General Repair with Replacement of Damaged Parts of Vehicles Backhoe Loader JCB 2DX and TATA - 709

Amount

Repair of the Loader assembly of of Backhoe Loader JCB 2DX by way of removing all the tooth from the Loader and p/f of M.S. Sheet 20 mm thick along length of loader, plough bolt (C7600565) - 16 Nos., Hexagon Nut (C9100031) - 16 Nos . The job also includes piercing of holes in MS sheet by gas welding as per the size of plough bolt. The job also includes nominal hardening and facing of loader along the length of M.S sheet for protection of Loader assembly. The complete job includes cost of material along with carriage, labour charges, hire charges of tool and tackles

Providing and Fitting of Loader Jack Seals – 04 Nos of of Backhoe Loader JCB 2DX by way of dismantling the old damaged and worn out jack seals and replacement with the new jack seals of the same specifications. The complete job includes cost of material along with carriage, labour charges, hire charges of tool and tackles.

Repairs to radiator of Backhoe Loader JCB 2DX by flushing upper and lower tanks with caustic soda, soldering its leaking tubes, straightening the fins, replacement of leaking hoses, hose clamps and then reassembling after checking leakage. Also repairs to the fuel system by servicing to fuel tank by cutting and then welding, replacement of fuel pipes, banjo washers, banjo bolts, injector pipes with new ones, calibration of injectors, setting of their pressure on machine. Complete job including cost of material and labour charges.

Labour charges for repairs to operator seat of Backhoe Loader JCB 2DX by way of using iron G.I sheets and p/f of rexgine, cushion cover etc. including stitching charges also and repairs to back by way of welding and fitting of nuts and bolts also, the job includes cost of angle iron.

Periodic servicing of the Backhoe Loader JCB 2DX by way of Providing and Fitting of Air Filter set (Primary/secondary) – 01no., M oil Filter – 01no, Hydraulic filter – 01 set, Spin Fuel Filter – 01 Set. Job also includes Providing and Filling of M-oil – 15 Ltrs., Gear Oil – 20 Ltrs., Hydraulic oil – 60 Ltrs., Transmission oil – 20 Ltrs., Break oil – 1 Ltrs., Coolant – 10 ltrs. Replacement r of fuel pipe – 01 No. The job includes the cost of the rubber material, nuts and bolts with washers and labour charges for the complete work

P/F of Heavy duty Plane Mirror left side of required size – 01 No., Pressure pipe 0300 series – climatised MWP – 350BAR, P/f of stop wire choke assembly – 01 No., p/f of new horn – 01 No., P/f of new wiper -01 set., P/f of new door hooks – 08 No., P/f of new front axel bush – 01 set., P/f of lever – 01 set. The job includes the cost of the rubber material, nuts and bolts with washers and labour charges for the complete work. (Backhoe Loader JCB 2DX)

Periodic servicing of the Sky Lift Machine TATA-709 JK20B – 1418 by way of Providing and Fitting of Diesel Filter set– 01 set., M oil Filter – 01no, Hydraulic filter – 01 set. Job also includes Providing and Filling of M-oil – 15 Ltrs., Gear Oil – 20 Ltrs., Hydraulic oil – 120 Ltrs., Axle oil – 20 Ltrs., etc. The job includes the cost of the rubber material, nuts and bolts with washers and labour charges for the complete work

Repairs to Self Starter, Dynamo and wiring of Sky Lift Machine TATA-709 JK20B – 1418 by way of dismantling of self starter, dynamo and worn out wiring of DRR. P/F of Self Armature, Self Carbon bushes, Clutch disks, Contact point and defective rods. P/F of Dynamo Armature, Bearing, Carbon bushes. Replacement of worn out wiring, battery leads etc. P/F of Voltage regulator, Ammeter starting switch with key, L.T. wire as per requirement of job. Complete Job includes assembling of unit, testing, cost of labour and allied material

Repair to tie rod and king pin assembly of Sky Lift Machine TATA-709 JK20B – 1418 by way of dismantling and extraction of worn out parts and replacement by way of P/f of new parts King pin – 02 Nos., King pin bush – 04 Nos., King pin bearings – 02 Nos., Arm bolt – 01 No., Sapcer – 02 Nos., Shims – 02 Nos., O-ring – 02 Nos., King pin lock – 02 Nos., Tie rod end (LH & RH) – 01 set, Tie rod end repair kit – 01 set, King pin repair kit – 01 No., along with alignment of wheel and checking. The job includes the cost of the rubber material, nuts and bolts with washers and labour charges for the complete work

VEE AUTO TRADERS

KANT AUTOMOBILES