8775 PERIODICAL MAINT SERVICING OF DG SETS STREET LIGHTS FLOOD LIGHTS HIGHMAST AND OTHER MISC WORKS AT CHSC UOT CHSC 4 RMC QTRS ALC QTRS CH COMPLEX AREA AND OTHER CONNECTED AREA UNDER AGE EM II OF GE (SOUTH) PUNE

Amount

M&L for maintanence and servicing of 160 KVA Diesel genarator sets installed at Upper OT: 02 Nos, Lower OT: 01 No, Skin ward: 01 No Make : Greaves & Stamford (03 Nos) & Crompton Greaves (01 No) including connected Alternator and carryng out routine 'A' check (every 50hrs/1 month wichever is earlier) of the engine and servicing works as listed below for smooth functioning all as per manufactures instructions and as directed. (a) To check (every 50hrs of working DG set/ 1 month wichever is earlier. (i) Lubrication greasing to all parts (ii) Check engine oil level (quality and any top up required if any to be informed to concerned JE E/M and AGE E/M) (b) Fuel system : Drain sediment from fuel tanks. (c) Air System: (i) Clean pre Cleaner dustpan weekly (ii) Check Air cleaner restriction clean/change cleaner element if required. (d) Cooling System: Check coolant level (top up if required) (e) Other Maintenance: (i) Check and correct leaks (ii) Drain fuel filter.water separator. (iii) Check belts & adjust if required. Note:(i) Engine oil/ Radiator coolent / spare parts required if any will be measured and paid separately, however materials like grease, lubricating oil, gasket, oil seal, washer nuts, bolts etc. shall deemed to be included in the quoted rate. (ii) Checks carried out for each DG set will be measured as one job.

All as per item No.1 here in before but 125 KVA DG Set of Make: Kirloskar (01 No) and Crompton Greaves (01 Nos) installed at Lower OT and Gamma Center,complete all as directed by Engr-in-Charge.

All as per item No.1 here in before but 100 KVA DG set make Greaves installed at Lower OT CHSC ,complete all as directed by Engr-in-Charge.

All as per item No.1 here in before but 82.5 KVA DG Set, Model Cummins installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.1 here in before but 63 KVA DG set make Kirloskar installed at Lower OT CHSC,complete all as directed by Engr-in-Charge.

All as per item No.1 here in before but 40 KVA DG set Make Kirloskar (01 Nos) and Greaves & Stamford (01 nos) installed at College of nursing & Skin ward,complete all as directed by Engr-in-Charge.

M&L for carring out following periodical maintanence on 160 KVA Diesel genarator sets installed at Upper OT: 02 Nos, Lower OT: 01 No, Skin ward: 01 No of Make : Greaves & Stamford (03 Nos) & Crompton Greaves (01 No) including connected Alternator and carryng out routine 'B' check (every 250hrs/06 month wichever is earlier) of the engine and servicing works as listed below for smooth functioning all as per manufactures instructions and as directed. (a) To check (every 250 Hrs/Every 6 month) (i) Repeat all 'A' check activities (Lubrication and greasing) (ii) Drain engine oil sump thoroughly and refill with new engine oil up to marked level. (iii) Renew oil filter element, clean carbon separator (iv) Record engine oil pressure (with load and without load). (b) Fuel system : (i) Check Hydraulic Governor oil. (ii) Check throttle linkage.(iii) Lubricant Ball joints of the throttle linkage of Hydraulic Governor. (iv) Change of Fuel filter elemnt (v) Clean fuel tank breather.. (c) Air System: (i) Clean / Change cranckcase Breather. (ii) Check Air Pipings/durettes (iii) Change air filter element (d) Cooling System: (i) Check coolant in radiator. (ii) Add coolant concentrate if required (for maintaining PH value in between 7.5 to10.5) (iii) Check heat exchanger zinc (sacrificial Anode) plugs. Note: (i) Coolant oil, Engine oil utilised and any measure spare parts if utilized will be measured and paid separatly. (ii) The rate quoted shall deemed to be inclusive of the necessary oil filter, fuel filter , air filter units and the gaskets, O rings and clips required for changing of the filter elements (iii) Checks carried out for each DG set will be measured as one job.

All as per item No.07 here in before but 125 KVA DG Set of Make: Kirloskar (01 No) and Crompton Greaves (01 Nos) installed at Lower OT and Gamma Center,complete all as directed by Engr-in-Charge.

