PROVN OF CERTAIN SANCTIONED WORKS AT PATIALA UNDER GE(SOUTH) PATIALA

Amount

LUMPSUM/ OTHER PRE-PRICED PROVISIONAL SCHEDULES OF WORKS

Lump sum price worked out by the contractor for BUILDING WORK as listed in Schedule 'A' Sec-I.

Lump sum price worked out by the contractor for INTERNAL WATER SUPPLY as listed in Schedule 'A' Sec-II.

Lump sum price worked out by the contractor for PATH/ SUB BASE OF FLOOR WORKS as listed in Schedule 'A' Sec-III.

Lump sum price worked out by the contractor for INTERNAL ELECTRIFICATION WORKS as listed in Schedule 'A' Sec-IV.

Lump sum price worked out by the contractor for EXTERNAL WATER SUPPLY as listed in Schedule 'A' Sec-V.

Lump sum price worked out by the contractor for SEWAGE DISPOSAL WORKS as listed in Schedule 'A' Sec-VI.

Lump sum price worked out by the contractor for EXCAVATION AND EARTH WORKS as listed in Schedule 'A' Sec-VII.

SCHEDULE 'A' SEC-VIII – Misc Items

M&L Brick work with Fly ash bricks minimum class designation 100 straight or curved on plan exceeding 6m mean raidus bulit in C:M 1:6 complete all as specified and directed.(TD=12, TE=13, SRW=13)

M&L for Brickwork with flyash bricks minimum class designation 100, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 in half brick thick walls complete all as specified and directed. (TD=5.7, TE=5.7, SRW=11.4)

M&L for Reinforced Cement Concrete (RCC) 1:2:4 using 20mm graded stone aggregates as in Beams, cantilevers, bressummers, lintels, roof bands, lintel band over 1.5m span complete all as specified and directed. (TD=1.3, TE=1.3, SRW=2)

M&L for Reinforced Cement Concrete (RCC) 1:2:4 using 20mm graded stone aggregates as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. (TD=1.8, TE=1.8)

M&L for Form work rough finished to sides and soffits of beams/ lintel bands/ roof bands/beams and the like structures complete all as specified. (TD=11.5, TE=11.5, SRW=45)

M&L for form work rough finished to soffits of suspended slabs such as roof slabs not exc 200mm thick (Horizontal or sloping) complete all as specified and directed. (TD=12, TE=12)

M&L for form work rough finished to edges of concrete slabs exc 10 cm but not exc 20 cm thick complete all as specified and directed. (TD=16.10, TE=16.10)

M&L for TMT Bars 10mm dia & over cut to length, bent to shape required including cranking, bending spirally hoping for columns, hooking ends and binding with mild steel wire not less than 0.9 mm dia complete all as specified and directed. (TD=271.8, TE=271.8, SRW=170)

M&L for TMT Bars 6 to 8mm dia cut to length, bent to shape required as in stirrups hooking ends and binding with mild steel wire not less than 0.9 mm dia complete all as specified and directed. (TD=73.6, TE=73.6, SRW=50)

M&L for pre-polished Baroda Green marble, machine cut as in floorings/ shelves/ steps/ cills/ jambs/ skirting/ border only in tile flooring and the like works and flooring etc, 15-16 mm thick including bull-nose the exposed sides/lengths, set and jointed in cement slurry over & including screed of 15 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab for fixing on concrete surfaces or with suitable adhesive for fixing on un-polished kota stone slabs including rubbing, cutting and mirror type granite polishing complete all as specified and directed. Note : Single piece should be used in steps/cills/jambs/shelves. (TD=1, TE=1)

M&L for 5 mm thick cement plastering in cement mortar 1:3 on fair faces of concrete ceiling surfaces finished fair & even without using extra cement complete all as specified and directed. (TD=11.4, TE=11.40)

M&L for cement plastering 15mm thick in two layers in cemet mortar 1:4 including mixing of liquid water proofing compound as per manufacturer's instructions on brick work or concrete surfaces or in chajjas/parapet walls etc finished even and fair without using extra cement complete all as specified and directed. (TD=40.1, TE=40.1, SRW=150) Note : WPC will be measured and paid separately.

