CA NO GE(H)-28/2024-25 CONSTRUCTION OF 01 LAB UNDER PM SHREE KV SCHOOL IN THE AOR OF AGE B/R-II UNDER GE HISAR AT HISAR MIL STN

Amount

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil.

Excavation in trenches in soft/loose soil n exc 1.50 meter wide and n exc 1.50 meter in depth for foundation of pole, laying cable etc and getting out etc complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers n exc 25 cm thick etc complete all as specified and directed.

Removing excavated surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point etc complete all as specified and directe.

Earth filling under floors including spreading, leveling, watering and well ramming in layers not exc 25 cm thick. Note :- Soil obtained from excavation under item here-in-before shall be used for filling.

M&L anti-termite treatment to the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified & as directed.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete.

M&L formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete all as specified and directed.

M&L formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similar work exc 5cm but n exc 10cm wide for rough finished flat surfaces of concrete all as specified and directed

M&L formwork to flat surfaces of chajjas, chullah hoods, troughs and similar items including edges for rough finished surfaces.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L reinforced cement concrete M-25 grade (Design mix) using 20mm graded stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in columns, pillars, piers, posts, struts and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L reinforced cement concrete M-25 grade (Design mix) using 20mm graded stone aggregate in chajjas and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L reinforced cement concrete M-25 grade (Design mix) using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified

All as per serial item No. 20.00 here-in-before but 6 to 10mm dia in stirrups, spacers and binders

M&L for brick work using old size fly ash bricks as specified in clasue 6 of Particular specification, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

M&L brick work using old size fly ash bricks as specified in clasue 6 of Particular specification, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified

M & L for rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces of walls, finished even and smooth without using extra cement including mixed with and including water proofing compound @3% by weight of cement complete all as specified and directed.

M & L for rendering 10mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

Supply only water proofing compound (ISI marked).

M&L for providing 10mm thick polymer modified plaster in ration 1:10 (1 Part of polymer and 10 parts of cement with solid contents not less than 20%) over slab and applying priming coat of epoxy primer with resin and hardner with water dilution as per manufacturer instructions, applying 1st coat of solvent based polyurathene liquid membrane not less than 500 micron thick UV stable having SRI value greater than equal to 105 with consumption of 0.61 Kg/Sqm and applying 2nd coat solvent based polyurathene liquid mambrane not less than 500 micron thick UV stable having SRI value greater than liquid to 105 with consumption of 0.61 Kg/Sqm over dried 1st coat complete all as specified and directed. Make : Asian Paints / Pidilite / STP.

M&L for 75mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for 75mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for vitrified ceramic tiles (wooden pattern) 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles (Wooden Pattern) , 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for glazed ceramic (coloured) 1st quality, 350mm x 250mm x 7 / 450mm x 350mm x 7mm thick, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for machine cut Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 15mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified. Note : - Kota stone shall be of size 550mm x 550mm (minimum) when brought at site.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete with glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, and including taking down old U/S steel window complete. DRG NO. CEJZ/TD-2013/01 sheet (1/3, 2/3, 3/3) Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze/ guard bar shall be measured and paid separately.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks, cooler stand and similar work including welding conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm (Single rebated) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made, 30 mm thick flush shutter (solid core construction with block board core and plywood faces panel commercial type on both side etc complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) including shutters with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc, Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws including powder coated 'D' type handle of suitable size, tower bolt of suitable size, suitable size hinges heavy grade complete all as specified & as directed. Note :- Mortice lock, Door closer & Glass panes / ACP sheet shall be measured & paid seperately under relevant item of BoQ.

Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified.

Supply and fixing 5.5mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified.

Material and labour preparation of newly plastered/asbestos cement surfaces of ceilings & applying three coats of white wash complete all as specified.

Material and labour preparation of new plastered surfaces and applying two coats of oil bound distemper of approved shade/tint over a coat of primer on walls including 2mm thick wall care putty all as specified & directed

M&L for preparing new plastered or unplastered surface of walls with 2mm thick wall care putty over plastered surfaces and applying two coats of exterior emulsion paint Apex (Weather proof) of approved shade/tint over a coat of primer of same make on walls all as specified & as directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified and directed.

M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall.

S&F 20mm bore stainless steel powder coated curtain rod with 02 Nos decorative ball type brackets (for each opening) and 02 Nos decorative side stoppers (for each opening) fixed on wall with wooden gutties & screws complete all as specified & as directed.

S&F butt hinges 100mm size of Harrison SS 0861 economy series polished and fixed type B-11 complete all as specified and directed

S&F Harrison 0888 economy Tower bolt, finish Matt/ SS size 150mm and fixed complete all as specified.