All as per item No.07 here in before but 100 KVA DG set make Greaves installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.07 here in before but 82.5 KVA DG Set, Model Cummins installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.07 here in before but 63 KVA DG set make Kirloskar installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.07 here in before but 40 KVA DG set Make Kirloskar (01 Nos) and Greaves & Stamford (01 nos) installed at College of nursing & Skin ward, complete all as directed by Engr-in-Charge.

All as per item No.12 here in before but 125 KVA DG Set of Make: Kirloskar (01 No) and Crompton Greaves (01 Nos) installed at Lower OT and Gamma Center, complete all as directed by Engr-in-Charge.

All as per item No.12 here in before but 100 KVA DG set make Greaves installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.12 here in before but 82.5 KVA DG Set, Model Cummins installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.12 here in before but 63 KVA DG set make Kirloskar installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.12 here in before but 40 KVA DG set Make Kirloskar (01 Nos) and Greaves & Stamford (01 nos) installed at College of nursing & Skin ward, complete all as directed by Engr-in-Charge.

M&L for servicing of Self Starter assembly after disconnecting from engine and dismantling the bendix pinion and spring, connector assembly, carbon brushes etc. cleaning all accessories thoroughly, replace the wornout parts like brushes, bushes, , contact plates, jumping leads and seals, revarnishing the field coil and armature if required and reassembling the same, refitting it to the engine and testing complete all as directed for 160 KVA Diesel genarator sets installed at Upper OT: 02 Nos, Lower OT: 01 No, Skin ward: 01 No. Make : Greaves & Stamford (03 Nos) & Crompton Greaves (01 No).

All as per item No.19 here in before but 125 KVA DG Set of Make: Kirloskar (01 No) and Crompton Greaves (01 Nos) installed at Lower OT and Gamma Center, complete all as directed by Engr-in-Charge.

All as per item No.19 here in before but 100 KVA DG set make Greaves installed at Lower OT CHSC,complete all as directed by Engr-in-Charge.

All as per item No.19 here in before but 82.5 KVA DG Set, Model Cummins installed at Lower OT CHSC,complete all as directed by Engr-in-Charge.

All as per item No.19 here in before but 63 KVA DG set make Kirloskar installed at Lower OT CHSC,complete all as directed by Engr-in-Charge.

All as per item No.19 here in before but 40 KVA DG set Make Kirloskar (01 Nos) and Greaves & Stamford (01 nos) installed at College of nursing & Skin ward, complete all as directed by Engr-in-Charge.

M & L for repair and servicing of PT pump assembly and injectors by replacing the unserviceable parts like centre shaft, loading spring, relief valve-2 Nos bearings.governor barrels & plunger-1Set O-ring kits,gasket kit,injector plunger & barrel -6Nos,ball check -6Nos and calibration and phasing of FIP in test bench and spray test, leakage test etc. for injectors and reassembling them to the engine and testing after completion complete all as directed for 160 KVA Diesel genarator sets installed at Upper OT: 02 Nos, Lower OT: 01 No, Skin ward: 01 No Make : Greaves & Stamford (03 Nos) & Crompton Greaves (01 No) Note: The rate quoted deemed to be inclusive of transportation of FIP and injectors to workshop/test bench and minor spares required such as centre shaft, loading spring, relief valve-2 Nos bearings.governor barrels & plunger-1Set O-ring kits,gasket kit,injector plunger & barrel -6Nos,ball check -6Nos etc. however injector sleeves if required to be replaced shall be measured and paid in relevant items.

All as per item No.25 here in before but 125 KVA DG Set of Make: Kirloskar (01 No) and Crompton Greaves (01 Nos) installed at Lower OT and Gamma Center, complete all as directed by Engr-in-Charge.

All as per item No.25 here in before but 100 KVA DG set make Greaves installed at Lower OT CHSC,complete all as directed by Engr-in-Charge.

All as per item No.25 here in before but 82.5 KVA DG Set, Model Cummins installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.25 here in before but 63 KVA DG set make Kirloskar installed at Lower OT CHSC,complete all as directed by Engr-in-Charge.

All as per item No.25 here in before but 40 KVA DG set Make Kirloskar (01 Nos) and Greaves & Stamford (01 nos) installed at College of nursing & Skin ward, complete all as directed by Engr-in-Charge.