Supply only integral liquid water proofing compound complete all as specified and directed. (TD=1.5, TE=1.5, SRW=6)

M&L for preparation of surfaces and applying 02 coats of interior emulsion paint (light shade) @ 10 sq.m/litre/2 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed.(TD=9.3, TE=9.3)

M&L for preparation of surfaces and applying 02 coats of interior emulsion paint (white shade) @ 10 sq.m/litre/2 coats to ceilings surfaces over & including a coat of interior primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed.(TD=11.4, TE=11.4)

M&L for preparation of surfaces and applying 02 coats of exterior emulsion paint (light shade) with highlighter of any approved shade, @ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed (TD=40.1, TE=40.1, SRW=150)

M&L for mat finish anti skid ceramic tile joint free premium quality coloured tiles 300 X 300 mm and 6-8 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 20 mm thick screed in cement mortar (1:4) over and pointed in white cement with pigment to match the colour of tiles complete all as specified. (TD=7.1, TE=7.1)

M&L for ceramic glossy finish, joint free premium quality coloured tiles 600 X 300 mm and 7-9 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified. Note : Dado should be flushed with the wall plastering. (TD=32, TE=32)

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50 mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints and filling the same with polyureathene complete all as specified. (TD=8.6, TE=8.6, SRW=54)

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardan and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. (TD=10, TE=10)

S&F 50 micron powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. (TD=30, TE=30, SRW=52)

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per drawings complete all as specified and directed. (TD=20, TE=20)

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per drawings complete all as specified and directed (TD=20, TE=20, SRW=50)

S&F aluminium alloy anodised extruded fabricated type handle 150mm long complete all as specified and directed. (TD=4, TE=4, SRW=12)

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) 300 mm long fixing clips of sheet cast or and fixing with bolts extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed. (TD=2, TE=2)

S&F aluminium alloy, anodised, barrel tower bolt (bolt type) 200 mm long of extruded section or cast aluminium alloy and fixed complete all as specified and directed. (TD=4, TE=4, SRW=6)

M&L for 5mm thick frosted glass in ventilators/ windows/ doors fixed in any metal frame work complete all as specified and directed. (TD=1, TE=1)

S&F 12mm thick high Density High Moisture Resistant (HDHMR) exterior Grade Board with one side designer laminate (OSL) of approved colour and finishing and other side white balancing with density of 850 Kg/cu.m complete all as specified and directed. (TD=1, TE=1)

S&F Stainless steel wire cloth, Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. (TD=2, TE=2)

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in lintels upto 1.50 m clear span, cills , steps, seismic and other similar bands, copings, kneelars, apex stones, bed plates, bed blocks of hold fasts etc including necessary for R.M. work complete all as specified and directed. (TD=0.5, TE=0.5)

M&L for providing and laying 3mm thick APP (Atactic Polypropylene Polymer) modified prefabricated five layer, weight not less than 3.6 Kg/Sqm water proofing membrane black finished, reinforced with non-woven polyester matt make as approved including of a coat of bitumen primer confirming to IS-3384 and as described at para 11.44.5 of MES Schedule Part-I @ 0.40 ltr/sq.m by the same membrane manufacturer of density 0.87 to 0.89 Kg/Ltr at 25 degree C temperature and viscosity 70 - 160 cps Over the coat, 3mm thick 5 layered APP membrane shall be laid using butane torch and sealing all joints etc after the surface complete as per standard practice as per manufacturers instructions including 15mm thick cement plaster (1:3) using coarse sand mixed with integral liquid water proofing compound shall be provided while the concrete of roof slab is green and finishing surface even and smooth with steel trowel complete all as specified and directed. Note : The vital physical and chemical parameters of the membrane shall be as under - (i) Joint strength longitudinal and transverse direction at 23 degree C as 650/450N/5cms (ii) Tear strength in longitudinal and transverse direction as 300 / 250 N/. Softening point of membrane not less than 150 degree C Cold flexibility upto 20 degree C when tested in accordance with ASTM (D05147) (iii) The laying of membrane shall be got done through the authorised applicator of manufacturer of membrane only complete all as specified and directed. (TD=12, TE=12)

