Upgradation/Beautification of Tourist Places in Bicholim Taluka Regd Development of Harvalem Falls Beautification and providing Tourist facilities at Rudreshwar Temple premises

Amount

Earthwork in excavation over areas by mechanical/manual means in all type of strata comprising any of the materials such as soil, silt, sand, clay, gravels, moorum of all varieties, shingles, pebbles, all types of conglomerates, all types of laterite rock, soft rock, disintegrated rock, fissured/ shattered/ decomposed rock or weathered rock and all such other materials as described under appendix to these specifications whether in full or in parts as the case may be adopting any approved method or methods as may be convenient or permitted inclusive of chiselling, wedging etc. in all conditions such as dry, moist, saturated, submerged, foul conditions etc.blasting prohibited including pumping or bailing out water including segregating the excavated earth/rock and disposal of surplus excavated earth at contractors identified site(at risk and cost of the contractor)for all leads and lifts and as directed by Engineer .

Earthwork in excavation for foundation pipeline trenches by mechanical/mannual means in all type of strata comprising any of the materials such as soil, silt, sand, clay, gravels, moorum of all varieties, shingles, pebbles, all types of conglomerates, all types of laterite rock, soft rock, disintegrated rock, fissured/ shattered/ decomposed rock or weathered rock and all such other materials as described under appendix to these specifications whether in full or in parts as the case may be adopting any approved method or methods as may be convenient or permitted inclusive of chiselling, wedging etc. in all conditions such as dry, moist, saturated, submerged, foul conditions etc. blasting prohibited including pumping or bailing out water including segregating the excavated earth/rock and disposal of surplus excavated earth at contractors identified site at risk and cost of the contractor) for all leads and lifts and as directed by Engineer .

Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers (excluding rock) not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer.

Disposal of material/excavated earth upto a lead of 20kms by mechanical transport including laoding,unloading and stacking ( i ) Lime,moorum, building rubbish

Disposal of material/excavated earth upto a lead of 20kms by mechanical transport including laoding,unloading and stacking (ii) Earth

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Pre-cast cement concrete solid block masonry of compressive strength 70 kg / cm2 in cement mortar 1:4 (1 cement : 4 corase sand ) in foundation and plinth size of blocks (30 x 20 x 15) in foundation and plinth

Pre-cast cement concrete solid block masonry of compressive strength 70 kg/cm2 in cement mortar 1:4 (1 cement : 4 corase sand ) in foundation and plinth size of blocks (40 x 20 x 15) in foundation and plinth

Pre-cast cement concrete solid blocks masonry of compressive strength 70 kg / cm2 in cement mortar 1:4 (1 cement : 4 corase sand ) in partition walls size of blocks (30 x 20 x 10)

Pre-cast cement concrete solid block masonry of compressive strength 70 kg / cm2 in cement mortar 1:4 (1 cement : 4 corase sand ) in foundation and plinth size of blocks (30 x 20 x 15) Extra for precast concrete block masonary in all sizes in superstructure from floor one level upto floor V level

Extra for precast concrete block masonary in all sizes in superstructure from floor one level upto floor V level

Proving and laying dressed uncoarsed Random Rubble laterite masonry thichness as specified as a facia wall (Concrete block masonry) in cement mortar 1:3 (1 Cement : 3 sand) filling the joints with cement mortar mixed with pigment matching to that of adjacent laterite stone colour, all complete as directed by Engineer Incharge

Providing, laying in position, line & level minimum 75mm thick using Patradevi type exposed laterite stone (350x300x160mm) of strength not less than 70 kg/cm2. cladding work ( machine cut edges/Hand dressed for wall lining etc. backing filled with a grout of 12mm cement mortar 1:4 (1 cement : 4 fine sand) including ruled pointing in white cement mortar 1:2(1 cement : 2 fine sand) with an admixture of pigment matching the stone shade brought to line and level. Including scaffolding as directed by the Engineer-in-charge,curing etc complete.

Exposed decorative laterite masonry using Patradevi stone of size as specified and laid as directed by architect in cement mortar 1:4 (1 cement : 4 coarse sand)

Extra for labour in well lining cornices coping, etc.

Laterite masonry in neatly dressed stones for 23 cms thick masonry walls in c.m. 1 : 4 (1 cement : 4 coarse sand in foundation upto plinth level

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: All works upto plinth level

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: In retaining walls , return walls(any thk) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping bed blocks, anchor blocks, plain window sills, fillets etc, upto floor five level.

Providing & laying cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: All works upto plinth level

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size) All works upto plinth level

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size) In walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and structs etc. upto floor five level

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size) In beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases upto floor five level

Reinforced cement concrete work in arches, arch ribs, domes, vaults, shells, folded plate and roofs having slope more than 15° upto floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1½ :3 (1 cement: 1½ coarse sand: 3 graded grantic or basaltic aggreate 20mm nominal size)

Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards upto floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1½ :3 (1 cement: 1:1½ coarse sand: 3 graded stone agg 20mm nominal size)

Providing and laying in position ready mixed concrete (RMC) with usage of Ordinary Portland Cement manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead upto 10kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering, shuttering, finishing and reinforcement including the cost of admixtures in recommended porportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without imparing strength and durability as per the directions of the engineer- M-30grade of concrete

Vaccum dewatering of laid concrete for roads/ areas using Tremix machinery including formwork with MS channel/ angle sections on sides of concrete with proper supporting system, surface/screed & needle vibrating & levelling of concrete. Vaccum dewatering should be done using suction mats (spread on surface) & suction pump, power floating/ troweling using screen floater, manual spreading of hardening compound (if any), smooth/rough/broom finish to the required slope, camber & level, groove cutting (upto 10mm wide x50mm deep) for contraction/expansion, construction & longitudinal hoints, Providing dowel bars with sleeve/tie bars, filling two component polysuphide sealant/joint filler (Bitumen hot sealing compound: Grade A), taping with masking tape etc complete. (Concrete, reinforcement, Dowel Bar with sleeve/tie bar Reinforcement, tarpaulin sheet to be paid separately)

Centering and shuttering including strutting, proping etc. and removal of form for. Foundations, Footings, Bases for columns

Centering and shuttering including strutting, proping etc. and removal of form for. Vertical surfaces such as retaing walls, return walls, Partitions, walls (any thickness) including attached Pilasters, Buttresses, Plinth and string courses, Fillets and the like

Centering and shuttering including strutting, proping etc. and removal of form for. Columns, Piers, Pillars, Aburments, Posts and struts (square rectangle polygon in plan)

Centering and shuttering including strutting, proping etc. and removal of form for. Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, Bressumers and Lintels plinth beams not exceeding 1m in depth

Centering and shuttering including strutting, proping etc. and removal of form for. Staircases (except spiral staircases) excluding landing

Centering and shuttering including strutting, proping etc. and removal of form for. Arches, domes, vaults upto 6.00 span

Centering and shuttering including strutting, proping etc. and removal of form for. Extra for arches, domes, shell roofs exceeding 6m. Span.

Centering and shuttering including strutting, proping etc. and removal of form for. Domes, vaults, shell roofs having curved surface in both the directions.

Centering and shuttering including strutting, proping etc. and removal of form for. Suspended floors, roofs landings, shelves & their supports

Centering and shuttering including strutting, proping etc. and removal of form for. Vertical or horizontal fins individually forming box louvers or projected bands

Centering & shuttering including Strutting, Propping & removal of forms for sloping or battering surface (slabs, beams, louvers, etc) including folded plates Columns, Pillars, Posts & struts (circular or curved in plan)

Centering & shuttering including Strutting, Propping & removal of forms for sloping or battering surface (slabs, beams, louvers, etc) including folded plates Cornices & Mouldings

Extra to be added for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de- shuttering and de-centering at all levels, over a height of 3.5m, for every additional height of 1m or part thereof. (Plan area to be measured) Suspended floors, roofs, landings, beams and balconies (plan area to be measured)

Extra for shuttering in circular work (20%)

Providing corrosion resistant steel CRS-50 bars of (SAIL, TATA, VIZAG, JSW Steel Ltd.)(Confirming to IS 1786 if 1985) for RCC work including bending, binding & placing in position in all the floors along with factory made precaste concrete cover blocks of specified s izes whose compressive strengthis not less than that of surrounding concrete in the structural member .

Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member.

Providing & fixing M.S grill of required pattern of windows with M.S flat square or round bars with provision for anchor fastning including the cost of welding etc complete as directed by Engineer-In-Charge

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of approved make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc.with hairline finish, including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing & Fixing in position Double Skin roof with Zincalume/ Galvalume colour coated & bare profile sheet with subtle square fluting factory cut at all heights for roof, side & Gable cladding complete in all respect. TOP SHEET-The end rib shall be designed for anti-capillary action. The feed material should be manufactured out of nominal 0.45 mm Base Metal Thickness (BMT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 43.5% Zinc &1.5% Si) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides) with quality paint coat as per AS/NZS 2728 type 3-4. The paint shall have a total coating thickness of nominal 35 μm, comprising of nominal 20 μm exterior SMP coat on top surface and nominal 5 μm reverse backer coat on back surface over nominal 5 μm primer coat on both surfaces of approved colour shade. Total Coated Thickness (TCT) should be 0.50mm. Total Painted Thickness (TPT) should be in addition to 0.50mm. The steel sheet shall be fastened with nominal 40 μm zinc coated or nominal 25 μm zinc-tin alloy coated, Hex head, self-drilling screw as per AS 3566-2002 Class 3 fasteners of approved make with EPDM washer as per the requirement considering the profile shape and design load. The fastener size shall be calculated as per the design or manufacturers recommendations. The profile sheet, fastener size etc. shall be approved by the Engineer. The sheeting should be with minimum 200mm lap & waterproof with Silicon sealant non-hardening neutral cure type shall be applied at all end laps, complete as directed Z-Sub Girt - roll formed section 50x50x50x1.50 TCT, 120GSM Galvanised, High Strength (345 MPa), approximate Wt. 1.85 kg/r.m. fixed with self tapping screws Glass Wool Insulation with FSK facing 50mm with 24 kg/m3 density in between 2 sheets. LINER SHEET-bare galvalume/zincalume roofing sheet of same profile as top sheet. The feed material is of manufactured out of nominal 0.45 mm Base Metal Thickness (BMT) (0.47 mm TCT), Hi- strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 45% Zinc) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides), passivated & resin coated. The feed material should have coil manufacturer’s product details marked at regular interval for confirming genuinity of the material. complete as per the directions of the engineer. The steel manufacturer's test certificate for the chemical & mechanical properties of steel must be submitted for approval prior to installation.

Providing and fixing 15cm wide 45cm overall semi-circular plain G.I. sheets gutter with iron brackets 40 x 3 mm bolts nuts and washers etc., including making necessary connection with rain water pipe complete as per design. 0.80 mm thick sheet

Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins, rafters, trusses, flashings etc. complete as per the directions of the Engineer in charge.

Add for providing & fixing Flashings -[Corners, Ridges, valleys, gable end & Trims] (Girth upto 610mm) including all the accessories complete as per the directions of the Engineer in charge.

Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24/15x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25/15 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24/15 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer. GI Metal Ceiling Lay in perforated Tegular/ Bevelled edge global white color tiles of size 595x595 mm and 0.4-0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

Providing and Fixing Mild Steel drain cover of 900mm width with 75x40x5mm channels and 40x40x5mm angles, flat bars 40x5mm per running meter applying one coat of primer and two coats of painting etc complete as directed by Engineer-In-Charge

Providing and fixing prefabricated gate of M.S hollow sections 49.5x49.5x4.5mm with 12 mm M.S square bars of M.S grill work as per drawing including providing and fixing locking arrangement,pintals,holdfasts embedded in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 granitic or basaltic aggreate 20 mm nominal size)including applying priming coat with ready mixed red lead paint and painting two or more coats with superior ready mixed paint of approved brand and manufacture in all shades as per directions complete.

Steel work in single & built up sections (SAIL, TATA. VIZAG,JSW & using electrodes of Ador or ES4B or Deh Secheron make only) in R.S. joists, channels, angles, tees,flats, tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 (Min Yeild Stress 310 Mpa)) including cutting, hoisting fixing in position and applying a priming coat of red lead paint. , including welding and bolted with special shaped washers etc. complete etc complete as directed by Engineer-in-charge

12mm cement plaster 1:4 (1 cement : 4 fine sand)

6mm cement plaster to ceiling 1: 4 (1 cement : 4 fine sand)

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge.

18mm plastering with terrazzo finish rubbed and polished complete, under layer 12mm thick cement plaster 1: 3 (1 cement : 3 coarse sand) and top layer 6mm thick white black or white and black marble chips of 3mm and down size laid in cement marble powder mix 3: 1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble / powder mix: 7 marble chips) by volume.

Neat Cement punning

Extra for plastering on circular work not exceeding 6m in radius In one coat

Extra for plastering done on mouldings, cornices, or arch it raves including neat finish to line and level. In one coat

12mm thick plain cement mortar bands in cement mortar 1:4 (1 cement: 4 fine sand) 1 meter long, 1 cm wide

Providing and Laying 50mm thick Cement plaster in 1:3 cement mortar (1: cement 3: fine sand) in double layers including chicken mesh fixed in first layer of cement plaster, neatly finished sponge plaster in proper line, level and plumb in curves, mouldings, cornices, projections, bands, grooves, niches etc all complete as directed by Engineer In-charge

Precast plain cement chequered tiles 22 mm thick of required shades laid in floors, treads of steps and landing on 20 mm thick bed of Cement mortar 1:4 (1cement : 4 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete. Medium shade using pigment with 50% white cement 50% Grey cement

Precast plain cement chequered tiles 22 mm thick of required shades laid in floors, treads of steps and landing on 20 mm thick bed of Cement mortar 1:4 (1cement : 4 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete. Dark shades using ordinary cement

Kotah stone slab flooring over 20 mm (average) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) 20 mm thick.

Cuddappah stone slab machine cut flooring over 20mm (average) thickness of cement mortar 1:4 (1 cement : 4 coarse sand laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete - 25 mm thick.

Providing and laying jet black mirror polish granite flooring and dado over 20mm thick base of cement mortar 1:4 laid over and jointed with cement slurry including rubbling complete Granitic slab (jet blck with mirror polish) 20 mm thick add q0% wastage 1.00

Providing and laying 20mm thick cuddapah in shelves over 20 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) etc.complete

Marble stone flooring with 18 mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20mm (average) thick base of cement Mortar 1:4 (1 cement:4 coarse ) using : White Makrana Marble with blue or black veins

Providing and fixing Kota stone tread tiles 35mm thick in single piece with rounded of nosing antiskid groove laid on and including 20mm (average ) thk bed of cement slurry including pointing with pigmented cement slurry to match the shade of the slab, cleaning etc. complete.

Providing and fixing vitrified antiskid tiles (320x320) and 10mm thick tiles in floor, treads of steps, landing on 25mm thick bed of cement mortar 1:3 and jointed with cement slurry complete.

Providing and fixing 1st quality ceramic glazed wall tiles (Johnson, Somany, Kajaria )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete. Wall Ceramic Glazed Tiles : 300 x 600

Providing and and laying scratch resistant floor tiles in different sizes of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete 600x 600 mm Dark Shades

Providing and and laying scratch resistant floor tiles in different sizes of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete 600 x 600 mm light Shades

Providing and fixing 1st quality ceramic glazed wall tiles (Johnson, Somany, Kajaria )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete. 600x 600 mm Dark Shades

Providing and fixing 1st quality ceramic glazed wall tiles (Johnson, Somany, Kajaria )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete. 600 x 600 mm light Shades

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer : Flamed finish granite stone slab. Jet Black

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer : Flamed finish granite stone slab. Elite Brown

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm Jet Black

Jaisalmer stone flooring with 18mm thick polished Jaisalmer stone over 20mm (average) thick base of CM 1:4 (1 cement : 4 Coarse sand) with joints finished flush

Providing and fixing Granite stone slabs (mirror polished) 18mm thick in risers of steps, skirting, dado and pillars laid on cement paste and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete Jet Black

Providing and fixing Granite stone slabs (mirror polished) 18mm thick in risers of steps, skirting, dado and pillars laid on cement paste and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete Elite Brown

Providing and fixing of 18mm thick Mirror Finish Granite slab for urinal partitions with cement etc complete including rounding and polishing of the edges as directed by Engineer-in-Charge

Moulding, Rounding, Edge Polishing, Chamfering of edges of Granite Stone slab to full circle, half circle, slope etc including rubbing and polishing etc complete

Prviding and laying rough kotah stone slab floorin laid on 20 mm thick base of cement mor-tar 1: 4 ( 1cement :4 coarse sand ) jointed with grey cement slurry mixed with pigment to match the shade of the tile etc complete as directed by Engineer-in-charge

Applying one coat of cement primer of approved brand and manufacture on wall surface.

Applying priming coat with ready mixed primer of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior quality ready mixed paint for steel work of approved brand & manufacture in all shades on new work to give an even shade.

Painting (two or more coats) with aluminium paint of approved brand and manufacture on new work to give an even shade.

Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Painting three or more coats with acryllic exterior paint of approved brand and manufacture(such as weather shield,APEX) including applying one coat of cement primer and one coat of surface treatment etc. complete.

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Extra for painting on walls on the outside at height more than 10m from ground level for every additional height of 3.0 m or part thereof.

Providing and applying Synthetic elastomeric coating cum paint of reputed make such as Polysafe or equivalent conforming to relevant IS specification ready to use for bridge structures in saline atmosphere as to avoid salt concentration from marine environment, ultra- violet effects of the sun rays, fungus development and to protect the reinforcement from marine atmoshpheric effects in 3 coats including sand blasting, cleaning the concrete surfaces brushing and applying the polymerbased chemical coating with PRIMER, 1ST COAT and SECOND COAT at an interval of 24 hrs in approved shade and colour including scaffolding etc. (as directed by the Engineer-in- charge) complete with 5 yrs guarantee).

High build, Crack-bridging, Elastomeric, protective and waterproof coating for Concrete & Masonry specially for concrete surfaces of bridges Providing and applying on a well prepared vertical surface which is single component, high performance, acrylic resin based coating for long term protection of concrete & masonry from aggressive atmospheric gases such as, carbon dioxide, sulphur dioxide and chloride ions. The product shall be applied in minimum two coats to achieve total DFT of 300 Microns. The product must be crack-bridging high elongation type with elongation at break, exceeding 300% & tensile strength exceeding 2.5 MPa. The system shall exhibit excellent bond strength with the substrate at least exceeding 1.5 MPa, when tested as per ASTM D 4541. All scaffolding, ladders, supporting materials etc. complete. Rates shall be inclusive of all labour, materials, tools and plant etc. complete.

Protective coating for steel structures-Providing & applying MC Bauchemie's MC Dur ZKE or Equivalent,a two component solvent containing Zinc enriched epoxy resin based protective coating for steel construction in marine climate & for construction which are heavily strained by atmosperic conditions and industrial atmospere which is resistant against solid & dissolved salts ,diluted acid,alkalis as well as oil & fat.The metal surface shall be treated by short blasting with Quartz-free abrasive,sand blasting etc. complete.the consumption shall be 100-300 gm/ m2 in two coats with approved shades including cost of materials,cleaning ,preparing the surface,chipping,removing loose dirt with wire brush & water ,labour.

Providing and Painting (two or more coats) with synthetic enamel paint of approved brand and manufacture in all shades on external wall , including one or two coat of external cement primer, neatly finishing in all levels, cornices, mouldings, grooves, all curved/round surfaces, architectural surcfaces, all complete etc, as directed by Engineer Incharge

Applying breathable, non-reactive, antifungal, and water repellant Silane/ Siloxane chemical as approved by Archaeological Survey of India/ Engineer, of approved brand and manufacture, diluted with solvent mineral Turpentine oil in the ratio of 1:12 (One part of approved chemical :12 Part of Turpentine oil), on the exposed laterite masonry surface with two or more coats to give uniform application of chemical on the surface, all complete as per direction of Engineer. (The rate is inclusive of all materials & labours).

Providing water proofing treatment over the new R.C.C. roofs terrace toilet by spreading cement slurry over the R.C.C. slab and laying of 10cms. Average laterite stone ballast coba with the necessary gradient for easy flow of rain water and the coba in covered with damp proof of Hindustan water proofing co. Or equivalent jointless water proofing plaster of mix 1:3 ( 1 cement : 3 find sand), finished smooth with wooden trowel with false marking of 30 cms square. The vertical surface of the adjoining walls are to be treated upto a height of 30cms including rounding of junction (the rate includes for complete items including labour and materials and including cost of initial treatment of roof slab as follows. The injunction of damp proof or equivalent compound with cement solution will be given as and when found necessary for filling honey comb, cracks etc. in the R.C.C. slabs). NOTE: cement consumption 25 kg/sq.m.

Providing anti – termite treatment to buildings conforming to I.S.S. 6113 part II 1971 (revised) including adopting precautions for health hazards and safety measures as required therein with the cost of all materials, chemicals, plants, equipments required for the treatment and furnishing a guarantee for a minimum period of 10 years from the date of completion including eradicating any infestation of termite free of cost during the guaranty period complete. (The payment will be made on plinth of the building. (a) Pre-construction

Supplying and fixing Pre-cast cement concrete kerb-stones(factory made,the factory should be ISO certified and registered under Dirctorate of Industries, Govt. of India) of M-20 with 20 mm nominal size granitic/basaltic aggregate properly consolidated by mechanical plat-form and vibrators with smooth finish including fixing at site complete as per specification. (b)Size 30 cm L x 40 cm H x 15 cm T

Providing and fixing weepholes with rigid PVC make laid in position with a required slope and level while layingpipes of approved the concrete of retaining wall,wing wall and earth retainig structure complete as directed by the Engineer in charge B) 75 mm dia

Providing and alying 60 mm thick factory made cement concrete interlocking paver block of M30 grade made by heavy duty block making machine with strong vibratory compaction using 3 ton roller and of aprpoved size and design / shape laid in 50 mm thick compacted bed of course sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer. a. Red / Black

Providing and alying 60 mm thick factory made cement concrete interlocking paver block of M30 grade made by heavy duty block making machine with strong vibratory compaction using 3 ton roller and of aprpoved size and design / shape laid in 50 mm thick compacted bed of course sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer. c. Yellow

Supplying jamba wooden bally piles 200 mm mean diameter cut to a length required (not exceeding 9 meters) and planted in position ready for driving: a. Upto 2.5 meters long pile

Heading and pointing whole bally piles 200mm diameter including only rings, providing and fixing pile shoes, cutting of heads after driving and taking out rings removing cut off portions to departmental store as specified.

Driving down wooden piles of 200mm diameter either in vertical or battered work to approved lines and level through various strata including arranging all the appliances necessary for pile complete at site (portion in ground only to be measured) a. Upto 2.5 meters long pile

Demolishing R.C.C. work including stacking of steel bars & disposal of unserviceable within 50 mts. lead.

Demolishing laterite stone masonry in cement mortar including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead.

Dismantling wood work of sectional area 40 sq.cm. and above wrought framed and fixed in frames, other frames and trusses including stacking of material within 50 mts. lead (span upto 10 mtrs.)

Taking out doors, windows and clerestory windows shutters (steel or wood) including stacking within 50 mts. Lead Of area 3 sq.m. and below

Dismantling steelwork in single sections in channels, angles, tees and flats including dismembering and stacking within 50 mts. lead

Dismantling the tile work in floors and roofs laid in cement including stacking of materials within 50 meters lead for thickness of tiles 10mm to 25mm.

Dismantling G.I. sheets roofing including ridges, hips valleys and gutters etc. and stacking the material within 50 meters lead.

Dismantling and removing mangalore roofing tiles from roofs including ridges, hips, valleys, sheets wind ties etc. but excluding battens, roof timber etc. and stacking materials within a distance of 50 mt.

Dismantling and removing mangalore roofing tiles from roofs including ridges, hips, valleys, sheets wind ties etc. but excluding battens, roof timber etc. and stacking materials within a distance of 50 mt

Dismantling rolling shutters, top covers and shafts etc. for replacement of springs ball bearing complete and refixing the shutter after replacement of springs and ball bearing (cost of replacement parts excluded) including all labour and returning the unserviceable parts to the department complete.

Providing and laying 1st class mangalore tile roof covering with 25 x 50mm (1” x 2”) jamba wood or similar batten including nails etc. but excluding rafters.

Providing and laying ridge tiles laid dry & pointed with lime mortar 1: 2 (1 lime: 2 surkhi)

Providing woodwork in frames of doors, windows, clerestory windows trusses & other frames wrought framed and fixed in positon. a. First class Indian teak wood

Providing & fixing 20 mm eaves barge boards 1st class matti wood

Providing and fixing 50 mm thick panelled glazed or panelled and glazed shutters for doors, windows and clerestory window including anodized aluminium butt hinges with necessary screws: First class Indian teak wood

Providing and fixing 35 mm thick panelled glazed or panelled and glazed shutters for doors, windows and clerestory window including anodized aluminium butt hinges with necessary screws: First class Indian teak wood

Providing and fixing 35 mm thick panelled glazed or panelled and glazed shutters for doors, windows and clerestory window including black enameled iron butt hinges with necessary screws: Nano or equivalent

Extra for superior type of glass panes used instead of ordinary glass panes in glazed or panelled and glazed doors, windows, clerestory windows (total area of shutters to be measured).

Providing flat iron hold fast 40 cm including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embeded in cement concrete block 30 x 10 x 15 cm 1:3:6 mix (1 cement: 3 coarse sand: 6 stone aggregate 20 mm nominal size. 40 x 3 mm flat iron hold fast 15 cm long

Providing and fixing bright finished brass door latch with necessary screws etc complete 250 x 16 x 5 mm

Providing & fixing bright finished brass 100 mm. mortice latch & lock & a pair of levers, handles with necessary screws etc. complete (Indian make of approved quality).

Providing and fixing 150 mm. bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete.

Providing and fixing brass hydraulic door closer of make Everest universal 68 or equivalent with necessary screws and fittings complete.

Providing & fixing chromium plated brass tower bolts (barrel type) with necessary screws complete. a. 250 x 10 mm

Providing & fixing chromium plated brass tower bolts (barrel type) with necessary screws complete. c. 150 x 10 mm

Single Colour Foam Core FRP (Fiber Reinforced Polymer) Door Shutter Manufacture, Supply and Installation (including accessories as mentioned below) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) door shutter of specified thickness as per options below by using tray system with seasoned hard wood, moisture less than 17%, wood styles for Top rail and lock rails. FRP (Fiber Reinforced Polymer) laminate made up of 450 grams per sq.mts (gsm) chop strand matt and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps) . The core of shutter will be filled as specified (Expanded Polystyrene Foam / Polyurethane Foam (EPS/PU) Foam). The shutter to be of single colour & water proof as well as mild acid / alkali resistant manufactured using RV TIFAC (R V Engineering College, Bangalore & Technology Information Forecasting & Assessment Council) technology in line with IS 13034 1990 test Standard in an ISO 9001 – 2015 certified factory. Note: For 35 & 40mm thickness shutters, only frames of 5 x 2 ½ Cross section frames to be used. Accessories: i) S. S. Hinges 4” - 3 Nos ii) S. S. Latch - 1 No iii) Tower Bolt 5” - 2 Nos iv) Handle 5” - 2 Nos Shutter Thickness b. 35mm

Providing & fixing Stainless Steel tubular lever D- Type mortise handles with round/Square nose, 24mm Mortise/sash lock body & Strike plate (all SS Finish), Pin cylinder 60mm with one side key and other side knob/thumb turn with necessary screws etc. complete

Providing and fixing chromium plated brass handle with necessary screws etc. complete a. 125 mm

THREE TRACK SLIDING WINDOW:- Providing & fixing Three track Sliding Windows Yashashri make or equivalent, made out of 97mm x 43mm x 2mm upvc multi-cavity reinforced with G.I. channel and having up word projection for sliding of shutter on Nylon Rollers and having slope for draining rain water outside and welded in corners. Shutters are made out of 57mm x 31mm x 2mm multi-cavity section having provision for nylon rollers fixing, glass fixing with EPDM gasket, glass bead and welded in corners. In Three Track Sliding window 4mm clear glass is used. The average weight of Three Track Sliding window is 16.5 kg per sq mtr. These Upvc sections are tested by using BS 2782 & DIN 53459 test methods.

TWO TRACK SLIDING WINDOW (Economical):- Providing & fixing Two Track sliding window in economical section made out of 60mm x 45mm x 2.5mm Upvc multi cavity track section & Shutter made out of 57mm x 31mm x2.5mm Upvc multi cavity section welded in corners with Glass beading & EPDM Gasket & 4mm clear glass with lock & rollers. The average weight of Two Track Sliding window (Economical) is 12.25 kg per sq mtr. These Upvc sections are tested by using BS 2782 & DIN 53459 test methods.

Providing and fixing in position collapsible steel shutters with vertical channels 20 mm x 10 mm x 2 mm and braced with flat iron diagonals 20mm x 5mm size with top and bottom rails of T-iron, 40 x 40 x 6 mm with 38 mm dia. Steel pullys completely bolts locking arrangement, stopper, handles including applying a priming coat of red lead paint.

Supplying and fixing rolling shutters of approved make, made of 80 x 1.25 mm M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5cm long wire springs grade No.2 and M.S. top cover of 1.25mm thick for folling shutterstop cover and spring.

Providing and fixing hydraulic floor spring of reputed make Everrite, prabhat or equivalent as per the manufacturer's as specification having double action spring as approved by the Engineer-in-charge.

Supply and installation of Aluminium Louvers. The frame should be made of Aluminium tubes of size 100x50X1.50 mm thk and 50X25x1.50 mm thk C channels. Aluminium Z shaped louvers of 100mm should be fixed to the supporting frame with aluminium cleats, GI screws, etc complete. The whole assembly is powder coated with pure polyester paint. (MS framing to be paid separately)

Providing & fixing in position fixed glass for shower partition with 10mm toughened clear glass on patch fittings in SS 316 grade, Reinforcement bar, silicone sealant Complete.

Proving and fixing white vitreous china water closet squatting pan (Indian type w.c. pan) size 580 mm with 100 mm sand cast iron P. or S trap 10 litres high level P.V.C. flushing cister (of approved make) with fittings, rack bolts 32 mm diameter P.V.C telescopic flush pipe with fit tings and clamps 25mm P.V.C. over flow pipe with specials & mosquito proof coupling of approved municipal design and nylon pull complete cutting and making good the walls and floors where required. b. Orissa pattern W.C. pan

Proving and fixing white vitreous china Wall Hung type (European Type) water closet with seat and lid with C.I. brass hinges and rubber fittings with flush valve nelson/ similar fully chromium plated with stop cock, wall flanges, flush pipe or elbow and vaccum breaker coupling etc. including chair bracket/rag bolts, cutting & making good the walls and floors where required and concealed seat support - W.C. Pan with white plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm and 340 x 430 x 265 mm sizes respectively with pvc automatic flushing cistern with fittings, R.S. or C.I. brackets, standard size galvanised steel flush pipe and spreaders with brass unions & G.I. clamps complete, including painting of cister and fittings, cutting and making good the walls and floors where required. Range of three urinal basins with 10 litres pvc. automatic flushing cistern .

Providing and fixing table top basin of Jaquar make or equivalent size 420x340x170mm including fancy pillar cock,CP brass chain with rubber plugs,32mm standard CP brass waste,32mm CP brass trap etc.including labours,tools,plants etc

Providing and fixing C. P. brass waste for wash basins and sink 32 mm dia

Providing & fixing 600 x 120 mm glass shelf with C. P. brass brackets and guard rail complete fixed to wooden cleats with C. P. brass screws.

Providing & fixing c.p. brass towel rail complete with C.P. brass brackets fixed to wooden cleats with C. P. brass screws. 600x20 MM SIZE

Providing and fixing toilet paper holder : C.P. brass

Providing & fixing soap dish chromium plated with brackets fixed to wooden cleats with CP brass screw

Providing and fixing flush valve (nelson or similar) fully chrominium plated with stop cock wall flange flush pipe or elbow and vaccu.m breaker coupling etc. complete :

Providing and fixing brass full way valve (heavy) duty of approved quality : 20 mm nominal bore

Providing and fixing brass full way valve (heavy) duty of approved quality : 32 mm nominal bore

Providing and fixing ball valve (brass) of approved quality : High pressure with P.V.C. floats: 20mm nominal bore

Providing and fixing non-return valve of approved quality : 32 mm nominal bore

Providing and fixing P.V.C. connection pipe with brass unions 15 mm nominal bore: 45 cm (18”) length .

Providing and fixing C.P. brass shower rose with 15 or 20 mm. Inlet: 100 mm diameter.

Providing and placing on terrace roof of floor two (1st flor roof single piece rotational moulded polythene water storage tank having I S I mark and conforming to I S 12701; 1996. 1000 lit. capacity

Extra for placing polythene tank on roof of floor three (2nd floor roof) 1000 lit. capacity

Providing and placing single piece rotational moulded polythene water storage tank of 5000 lts capacity having I S I mark and conforming to I S 12701; 1996. etc. complete as per the directions of Engineer-In-Charge

Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with 1: 11/2:3 mix (1 cement: 1 1/2 coarse sand : 3 graded stone aggregate 20mm nominal size foundation concrete 1: 11/2:3 mix (1 cemet:1 1/2 coarse sand :8 graded stone aggregate 20mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) neatly finished complete as per standard design. Inside size 90 x80 cm and 60 cm deep including C.I. cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg.)

Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with 1: 11/2:3 mix (1 cement: 1 1/2 coarse sand : 3 graded stone aggregate 20mm nominal size foundation concrete 1: 11/2:3 mix (1 cemet:1 1/2 coarse sand :8 graded stone aggregate 20mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) neatly finished complete as per standard design. Inside size 60 x 60cm and 60cm deep including C.I. cover with frame (light duty) 455x610mm internal diameter total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg).

Making soak pit. 2.5 m dia 3 m deep with 45x45 cm dry brick honey comb shaft and S.W. drain pipe 100 mm diameter, 1.8 m long complete filled with laterite stone aggregate 125 to 180 mm surrounded by laterite stone aggregate of 40 mm and down gauge as per standard design.

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water) drainage pipes of approved including lubricant etc. complete (single/double) socketed: 110 mm dia

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water) drainage pipes of approved including lubricant etc. complete (single/double) socketed: 75 mm dia

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes including lubricating 110 mm dia

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes including lubricating 75 mm dia

Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door : 100 mm dia

Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door : 75 mm dia

Providing and fixing single tee of rigid PVC (approved make) for S.W.R. pipes including lubricating etc. complete, without door: 110 mm dia.

Providing and fixing single tee of rigid PVC (approved make) for S.W.R. pipes including lubricating etc. complete, without door: 75 mm dia.

Providing and fixing single Tee of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door : 110 mm dia

Providing and fixing single Tee of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door : 75 mm dia

Providing and fixing single “Y” of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with out door : 110 mm dia

Providing and fixing single “Y” of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with out door : 75 mm dia

Providing and fixing U.P.V.C. pipe clips (approved make ) for S.W.R. pipes : 110 mm dia

Providing and fixing R.P.V.C. vent cowl 75 mm dia

Providing and fixing NICKEL chrome plated copper alloy Fancy Pillar Cock rocket type Jaquar make or equivalent. Confirming to IS 8931;1993 15mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy BIB Cock Short Body Jaquar make or equivalent. Confirming to IS 8931;1993 15mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy long body bib cock with wall flance Jaquar make or equivalent. Confirming to IS 8931;1993 15mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy two way long body bib cock with wall flange of approved make. Confirming to IS 8931;1993 15mm dia nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy concealed stop cock with slinding flance 15 mm Jaquar make or equivalent. Confirming to IS 8931;1993 15mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy Angular Stop Cock with wall Flangue Florentine (FLR-5053N) 15MM - Jaquar make make or equivalent. Confirming to IS 8931;1993

Providing and fixing NICKEL chrome plated copper alloy Fancy wall mixer with 3 IN 1 SYSTEM WITH 115MM long bend pipe for connection to over head shower Jaquar make or equivalent. Confirming to IS 8931;1993

Providing and fixing NICKEL chrome plated copper alloy Fancy sink mixer with U shape swinging casted spout Jaquar make or equivalent. Confirming to IS 8931;1993

Providing and fixing NICKEL chrome plated copper alloy Fancy BOTTLE TRAP ECONOMY TYPE 32MM Jaquar make or equivalent. Confirming to IS 8931;1993

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Internal work exposed on wall (Medium duty SDR 13.5 pipe). 40 mm nominal outer dia pipes.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Internal work exposed on wall (Medium duty SDR 13.5 pipe). 50 mm nominal outer dia pipes.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 m. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. 15 mm dia nominal outer dia pipes.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 m. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. 20 mm dia nominal outer dia pipes.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 m. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. 25 mm dia nominal outer dia pipes.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 m. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. 32 mm dia nominal outer dia pipes.

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS: 15778 having thermal stability for hot and cold water supply includng all CPVC plain and brass threaded fittings CPVC solvent cement, trenching, refilling and testing of joints complete as per firectionof the Engineer in charge.(External work (heavy duty SDR 11 pipe) 25 mm nominal outer dia pipes.

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS: 15778 having thermal stability for hot and cold water supply includng all CPVC plain and brass threaded fittings CPVC solvent cement, trenching, refilling and testing of joints complete as per firectionof the Engineer in charge.(External work (heavy duty SDR 11 pipe) 40 mm nominal outer dia pipes.

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS: 15778 having thermal stability for hot and cold water supply includng all CPVC plain and brass threaded fittings CPVC solvent cement, trenching, refilling and testing of joints complete as per firectionof the Engineer in charge.(External work (heavy duty SDR 11 pipe) 50 mm nominal outer dia pipes.

Providing & fixing bevelled edge mirror of superior glass (5mm thk) of approved Quality, shape & size complete with CP brass screws and washers, Cleats, CP studs etc Complete.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 including cutting of stone and making good the walls wherever required. Kitchen sink without drain board. with coupling & all accessories complete with choke stop strainer, Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete. Overall size 610mmx460mm (24"x18") bowl size 560mmx410mmx215mm (22"x16"x81/2") Glossy. 1.0mm thk,

Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/Cuddapah stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing nahani trap of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, without door : 110mm dia

Providing & fixing (4’) 100 mm sand cast iron grating for gully floor or nahni trap.

Providing and fixing square-mouth S.W. gully trap grade ‘A’ complete with c.i. grating brick masonry chamber and water tight C.I. cover with frame of 300 x 300 mm size (inside the weight of cover to be not less than 4.53 kg). And frame to be not less than 2.72 kg as per standard design : 150 x 100 mm size –P or S type

Providing M.S. footrests including fixing in manholes with 20 x 20 x 10 cm cement concrete block 1:3:6 (1 cement :3 coarse sand :6 graded stone aggregate 20 mm nominal size) as per standard design : With 20 x 20 mm square or round bar

Supplying and fixing C.I. cover with frame for manholes: 500 mm dia C. I. Cover (medium duty) the weight of the cover to be not less than 58 kg.

Supplying and stacking of good earth at site including royalty and carriage upto 1 km. (earth measured in stacks will be reduced by 20% for payment).

Spreading of sludge, dung manure or/and good earth in required thickness (cost of sludge, dung manure or/and good earth to be paid separately).

Filling mixture of earth & sludge or manure in the desired proportion in trenches flooding with water and leveling (cost of supplying earth and sludge of manure and mixing excluded).

Making lawns including ploughing and breaking of clod, removal of rubbish, dressing and supplying doobs grass roots and planting at 15 cm apart, including supplying and spreading of farm yard manure at rate of 0.18 cum per 100 sqm. as per MORTH Specification 307

Maintenance of lawns or Turfing of slopes(rough grassing) for a period of one year including watering etc. as per MORTH Specification 307

Rough dressing the trenched ground including breaking clods.

1) Grassing with “doob” grass including watering and maintenance of the lawn for 30 days or more till the grass forms of thick lawn free from weeds and fit for moving, including supplying good earth if needed. ( Cost of “doob” grass not included ) 3) In rows 5 cm apart in either direction

Providing and laying Grey or Multi Coloured Basant Beton Grass Pavers Beach Pebble of size 500x300x80mm thick size as mentioned in drawing, layed on well compacted , levelled surface, 50mm thick coarse sand bed, filling the joints with coarse sand.Compaction, levelling, etc complete as directed by Engineer Incharge.

Providing And laying Grey or Multi Coloured Pimple Finish Flag Stone paving tile 65mm thick in flooring, Basant betons make or equivalent over 50mm thickness of cement mortar 1:6 (1 cement : 6 coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the paving tile including rubbing and polishing complete.

Street Light Panel: Supply, Installation, testing and commissioning of LT panel IP- 67 outdoor type,floor mounted Panel, shall be suitable for 415 V, 3 phase, 4 wire, 50Hz Supply system. With 3 phase energy meter and 63A TPN MCB as incommer and 11 nos of 16 A TPN MCB as outgoing with 3 numbers of microcontoller based 25 A programmable digital Almac timer. As shown in SLD.

Outdoor LV Main Switchboard for 400 KVA Transformer centre made of CRCA sheet with PU painted and complete with all accesorries and HDGI mounting channels

4-way, TP&N, 3 phase, 415V, 2 nos. of 315 Amps incomings, 4 nos. of 200Amps outgoing rating type suitable for outdoor installation made out of CRCA sheet with PU painted complete with all accessories and HDGI mounting channels. (4 way Feeder Pillar)

3 phase and N, 415V, 200A MCCB incoming: 3 TPN MCCBs and fitted with 12 nos. 63 Amps SP MCBs, 24 nos 32 Amps SP MCBs, 12 nos 16 Amps SP MCBs Distribution Service Pillar suitable for outdoor installation made out of of CRCA sheet with PU painted complete with all accessories and HDGI mounting channels. (48 way Distribution service Pillar)

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 4 Core 6 sq.mm

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 4 Core 10 sq.mm

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 Core 6 sq.mm

Supply of 3 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 Core 2.5 sq.mm

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 1/2 Core 35 sq.mm

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 1/2 Core 150 sq.mm

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 1/2 Core 300 sq.mm

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (3) 4 x 6 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (4) 4 x 10 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (1) 3 x 1.5/2.5 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (3) 3 x 6 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (2) 3 1/2 x 35 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (7) 3 1/2 x 150 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (11) 3 1/2 x 300 Sq. mm.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge, sand cushioning with screened sand bed of 20mm thick, protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (b) In rocky strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run (the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (b) In rocky strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 120 sq.mm but not exceeding 400 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable)and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (b) In rocky strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm in the existing RCC/HUME/STONEWARE Metal pipe, etc. complete as required

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 400 sq.mm in the existing RCC/HUME/STONEWARE Metal pipe, etc. complete as required

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark,of approved brands, including accessories and providing masonry enclosure with CI/RCC cover having locking /lifting arrangement and watering pipe etc. with charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c) Charcoal/salt as per specs ( paid seperately). d) Refilling the pit of size 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe. g) watering arrangement (a) In soily strata

Providing and fixing 6 SWG dia GI wire on surface or in recess for loop arthing along with existing surface/ recessed conduit/ submain wiring/ cable as required

Providing and fixing 25 mm x 5 mm GI strip on surface or in recess for coneections etc. as required

Supply & erection of Decorative 3 meter cast iron pole, Primered and PU painted factory Finished. The column must have a hinged flush door at the bottom with proper strengthening to the cutout of the door opening. A junction/ looping box with 32 Amps heavy duty connector shall be built in to the pole and with provision of SP MCB, provided with a base plate and one set (4 Nos.) of SS J-bolts, and including 40 watts LED luminair of IP65 with die cast aluminium housing of IK 08 of reputed make of Dwarka DLR-1-30-5+VGL-U-001or equivalent subjected to approval of sample by engineer in charge and with other required accesories. Exclusive of MCB and 3c 2.5 sq mm wire from MCB to Fitting

Supply and erection of 8 Mtrs Octoganal Pappeared H.D.G.I pole made out of 4 m.m. thick plate and heavy provision for cable entry, having weight not less than 97kg. 4 Nos of J type M24x 750mm long foundation bolts of grade EN 8 as specified by GED. Along with suitable arm and LED fixture of inled make specified by GED of 80 W

Supplying installation testing comissioning of LED floodlight of 30 W, 230V, outdoor IP65 type, 3000 K with required accessories of Jaquar, wipro, crompton make or equivalet approved by Engineer - in - Charge complete as required.

Supplying installation testing comissioning of LED floodlight of 50 W, 230V, outdoor IP65 type, 3000 K with required accessories of Jaquar, wipro, crompton make or equivalet approved by Engineer - in - Charge complete as required.

Supplying installation testing comissioning of LED floodlight of 60 W, 230V, outdoor IP65 type, 3000 K with required accessories of Jaquar, wipro, crompton make or equivalet approved by Engineer - in - Charge complete as required.

Supplying installation testing comissioning of Inground spike lights LED lights of 15 W, 230V, outdoor IP65 type, 3000 K, Die cast aluminium housing, 304 stainless steel ring transperent, tempered glass diffuser with required accessories of Jaquarmake or equivalet approved by Engineer - in - Charge complete as required including driver.