M & L for sevicing and calibration of governor unit in-si-tu including replacement of worn out parts if any and testing it for minimal hunting and a maximum droop of 20% complete all as specified and as directed for 160 KVA Diesel genarator sets installed at Upper OT: 02 Nos, Lower OT: 01 No, Skin ward: 01 No Make : Greaves & Stamford (03 Nos) & Crompton Greaves (01 No) Note: The rate quoted deemed to be inclusive of minor spares required such as O rings, washers, gaskets, nuts bolts etc. however solenoid switch if required to be replaced shall be measured and paid in relevant items.

All as per item No.31 here in before but 125 KVA DG Set of Make: Kirloskar (01 No) and Crompton Greaves (01 Nos) installed at Lower OT and Gamma Center, complete all as directed by Engr-in-Charge.

All as per item No.31 here in before but 100 KVA DG set make Greaves installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.31 here in before but 82.5 KVA DG Set, Model Cummins installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.31 here in before but 63 KVA DG set make Kirloskar installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.31 here in before but 40 KVA DG set Make Kirloskar (01 Nos) and Greaves & Stamford (01 nos) installed at College of nursing & Skin ward, complete all as directed by Engr-in-Charge.

M & L for Overhauling of radiator assy by disconnecting and removing from eingine , dismantling the top & bottom chambers , descalling the sediments and scales , corrosion ..etc by means of acid cleanig and high pressure water washing , air cleaning , re assembling the same with new gaskets, including arresting the leakage if any by soldering/ brazing or cold repairing as required, and refixing to the engine with new hoses ,clips as required complete all as directed for 160 KVA Diesel genarator sets installed at Upper OT: 02 Nos, Lower OT: 01 No, Skin ward: 01 No.Make : Greaves & Stamford (03 Nos) & Crompton Greaves (01 No) Note: The rate quoted deemed to be inclusive of minor spares required such as O rings, Jublee clips, washers, gaskets, nuts bolts etc. and transportation of the radiator assembly to workshop if required.

All as per item No.37 here in before but 125 KVA DG Set of Make: Kirloskar (01 No) and Crompton Greaves (01 Nos) installed at Lower OT and Gamma Center, complete all as directed by Engr-in-Charge.

All as per item No.37 here in before but 100 KVA DG set make Greaves installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.37 here in before but 82.5 KVA DG Set, Model Cummins installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.37 here in before but 63 KVA DG set make Kirloskar installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.37 here in before but 40 KVA DG set Make Kirloskar (01 Nos) and Greaves & Stamford (01 nos) installed at College of nursing & Skin ward, complete all as directed by Engr-in-Charge.

M & L for draining out from the fuel tank of DG set of capacity 160 KVA and keeping it in a separate container, cleaning the fuel tank all lnternally & externally by removing all the accumulated sediments, leak testing the tank and repair the same if any exists by welding/brazing/cold repairing and painting thereafter with one coat of black synthetic enameled paint over a coat of red oxide and refixing the tank to its original position & refilling the fuel back into the tank including writing of SM/MES No. & date of cleaning of fuel tank complete all as directed.

All as per item No.43 here in before but 125 KVA DG Set of Make: Kirloskar (01 No) and Crompton Greaves (01 Nos) installed at Lower OT and Gamma Center, complete all as directed by Engr-in-Charge.

All as per item No.43 here in before but 100 KVA DG set make Greaves installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.43 here in before but 82.5 KVA DG Set, Model Cummins installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.43 here in before but 63 KVA DG set make Kirloskar installed at Lower OT CHSC, complete all as directed by Engr-in-Charge.

All as per item No.43 here in before but 40 KVA DG set Make Kirloskar (01 Nos) and Greaves & Stamford (01 nos) installed at College of nursing & Skin ward , complete all as directed by Engr-in-Charge.

Supply only fan belts as per exisiting make for DG Sets of capacity 160 KVA, complete all as directed by Engr-in-Charge.

Supply only fan belts as per exisiting make for DG Sets of capacity 125 KVA, complete all as directed by Engr-in-Charge.

Supply only fan belts as per exisiting make for DG Sets of capacity 100 KVA, complete all as directed by Engr-in-Charge.

