SPECIAL REPAIRS TO BLDG No. NH-47 AND T-124 OF SUPPLY LOCATION OF 5136 COY ASC COMP AT KARCHAM UNDER GE 863 EWS

Amount

Dismantling plain or corrugated steel sheeting any gauge, thickness, including Naintal or similar pattern roof coverings complete all as specifed.

0.63 mm thick galvanised corrugated mild steel sheeting with two corrugation side lap fixed with coach screws and washers, in roof, walls etc with grade of zinc coating 275 complete all as specifed.

All as per item No.2 above bit except sheet Note : Sheet obtained from dismantling shall be used

Dismantling mild steel work of any description not otherwise provided for complete all as specifed.

Mild steel roof trusses (framed), Trussesd, purlins, rails and framings and heavy bracket framing (Beam,tee, angle, channel or flat sections) confrming to Fe 410-W (Gde-E-250) Quality 'A' including cleats,distance pieces etc complete all as specifed.

Preparation of new steel surfaces of any description over 10 cm wisth or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specifed.

Preparation of old steel surafaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specifed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets complete all as specifed.

4 mm thick Ply wood, grade BWR, type BB fixed with screws to timber frame work in partitions/ shutters, ceiling etc complete all as specifed.

Second class hard wood plain fillets, wrought, square, rectangular or triangular in section, secured with screws, cross sectional area exceeding 3 and not exceeding 6 Sq. cm complete all as specifed.

18/19 mm thick prelaminated particle board, exterior grade, one side laminated and other side balancing white lamination, fixed with screws to timber frame work in cup board shutters/ shelves, fixed in repair complete all as specifed.

Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specifed and directed..

10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh measured and paid separately under relevant items ) complete all as specified.

Dismantling unframed timber scantlings 40 Sq. cm and over in section and in any position complete all as specifed.

2nd class hard wood in scantling clean sawn timber framed and fixed complete all as specifed.

All as per item No.15 above but except timber. Note : Timber obtained from dismantling shall be used.

Dismantling of unframed fillets, rails, posts, rafters, purlins etc., under 40 Sq. cm in section complete all as specifed.

50 mm thick 2nd class hard wood boarding clean sawn with butt joints fixed with nails in any situation(except flooring and skirting) complete all as specified.

Taking down shutters of any description not exceeding 1 sqm each complete all as specifed.

Taking down shutters of any description exceeding 1 sqm but not exceeding 2 sqm each complete all as specifed.

Refixing shutters of any description not exceeding 1 sqm each in the same openiong complete all as specifed.

Refixing shutters of any description exceeding 1 sqm but not exceeding 2 sqm each in the same opening complete all as specifed.

Taking down chowkats or frames not exceeding 1.5 sqm each (without taking off shutters from the frames) complete all as specifed.

Taking down chowkat or frames exc 1.5 sqm but not exc 4 sqm each (without taking of shutters from the frame) complete all as specifed.

Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specifed.

35 mm thick second class hard wood, plain framed , panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wooden particle board with commercial face veneers supplied and fixed to chowkhats complete all as specifed.

35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specifed.

35 mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars) chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specifed.

30 mm thick Second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. for windows and ventilators etc complete all as specifed.

150 mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specifed.

125 mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specifed.

75 mm long extruded aluminium alloy anodised butt hinges with galvanized mild steel hinge pin type C 21 complete all as specifed.

100 mm long extruded aluminium alloy anodised butt hinges with galvanized mild steel hinge pin type C 21 complete all as specifed.

125 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specifed.

150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specifed.

Aluminium alloy, anodised, sliding door bolt 250mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specifed.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor with overall length of cover plate 140 mm complete all as specified.

Aluminium (extruded section) body door closer hydraulically regulated designation No 3, universal type suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, fixed in repairs complete all as specifed.

4 lever mortice lock brass vertical type size 100 mm complete all as specifed.

Galvanized mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks, or galvanized wire staples complete all as specifed.

300mm mild steel ordinary rat tail rod pattern springs, including roller and roller plate complete complete all as specifed.

