Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹38.9 LAccepted-AOC P 45 JOGENDRA GARDEN KOLKATA 700078 | KOLKATA | WEST BENGAL | 700078 | L1 | Accepted-AOC Being lowest bidder and reasonable | |
| 2 | L2₹43.9 L+₹4.7 L (12.1%)Rejected-Finance ROOM NO B 111 PART III GANESH MURTINAGAR CAPT PRAKASH PETHE MARG CUFFEPRADE CALABA MUMBAI 400 005 | MUMBAI | MAHARASHTRA | 400005 | L2 | Rejected-Finance Other than lowest | |
| 3 | L3₹45.0 L+₹5.8 L (14.7%)Rejected-Finance 38 BAGUIATI ROAD KOLKATA 700059 | 24 PARAGANAS NORTH | WEST BENGAL | 700059 | L3 | Rejected-Finance Other than lowest |
Tender Value
₹36 L
EMD Value
₹72,000
Closing Date
26 Nov 2022, 10:00 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE (FW) Kolkata
D9 Commissariat Road Hastings Kolkata 700022
ADDN ALTN OF BLDG NO F 05 OF ECSR PROVN OF PARKING SHED AT ECPU AND VECTORIA GATE PROVN OF CONNECTED DRAIN AND ALLIED WKS AT P O8 TUNNEL AND COMMERCIAL SINK AT EC OFFERS MESS UNDER GE (FW) KOLKATA
2022_MES_547426_3
8879/FW/E8
Open Tender
Civil Works
Item Rate
180 days
GE (FW) Kolkata
Ref tender documents
7 documents required · 7 mandatory
₹500
GE (FW) Kolkata
₹72,000
13 Jan 2023
12 Nov 2022
28 Nov 2022
12 Nov 2022
26 Nov 2022
12 Nov 2022
Amount
SCHEDULA 'A' PART-I (B/R PORTION)
Excavating in over areas n exc 1.5 m deep and getting out in soft/loose soil complete all as specified and directed.
Excavation in post holes each not exc 0.5 cum getting out returning filling in and removing earth or broken rubble mixed with earth around in layers not exc 25 cm watering and removing surplus soil to a distance not exc 50m and making good surface as in soft /loose soil complete all as specified and directed.
Surface Excavation not exc 30 Cm deep and averaging 15 Cm deep and getting out in soft/loose soils, complete all as specified and as directed.
Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.
Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed.
Removing excavated materials not exc 50 m and depositing where directed at a level not exc 1.50 m above the starting point complete all as Specified and as directed.
Dismantling AC corrugated roof sheets as in roof coverings including AC ridge complete all as specified and as directed.
Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.
Demolition of brick work built in cement mortar including all quoins, arches, pillars etc all as specified and as directed by the Engineer-in-Charge.
Taking down cement plaster on brick or concrete surfaces incl racking out joints, hacking for key, scrubbing down with water etc. all as specified and directed.
M & L for hardcore of gauge not exc 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to true surface with broken stones complete all as specified and directed.
M&L for PCC (1:4:8) type D2, by using 40 mm graded stone aggregate as in foundations, fillings and mass-concrete, complete all as specified and directed.
M & L for plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregates as in foundation filling, fixing of post holes, support to flag pipe and mass concrete complete all as specified and directed.
M & L for plain cement concrete (1:3:6) type C1 using 20 mm graded stone aggregates as in surface channels, benching and drains, etc., complete all as specified and directed.
M&L for plain cement concrete (1:2:4) type B2 (using 40 mm graded stone aggregates) in foundation filling and mass concrete complete all as specified and directed.
M&L for M 20 noninal mix PCC 1:1½:3, type A1 (using 20mm graded stone aggregate) as in pavings etc., complete all as specified and as directed.
M&L Brick Work with fly-ash Bricks (with Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.
M&L Brick Work with fly-ash Bricks Half-Brick thick, Old Size, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.
M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished rendering surfaces even and smooth without using extra cement complete all as specified and directed.