Supply only fan belts as per exisiting make for DG Sets of capacity 82.5 KVA, complete all as directed by Engr-in-Charge.

Supply only fan belts as per exisiting make for DG Sets of capacity 63 KVA, complete all as directed by Engr-in-Charge.

Supply only fan belts as per exisiting make for DG Sets of capacity 40 KVA, complete all as directed by Engr-in-Charge.

Supply only engine oil of grade SAE 15 W 40/ Servo RR 40 in standard packings / sealed container [CH grade synthetic/semi synthetic) [Make : VOLVOLINE/Servo/ Castrol ],complete all as directed by Engr-in-Charge.

Supply only coolant in standard packings / sealed container. (Servo/Castrol/Volvoline), complete all as directed by Engr-in-Charge.

Supply only Solenoid switch, 24 Volts, Suitable for 160 KVA DG SET ( Make : Lucas / Bosch), complete all as directed by Engr-in-Charge.

Supply only Solenoid switch, 24 Volts, Suitable for 125 KVA DG SET( Make : Lucas / Bosch), complete all as directed by Engr-in-Charge.

Supply only Solenoid switch, 24 Volts, Suitable for 100 KVA DG SET( Make : Lucas / Bosch), complete all as directed by Engr-in-Charge.

Supply only Solenoid switch, 24 Volts, Suitable for 40 to 82.5 KVA DG SET( Make : Lucas / Bosch), complete all as directed by Engr-in-Charge.

Supply only Engine control Unit [ IN-NT-PLUS] 24 Volts, Suitable for 160 KVA DG SET, complete all as directed by Engr-in-Charge.

Supply only Engine control Unit [ IN-NT-PLUS] 24 Volts, Suitable for 125/100 KVA DG SET, complete all as directed by Engr-in-Charge.

Supply only Engine control Unit [ IN-NT-PLUS] 24 Volts, Suitable for 40 to 82.5 KVA DG SET, complete all as directed by Engr-in-Charge.

Supply only Tacho drive meter including cable assembly 1.5 mtr length [0.200]RPM [Make : KOEL/VDO], complete all as directed by Engr-in-Charge.

Supply only power contactors of AC1 300 Amps 3 Pole 415 volts Make L&T/TC/Legrand/ABB, complete all as directed by Engr-in-Charge.

Supply only power contactors of AC1 225 Amps 3 Pole 415 volts Make L&T/TC/Legrand/ABB, complete all as directed by Engr-in-Charge.

Supply only power contactors of AC1 185 Amps 3 Pole 415 volts Make L&T/TC/Legrand/ABB, complete all as directed by Engr-in-Charge.

Supply only power contactors of AC3 100 Amps 3 Pole 415 volts Make L&T/TC/Legrand/ABB, complete all as directed by Engr-in-Charge.

Supply only power contactors of AC3 65 Amps 4 Pole 415 volts Make L&T/TC/Legrand/ABB, complete all as directed by Engr-in-Charge.

Supply only analog type electronic interval timer suitable for AMF panels of DG set with rated votage range 24 V AC to 240 V AC ± 10 % frequency 50 Hz, Din rail mounting and LED indication for timing in progress complete all as directed. Make: Siemens, L & T, Schneider, Legrand, ABB, complete all as directed by Engr-in-Charge.

Supply only automatic voltage regulator (AVR) solid state electronic module with output voltage 415 V, suitable for 40 to 160 KVA DG sets complete all as directed. Make : Stamford, Greaves, Kirloskar

Supply only Indicator lamp, LED type of colour red, blue and yellow complete all as directed by Engr-in-Charge..

Supply only Push botton (start/stop) in red/green colour, complete all as directed by Engr-in-Charge.

Supply only Toggle switch ON/OFF 2 position IP 65 rating, complete all as directed by Engr-in-Charge.