Mild steel framed work such as grills, gratings,framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, and similar work confirming to Fe 290. Gde -E-165 complete all as specifed.

3mm Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specifed.

5.5 mm Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specifed.

French polishing two or more coats on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new work complete all as specifed.

Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of pink primer complete all as specifed.

Preparation of old painted wooden surfaces of any descripton over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Galvanized mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks, or galvanized wire staples fixed in repair complete all as specifed.

20 mm dia., aluminium anodised curtain rails with brackets fixed in repair complete all as specifed.

Demolition of stone slabs and tiles of any description or thickness in floors/dado etc laid bedded and pointed in any mortar complete all as specifed.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specifed.

Sand filling under floors or in foundations including watering and consolidation complete all as specifed.

Cement concrete 1:2:4 Type B1 (using 20 mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specifed.

Demolition of un-reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specifed.

25 mm thick PCC 1:2:4 type B0 (Using 12.5 mm graded stone aggregate) as in sub base in floors complete all as specified.

75 mm thick cement concrete 1:3:6 type C2, (using 40 mm graded granite stone aggregate) in sub base of flooring/ hard standing /footpath complete all as specifed.

75 mm thick cement concrete 1:3:6 type C2, (using 40 mm graded stone aggregate) in plinth protection, finished even and smooth without using extra cement complete all as specifed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specifed.

Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specifed.

Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 11 sqm but not exceeding 0.18 sqm, in floors/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specifed.

Screed bed or bedding layer of mortar 15 mm thick cement mortar 1:4 for laying floor finishes to receive floor tiles/granite complete all as specifed.

Coloured glazed ceramic tiles in vertical surfaces 350 x 250 x7 mm/ 450 x 350 x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specifed.

Rendering 10mm thick in cement mortar 1:4 on stone masonry surfaces or surfaces other than fair face of brick work to receive glazed tiles/granite complete all as specifed.

Demolition of stone /boulder masonry, built in cement mortar including all quoins, arches, pillars, etc., but including ashlar facings, dressed stonework and precast concrete articles complete all as specifed.

Pre - cast cement concrete 1:3:6 type C-1, (using 20mm graded stone aggregate) block masonary with solid blocks built in cement mortar 1:6 complete all as specifed.

Walling of random rubble stone masonry uncoursed well bonded bedded and solidly hearted built in CM 1:6 complete all as specified.

Precast PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as bond stones set in cement mortar 1:6 complete all as specified.

Taking down cement plastering of any description on brick or stone wall etc including raking out joints hacking for key scrubbing down with water etc and removal of debris and depositing where directed complete all as specified.

Rendering 15mm thick on fair faces of concrete work in CM 1:6 surface finished even and smooth without using extra cement complete all as specified.

Rendering 15mm thick on fair faces of concrete work in CM 1:4 surface finished even and smooth without using extra cement complete all as specified.

Rendering 15mm thick on stone masonary surfaces in CM 1:4 surface finished even and smooth without using extra cement complete all as specified.

1 mm thick white cement based wall care putty on plastered wall surfaces and applying two coats of oil emulsion distemper over a coat of primer complete all as specified.

Preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified.

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over acoat of primer complete all as specified.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified.

Plain/ reinforced cement concrete 1:2:4 Type B1 (using 20 mm graded stone aggregate) cast in situ in lintels up to 1.5 metre span, cills and other similar bands, plinth courses, parapets, copings, bed plates and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified.

RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in beam, cantilever,lintel over 1.5 m span complete all as specified.

Precast cement concrete 1:3:6, type C1 (using 20 mm graded stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified.

PCC 1:3:6 type C-1 (using 20 mm graded stone aggrgate) in coping complete all as specified.

Reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in chajja , shelves etc complete all as specified.(Note :- Reinforcement shall be measured and paid separately under relevant item)

Use and waste of form work rough finished surfaces of concrete to chajja ,shelves , troughs and similar items including edges complete all as specified.

Use and waste pf form work rough finished surfaces of concrete to sides and soffits of beams , lintel and similar items complete all as specified.

Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified.

Mild steel TMT bars 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for stirrups, hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified.