M&L for rendering 15 mm thick built in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even & smooth (without using extra cement) and mixed with water proofing compound as per manufacturer's instruction complete all as specified and directed. (NOTE : Water proofing compound shall be measured and paid seperately).
M&L 5mm thick cement plaster on ceiling surfaces finishing even and smooth without using extra cement in cement mortar (1:3) including necessary scaffolding complete all as specified and directed.
Supply only liquid water proofing compound all as specified and as directed.
M&L for glazed coloured ceramic tiles in vertical surface 300 X 450 X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles, laid over and including 10mm thick screed bed in cement mortar 1:3 complete all as specified and directed.
S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof complete all as specified and directed.
All as per Item No. 1.24 above, but 0.50 mm thick coloured plain galvalume sheet as in ridge/valley gutter of roof.
S&F for 2nd class hardwood, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, moulded or chamfered, put together with glue, pinned at joints complete all as directed.
S&F Factory made 35mm thick with 2nd class hard wood, rail and style factory made plain framed panelled shutter(two panel) with lock, rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per IS:1003(Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.
S&F 35mm thick Factory made 2nd class hard wood glazed & skeleton shutters, open rebated and prepared to receive glass, gauge etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc, size of members of shutters as specified in SSR Part-I section 8, clause 8.20(a) complete all as specified and directed.
S&F Butt hinges, medium weight, Stainless steel, size 150 mm complete all as specified and directed.
S&F Butt hinges, medium weight, Stainless steel, size 75 mm complete all as specified and directed.
S&F Butt hinges, medium weight, Stainless steel, size 100 mm complete all as specified and directed.
S&F for Aluminium anodised barrel tower bolts of extruded sections, 150 mm long complete all as specified and directed.
S&F for Aluminium anodised barrel tower bolts of extruded sections, 200 mm long complete all as specified and directed.
S&F 300mm aluminium, anodised sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy all as directed complete all as specified and directed.
S&F 300mm aluminium, anodised sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, as in repairs, all as directed complete all as specified and directed.
S&F Extruded aluminium alloy handles, fabricated type, anodised, 150 mm complete all as specified and directed.
S&F stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.
S&F stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, in repairs, complete all as specified and directed.
Hacking out old broken glass (any thickness and size or quality) from wooden frames glazed with putty or fixed with beads complete all as specified and directed.
Hacking out old broken glass (any thickness and size or quality) from metal frames glazed with putty or fixed with beads complete all as specified and directed.
S&F 4mm thick ordinary quality plain sheet glass and glazing in square n.exc. 0.5 Sqm in each pane complete all as specified and directed.
S&F 4mm thick ordinary quality frosted sheet glass and glazing in square n.exc. 0.5 Sqm in each pane complete all as specified and directed.
M&L mild steel work in tubular trusses including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS-1161:2014 grade St-240 complete all as specified and directed. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete)
Supply and fixing Rolled mild steel in joist, channel, angle, or tee section fixed independently, upto a height of 6 metre from each floor level (cut to ordinary length i.e. within 20mm of the length indicated) of FE-410- W(Gde-E-250) quality-B including using iron props and steel plates to existing RCC overhead members like beams, slabs etc., so as to ensure safety of existing structure and floor during repairing works complete all as specified and as directed.
M&L for applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.
M&L for applying two coats of synthetic enamel paint over a coat of pink primer on old wood or wood based surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.
M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.
M&L Preparing new Steel or Iron Surfaces of any description, not exc 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.
M&L for applying evenly a coat of blown bitumen @ 1.50 Kg/Sqm and blinding with clean dry sand @ 0.05 Cum per Sqm, complete all as specified and as directed.
M&l for preparation of old painted steel surfaces exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.
M&L for applying one coat of weather proof exterior emulsion paint to old decorated surfaces of wall including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss, efflorescent salts, trading oil and greasy spots) complete all as specified and directed by Engineer -in-Charge.