Supply only MCCB 4 Pole 250 amps, 36 KA breaking capacity with adjustable thermal and adjustable magnetic overload protection with Ics=100% of Icu complete all as specified and directed. Make Havells/C&S/Legrand/L&T/Indoasian

Supply only MCCB 4 Pole 200 amps, 25 KA breaking capacity with adjustable thermal and adjustable magnetic overload protection with Ics=100% of Icu complete all as specified and directed. Make Havells/C&S/Legrand/L&T/Indoasian

Supply only MCCB 4 pole 100 amps, 16 KA breaking capacity with fixed thermal and magnetic overload protection complete all as specified and directed. Make Havells/C&S/Legrand/L&T/Indoasian

Supply only MCCB 4P 63 amps, 16 KA breaking capacity with fixed thermal and magnetic overload protection complete all as specified and directed. Make Havells/C&S/Legrand/L&T/Indoasian

Supply only off load change over switch 4 pole of capacity 200 Amps in sheet steel enclosure rated voltage 415 V AC 50 Hz including connecting up the cables with suitable lugs complete all as specified and as directed. Make INDOASIAN Cat part no OCFP0200 or euivalent in L&T, Havells, C & S etc.

Supply only 200 amps current rating On load change over switch four pole with manual changeover open execution complete all as directed. Make: Havells/C&S/Legrand/L&T/Indoasian

Supply only 160 amps current rating On load change over switch four pole with manual changeover open execution complete all as directed. Make:Havells/C&S/Legrand/L&T/Indoasian

Supply and fix in repair Brass, Battery terminals including taking down the old one and greasing with silicone graese after fixing complete all as directed.

Supply and fix in repair moulded PVC body low maintanence lead acid battery 12 volts 180 AH including taking down the old unserviceable complete all as directed. Make: Exide/standard Furukawa/AMCO/Amaron.

Supply and fix in repair moulded PVC body low maintanence lead acid battery 12 volts 120 AH including taking down the old unserviceable complete all as directed. Make: Exide/standard Furukawa/AMCO/Amaron.

Supply and fix in repair display unit (LCD) in the control panel of 100/125/160 KVA DG set including removing the unserviceable display unit from the control panel and connecting with the necessary wiring with soldering and testing after fixing complete all as specified and as directed.

S & F in repair self starter suitable for 24 Volt DC operation Make - Lucas including disconnecting and taking down the existing unserviceable self starter complete all as directed.

Supply and fix in rpair residential type silencer suitable for 160/125/100/82.5 KVA DG set as per CPCP specification after removing damaged industrial type silencer including cutting , welding through proprer tools and plants , including necessary brackets/clamps for support complete all as directed by Engr-in-Charge..

Supply and fix in repair 4" dia 'B' Class M.S Pipe for vertical extension for exhaust piping, with all accessories such as bends, coupling, gaskets, nuts, bolts, washers including supporting brackets and removing the rusted exhaust pipe by cutting/welding complete all as directed by Engr-in-Charge.

M & L for Providing aluminium cladding to the exhaust pipe and silencer of the DG sets by engaging highly skilled technicians after removing the damaged insulation of asbestos rope ( wherever available) and preparing the surface , and providing with 50 mm thick high quality glass wool thermal insulator packing and binding tightly with chicken wiremesh of approved quality to the exhaust pipe upto 4" dia and neatly finishing sealing with 24 SWG aluminium sheet complete all as directed by Engr In Charge.

M&L for painting of DG Set Canopy with two coats of powder coated paint as per existing colour by scrapping the old surface of canopy and applying one coat of red oxide primer and making good complete all as directed by Engr-in-Charge.

M&L for painting of DG Set Exhaust pipe with two coats of heat resistant aluminium paint after necessary surface preparation complete all as spceified as directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6.3 mm thick buried directly in ground vertically to a depth not less than 2.25mtr deep below ground level with top edge of the earth plate not less than 1.5mtr deep below normal ground level, connected with & including galvanised iron strip 32 x 6 mm connected to main test point as directed as earthing lead by means of nuts, bolts and washers of galvanised iron protected by 40 mm dia (medium grade) including concrete pit in PCC (1:3:6) type C-1, RCC cover slab 55 cm x 55 cm x 5 cm with reinforcement of 8 mm dia bar 100 mm c/c bothways including one handle made of 12 mm dia MS bar embedded in pre cast slab and 20 mm bore galvanised iron pipe"medium grade" for watering with GI funnel and wire mess including charcoal and salt in alternate layers of 15 cm including necessary excavation and earth work in any type of soil complete all as specified and as directed and testing on completion.Note:upto 7.5 mtr GI strip and Pipe included in quoted rate.

M&L 32x6mm galvanised iron strip Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required at site all as specified and sirected by Engr-in -charge.

