ge/de-32/2020-2021

Amount

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and as directed.

Demolition of cement concrete, unreinforced, in ground floors and pavings not exceeding 15cm thickness below or above ground level, complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facings, complete all as specified and as directed.

Taking down cement plaster from brick or concrete surfaces including raking out joints, hacking for key and scrubbing down with water, complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5Sqm each and removing to store, complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5Sqm but not exceeding 4Sqm each and removing to store, complete all as specified and as directed.

Dismantling structural steel work including doors, gates but including framed trusses etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) & removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling of CI or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches of diameters upto 100mm, complete all as specified and as directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar (Internal dia of pipe in 200mm), complete all as specified and as directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar (Internal dia of pipe in 150mm), complete all as specified and as directed.

Surface excavation in soft/loose soil not exceeding 30cm deep and averaging 15cm deep and getting out, complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth : for foundation, etc or for shafts wells, cesspits, manholes etc., not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil, complete all as specified and as directed.

Returning, filling in, including spreading levelling watering and well ramming in layersn.exc 250 m thick on soft/loose soil, complete all as specified and as directed.

Removing excavated material not exceeding 50mtr and depositing where directed at a level not exceeding 1.5 m above the starting points in soils, complete all as specified and as directed.

Plain cement concrete 1:4:8, Type D-2 using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete, complete all as specified and as directed.

Plain cement concrete 1:2:4 type B-1 as in benching, coping and similar items including weathering, slightly rounded or chamfered angles and throating on top of chajjas, rails, cills etc., complete all as specified and as directed.

PCC 1:2:4 type B-1 as in roof kerb, mud stops etc., and similar items including weathering, slightly rounded or chamfered angles and throating on top of chajjas, rails, cills etc., complete all as specified and as directed.

Reinforced cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate, as in beams, lintels over 1.5mtr span, and plinth beams, etc., complete all as specified and as directed.

Plain cement concrete 1:3:6, Type C-2 using 40mm graded crushed stone aggregate as in surface channels and drains, complete all as specified and as directed.

Brick work with sub class “B” bricks straight or curved on plan exceeding 6mtr mean radius built in cement mortar 1:6 using old size bricks, complete all as specified and as directed.

Brick work with sub class “B” bricks straight or curved on plan exceeding 6mtr mean radius built in cement mortar 1:4 using old size bricks, complete all as specified and as directed.

Damp proof course to horizontal or vertical surfaces including necessary formwork, 40mm thick, in cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate), complete all as specified and as directed.

Form work to soffits and sides of beams, lintel bands and plinth beams and similar type of work, for rough finished surfaces for flat or curved surfaces of concrete complete all as specified and as directed.

18-20mm thick Granite stone slab (table rubbed and polished) in steps, shelves, and the like not less than 1Sqm (in one piece), laid over 20mm thick layer of cement mortar 1:3 after rougheniung of existing concrete surface and applying a layer of neat cement slurry @ 3Kg/Sqm including pointing in white cement 1:2 using marble dust with admixture of pigments to match with shade of stone with moulding of edges, including dismantling of old stone of any type and description, complete all as specified and as directed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail, lock on either side and gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointing together with solvent cement, supplying & fixing of frame at site, complete all as specified and as directed.

100mm size butt hinges (medium weight) colled rolled mild steel fixed with welding, complete all as specified and as directed.

Aluminium alloy handles cast type anodised of size 150mm size, complete all as specified and as directed.

Aluminium anodized 150mm size barrel tower bolt of extruded section and fixed, complete all as specified and as directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm, and fixed with tinned tacks or galvanised mild steel staples, complete all as specified and as directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending, spirally for hopping for columns, hooking ends, and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-S or Fe-410-0, complete all as specified and as directed.

TMT bars 5mm dia and over upto and including10mm dia cut to length, in stirrups and spacers including cutting and bending, hooking ends & binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Hand rails, half round or other stock section straight portion drilled and countersunk for balusters running bars, for doors, balusters, including framed work such as grills, gratings, chowkats, purlins, rafters etc including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., complete all as specified and as directed.

Mild steel framed work as in doors (as in chowkats) or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (incl steel sheets) and hanging; also fastening and fixing (quality confirming to Fe-290 (Gde-E-165), fixed in repairs, complete all as specified and as directed.