M&L for preparation of new plastered surfaces of walls and applying 2 mm thick wall putty over plastered surfaces, finishing surfaces even and smoooth and applying two coats of acrylic distemper over a coat of alkali resistant primer as per manufacturer's instructions complete all as specified and directed.
Supply, hoisting and fixing rotational moulded polyethylene water storage tank (cylindrical vertical type with closed top) of capacity 1000 Litres, multi-layered (ISI marked), with GI tank nipple & cover, hoisted and fixed in position all as specified in SSR Part-I incl dismantling of existing unsv tank and writing CA No & Year with synthetic enamel paint complete all as specified and directed.
S&F 20 mm bore Ball brass valves, high pressure, with HDPE float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. (MAKE : PRAYAG, Cat No. B-152 or equivalent model in JEXON / POLYTUF / SHAKTI)
S&F White PVC Flushing Cistern 10 Litre capacity, Low Level Valve Less, Syphonic Action type with Inlet, Ball Valve, Float, flush pipe and Handle including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 and fixed complete all as specified and directed. (MAKE : PARRYWARE, Model : Slim line Economy / HINDWARE, Model : Sleek Plus / CERA, Model : Corona / PRAYAG, Model: SMART or equivalent model in COMMANDER )
S&F False ceiling with 'E' board "Classic", reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on powder coated aluminium snap grid to support the boards/files with powder coated aluminium anodised main 'T' section 36mm x 25mm x 1.40mm, cross tee 23.50mm x 23.50mm x 1.40mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides, fixed to ceiling with hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and as directed. (NOTE: Quoted rate shall be deemed to be inclusive of the cost of ceiling board)
Supply and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. (NOTE: Cost of sand cushioning is deemed to be included in the quoted rates)
S&F in position, at or near ground level, factory made precast cement concrete kerb stone blocks, in M-25 grade cement concrete, fixed to the required line, level and curvature, jointed in cement mortar 1:3, including making joints with or without grooves (thickness of joints, except at sharp curves shall not be more than 5 mm) including making drainage opening wherever required complete all as specified and directed.
M&L for plain cement concrete (1:2:4) type B1 usi ng 20 mm graded aggregates in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones , bed plates, kerbs, water troughs and the like includinguding weathering, slightly rounded or chamfered angles and throating including formwork complete all as specified and directed.
M&L for 100mm thick PCC type D2 (1:4:8) using 40 mm graded stone aggregate as in sub base concrete, finished even and rough to receive the top layer, complete all as specified and directed.
M & L for Providing precast cement concrete Type B1 1:2:4 (20mm graded aggregate) Set in cement mortar 1:4 in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including necessary forms, moulds, etc complete all as specified and as directed.
M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc completed all as specified and directed.
M&L Mild steel round bars 10 mm dia and over, cut to length, bent to shape required including crank-ing, bending and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm, complete all as specified and as directed.
S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, confirming to FE-410-W (Gde E-250) complete all as specified and directed.
S&F commercial kitchen sink made out of stainless steel sheet SS 304, 18 gauge of overall size 2286 mm x 838 mm x 0.914 mm with legs and bowl size 2134 mm x 686 mm x 203 mm depth, glossy finish, with plugs, washers, CP waste couplings, 32 mm dia PVC waste pipes (of suitable size), connecting union etc., (Make & Model; As per sample, as approved by GE) complete all as specified and as directed.
S&F commercial kitchen sink made out of stainless steel sheet SS 304, 18 gauge of overall size 1524 mm x 610 mm x 0.914 mm with legs and bowl size 1327 mm x 450 mm x 203 mm depth, glossy finish, with plugs, washers, CP waste couplings, 32 mm dia PVC waste pipes (of suitable size), connecting union etc., (Make & Model; As per sample, as approved by GE) complete all as specified and as directed.
S&F commercial chimney made out of stainless steel sheet SS 304, 18 gauge for kitchen of overall size 1524 mm x 1524 mm and length 3048 mm with with all accessories, (Make & Model; As per sample, as approved by GE) complete all as specified and as directed.