M&L for Plain Cement Concrete tiles 25cm x 25cm x 22-25mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished laid over 15mm thick screed bed in CM 1:4 complete all as specified and directed (TE=10.8)

S&F ISI marked doubled layered rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top / cover) 1000 Ltrs capacity hoisted and fixed in position all as specified including 20 mm dia brass float valves, high pressure, with polythene float and fly nut complete screwed for 20mm bore iron pipe and including GI nipple/union of 20mm bore to connect GI tubing to PVC water tank complete all as specified and directed. (TD=1, TE=1)

S&F Cast iron sand cast soil waste & vent pipe in any length with or without ears with cement joints fixed to walls 100mm running bore in and including stack clamps, nuts bolts etc and making necessary connections, complete all as specified and directed. (TD=5, TE=5)

S&F Cast iron sand cast soil waste & vent pipe in any length with or without ears with cement joints fixed to walls 75mm running bore in and including stack clamps, nuts bolts etc and making necessary connections, complete all as specified and directed. (TD=5, TE=5)

S&F Cast iron sand cast soil waste & vent pipe 100mm bore in any length with or without ears with cement joints laid in trenches or in floor complete all as specified and directed. (TD=3, TE=3)

S&F Cast iron sand cast soil waste & vent pipe 75mm bore in any length with or without ears with cement joints laid in trenches or in floor complete all as specified and directed. (TD=3, TE=3)

S&F Stack clamps for 100mm bore CI pipes made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed. (TD=5, TE=5)

S&F CI bends 100mm bore pipes (any radius) diminishing pieces or tapers (larger bore measured) without oval access door complete all as speciied and directed. (TD=1, TE=1)

S&F CI bends 75mm bore pipes (any radius) diminishing pieces or tapers (larger bore measured) without oval access door complete all as speciied and directed. (TD=1, TE=1)

S&F Cl bend 100mm bore pipes (any radius) with oval access door of 100 mm bore fixed complete all as specified and directed.. (TD=1, TE=1)

S&F Cl bend 75mm bore pipes (any radius) with oval access door of 75 mm bore fixed complete all as specified and directed.. (TD=1, TE=1)

S&F Cast iron cowls for 100mm bore pipes complete all as specified and directed. (TD=1, TE=1)

S&F CI double branch door Tee suitable for 100mm bore pipes ISI marked complete all as speciied and directed. (TD=1, TE=1)

S&F CI plain Tee suitable for 100mm bore pipes ISI marked complete all as speciied and directed. (TD=1, TE=1)

Cast iron bends duck foot or heelrest, radius for 100 mm bore pipe, as in repairs, complete all as specified and directed. (TD=1, TE=1)

M&L for Cast iron floor trap/nahani with long arm of min 450mm length, with dia of outlet 100mm including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed. (TD=3, TE=3)

S&F PVC(HDPE) SWR , 40 mm bore, single socketed in any length with rubber ring joints using solvent as per maunfacture instruction, including S&F of bends/fittings as required and fixed to walls incl cutting chases if required for concealed water tubing and making good, cutting not exc 10 cm girth etc complete all as specified and directed. (TD=3, TE=3)

S&F 5mm thick looking mirror fixed to wall with stainless steel plugs/connecter/spacers/screws etc. chrome finish without any beading, including ends/edges of the mirror to be tapered/bevelled edge etched smooth finish etc.complete fixed in position all as specified and directed. (TD=2, TE=2)