Box type Steel windows with double shutters (inside for wiremesh & out side for glass), hinges, steel handle, tower bolt and steel peg stay complete without glazing bars dovetailed or welded including a coat of red oxide after preparation of surface before fixing all as shown in drg No. TD-A sheet 1/3 to 3/3, complete all as specified and as directed.

Box type Steel ventilators with centre hung shutters inlcuding two pairs of brass cup pivot, catch spring and pulley wheel including a coat of red oxide after preparation of surface before fixing all as shown in drg No. TD-A sheet 1/3 to 3/3, complete all as specified and as directed.

Mild steel work such as angle iron post , flat iron in fencing including cutting top to required shape including welding with proper overlapping & welding MS Plate with angle iron bottom as directed, drilling holes notching for wire etc., embedded in concrete fixed vertically conforming to grade FE-290 E-165, complete all as specified and as directed.

Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates to Fe-290 (Gde E- 165), complete all as specified and as directed.

Mild steel tubular sections as in roof trusses, including special ahaped washers, etc., complete using ERW or induction butt welded tubes conforming to Fe-410-W (Gde E- 250 quality A), complete all as specified and as directed.

Pre-Painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

Pre-Painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old roofing of AC corrugated sheets, complete all as specified and as directed.

Pre-Painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall/ridge, fixed with self tapping screws, complete all as specified and as directed.

Mild steel plain galvanised sheets 1.00mm thick as in ridges, hip and valley gutters, drip and straight flashings with grade of zinc coating 275gms/Sqm, fixed with self tapping screws including brackets/fittings as required, fixed in repairs, complete all as specified and as directed.

Cleaning and clearing roof surfaces of all the rubbish by brooming, scrubbing down wih water and rendering on top of concrete roofs with 15mm thick cement mortar in 1:3. Cleaning the plastered surface after drying from dirt, mortar, dust mortar buds, algae and all other foreign matter and brushed and wiped. Apply evenly a coat of bituminous primer conforming to IS- 3384 @ 0.4Kg/Sqm. Over the primed surface apply a coat of hot blown 85/25 penetration grade bitumen conforming to IS- 702 @ 1.2 Kg/Sqm of the surface area. Privide APP modified Polymeric five layered membrane with central core 100 micron high molecular high density polyethylene film. Minimum weight of membrane will be 3.6 Kg/Sqm. APP membrane will be laid across the slope from lowest line of roof towards ridge with over laps of 75mm in length side and 100mm on the width side of membrane bonded with hot blown bitumen. Over the APP membrane apply semi hot blown 85/25 penetration grade bitumen conforming to IS- 702 @ 1.2 Kg/Sqm and blinded with fine sand in dry condition @ 0.50Kg/Sqm dusted over the bitumen coat. Provide final layer of two coats of aluminium paint over a coat of primer as per manufacturer's instructions, complete all as specified and as directed.

5mm thick solid PVC wall lining consisting of 5mm thick wood grain printed PVC Sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications, complete all as specified and as directed by Engr-in-Charge.

5mm thick PVC sheets fillets 35mm wide for wall paneling inclusive of fixing on to wall to make PVC frame as per specifications, complete all as specified and as directed by Engr-in-Charge.

50 mm thick cement concrete 1:3:6 type C-2 (using 40mm grade crushed stone aggregate) finished even and fair as in sub base, complete all as specified and as directed.

Vibro compacted Precast concrete interlocking paver blocks, factory made,any shape and size conforming to IS- 15658- 2006 of 60mm thick, M-35 Grade set, jointed in neat cement slurry and pointed flush with grey cement mixed with pigments to match colour of blocks in floors laid over 30mm thick sand cushioning, complete all as specified and as directed.

Pre-polished coloured chequered cement concrete tiles, factory made, Premium quality 300mm x 300mm x 20mm thick, set, jointed in neat cement slurry and pointed flush with grey cement mixed with pigments to match colour of blocks in floors over 15 mm thick screed bed or bedding layer in cementy mortar 1:4, complete all as specified and as directed.

75 mm thick cement concrete 1:4:8 type D-2 (using 40mm grade crushed stone aggregate) finished even and fair as in sub base, complete all as specified and as directed.

75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection including finishing the surface even and fair, complete all as specified and as directed.

Machine cut kota stone slab 18 to 20 mm thick as in flooring laid over and including cement screed base 15mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and as directed

Non skid ceramic coloured floor tiles 7-8mm thick, area of each tiles exceeding 0.11 Sqm but not exceeding 0.18Sqm or of size as approved as in floors set and jointed in neat cement slurry and pointed in white cement with pigments to match over and including the provision of 15 mm thick bedding layer in cement mortar 1:4, complete all as specified and as directed.

Non skid ceramic coloured floor tiles 7-8mm thick, area of each tiles exceeding 0.06Sqm but not exceeding 0.11Sqm or of size as approved as in floors set and jointed in neat cement slurry and pointed in white cement with pigments to match over and including the provision of 15 mm thick bedding layer in cement mortar 1:4, complete all as specified and as directed.

Glazed ceramic tiles in vertical surface 300mm x 450mm x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering in cement mortar 1:4, complete all as specified and as directed.

Rendering 15 mm thick in cement mortar 1:6 finished even and smooth without using extra cement, complete all as specified and as directed.

Rendering 15mm thick cement plastering in cement mortar 1:4 on brick/concrete surface of walls including finished even and smooth without using extra cement, complete all as specified and as directed.

Rendering 5mm thick cement plastering as in ceiling in cement mortar 1:3 on concrete surfaces including finishing surfaces even and smooth without using extra cement, complete all as specified and as directed.

Rendering 10mm thick cement plastering in cement mortar 1:3 on concrete surfaces including finishing surfaces even and smooth without using extra cement, complete all as specified and as directed.

Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings including cuttng grooves, complete all as specified and as directed by Engr-in-Charge.

Removing the loose particles, cleaning the all surfaces with brush, repair with cement & Dr Fixit Pidicrete URP putty and applying two coats of Dr Fast flax all as per manufacturer instructions of Pidilite, complete all as specified and as directed. (Note : Water proofing shall be done by authorised agent of manufacturer and a written warranty for 10 years shall be given).

Injecting grouting with cement mortar and Dr Fixit AM powder all as per manufacturer instructions, complete all as specified and as directed by Engr-in-Charge.

Preparation of newly plastered surfaces of walls and applying two coat of cement based paint over a layer of Birla white wall care putty, complete all as specified and as directed.

Preparing newly plastered surfaces of walls/ceilings and applying two coats of oil bound distemper, complete all as specified and as directed.

Preparation of newly plastered or unplastered surface of walls and applying three coats of white wash, complete all as specified and as directed.

Preparing newly plastered surfaces of walls and applying two coats of wheather shield paint, complete all as specified and as directed.

Preparation of new steel surfaces and applying two coats of synthetic enamel paint on surfaces of any description exceeding 10 cm width or girth over a coat of red oxide complete all as specified and as directed.

Sheet glass 3.00mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm.in each pane, glazed with putty or fixed with beads complete all as specified and as directed.

15mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs including taking down steel tubing and connections and cleaning for refixing or removal from site, complete all as specified and as directed.

20mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs including taking down steel tubing and connections and cleaning for refixing or removal from site, complete all as specified and as directed.

40mm bore GI tubing (medium grade) with all fittings and laid in trenches or fixed to walls and ceiling including taking down steel tubing and connections and cleaning for refixing or removal from site, complete all as specified and as directed.

50mm bore GI tubing (medium grade) with all fittings and laid in trenches or fixed to walls and ceiling including taking down steel tubing and connections and cleaning for refixing or removal from site, complete all as specified and as directed.

Gas tubing of suitable dia as per manufacturer's instructions (heavy duty) with all fittings from gas cylinders storage to cook tops in cook house, complete all as specified and as directed by Engr-in-Charge. (Note : Work shall be executed by authorised agency of Indane/Bharat Gas/HP).

Tubular towel rail 'D' type 20mm dia, chromium plated brass 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats, fixed in repairs, complete all as specified and as directed.

PVC 160mm bore (SWR) pipes double socketed, in any length with rubber ring joints, flaid in trenches or in floors, complete all as specified and as directed.

PVC (SWR) bend 160mm bore, any radius, laid in trenches, complete all as specified and as directed.

PVC (SWR) floor trap, with grating including jointing to waste pipe in solvent for 110mm bore pipe including CP grating cover with or wothout hole, fixed in repairs, complete all as specified and as directed.

Sand cast iron soil waste and vent pipes 100mm dia, in any length, with cement joints, laid in trenches/floors, fixed to walls with CI/MS holder bat clamps and conforming to IS-1729, complete all as specified and as directed.