Supply and laying in repair XLPE insulated, armoured, heavy duty electric UG cables with aluminium conductor 1100 volts grade complete including providing lugs as required as specified and directed for cross-sectional area 120 sqmm 3.5 core, complete all as directed by Engr-in-Charge.

All as per item No 99 here in before but of size 95 sqmm, 3 1/2 core, complete all as directed by Engr-in-Charge.

All as per item No 99 here in before but of size 70 sqmm, 3 1/2 core, complete all as directed by Engr-in-Charge.

All as per item No 99 here in before but of size 35 sqmm, 3 1/2 core, complete all as directed by Engr-in-Charge.

All as per item No 99 here in before but of size 16 sqmm, 4 core, complete all as directed by Engr-in-Charge.

All as per item No 99 here in before but of size 10 sqmm, 4 core, complete all as directed by Engr-in-Charge.

All as per item No 99 here in before but of size 10 sqmm, 2 core, complete all as directed by Engr-in-Charge.

All as per item No 99 here in before but of size 06 sqmm, 2 core, complete all as directed by Engr-in-Charge.

Supply, jointing and testing in repair cable jointing kit for 1.1 KV grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 25-50 Sqmm complete all as specified and directed.

Supply, jointing and testing in repair cable jointing kit for 1.1 KV grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 70-150 Sqmm complete all as specified and directed.

Supply, jointing and testing in repair cable jointing kit for 1.1 KV grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 25-50 Sqmm complete all as specified and directed.

Supply, jointing and testing in repair cable jointing kit for 1.1 KV grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 70-150 Sqmm complete all as specified and directed.

Excavating in trenches n. exc 1.5m wide and not e. 1.5m in depth for foundation of poles, laying UG cables, etc and getting out in soft/loose soil complete as specified and directed.

Removing excavated material not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point in soft / loose soil complete as specified and directed.

Returning filling including spreading levelling, watering and well ramming in layers not exceeding 25cm in soft/loose soil complete all as directed by Engr-in-Charge.

M&L for boring/drilling by machines/manual horizontally under the road in any type of soil without cuttiing/disturbing the existing road and inserting GI pipe of any size for drawing the cable through complete all as specified.(GI pipe shall be measured and paid seperately.

M&L for laying double wall corrugated HDPE pipe, UV stabilized of size 120X103 mm (ODX ID), IS-16205 for cable protection laid in trenches or fixed to walls complete all as specified and as directed.

M & L for repairing t of LED street light of any make, type and capacity by replacing unserviceable parts including replacement of damaged connecting wires as per existing size of conductor and taking down fittings from the pole and refixing them in position and testing complete as required and as directed by the Engr-in-Charge. Note :-(i) Unserviceable parts required to be replaced with new one shall be measured and paid separately as "Supply only" against respective items of this Schedule. (ii) Cost of replacement of worn out wire of the fittings and connections as per existing size of conductor of the each fittings is deemed to be included in unit rate quoted.

Supply only Driver for LED 25 watt complete all as directed by Engr-in-Charge.(Make-Bajaj/Havell's/ Crompton/Halonix/Wipro ).

Supply only Driver for LED 45 watt complete all as directed by Engr-in-Charge.(Make-Bajaj/Havell's/ Crompton/Halonix/Wipro )

Supply only Driver for LED 60 watt complete all as directed by Engr-in-Charge.(Make-Bajaj/Havell's/ Crompton/Halonix/Wipro )

Supply only Surge protector for LED 25 to 90 watt complete all as directed by Engr-in-Charge. (Make-Bajaj/Havell's/ Crompton/Halonix/Wipro )

Supply and fix in repair energy efficient LED street light fitting of 45 watt made up of pressure die cast aluminium housing with toughened glass and high power LEDS with secondary optics, efficacy 110/120 LPW, IP 66 protection asthetically designed for all weather conditions with efficient thermal management including 10 KV SPD complete all as directed by Engineer in Charge. Make: Halonix Cat No : HLSLD-09H-45-CWL-R-SPD-HL2-P or equivalent model of Havells, Bajaj, Wipro, Crompton

Supply and fix in repair energy efficient LED street light fitting of 60 watt made up of pressure die cast aluminium housing with toughened glass and high power LEDS with secondary optics, efficacy 110/120 LPW, IP 66 protection asthetically designed for all weather conditions with efficient thermal management including 10 KV SPD complete all as directed by Engineer in Charge. Make: Halonix Cat No : HLSLD-01-60-CWL-R-SPD-HL2-P or equivalent model of Havells, Bajaj, Wipro, Crompton

Supply and fix in repair energy efficient LED street light fitting of 72 watt made up of pressure die cast aluminium housing with toughened glass and high power LEDS with secondary optics, efficacy 110/120 LPW, IP 66 protection aerodynamically designed for all weather conditions with efficient thermal management including 10 KV SPD complete all as directed by Engineer in Charge. Make: Halonix Cat No : HLSLD-01-72-CWL-R-SPD-HL2-P or equivalent model of Havells, Bajaj, Wipro, Crompton

S&F in repair highly efficient integral type LED flood light of 80 Watt made of pressure die cast aluminium housing with toughened glass cover specially designed for LED's with secondary lens optics, and 10 KV SPD and IP 66 protection complete all as specified and as directed . Make: Halonix Cat No: HLFLD-ML11-80-CWL or equivalent in Havells, Bajaj, Crompton, Wipro

S&F in repair highly efficient integral type LED flood light of 100 Watt made of pressure die cast aluminium housing with toughened glass cover specially designed for LED's with secondary lens optics, and 10 KV SPD and IP 66 protection complete all as specified and as directed . Make: Halonix Cat No: HLFLD-ML11-100-CWL or equivalent in Havells, Bajaj, Crompton, Wipro

S&F in repair highly efficient integral type LED flood light of 150 Watt made of pressure die cast aluminium housing with toughened glass cover specially designed for LED's with secondary lens optics, and 10 KV SPD and IP 66 protection complete all as specified and as directed . Make: Halonix Cat No: HLFLD-ML27-150-CW-R01 or equivalent in Havells, Bajaj, Crompton, Wipro

Supply & Fix GI pipe light grade 50 mm dia for cable protection laid in trenches under road/culvert etc complete all as specified and as directed.

Supply & Fix GI pipe light grade 50 mm for cable protection fixed to poles/bldg incl two Nos MS clamps made to shape out of 25 x 3mm MS flat and painting incl bolt, nut, washer etc, complete all as directed by Engr-in-Charge.

Excavation in post holes (or similar holes) each not exc 0.5 cum getting out , returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard/dense soil, complete all as directed by Engr-in-Charge.

Supply and errect steel tubular poles, type-410 SP-22, 9.0 meter long complete with cast iron base plate, finial taper plug, bolts, nuts & screws all as specified and directed.

M&L for PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation filling & mass concrete for sub base of poles, complete all as directed by Engr-in-Charge.

M&L for PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in foundation filling & mass concrete, complete all as directed by Engr-in-Charge.

M&L for cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in copings of poles etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified & directed.

Supply and fix in repair LED post top lantern (garden light) with B-22 base lamp holder and LED bulb of 9W aesthetically designed landscape and diffused lighting mounted on and including 1.5 mtr length GI pipe of 50 mm dia duly black painted and necessary arrangement for cable connection and foundation complete all as specified and as directed.

Supply and lay in repair LT service cable 6 sqmm 2 core inside PVC conduit 20 mm dia medium grade for landscape lighting/ garden lighting inside trench or on wall/floor complete all as specified and as directed. Note: The rate quoted must be inclusive of laying the cables in trench at max 10 cm depth or mounting on floor/wall

Supply and fix GI pipe bracket for street light fittings made out of 32 mm dia GI pipe light grade 1.5 mtr long bent to required angle/ shape with and including necessary clamps, nuts, bolts, & washers of suitable size all as directed by Engineer - in - Charge

S & F PVC weather proof loop-in loop-out box with 4 pole terminal block mounted on porcelain or bakelite and MCB SP 06 Amps for controlling including necessary clamps for mounting on pole etc complete all as specified and directed. Make: Sintex Cat Part No-GSJB 2014 or techno commercially equivalent.

M&L PVC insulated twin core 1100 volts grade 2.5 sqmm copper cable incl connecting up with loop in box to security light fitting complete all as specified and as directed.

S&F Rigid non-metallic PVC conduit 20mm dia fixed to pole inclusive of all fixing accessories such as MS clamp,nuts,bolts etc complete all as specified and as directed.

