ADDITION/ALTERATION AND SPECIAL REPAIRS TO PERIMETER WALL AT NTS (G) UNDER GE AF GURGAON

Amount

Taking down cement plaster of any description on concrete surfaces such as soffit of RCC slab, chajjas and brick walls, Ceiing etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for Rough Cast Plaster on Brick Walls consisting Under Coat of Cement and Sand Mortar 1:3 not less than 10mm thick and while it is still in Plastic state the Rough Cast Mixture consisting of Crushed Stone or Fine Gravel mixed of size 6mm with Coarse Sand and Cement in the ratio 1:1:1 shall be applied and finish Even, complete all as specified and as directed.

M&L for preparing newly Rough Cast plastered surfaces of Walls and applying Two Coats of acrylic Weather Coat Exterior Paint with approved Tint over a coat of Primer (as per Manufacturer's instructions), complete all as specified and as directed.

M&L for Rendering 15mm thick in CM 1:4 on of brick work or concrete surface finish ever and smooth (w/o using extra cement) including WPC as per user manual complete all as specified and as directed. (cost of WPC is deemed to be included in quoted rates of plaster/rendering).

M&L for preparing newly plastered surfaces of Walls and applying Two Coats of acrylic Weather Coat Exterior Paint with approved Tint over a coat of Primer (as per Manufacturer's instructions), complete all as specified and as directed.

Demolition/Dismantling of Brickwork or stone/ boulder masonry, built in cement mortar incl all quoins, arches, pillars, etc,complete all as specified and as directed.

M&L for Brickwork with subclass 'B' bricks (old size bricks), straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as directed.

Excavation in post holes (or similar holes) in Hard /Dense soil each n exe 0.5 cu.m, gettting out, returning, filling in and ramming earth or broken rubble mixed with earth around , in layers not exeeding 25cm, watering, and removing surplus soil to a distance n exe 50 m and making good surface complete all as specified and as directed.

M&L for cement concrete 1:2:4 type, B1 using 20 mm graded stone aggregates as in copings , foundation , including necessary fromwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

M&L for Mild Steel work as in fencing pole, doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete (Fe 410-W (Gde-E-250) quality A) at any position complete all as specified and as directed.

S&F pre-painted galvatume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed.

M&L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or quare nut, exc 5cm long but n exc 10cm long complete all as specified and as directed.

M&L for preparation of new surface of any description and applying two coats of synthetic enamelled paint over a coat of red oxide primer on steel surface over 10cm width or girth complete all as specifed and as directed.

S&F in repair galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts, incl securing or tying at crossing with and provn of galvanised mild steel wire, staples or steel pins, complete all as specified and as directed.

S&F hot dipped galvanised concertina razer coil 730mm dia, string steel high tensile concrete core wire 2.5mm dia having 200-250gm zinc coating , 0.5 mm thick razer sheet having 90-120gm, zinc coating and 19mm width (before wraping centre core wire) with clip 1.6mm thick complete all as spd and as directed.

M&L for preparation of old steel surface of any description and applying one coats of synthetic enamelled paint on steel surface over 10cm width or girth complete all as specifed and as directed.

Chaudhary Constructions

PAWAN KUMAR

M/s Vijay Enterprises

ASHISH AND CO

ANIL KUMAR

M/S Rohit Enterprises

M/s GANJOO AND CO

P R Constructions

M/S ujjwal associates