SCHEDULE 'A PART-II (ELECTRICAL WORKS)
Taking down copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceilling roses, pendants, regulators, sockets etc excluding light fitting for taking credit removing from site and making good disturbed surface of walls, floors etc.complete all as specified and directed.
Materials and Labour for concealed type point wiring with 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC conduit complete with all fittings and accessories, fixed to walls/ceiling, including mild steel terminal boxes 1.25 mm thick conforming to IS-5133 (Part-I) with 3.0 mm thick plastic laminated sheet top cover (ISI Marked) for mounting switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly, for one light point /bell point/ ceiling fan/exhaust fan point controlled by one way switch complete all as specified and directed. (NOTES: - (i) Where tube light fitting is to be fitted/suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Cost of cutting chases for concealed wiring shall be deemed to be inclusive in the quoted rates. No claim in this regard shall be entertained at a later stage)
All as per item No. 2.02 above but for one 5 amps switch socket outlet on same board controlled by another switch, complete all as specified and directed (concealed type point wiring with terminal box).
All as per item No. 2.02 above but for one 5 amps switch socket combination on independent board, complete all as specified and directed (concealed type point wiring with terminal box).
All as per item No. 2.02 above but using 2.5 sqmm single core multi stranded copper conductor FRLS PVC insulated and unsheathed, cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with and incl 2.5 sqmm green FRLS PVC insulated and unsheathed, copper conductor as continuous earth wire with lugs complete all as specified and directed (concealed type point wiring with terminal box).
S&F Switch piano, flush type single pole, one way 5 Amp complete all as specified and directed.
S&F Socket outlet 2 in 1, 3 pin, 5A complete all as specified and directed.
S&F Switch socket combination 2 in 1, 5 A flush type complete all as specified and directed.
S&F Switch socket combination multipurpose 2 in 1, 15/16 A flush type complete all as specified and directed.
S&F new Ceiling rose, surface type, three terminals, PVC/polycarbonate complete all ass pecified and directed.
S&F electronic type stepped speed regulator, 100 watts, AC 230 Volts for ceiling fan, complete all as specified and directed.
S&F sub main wiring with 2 runs of single core FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm alongwith one run of FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm as earth continuity conductor drawn through and incl PVC conduit of suitable size complete all as specified and directed. (NOTE : Three runs of single core 4.0 sqmm cable & one run of PVC conduit shall be measured as one unit)
S&F surface mounted LED luminaire, 1 X 20 Watt in aluminium housing, operating voltage 180-270 V, with acrylic/polycarbonate difuser & integrated constant current electronic driver complete with all other accessories internally prewired and including connecting up with three core flexible copper wire of suitable size complete all as specified and directed. complying with the following specifications:- (a) minimum efficacy 110 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation
All as per Item No.2.15 above, but of 1 X 9/10 Watt capacity in polycarbonate housing with lumen output not less than 105 lumen per watt
S&F exhaust fan 300 mm sweep, 900 RPM, heavy duty, AC Single Phase 230/240 volts, made with sturdy Engineering plastic body, louvers complete with all accessories and connecting up with and including twin core twisted flexible copper conductor cable of size 1.5 sqmm (nominal area) from ceiling rose to fan complete all as spcified and directed. (MAKE : HAVELLS, Model: Turbojet SP / CROMPTON, Model: EXHD300-6-1 / USHA, Model: Turbo Heavy Duty or equivalent model in BAJAJ / ORIENT) NOTE: Old fan, if any taken down, shall be deposited by contractor in MES storeyard.