Dismantaling water tanks exc 500 but n. exc 1000 ltrs capacity and removing to store complete all as specified.

Rotational moulded polyethylene water storage tanks (cylindrical, vertical with closed top) of 1000 Ltrs capacity triple layered hoisted and fixed in position including 20mm bore PVC float valve complete all as specified.

Taking up or down 15 mm bore steel water tubing and connections including cleaning for refixing or removing to store complete all as specified.

Taking up or down 20 mm bore steel water tubing and connections including cleaning for refixing or removing to store complete all as specified.

15 mm bore galvanized steel tubes, medium grade fixed to walls and ceilings or laid in floors complete all as specified.

20 mm bore galvanized steel tubes, medium grade fixed to walls and ceilings or laid in floors complete all as specified.

Refixing old steel tubing of 15 mm bore and connections in new or old position (walls, ceilings, floors etc.) complete all as specified.

Refixing old steel tubing of 20 mm bore and connections in new or old position (walls, ceilings, floors etc.) complete all as specified.

15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions fixed in repairs complete all as specified.

15 mm bore bib taps cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fixed in repairs complete all as specified.

15 mm bore pillar taps, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe fixed in repairs complete all as specified.

Towel rail 600 mm long of PTMT fixed with and including chromimum plated brass screws and wooden plastic cleats (Min weight 190 gms) complete all as specified.

Push taps 15 mm of any colour of PTMT for urinals fixed in repairs complete all as specified.

Glass shelf with sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long fixed in repairs complete all as specified.

PVC Connections 15mm size 450 mm long with PTMT nuts complete all as specified.

Wash basins 550x400mm vitreous china (flat back type) including cutting for and pinning in end of brackets for erecting stand including waste fittings fixed in repairs complete all as specified.

PVC valveless, syphonic action type flushing cistern, 10 litres capacity, low level , white, with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dia fixed in repairs complete all as specified.

Vitreous china wash down water closet pan (Pedestal pattern) white complete including seat and cover including all joints fixed in repairs complete all as specified.

Vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; flush pipe, grating and union for discharge pipe fixed in repairs complete all as specified.

PVC (SWR) floor trap , plain with grating including jointing with solvent cement 75 mm dia complete all as specified.

Grating doom 100 mm size of PTMT (min weight 25 grams) complete all as specified.

32 mm dia low density polyethylene pipe (LDPE) of pressure rating 6 Kgf per cm Square fixed to walls, ceilings or in floors etc. complete all as specified.

50 mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 Kgf/ Sq. cm., fixed complete to walls, ceilings or in floors etc. complete all as specified.

Excavation in trenches n. exc. 1.5m wide and n. exc. 1.5m in depth for foundation and getting out in hard/ dense soil complete all as specified.

Demolition and breaking up drain pipes , 100 mm dia (Salt glazed stone ware, AC or reinforced concrete) set in cement mortar complete all as specified.

PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipe 100mm dia including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified.

110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches complete all as specified.

Returning filling in including spreading, levelling , watering and well ramming in layers not exc 25 cm complete all as specified.

Removal of excavated surplus soil to a distance exc. 1.5 Km but not exc 5.0 Km and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified.

Taking down old unserviceable copper/aluminium point wiring (light, fan, socket or power) complete including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc & making good disturbed surfaces of walls/floors etc complete all as specified.

Taking down unserviceable main switches, DBs/ changeover switch alongwith teak wood boards etc and making good the disturbed surfaces of wall/ floors to match the existing surface complete all as specified.

Point wiring with 1.5 sqmm multistranded, 1100 volt grade copper conductor cable of FRLSH PVC insulated and unsheathed type alongwith 1.5 sqmm PVC FRLSH insulated stranded copper conductor cable for continuous earthing in and including PVC casing and caping with accessories having ISI mark fixed on wall surfaces/ ceiling including provision of PVC box of appropriate size for fixing switches, sockets etc all as specified for the following:-

One light point / fan/ bell point controlled by one switch

One socket 3 pin 5 A pin socket outlet 5 Amps on same board.