CI bend for 100mm bore any radius, diminishing pieces or tapers (larger bore measured), fixed to walls, complete all as specified and as directed.

CI branch piece equal or unequal (double 'Ý') 100mm bore any radius, diminishing pieces or tapers (larger bore measured), fixed to walls, complete all as specified and as directed.

15mm bore bib tap chromium plated brass, Fancy type, screwed for iron pipe or for brass ferrule, fixed in repairs, complete all as specified and as directed.

Vitreous china squatting pan ‘Orissa’ pattern size 580 x 440 mm white with integral foot rests including P or S trap including provn of lime concrete bedding including connections to flushing cistern/pipe, fixed in repairs, complete all as specified and as directed.

PVC valve less syphonic action type coloured flushing cistern, low level, 10 litres capacity including flush pipe PVC connection, float valve, PVC handle/button and connections, complete all as specified and as directed.

Soap dish vitreous China white, approximate size 160x 160x90mm, fixed to plugs with chromium plated brass screws, fixed in repairs, complete all as specified and as directed.

Rotational moulded polyethene water storage tank 1000 ltr capacity hoisted and fixed in position including 20mm dia float valve and dismantling of existing tank, complete all as specified and as directed.

Stop valve cast copper alloy, screwed down high pressure with capstan head for iron pipe 20mm bore, fixed in repairs, complete all as specified and as directed.

Counter type vitreous chinaware wash hand basin (WHB) white size 550mm x 400mm complete including provision of pair of mild steel angle iron brackets of suitable size duly painted, 32 mm dia chromium plated waste coupling, PVC waste pipe and cutting for pinning in ends of brackets in wall etc., fixed in repairs, complete all as specified and as directed.

15mm bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed . (Minimum weight 90gms), fixed in repairs complete all as specified and as directed.

15mm pillar tap standard of PTMT any colour high pressure screwed for iron pipe and fixed . (Minimum weight 110gms), fixed in repairs complete all as specified and as directed.

15mm angle cock standard of PTMT any colour high pressure screwed for iron pipe and fixed . (Minimum weight 90gms), fixed in repairs complete all as specified and as directed.

PVC connection 15 mm size with CP Brass nuts 600mm long, fixed in repairs, complete all as specified and as directed.

Gun metal globe or gate valve screwed down high pressure with iron wheel head, screwed both ends for iron pipe 50mm bore, fixed in repairs, complete all as specified and as directed.

Precast cement concrete gully trap of size 300mm x 300mm x 25mm thick with cover including reinforcement and mild steel frame for cover of angle iron 25mm x 25mm x 4mm, complete all as specified and as directed by Engr-in-charge.

Cutting into existing manholes including cuttng out existing benching for connecting new drains and forming branch channel (1/2 or 3/4 section), making good to pipe in cement concrete 1:2:4 type B-1 and finished smooth and reforming benching as required for 150mm dia pipe, complete all as specified and as directed.

Cutting into existing manholes including cuttng out existing benching for connecting new drains and forming branch channel (1/2 or 3/4 section), making good to pipe in cement concrete 1:2:4 type B-1 and finished smooth and reforming benching as required for 200mm dia pipe, complete all as specified and as directed.

Cement concrete type D-2 1:4:8 (using 40 mm graded crushed stone aggregate) in bed to drain pipe 150 mm dia including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

Cement concrete type D-2 1:4:8 (using 40 mm graded crushed stone aggregate) in bed to drain pipe 200 mm dia including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

Reinforced concrete pipes NP-2 of 150mm bore, laid on concrete bed and jointed with collars in cement joints, complete all as specified and as directed.

Reinforced concrete pipes NP-2 of 200mm bore, laid on concrete bed and jointed with collars in cement joints, complete all as specified and as directed.

Precast SFRC man hole covers 75 mm thick medium duty conforming to IS-12592, complete all as specified and as directed.

Repairs to water level mecanism machine at water sump showing level including float valve, water level indicator all as per fixed at site including all required accessories and two coats of painting, complete all as specified and as directed by Engr-in-charge.

Taking down carefully old unserviceable copper/aluminium point wiring From existing conduit / batten type (light, fan, socket or power point) complete such as switches, ceiling rose, pendent holder, regulator and socket etc are to be measured seperately and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing etc complete all as specified and as directed.