S&F MCB DB TPN 4 way (8+12), IP 43 protection, double door (premium quality), 415 volts, with 100 Amps copper bus bar for each phase complete all as specified and directed. (MAKE : L&T, Cat No. DBTPN004DD / LEGRAND, Cat No: 507670 / SCHNEIDER, Cat No. A9HTND04 / ABB, Cat No: E-SHDB M4 / PANASONIC, Cat No: BQS 304H / HAGER, Cat No: VYT04DH)
S&F MCB DB SPN 8 way , IP 43 protection, Double Door (Premium Quality), with 100 Amps rated copper bus bar, Single Pole & Neutral, complete all as specified and directed. (MAKE : L&T, Cat No. DBSPN008DD / LEGRAND, Cat No: 507611 /ABB, Cat No. E-SHC M 8 / SCHNEIDER, Cat No. A9HSND08 / HAGER, Cat No: VYS08D)
S&F MCB DB SPN 4 way, IP 43 protection, double door (Premium Quality), 240 volts, with 100 Amps copper Bus Bar complete all as specified and directed. (MAKE : L&T, Cat No. DBSPN004DD / LEGRAND, Cat No: 507610 / ABB, Cat No. E-SHC M4 / SCHNEIDER, Cat No. NBKRENSNDD04 / HAGER, Cat No: VYS04D)
S&F MCB (premium quality), 'C' series, TPN, 415 volts, 63 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)
S&F MCB (premium quality), 'C' series, SPN, 32 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)
S&F MCB (Premium Quality), 'C' series, single pole, 6 to 32 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)
S&F single pole enclosure with two pin and earth plug and socket complete with one MCB SP 20 Amps, 'C' Curve, 10 KA including all accesories complete all as specified and directed. (MAKE OF ENCLOSURE: LEGRAND, Cat No. 5078 10 / L&T, Cat No. DBMPS120SD / SCHNEIDER, Cat No: A9HMS220 / ABB, Cat No. NSYN8690SGKSP20 / C&S, Cat No: CSDBPSSPN020 / BCH, Cat No: BCHPSDBSPN20 / HPL, Cat No: MDBSP20 / HAGER, Cat No: VYA220Cor equivalent model in Havells / Indo Asian ) (NOTE : Enclosure & MCB shall be same manufacturer. Cost of MCB is deemed to be included in the quoted rate)
Supply, installation, testing and commissioning of heater water storage type electric geyser (vertical cylindrical type) 25 ltrs capacity with BEE 5 star rating (min) and ABS body, glass lined/titanium enamel coated inner tank incl fixing arrangement with providing incl suitable capacity flexible cable 3 core with 3 Pin plug top with indicator of 16 Amp complete all as specified and directed. (Make: RACOLD, Model - CDR DLX / AO SMITH, Model- HSE-VAS / Havells, Model: Monza Dx / BAJAJ, Model: CALDIA)
S&F in repairs LED Street Light/Bldg Security light fitting, 35 Watt, 240 Volts, in pressure die cast aluminium housing with lens and toughened glass cover with integrated constant current electronic driver, having ingress protection of IP 66 and impact resistace of IK 07 complete all as specified and directed and complying with the following specifications:-. (a) minimum efficacy 105 lumen/watt (b) CRI not less than 70, (c) THD < 10% (c) having in built short circuit and surge protection upto 4 kV (d) colour temperature not less than 5700 degree K (e) life not less than 50,000 hours of operation (f) Power factor > 0.95 (NOTES: (1) List of approved makes has been provided in particular specifications. Contractor shall ensure that luminaire provided comply with the aforesaid specifications. No claim shall be entertained during currency of work.. (2) Quoted rate is deemed to be inclusive of dismantling of existing bracket. (3) Wire for electric connection of new fitting and new GI pipe bracket shall be measured & paid separately.
S&F GI tubing 32/40 mm bore, light grade (Approx 1.20m long) bent to the required shape, fixed along poles/walls for street lights/security lights, fixed with 32x6mm Flat Iron clamps - 2 Sets, suitable nuts & bolts, washers, for fixing street light fittings etc complete all as specified and directed.
M&L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanized steel earth wire 4 mm dia (upto 7.5 metres) by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 45 cm x 45 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 40 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing and dismantling of existing unsv earthing complete all as shown in Figure 15A of IS 3043 :1987, complete all as specified and directed.
M/S SRINIVASA CONSTRUCTION
MODERN AGENCY
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .