300mm made out of 18 mm thick plywood commercial quality all as shown on drgs.

Removing the existing unserviceable side partition and supply and fix new side partition of size 300mmx135mm, 2 nos made out of 18mm thick pre-laminated particle board all as shown on drg. Note : Each side or partition shall be measured as single unit.

Removing the existing unserviceable drawers of size 280mmx130mm, 4 nos of table dressing Gents and supply and fix new drawers made out of teak wood plank 12mm thick for sides and back and 18 mm thick pre-laminated particle board for front and 6 mm thick plywood for bottom of drawers with fitting such as knobs etc all as specified and as shown on drg. Note : Each drawer shall be measured as single unit.

Removing the existing unserviceable mirror and supply and fix new mirror of size 390mmx760mm, 5 mm thick with back and frame all as specified and as shown on drgs including with teak wood support all as shown on drgs.

TABLE 900X600 WITH DRAWER (Drg No. FD-41 FD-283 FD-224 - applicable to item nos. 50 to 53) Removing the existing unserviceable table top and supply and fix new top of size 900mmx600mm of prelaminated particle board 18mm of size interior grade with 4mm thick teak wood edging all round all as specified and as shown on drgs.

Removing the existing unserviceable/damaged front and back rails and supply and fix new teak wood front and back rails of size 25mmx130mmx740mm all as specified and as shown on drg.

Removing the existing unserviceable damaged leg and supply and fix new teak wood leg of size 60mm to 40mm(bottom) with a height of 735mm all as specified and as shown on drg.

Removing the existing unserviceable damaged side rails and supply and fix new teak wood side rails of size 25mmx130mmx440mm all as specified and as shown on drg.

TEAPOY (Drg No. FD-34 FD-278 FD-232 FD-382 - applicable to item nos. 54 to 57) Removing the existing unserviceable top and supply and fix new top of size 600mmx450mm made out of 18mm thick pre-laminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination with 4mm thick teak wood edging al-round the top of teapoy all as specified and as shown on drg.

Removing the existing unserviceable leg and supply and fix new teak wood leg of size 515mmx45mmx45mm all as specified and as shown on drg.

Removing the existing unserviceable front rail and supply and fix new teak wood front rail of size 450mmx50mmx20mm all as specified and as shown on drgs.

Removing the existing unserviceable side rail and supply and fix new teak wood side rail of size 390mmx50mmx20mm all as specified and as shown on drgs.

Book case (Drg No.FD-237) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/abbrassive cloth throughly smooth and clean off and applying one coat of french polishing to required finish complete all as specified and as directed.

Side Board (Drg No.FD-241) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table 900x600 with Drawer (Drg No. FD-41 FD-283 FD-224) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table bed side (Drg No. FD-28 FD-276 FD-243) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table Dressing Gents (Drg No. FD-31 FD-230) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table Dressing Ladies (Drg No. FD-32 FD-251) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Bed plywood top (Drg No. FD-246) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Binsoiled linen large (Drg No. FD-70) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Chair dining (Drg No. FD-16 FD-279) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Chair dining Map (Drg No. FD/MAP II/04) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Chair Easy (Drg No. FD-17 FD-229) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Chair writing (Drg No. FD-20 FD-280) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Hat stand with mirror (Drg No. FD-233) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Peg table (Drg No. FD-384 FD-25 FD-236) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Sofa Set 4 Seater (Drg No. FD-258) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying ono coat of french polish to required finish complete all as specified and as directed.

Sofa Set 5 Seater (Drg No. FD-281) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Stool Dressing (Drg No. FD-27) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table 900x600 W/o Drawer (Drg No. FD-284 FD-42) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table Centre (Drg No. FD-29 FD-274 FD-235) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table dining 6 persons (Drg No. FD-273 FD-239) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table dining 8 persons (Drg No. FD-273 FD-239) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table office clerk wooden (Drg No. DB-2201) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table office officer wooden (Drg No. DB-4199) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table writing (Drg No. FD-249 FD-33 FD-275) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Teapoy (Drg No. FD-34 FD-278 FD-232 FD-382) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Almirah large wooden with shelves (Drg No. DB-4042) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/abbrassive cloth throughly smooth and clean off and applying one coat of french polish of the required finishing complete all as specified and as directed.

Almirah med wooden with shelves (Drg No. DB-3959) Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/abbrassive cloth throughly smooth and clean off and applying one coat of french polish of the required finishingcomplete all as specified and as directed.

SOFA SETs (Drg No. FD-281 - applicable to item nos. 85 to 93) Removing the existing unserviceable tapestry cloth, cushion and replacing with new tapestry cloth as per sample with foam cushion of size 560mmx530mm, 40 density, 100mm thick, including inner long all as shown on drgs and as directed. Note :- Each cushion for seat or back will be measured as single unit.

Removing the existing unserviceable leg from sofa and supply and fix new teak wood leg of size 510mmx75mmx35mm all as shown on drg and as directed.

Removing the existing unserviceable arm rest from sofa and supply and fix new teak wooden arm rest of size 750mmx70mmx35mm all as shown on drawing and as directed .

Removing the existing unserviceable side rail from sofa and supply and fix new teak wood side rail of size 690mmx100mmx35mm all as shown on drawing and as directed .

Removing the existing unserviceable bearer from sofa long pieces and supply and fix new teak wood bearer of size 590mmx50mmx22mm all as shown on drawing and as directed .