S&F CP finished towel ring square shaped of size 135 x 195 mm including all accessories like wall flange/ cup fixed with suitable PVC wall plugs & screws of make cera (Cat. No. F5013115CH) or equivalent make mentioned hereinafter as per manufacturer's instructions complete all as specified. (TD=1, TE=1)

S&F soap dish CP plated of suitable size to accommodate soap complete all as directed and specified. (TD=1, TE=2)

S&F stainless steel grating 125 x 125 mm size square shaped with self locking arangement for floor trap fixed in position complete all as specified and directed. (TD=3, TE=3)

S&F CP bottle traps 32mm size with 250mm and 175/190mm long wall connection pipes and wall flanges complete fixed in position complete all as specified and directed. (TD=1, TE=1)

S&F CP waste couplings 32mm size full thread with 80mm height complete fixed in position complete all as specified and directed. (TD=2, TE=2)

S&F Self closing angle cock pressmatic for urinal with wall flange and 200 mm connecting pipe make cera (Cat. No. F9020203) or equivalent make mentioned hereinafter complete all as specified and directed. (TD=1, TE=1)

S&F urinal spreader for urinals and incl all necessary accessories as recommended by manufacturer for fixing complete in all respect all as specified and directed. (TD=1, TE=1)

S&F PVC(HDPE) SWR , 32 mm bore, single socketed in any length with rubber ring joints using solvent cement as per maunfacture instruction, including bends/tee/elbow etc. laid in walls for connecting bottle traps complete all as specified and directed. (TD=2, TE=2)

S&F vitreous china premium/1st quality wash down water closet pan floor mounting (pedestal pattern/EWC) with S/P trap snow white colour of size 520X360X390mm including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc.,with flush pipe and incl. S&F plastic seat cover as recommended by manufacturer closed pattern with flat bottom etc; and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer complete in all respect and all as specified and directed. Note : EWC with S trap will be provided only on G.F. and other remaining floors will be provided with P trap EWCs. (TD=2, TE=1)

S&F Health faucet (ABS Body) with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed. (TD=2, TE=1)

S&F flushing cistern of Polymer/PVC 10 ltr. cap. with dual flushing system, white colour, valveless syphonic action type, , low level, with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer complete in all respect and all as specified and directed. (TD=2, TE=1)

S&F vitreous china premium/1st quality wash basin (under counter oval shaped), snow white, size 560x470x190 mm including all accessories of make cera (Cat. No. S2030104) or equivalent make mentioned hereinafter as recommended by manufacturer complete fixed in position in all respect as per manufacturer's instructions and all as specified Note : The items for counter will be measured and paid separately. (TD=1, TE=1).

S&F Vitreous China Urinal 330 x 300 x 450 mm, Half stall type, snow/star white including fixing plug, Cast Iron Bracket duly painted/Erecting Stand including cutting, CP 32mm flush pipe etc all fittings of make Hindware (Corto Cat. No. 60023) or euivalent make mentioned hereinafter complete all as specified and directed. (TD=1, TE=1).

M&L for applying acrylic thick wall care putty on internal/external surfaces of walls/ceilings/soffits (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed. Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order. (TE=20.70, SRW=250)

S&F CP/matt finished peg set of size 300mm long and 30mm wide with 6 nos hooks of approved quality fixed with suitable screws complete all as specified and directed. (TD=1, TE=1)

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed.(SRW)

Dismantling timber scantling in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section , unframed work in any position complete all as specified and directed.(SRW)

Dismantling/ Taking down framed wooden trusses exceeding 8.00m span but not exceeding 12.00 m span and removimg from site complete all as specified and directed.(SRW)

Dismantling of Brick work including all quains and arches pillars etc built in cement mortar complete all as specified and directed.(SRW)

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.(SRW)

M&L for Removing old lime wash (if any), hacking for key, raking out joints of old brick work or stone work built in lime or mud mortar; not previously plastered; and scrubbing down with water etc. to receive plaster complete all as specified and directed.(SRW)

M&L for 10mm thick cement plastering in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.(TD=9.3, TE=9.3, SRW=170)

Supplying & applying for two component elastomeric acrylic polymer modified cementitious waterproofing coating on Brick level, SmartCare Damp Block 2K or approved equivalent (For Effloresce treatment), having 100% elongation as per ASTM D412, resisting 5 bars hydrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per ASTMC1202, crack bridging up to 1.2mm as per ASTM 4548.5. The coating shall have food grade certificate from laboratories like CFTRI, will be apply on both Positive & Negative side and resist up to 5 Bars of Hydrostatic Pressure. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc. After coating sand will be sprinkled on the coating then apply plaster on the coating including all type of scaffolding etc as required complete as manufacturer specifications and as specified and directed. Note : Taking down cement plaster and rendering plaster will be measured and paid separately. (SRW)

M&L for complete removal of existing treatment of any type/description from walls/RCC surfaces/ ceiling/ chajjas/ roof projections etc with mechanical means/grinder or manually complete all as specified and directed.(SRW)

M&L for preparation of newly plastered Surfaces of wall apply two coats of oil bound distamper white or tinted, over and including a coat of primer complete all as specified and directed.(SRW)

Demolition of cement concrete un -reinforced in ground floors and pavings n.exc 15cm thickness complete all as specified and directed.(SRW)

M&L for 100mm thick cement concrete work 1:4:8 type D-2 in base of flooring etc complete all as specified and directed.(SRW)

Dismantling, floor, hearth or wall tiling including CM bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and directed(SRW)

M&L for machine cut kota stone slab (nearest to 58cmx58cm in size) flooring 18mm (+ 2mm) thick laid over and including 20-22 mm thick screed bed or bedding layer in cement mortar 1:4 as base laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing incl 100mm wide border of Baroda Green Marble complete all as specified and directed.(SRW)

M&L for Polished Glazed Vitrified Tiles (PGVT) joint free premium quality coloured tiles 600 X 1200 mm and 8-10 mm thick, as in skirting/dado etc. laid with 3-5mm spacers and grooves shall be filled with epoxy grout (Pidilite or equivalent) of approved matching colour. in any pattern of light & dark tiles as approved, laid and jointed in suitable adhesive (flexiset H-40 or equivalent as approved) as per manufacturer's instructions and pointed in matching coloured cement based tile joint filler (Roff -Pidilite or equivalent as approved), in floors etc. over & including 10 mm thick screed in cement mortar (1:4) over complete all as specified and directed. Note : The rates for labour and material for spacers/ grovers shall be deemed to be included in the quoted unit rates and nothing shall not be measured & paid separately on this account.(SRW)

M&L for coloured ceramic tiles joint free premium quality Kota colour/any colours tile 600 X 300 mm and 8-10 mm thick, as in skirting etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 10 mm thick rendering in cement mortar (1:6) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.(SRW)

M&L for cement concrete (1:2:4) using 12.50 mm graded stone aggregate as in fillings and mass concrete, filling backs of chowkats, hold fasts etc., complete all as specified and directed.(SRW)

M&L For Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.(SRW)

S&F Plates (plain or chequered ) channels,square cut or notched (ordinary and counter sunk ) and forming holes with riveted, bolted or welded attachment complete all as specified and directed.(SRW)

M&L for pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.(SRW)

M&L for pre-painted galvalumealuminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.(SRW)

M&L for Preparing new steel surfaces and applying two coats of synthetic enamal paint over one coat of red oxide primer complete all as specified and directed.(SRW)

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.(SRW)

S&F anodised aluminium snap grid frame work (size of grid 605x605mm) for false ceiling all as specified including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.l. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.(SRW)

M&L 12 to 12.50mm thick semi-perforated/pin holed particle board/tiles, 600x600 ± 5 mm in size fixed in false ceiling as per manufacturer's instructions to existing frame work or on snap grid as in repairs complete all as specified and directed.(SRW)

S&F WPC/PVC Wall panelling of fluted/louvers/hollow sections/ (colour/pattern as approved by AO) complete fixed in position in all respect including supply and fixing of all accessories like fasteners/ screws/solvent/ fillets etc all as recommended by manufacturer and complete all as specified and directed. Note: WPC/fluted/louvers panelling will be minimum 25% of total panelling area (SRW)

Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good to disturbed surfaces complete incl ventilators including reqd shape for hold fast block for new frame complete all as specified and directed.(SRW)

Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and directed.(SRW)

S&F door frames made of PPGI sheet of 1.20 mm thickness for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, hold fast etc., complete all as specified, size 105 x 60mm and incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and directed.(SRW)

S&F factory made flush shutters 30mm thick minimum 5 ply, solid core construction, with block board core and plywood face panels, commercial type on both sides with 6mm thick lipping frame to match complete all as specified and directed.(SRW)

M&L for Preparing new wooden surfaces and applying two coats of synthetic enamal paint over one coat of pink wood primer complete all as specified and directed.(SRW)

M&L for Preparing old steel surfaces and applying two coats of synthetic enamal paint over one coat of red oxide primer complete all as specified and directed.(SRW)

S&F steel windows 1.25 mm thick Box type (primer coated) ERW hollow ‘P’ section of size 60mmx25mm single rebated comprises of glazed and skeleton shutter EWR Sec 50mmx20mm and 1mm thick and two openable leaf consisting two Nos sash bar of ‘T’ section 20mm x 3mm complete welded to frame with one vertical mullion of EWR box ‘T’ section of size 60mmx25mm and 1.25mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B1 for four nos for each window including S&F following fittings welded to each window :- (a) Holdfasts 150mm long 12mm x 3mm made to shape – 04 Nos per window (b) Handle of Z Sec 20mmx25mm, 100mm long – 1 Nos of leaf, (c) MS tower bolt 150mm long - 02 Nos per leaf (d) ‘Z’ sec 20mm x 25mm, 100 long stopper – 01 Nos per leaf, (e) Cleat 55 mm long of hollow square 15mmx20mmx63mm welded to hinges – 01 Nos per leaf (f) MS pintal hinges of size 75mmx12mm – 02 Nos per leaf (g) Fabrication and fixing arrangement complete. (h) Clear Glass 4 mm thick (j) Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm (k) Grill of 8mm sq. bar of length equal to the width of window @ 100mm c/c with cut space to accomodate the handle where directed/applicable.(SRW)

S&F stainless steel finished 202 Grade butt hinges 100mm long complete all as specified and directed.(SRW)

S&F stainless steel finished 202 Grade butt hinges 150mm long complete all as specified and directed.(SRW)

S&F stainless steel 202 Grade finished 200mm long tower bolts in square shaped with minimum 10mm dia rod complete all as specified and directed.(SRW)

S&F Stainless Steel 202 Grade Finished curved Handles 200 mm long complete all as specified and directed.(SRW)

S&F Stainless Steel 202 Grade Finished Sliding Door Bolt/Aldrop 16 x 300mm with square nuckle complete all as specified and directed.(SRW)

S&F Aluminium (extruded section) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repairs complete all as specified and directed.(SRW)

S&F 5 mm thick clear toughened glass for glazing works etc fixed with aluminium beads/uPVC windows any size of pane complete all as specified and directed(SRW)

M&L demolition of cement Concrete (unreinforced) of any description and in any position not otherwise specifically all as specified and directed (SRW)

M&L PCC 1:4:8 type D-2 (using 40 mm graded agg.) as in sub base unde floors complete all as specified and directed.(SRW)

M&L for plain cement concrete 1:2:4 type B-0 using 12.5mm graded mechanically crushed stone aggregate as in benching, rounded or chamfered on edges, coving shall be 150 mm in radius complete all as specified and directed.(SRW)

M&L for hardcore of broken stone boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified.(TD=8.4, TE=8.4)

M&L for cement concrete 1:4:8 type D-2 using 40mm graded aggregate as in foundation, filling and mass concrete complete all as specified.(TD=1.3, TE=1.3)