Supply and fix automatic Street light timer nature switch using Infrared sensor tecnology based, three phase 5-8 KW with 03 Nos 16 Amps Contactor rating and three Nos Outgoing MCB of 20 Amp, enclosed in a pole /wall mounted rust proof, electric shock proof, termite proof and FR grade thermoplastic polycarbonate enclosure (with hinged lid) conforming to IP66 protection class 2. The circuit should also have provision for manual operation (i.e. sensor By-pass operation) and nature switch operation shall be based on natural light lux level i.e. automatic switching ON at Dusk (≤60 lux) and switching OFF at Dawn (≥10 lux) including necessary wiring complete all as specified and as directed. Make Healer Enterprises Model Swadeep-66-5KW3P with Hensel enclosure confirming IP 66 or equivalent make in Havells/Indoasian

Supply and fix 60 W LED inverter street light luminaire with the following functions (a) Real time clock for automatic ON -OFF and dimming option as 100% at 1800 hrs and then 30% at 2300 hrs, 50% at 0400 hrs and switch off at 0600 hrs (b) In built lithium ion battery 3.7 V for 1.5 to 02 hrs power back up for operation at 15-20% of rated wattage in case of power failure with red indication for 230 V AC available and green blinking for battery charging and green stable for for battery fully charged. (c) Versatile pressure die cast alluminium alloy housing with specially designed integral cooling fins top maintainable , clear toughened glass and high efficient secondary lens with IP 66 protection and isolated compartment for driver and control gear. (d) LM 80 certified LED with 50000 burning hrs and system lumen efficiency 110 lm/W (e) Open and short circuit protection, reverse polarity protection , high voltage cut off at 300 ± 10 V and 5 KV internal surge protection, operating voltage 140 V to 270 V and operating temperature -10 ℃ to 50 ℃, complete all as directed by Engr-in-Charge. Make Halonix Cat part No LED SLHSLD-ML04-60-CWL-INV-DIMM-IRSEN-R or equivalent make in Bajaj/Havells, Wipro/Crompton

Supply and fix LED bollard light 10 W, 240 V 50 Hz, CCT 5700 K, integrated electronic driver with internal wiring of copper cable and terminal block for connecting to incoming cable, open & short circuit protection, surge protection, body made of metallic pipe structure and aluminium base of 1.0 mtr length , glare free opal PC diffuser,360 degree lighting, IP 65 protection, resistance to corrosion including bolts for fixing and PCC (1:3:6 ) for foundation complete all as directed. (Make :- Halonix cat no HLOB-05-10-CW-1M or equivalent in Wipro/Havells/Crompton)

Supply and fix three way,(one incoming and two outgoing), three terminal connector suitable for copper cable of size 2.5 sqmm made of bakelite and necessary screws for connecting the cable complete all as specified and as directed.

Supply and fix junction boxes made of plastic round/square shape with four terminals concealed in wall/steps for housing three way connector along with cover plate complete all as specified and a directed.

M & L Repairs to High Mast light fittings (60 to 150 watts, 230/240 volts of any make) at site including taking down existing fittings from high mast (up to16 Mtr hight) and refixing the same in position by means of crane/ manually after replacement of unserviceable/defective part(s) of the fittings, greasing and lubrication of the whinch motor and gearbox as required to make it functioning smooth serviceable condition and testing complete all as directed by the Engr-in- Charge. Note: Flood light fittings if required to be replaced will be measured in relevant items.

Supply and fix in repair LED post top lantern of 45 W, IP 65 protection with in built electronic driver and aluminium housing in pure polyster UV resistant powder coated black finish, top maintainable product with top opening die cast cover , anti corrossive stainless steel screws & silicon gasket, HET PMMA diffuser conforming to IS 10322 Part 5/Sec 1: 1987, suitable for pole diameter up to 75 mm , cable entry through pole from bottom, 3 way 10 Amps GFP mains connector duly wired upto terminal block complete all as specified and as directed. Make Halonix Cat part No: HLPT-04-45-CW or equivalent in Bajaj, Crompton, Havells, Wipro

Shriyansh sales and services (BID ID -3510467)

Rama Electricals (BID ID -3510723)

GRID SYSTEMS (BID ID -3510703)

PURVA ELECTRICALS AND ENGINEERS (BID ID -3510829)

R K ENTERPRISES (BID ID -3509769)

PAUL REFRIGERATION (BID ID -3516909)