Removing the existing unserviceable bearer from sofa short pieces and supply and fix new teak wood bearer of size 440mmx50mmx22mm all as shown on drawing and as directed .

Removing the existing unserviceable battens from sofa and supply and fix new teak wood battens of size 570mmx50mmx22mm all as shown on drawing and as directed .

Removing the existing unserviceable front rail from sofa long pieces and supply and fix new teak wood front rail all as shown on drawing and as directed .

Removing the existing unserviceable front rail from sofa short pieces and supply and fix new teak wood front rail of size 22mmx102mmx1740mm all as shown on drawing and as directed .

SOFA Set (Drg No. FD-258 - applicable to item nos. 94 to 101) Removing the existing unserviceable tapestry cloth, cushion and replacing with new tapestry cloth with foam cushion 40 density, 50 mm thick all as shown on drgs and as directed. Note:- Each cushion for seat or back will be measured as single unit. Tapestry cloth to be provided as per sample.

Removing unserviceable plywood 12 mm from seat of sofa set and fix new plywood 12 mm ISI marked BWR grade of size 670mm x 690mm for chairs and as specified in drg

Removing unserviceable Plywood 12 mm from seat of sofa set and fix new plywood 12 mm ISI marked BWR grade of size 1740mmx 690mm for chairs and as specified in drg

Removing the existing unserviceable front leg from Sofa and supply and fix new teak wood leg of size 30mm x 75mm x 510mm all as shown on drg and as directed.

Removing the existing unserviceable back leg from Sofa and supply and fix new teak wood leg of size 30mm x 75mm x 760mm all as shown on drg and as directed.

Removing the existing unserviceable wooden front bearer from Sofa and supply and fix new teak wood front bearer of size 20mm x 50mm x 1740mm all as shown on drg and as directed

Removing the existing unserviceable side rail from Sofa and supply and fix new teak wood side rail of size 30mm x 102mm x 690mm all as shown on drg and as directed.

Removing the existing unserviceable back support rail from sofa and supply and fix new teak wood back support rail of size 20mm x 102mm x 1740mm all as shown on drg and as directed.

Chair Computer/Chair Revolving (Drg No. FD/E6/MAP/01) Removing the existing un serviceable seat (cushioned) and supply and fix the new seat of seat 510mm x 470mm x 60mm (12 mm hot pressed ply wood, upholstered with fabric and moulded polyurethane foam with PVC lipping for chair computer/chair revolving all as shown on drg and as directed. (Make : Godrej or equivalent)

Chair cushion with arms/chair visitor (Trade Pattern) Removing the existing un serviceable seat (cushioned) and supply and fix the new seat of seat 510mm x 470mm x 60mm (12 mm hot pressed ply wood, upholstered with fabric and moulded polyurethane foam with PVC lipping for chair cushion with arms/chair visitor all as shown on drg and as directed.

Chair revolving padded with arm high back (Drg No. FD-75) Removing the existing un serviceable seat (cushioned) and supply and fix the new seat of seat 510mm x 470mm x 60mm (12 mm hot pressed ply wood, upholstered with fabric and moulded polyurethane foam with PVC lipping for chair revolving padded with arm high back all as shown on drg and as directed.

Chair computer/Chair revolving (Drg No. FD/E6/MAP/ 01) Removing the existing un serviceable back and supply and fix the new back (12 mm th hot pressed ply wood, upholstered with fabric and moulded polyurethane foam. The back form shall be designed with contour lumber support for extra comfort with PVC lipping for Chair computer/Chair revolving approx size of seat 510mm x 470mm x 60mm.all as shown on drg and as directed. (Make : Godrej or equivalent)

Chair Cushion with arms (Trade pattern) Removing the existing un serviceable back and supply and fix the new back (12 mm th hot pressed ply wood, upholstered with fabric and moulded polyurethane foam. The back form shall be designed with contour lumber support for extra comfort with PVC lipping for chair cushion with arms all as shown on drg and as directed.

Chair revolving padded with arm high back (Drg No. FD-75) Removing the existing un serviceable back and supply and fix the new back (12 mm th hot pressed ply wood, upholstered with fabric and moulded polyurethane foam. The back form shall be designed with contour lumber support for extra comfort with PVC lipping for chair revolving padded with arm high back all as shown on drg and as directed.

Chair Computer/Chair Revoving/Chair Steel (TP) Supply and fix in repair new bottam gas lift (Hydraulic) with Pocuch of size 38 mm dia 2mm thick for revolving charis and computer charis. It shall have 100 mm stroke length and gass prssure of 300 force. Note adjustable titiing mechanism to prevent back rest from hitting the user when the lock released, 360 swivel mechanism to allow fluid lateral movement all as directed.

Removing the existing unserviceable broken twin casterwheel form revolving chairs and computer chairs and supply and fix new fibre caster wheel II complete all as directed. Make : Godrej or equivalent

Supply and fix in repairs new pedestal assembly injection moulded in back 30% glass filling nylone a 10.5 mm dia forget bright zinc plated MS Caster pin is of press fitting in to each prong holding the castors. It is 600 mm opitch, centre dia from revolving chairs and computer chairs all as directed. Make : Godrej or equivalent

Removing the existing unserviceable broken padded arm rest and supply and fix new arm rest (black integral skin polyurethane finforced with MS insert), scratch and weather resistant type from revolving chairs and computer chairs complete all as directed. Make : Godrej or equivalent

Global Furnisherts