M&L for 75mm thick cement concrete 1:4:8 type C2 using 40mm graded stone aggregate as sub base in floors over well rammed earth complete all as specified.(TD=6.7, TE=6.7)

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings etc removing material for taking credit (credit shall be recovered as per credit Sch attached) and also making good disturbed surfaces of wall, floors etc complete all as specified and directed.(SRW)

M & L for point wiring with 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper conductor for one light/fan and including PVC rigid concealed conduit medium grade 19/20 mm dia to be terminated in pressed steel terminal boxes with top cover plate including 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper earth continuity conductor controlled by one switch and/or one regulator complete including repairing the surfaces in CM 1:3 and finishing the surface as per existing treatment all as specified and directed (Switches and regulators shall be measured and paid for separately.) ( Wiring shall be done as per colour code in IS for phase, neutral and earth) (In case of Modular: Modular cover plate and metal flush boxes incl in Point wiring) Note : i) Eye/bottle thimbles shall be used for connection in switches/sockets & MCB's in DB's without any extra cost. (TD=4, TE=4, SP=2, SRW=50)

All as per Sl item No 125 above herein before but one 5Amp socket point on independent board complete all as specified and directed. (TD=1, TE=1, SP=1, SRW=20)

All as per Sl item No 125 above herein before but one socket out let 5 pins 5 Amp on the same board but with other switches complete all as specified and directed. (TD=1, TE=1, SP=1, SRW=20)

All as per Sl item No 125 above herein before but one socket out let 3 pin 15 Amp Independent with 2.5 sqmm copper conductor (multi-stranded) PVC insulated electric cable 1100 volts (ISI Marked) including 2.5 sqmm PVC insulated and unsheathed FRLSH single core stranded copper as earth continuity conductor complete all as specified and directed. (TD=1, TE=1, SRW=2)

Supply & fix batten fitting with LED batten fitting of 20W, 4 feet long of extruded thermoplastic body with PC diffuser, isolated body environmental friendly energy efficient including neccesary fitting on wall and making electric connection from ceiling rose to connector with suitable size of electric cable and making good the disturbed surface complete all as specified and directed.. (TD=2, TE=3, SP=1, SRW=2)

All as per Item No- 129 above but with LED batten fitting of 10W, 2 feet long complete all as specified and directed.. (TD=1, TE=1, SP=1, SRW=2)

S&F exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louvers, BEE, five star rated including fixing the fan with all connecting accessories and making electric connection from c/rose etc complete all as specified and directed. Note:- Fixing of Exhaust Fan on wall with suitable size anchor bolt, making hole in wall for grouting and making good the disturbed surface including plaster work shall be part of job at no extra cost. (TD=1, TE=1)

M&L for sand cushioning to under ground cables with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable complete all as specified and directed. (TD=3, TE=2, SP=6, SRW=3)

Material and labour for old size brick well burnt, laid flat, for cable protection complete all as specified and directed. (TD=4, TE=250, SP=850, SRW=350)

M&L Earthing complete with galvanised steel earth plate electrode, 600x600 x 6.0mm thick buried directly in ground(earth pit not less than 2.25m deep below normal level) connected to galvanised earth lead wire 4.0mm dia by means of nuts, bolts, & washers of GI as shown in electrical plate No 3 of SSR Part I. Connected to earthing test point testing complete including necessary earth pit chamber PCC 1: 3: 6 type C1, and 50mm thick RCC 1 : 2: 4 chamber cover and with 8mm dia mild steel re-enforcement of 15Cm C/C spacing both ways with a handle made of 8 mm bar for fitting, galvanised iron funnel, wire mash watering pipe GI 20 mm dia light grade, and protection to earth lead shall be provided with GI pipe light grade 15mm dia up to 7.5m from the earth plate electrode, excavation, retuning filling, Removal of surplus soil, charcoal and common salt mixed refilling of soil etc all included complete all as directed. (TD=1, TE=1 SRW=2)