One socket 3 pin 5 A pin socket outlet 5 Amps on independent board.

Point wiring with 4 sqmm multistranded, 1100 volt grade copper conductor cable of FRLSH PVC insulated and unsheathed type alongwith 4 sqmm PVC FRLSH insulated stranded copper conductor cable for continuous earthing in and including PVC casing and caping with accessories having ISI mark fixed on wall surfaces/ ceiling including provision of PVC box of appropriate size for fixing switches, sockets etc all as specified.

Switch piano flush type single pole one way 5/ 6 Amps complete all as specified.

Lamp holder angle/ batten type insulated body with back plate fixed in repair on PVC block complete all as specified.

Socket outlet 5 pin 5/6 Amps flush type multipurpose suitable for 3 pin / 2 pin plug fixed in repair complete all as specified.

Switch piano 15 amp 230 volt flush button single pole one way fixed in repair complete all as specified.

Socket outlet 2 in 1, 3 pin 5/6 A and 3 pin 15/16 Amps flush type fixed in repair complete all as specified.

Ceiling rose surface bakelite 3 terminals fixed in repair on PVC block complete all as specified.

LED integrated batten tube light fittings 20 W 4 feet long complete up with twin core twisted flexible copper conductor cable of size 23/ 0.0076 complete all as specified. Make: C&S Cat No. LTTB4F20WLED/W or its equivalent in the makes mentioned in Appendix 'B'.

DB SPN sheet metal enclosure double door suitable for mounting MCB 240 volts with busbar 8 way fixed in repair complete all as specified.

MCB SPN 230 Volts 40 Amps C series 10 KA short circuit breaking capacity complete all as specified.

MCB SP 230 Volts 6-32 Amps C series 10 KA short circuit breaking capacity complete all as specified.

Street light fitting for 35 watt LED with lens , compact street light fitting with die cast aluminium housing complete with toughened glass including surge protector and electronic driver and provn of PVC cable 1.5 sqmm 3 core 1.5 metre long from fitting to ceiling rose including suitable GI bracket , 1.2 metre long made out of GI tubing medium grade 40 mm bore, clamp nut , bolt, washers etc complete all as specified. Make: Havells Cat No. 35WLED757SASYBOPC or its equivalent in the makes mentioned in Appendix 'B'.

LED lamp 9 W retrofit having 850 lumen (NOM) , 6500 K complete all as specified.Make: CG Cat No. LSW-9W-CDL -BC or its equivalent in the makes mentioned in Appendix 'B'.

Earthing with galvnanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below the ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or of steel all as shown in electric plate no. 3 of SSR Part 1 2009 connected to main switch board all as specified and tested on completion including necessary excavation and earthwork in any type of soil, PCC works and CI earth pit cover with watering pipe 20 mm dia GI pipe medium grade, funnel with wire mesh and lugs and GI pipe 15 mm dia light grade for protection of earth lead complete all as specified.

1100 Volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4 mm suspension wire one twin core cable flat of size 10 sqmm complete all as specified.

Sub main wiring (surface) with two single core 04 sqmm FRLSH PVC insulated unsheathed stranded copper conductor cable drawn through and including 20 mm dia PVC casing caping including accessories such as elbow, tee etc and one single run of 4 sqmm FRLSH PVC insulated unsheathed stranded copper earth cable connected to common earth dolly complete all as specified.Note : Tree runs of 4 sq mm cable and one run of PVC casing and capping shall be measured as one unit.

LED bulkhead light fitting 10 Watt environmental friendly , ultra modern , energy saving , surface mounted decorative oval bulk head edge fit LED luminaire comprising of high brightness LEDs including connection of flexible copper wire 2 core from fitting ceiling rose/ connection point complete all as specified. Make: Havells cat No. RUGBYNEONFT10WLED 850SSYMTOPC or its equivalent in the makes mentioned in Appendix 'B'.

House service bracket (hook type) with 3 metre long GI pipe 40 mm bore medium grade , two nos. 90 degree bends, MS hook and stay or guy complete all as specified.

M/S JASWANT SINGH ANAND

Kusan Enterprises

m/s jupiter builders