S&F Harrison D type 0744 PK 6 stainless cabinet handle of size 150mm complete all as specified.

S&F maharaja Floor door stopper of brass body and tongue, , fixed in floor, overall length of cover plate 140mm complete all as specified.

Supply and fixing 250 mm long brass sliding door bolts with hasp & staple (bolt type) and fixing clips of sheet, and fixing bolts and sliding bolts of brass bolts complete all as specified.

M&L for 20mm thick granite (of any type) work table rubbed and polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc laid over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified & as directed.

M&L for Rounding to edges of stone slabs one edge,such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

S&F towel rail, brass chromium plated, 20mm dia, ‘D’ type, 45cm long between flanges.

S&F CP soap dish complete all as specified and directed.

S&F 15 mm bore long body bib cock, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule confirming to cat No. 8108 of prayag series or techno.

S&F cast iron floor trap of 75 mm bore, with grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4), complete all as specified & as directed.

S&F salt glazed stone ware gully trap square or round mouthed type 'P' of size 150 x 150 mm with CI grating, setting & jointing with cement with grouting surrounding gully trap with PCC 1:3:6, type C-0 block 30x30x45cm together with necessary form work, excavation & earth work in soft/loose soil, complete, all as specified and as directed.

S&F Grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40 gms) all as directed.

S&F 32/38/40 mm dia PVC flexible waste pipe with socket for union, for WHB/urinal/sink complete all as specified.

S&F CPVC pipes (outer dia of pipe 16mm) SDR 11 & Plain CPVC SDR 11 fittings laid on wall / ceiling or laying in floor complete all as specified with all fittings / connections and making good to required surfaces by using white cement / masonry works complete all as specified and directed. Note :- Rates quoted shall deemed to be included for making hole / nitch for replacement of pipe and making good distrubed surfaces to match with existing surface and finish all as directed.

S&F of CPVC pipes (outer dia of pipe 20mm) SDR 11 & Plain CPVC SDR 11 fittings laid on wall / ceiling or laying in floor complete all as specified with all fittings / connections & MS clamps / clips and necessary screwing as required complete and fixed with or without concealed to walls, and making good to required surfaces by using white cement / masonry works complete all as specified and directed. Notes :- (i) The quoted rates includes all plain CPVC fittings and pipe cutting fixing with CPVC solvent cement and testing.

Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks (colour other than black as approved by Engineer-in-charge) triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and as directed.

S&F cupboards/wardrobes, factory made, frame shall be of 1.25mm thick pressed steel with PBI sheet of size 90x70mm, shutter shall made out of 1mm thick pressed steel with 06 Nos 100mm long 3.15mm thick steel hinges, standard pattern rim lock with complete locking arrangement including 12mm vertical rod shall be provided (brass mortice lock, vertical type, size 65mm, 2 levers, ISI marked with escutcheon plate and two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with minimum 6 Nos 12mm dia mild steel bolt 150 mm long grouted in brick wall/concrete including making good the disturbed surfaces as original with CM (1:4) or PCC (1:2:4) type B0 complete all as specified and as directed. Note :- The measurement shall be taken of front elevation and not girthwise.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid under floors complete all as specified.

M&L for factory made hard wearing coloured ceramic tiles 300x300x10mm in size or nearest higher size laid as in floor etc, set and jointed in neat cment slurry & pointing in white or colured cement to match with the shade of tiles over & including 20mm thick screed bed in cement & sand mortar 1:6, complete, all as specified & as directed. Make :- VC shield series of Somany or equivalent of make mentoned in Appx 'C' here-in-after

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. complete, all as directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm bot not exc 10cm long and dia of neck not less than 10mm complete all as specified.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ ISI marked (IS-2062) all as specified and as directed.

S&F fibre glass reinforced translucent corrugated sheeting of 2mm thick with two corrugation side lap fixed with coach screws or 'L' type are cranked hook bolts in lieu of screw as specified all as directed.

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including concealed PVC rigid non metallic conduit 20mm dia medium grade (ISI marked) with all fittings such as tees, bends etc including sunk type pressed steel box covered with and including 3 mm thick new bakelite laminated sheet top cover ‘Hylam’, complete, all as specified & directed. (Note :- Switches, sockets etc shall be measured and paid for separately under appropriate items of BoQ' ).'

All as per item No 73.00 (here-in-before) but ceiling fan /exhaust fan point controlled by one Number one way switch.

All as per item No. 73.00 (here-in-before) but for one 5 Amp socket outlet on independent board controlled by one Number one way switch on independent board

All as per item No. 73.00 (here-in-before) but for one 5 Amp socket outlet on the same board controlled by one Number one way switch on same board.