Supply and fixing wall complete and accessories, 230 V, 450 mm sweep. Min air delivery 210 CFM with service value with brushless direct current motor (BLDC) complete all as specified and directed. (SP=1, SRW=20)

M&L in repair for Modular Socket 6A/16A - 2/3 pin combined 2 module type complete all as specified and directed (SRW)

M&L in repair for Modular Socket, 6A - 2/3 pin combined 2 module type complete all as specified and directed (SRW)

M&L in repair for Modular switch 1 way 6A, 1 module type complete all as specified and directed (SRW)

M&L in repair for Modular switch 1 way 16A, 1 module type complete all as specified and directed (SRW)

M&L in repair for Fan step regulator, 120W -AC 230 Volt modular complete all as specified and directed (SRW)

Material and labour in repair for ceiling rose surface type, 65 mm x 50 mm two to three terminals / PVC / polycarbonate, isolated body fixed on PVC block complete all specified and as directed. (SRW)

Supply and fixing in repair for sub main wiring two single core PVC insulated and unsheathed cable with 6.0 Sqmm multi -strand copper conductor drawing in PVC concealed conduit with 6.0 Sqmm PVC copper conductor cable as in earth wire system ,including taking out old wiring complete all as specified and directed (SRW)

Supply & fix in replacement of existing unserviceable Sheet metal enclosure with new DB’s with degree of protection IP 54 suitable for MCBs of single pole and neutral 8 way double door type with 200 amp rated bus bar complete all as specified and directed. Note: i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. ii) The disturbed surface shall be match with existing shall be part of job. (SRW)

Supply and fix in replacement of MCB SP up to 6-32 Amp complete all as specified and directed (SRW)

Supply and fix in replacement of MCB SPN 6-32 Amp complete all as specified and directed. (SRW)

Supply and fix in replacement of Recess mounted LED luminaire with more light distribution and clutter free ceilings of 36 watt suitable for gridd celling Cutout dimensions: 2x2 Model :Immaculate LED Trimless complete all as specified and directed (SRW)

Material and labour in repair for angular type lamp holder, PVC/ polycarbonate type with back plate suitable for 15/18 watts for batten fitting, including plastic square board of required size complete all as specified and directed (SRW)

S&F in repair LED Lamp inverter trype 9 Watt complete all as specified and directed (SRW)

S&F in repair new generation energy saving and environmental friendly long life LED building security light 1x25 watts made up of pressure die cast alluminium housing with high power LED as light source and lense embedded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07, with all accessories including suitable bracket with 32mm bore light grade GI pipe bemd to shape, including MS clamp of size of required size and PVC cable 1.5 Sqmm twincore from ceiling rose to light fittings complete all as specified and directed. (SRW)

Supply and replace environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit led luminaire comprising of high brightness leds of capacity10 Watt complete all as specified and directed. (SRW)

Supply,laying and testing cable XLPE insulated ,screened ,PVCX bedded galvanised steel strip or wire armoured electric cable power cable 1100 volts grade with stranded alminium conductor of size 16 sq mm x 4 core complete all as specified and directed. (SRW)

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for laying of Pipes, cables, poles,Stay and strips etc and getting out in Soft/Loose soil complete all as specified and directed. (SRW)

Returning, filling-in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil complete all as specified and directed (SRW)

Removing excavated material not exceeding 50m and depositing where directed at a level of not exceeding 1.5m above the starting point complete all as specified and directed (SRW)

Material and labour for replacement of GI tubing light grade 40 mm bore for passing through cables under the floor ,along the wall or along the pole complete all as specified and directed. (SRW)

Jawandha Enterprises (BID ID -3456328)

m/s panchmukhi builders (BID ID -3456278)

M/S RAJ KUMAR GUPTA (BID ID -3455760)

Buttar Construction Co. (BID ID -3451901)

DELTA CONSTRUCTION CO (BID ID -3455782)

AR CONSTRUCTIONS (BID ID -3453450)

FAVOURITE ENGINEERS (BID ID -3454838)