Supplying installation testing comissioning of LED strip lights of 75 W, outdoor IP65 type, 3000 K, of length 5 mtrs, including driver of suitable wattage Jaquarmake or equivalet approved by Engineer - in - Charge complete as required with driver.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required. (c) Group C -- with Cat A Modular Accessories

Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor single core cable in the independent surface/ recessed FRLS PVC conduit of appropriate size as required. (b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor single core cable in the independent surface/ recessed FRLS PVC conduit of appropriate size as required. (c) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit)

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/16 A modular switch connection painting etc. as required. (a) Cat A

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 15/16 A and 5/6 A modular socket outlet modular socket outlet and 15/16 A modular switch connection painting etc. as required. (a) Cat A

Supplying and fixing modular blanking plate on the existing modular plate switch box excluding modular plate etc. as required (a) Cat A

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required Cat A

Supply and erecting fan hook box ( 100 mm diameter or equivalent square size, 75mm deep) fabricated out of 16 SWG sheet steel with 10 m round bar hook bounded to RCC steel upto 50 mm length protruding on each side of the box, including painting with 2 coats of red oxide, complete as required.

Supply and erecting of 12 inch (300 mm sweep) exhaust fan with double ball bearings, 1400 rpm, complete with all accessories. CAT A

Supply and erecting of 56 inch ( 1400mm sweep) ceiling fan, double ball bearing type, , complete with all accessories. (a) Cat A

Supplying, installation, testing and comissioining of LED BUlkhead fixtures with 10 W, 230V Intergral type including all the required accessories of Wipro, crompton, Bajaj, havels make or equivalet approved by Engineer - in - Charge complete as required.

Supply, Erection,Testing & Commissioning of 24 W LED TubeLight luminaire.with required Driver and other accessories of Wipro, crompton, Bajaj, havels or equivalent make approved by Engineer - in - Charge complete as required.

Supply, Erection, Testing & Commissioning of LED down light (surface or recessed) Round/ square integrated with 10W LED WW luminaire.with required Driver of K-Lite, cropton, bajaj, havels, wipro make or equivalet approved by Engineer - in - Charge complete as required.

Supplying and fixing following way SPN sheet steel MCB distribution board 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) (c) 12 way single door Cat A

Supplying and fixing following way TPN sheet steel, double door, Verticle type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/ RCCB/ Isolator)interconnection between incomer MCB and busbars of following ways (but without MCBs as required) (b) 12 way (8+24), double door, Vertical type, Cat A

Providing and fixing following rating and breaking capacity fixed type/adjustible 3 pole MCCB inside the existing cubicle panel board including drilling holes in cubicle panel making connections etc as required (j) 250 A Adjustible 35/40 KA, CAT B

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (a) SP, Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (e) TPN, Cat A

Supplying and fixing SP blanking plate in the existing MCB DB complete as required

Supply and erecting meter box suitable for three phase energy meter and incoming SP/DP MCB, fabricated out of 16 SWG sheet steel, powder coated, complete as required and conforming to the requirements of Goa Electricity Deaprtment.

Supply, installation, testing and commissioning of electronic type single phase energy meter (KWh), ISI marked, in polycarbonate or sgheet steel body ( base mounting type) with counter display/LCD display, with ELT, in Class 1.0, 50 Hz, 240 V. AC duly tested by MRT along with Test Certificates, complete as required of following capacity of make L & T only. (b) 10 to 40 A

Supply, installation, testing and commissioning of electronic type three phase energy meter (KWh), 4 wire, ISI marked, in polycarbonate or sgheet steel body ( base mounting type) with counter display/LCD display, with ELT, in Class 1.0, 50 Hz, 240 V. AC duly tested by MRT along with Test Certificates, complete as required of following capacity of make L & T only. (b) 10 to 40 A

Supply and fixing of cable route marker 15 cms diameter of GI plate 6mm thick with inscription theron bolted or welded to 25mm x 25mmx 5mm angle iron 60 cms long and fixing the same in ground with PCC etc complete as required.

Supply of cable route marker 20 cms diameter of GI plate 6mm thick with inscription theron bolted or welded to 25mm x 25mmx 5mm angle iron 60 cms long and fixing the same in ground with PCC etc complete as required. For HT cable.

Providing & fixing G.I. pipes complete with G.I. fittings including trenching & re-filling etc. (external work). 50 mm nominal bore

Providing & fixing G.I. pipes complete with G.I. fittings including trenching & re-filling etc. (external work). 80 mm nominal bore

Supplying, of HDPE pipes at store or site of work including loading unloading, stacking, transit insurance etc. complete bearing ISI mark & conforming to IS:4984-1995 & made from PE 100 resin Class IV (6kg/cm2). 63mm

Supplying, of HDPE pipes at store or site of work including loading unloading, stacking, transit insurance etc. complete bearing ISI mark & conforming to IS:4984-1995 & made from PE 100 resin Class IV (6kg/cm2). 110mm

Conveying carefully from stack at site, 250m from both sides rolling and lowering in trenches, laying true to line and level and perfect linking for joints for P.V.C / H.D.P.E complete in all respects as per the direction of the engineer in-charge 63 mm OD

Conveying carefully from stack at site, 250m from both sides rolling and lowering in trenches, laying true to line and level and perfect linking for joints for P.V.C / H.D.P.E complete in all respects as per the direction of the engineer in-charge 110 mm OD

Cable Duct Across the Road (Providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road (new construction), extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of RCC pipe as per IRC:98-1997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC: 98 - 1997 and approved drawings.) Single Row for one utility service

Supply installation testing and comissioining of wall mounted split AC of 2 TR, 3 star, having inverter based compressor technology with power rating of 3 star, including required copper and drain pipping, communication cable, refrigerant gas, outdoor unit with stand, stabilizer and required accesories of make Daikin, Blue star or equivalent subjected to approval from engineer incharge

Supply of 62.5 KVA 3Phase Generator with Advanced Digital Controller (ADC2600) with amf logic panel, and 12V 6A battery Charger * Engine: Tata-Cummins 497 TC 74, TCIC *Alternator: Meccalte/CG. Canopy: having 3 door system only [1xAttachable & De attachable door( engine side) & 2xHinge type openable doors] with 3 YEARS COMPREHENSIVE WARRANTY AND HASSLE-FREE MAINTENANCE MAKE:- KOHLER/ STERLING/ CATAPILLAR

Supply & installtion of indor type wall mounted or floor mounted fabricated, painted, DG contorller controlled 100Ats Auto changeover make socomech with handel, with completed internal wiring,studs

BAGKIYA CONSTRUCTIONS PVT LTD (BID ID -45270)

R. B. S. Candiaparcar (BID ID -44924)