All as per srl item No. 73.00 (here-in-before) but for 15 Amp socket out let by using 2.50 Sqmm PVC insulated unsheathed copper conductor cable FRLS multi stranded on independent board including provn of 2.50 Sqmm unsheathed, multistranded copper conductor cable FRLS continues as earth wire connected to earth dolly etc complete all as specified and directed by Engineer-in-Charge.

S&F switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts all as specified & directed.

S&F switch piano flush type, single pole, one way, 15 Amp, 230 Volts.all as specified & directed.

S&F flush type socket outlet multipurpose 3 Pin 5/6 Amp (with 2 pin outlet also) 230 volts AC complete all as specified and directed.

S&F flush type socket outlet multipurpose 3 Pin 15/16 Amp (with 3 pin 5/6 Amp outlet also) 230 volts AC complete all as specified and directed.

S&F lamp holder, insluated body, with back plate suitable for batten fittings & complete all as specified & directed.

S&F ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed.

S&F Ceiling fan regulator electronic step type of suitable wattage, 230V suitable for 1200/1400 mm ceiling fan etc complete all as specified and directed.

S&F sheet metal enclosure distribution board SP&N, 8 way, double door, powder coated, protection class IP-42, suitable for mounting MCB, DBs confirming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating copper bus bar, complete all as specified & directed.

S & F MCB SP, 6 to 32 Amps 240 Volts , 'C' curve, 10 KA, IS-8828 marked for fixing in DB complete all as specified & directed. . Note :-Make of MCB shall be same of that DB.

S&F MCB SPN, 40 to 63 Amps 240 Volts , type 'C' curve, 10 KA, IS-8828 marked fixing in DB complete all as specified & directed. Note :-Make of MCB shall be same of that DB..

Supply and fixing LED luminaire 600mm x 600mm, 35/36 watt, any type (ie warm white, cool day light) & 220 V AC surface mounted type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed

S&F in replacement of street light LED light fitting 35 Watt, new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover with IP66 protection and impact resistance of IK07 connected with and including 0.5 sqmm flexible copper multistranded conductor cable including fixed on wall / pole all as specified and directed.

Supply and fixing ceiling fans (Copper widing) complete with blades, down rod and accessories, 230V, 1200mm sweep, min air delivery 210 CFM, BEE five star rated with brushless direct current motor (BLDC) with remote complete all as specified and directed.

Supply & fixing and testing exhaust fan of 300mm sweep heavy duty, double ball bearing, 1400 RPM, suitable for SP 230 / 250 volt, 50 Hz AC supply complete with louver shutter including fixing / grouting of frame in wall & cutting opening complete with covers & connecting with & including 3 Nos 1.5 sqmm single core, PVC insulated but unsheathed FRLS 1100 volts grade cable with multi-stranded copper conductor from ceiling rose to fan complete.

Supply , laying , jointing, testing and commissioning of 16 sqmm 2 core LT underground cable , 1100 volts grade, XLPE insulated and PVC sheathed, armoured heavy duty with multistrand aluminium conductors confirming to IS-7098, laid in trenches /fixed on wall /floor /road /culverts /pole or encased in GI pipe complete all as specified. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

M&L for brick covering to underground electric cable using sub class ‘B’ bricks, laid dry, flat, perpendicular to the direction of cable etc complete all as specified and directed.

M&L for Sand cushioning 230mm thickness with dry sand (one layer of 80mm thickness before laying of cable and other layer of 150mm thickness after laying of cable) and punned down to 180mm after laying of cable in trenches for protection of cable complete all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

Supply, and laying 3 layer PP-R polyproplene rendon copolymer, concealed pipes SDR 7.4 (PN-16) stablized and antimicrobial fusion welded having thermal stability for hot and cold water supply including all PP-R plain and brassed threaded polypropylene random fitting fixed to in trenches / walls / celling paying in floors etc to complete of size outer dia 32 mm all as specified and directed.

Supply and fixing PP-R gate valve brass inset connect to PP-R pipe 32 mm bore complete all as specified

Cutting the existing DI/CI pipe line of size 80/150 mm dia for addition / aleration and screwing existing steel tubing after alteration including necessary fitting suchs union, bends, tee, reducer, niples, sockets etc and connecting branch connection complete all as specified and as directed

Balaji Construction Co. (BID ID -3121920)

M/S KAVITA CONSTRUCTION (BID ID -3108775)

SHRI HARI BUILDERS (BID ID -3122416)

malik constructions (BID ID -3106008)

M/S RAJESH KUMAR & SONS (BID ID -3108746)