Point wiring complete with 1.5 Sqmm (nominal area) FRLS, PVC insulated un-sheathed and stranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and PVC conduit fittings such as tees, bends, elbow, reducers except conduit junction box (junction box will be of MS) including FRLS, PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl Metal flush box of suitable size for fixing modular switches/sockets/fan regulator etc , with and including Modular cover plates of suitable size and making good surface as original by plastering, whitewash/colour and distemper etc complete all as specified and as directed for the following :- one light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push (Note : The cost of modular type Metal boxes and modular accessories like cover plates will be included in quoted rate.)

All as per description of Srl item No. 103 here-in-before but for one 3 pin socket outlet 5/6 Amps on same board.

All as per description of Srl item No.103 here-in-before but for power socket 15/16 Amp with cable 2.5 Sqmm for phase & neutral for earth 1.5 Sqmm.

Sub main wiring with 2 run of 4.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in to separate PVC conduit with and including 2.50 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as specified and as directed. Note :- a) The conduit and conduit accessories shall be measured and paid as one unit. b) The cost of earth wire is deemed to included in he quoted rates.

Replacement of Switch piano flush type, single pole, one way, 5/6 Amps, complete all as specified and as directed.

Replacement of socket two-in-one, 5 pin, 5/6 Amp universal type, complete all as specified and as directed.

Replacement of Switch 16 Amp,single pole one way, complete all as specified and as directed.

Replacement of socket out let 6/16 Amp, flush typecomplete all as specified and as directed.

Replacement of Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps and making good surface as original by plastering and whitewash/ colour/ distemper etc., complete all as specified and as directed.

Replacement of Wall mounting tube light fitting, 20/22 watt including making all electric connections using PVC Sheathed copper conductor flexible cable, complete all as specified and as directed.

Replacement of LED Mirror light 10/12W diffuser, driver including making all electric connections using PVC Sheathed copper conductor flexible cable, complete all as specified and as directed.

Replacement of LED security light luminaire 40 watt pressure die cast aluminium housing with heat resistance toughned glass and IP- 65 protection with and including driver/transformer and including connector, complete all as specified and as directed.

Replacement of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 08 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc and making all necessary connections, complete all as specified and as directed. (Note : The cost of removing old wooden box and making good of surface as original i.e. brick work, plastering, white washing etc is included in quoted rate.)

Replacement of MCB C Curve type, 10 kA, 10 to 32 Amp, Single Pole with over load and short circuit protection, complete all as specified and as directed.

Replacement of MCB C Curve type, 10 kA, 40 Amp Single Pole with and neutral over load and short circuit protection, complete all as specified and as directed.

LT underground cable XLPE insulated, PVC sheathed, galvanised steel strip / wire armoured, aluminium conductor, 1100 volts grade, of size 10 Sqmm 2 core suitable for earthed system laid in duct / trench / along pole / wall etc including making connection complete all as specified and as directed. (Note : 1. The cost of Al thimbles/lugs and cable gland etc is incl in quoted rate and no extra payment will be made for it. 2. The excavation, earth work, sand cushioning and brick protection etc will be measured and paid separately under respective items.)

Mechanical protection to cable using old size sub class 'B' bricks, laid flat, dry, butt jointed, laid length wise perpendicular to the axis of cable, complete all as specified and as directed.

Sand cushioning with a layer of fine sand 8 cm thick before laying the cable and 15 cm after laying the cable in trenches to cover under ground cable, complete all as specified and as directed.

Replacement of fresh air fan 300 mm sweep plastic body type incuding self closing louver and making all electric connections, complete all as specified and as directed.

Earthing complete with GI earth plate electrode 600 mm x 600mm x 6mm thick burried directly in ground not less than 2.25 mtrs below ground level, with top edge of the plate not less than 1.5 mtrs deep below normal ground level, connected to galvanised earth wire 4mm by means of bolts, nuts check nuts to earth test point including necessary PCC 1:2:4 type B-1 pit, cover frame, GI pipe 15mm dia light grade for protection of earthing lead and GI pipe 20 mm dia for watering pipe with funnel, wire mesh, salt, charcoal dust and excavation, complete all as specified and as directed.

NOTE:- For minimum fair wages ,EPF and payment to labour employed, refer Sch A Note No-14,15 and Special Condition No 5 & 21.2 of this tender. Contractor must produce all the relevent record such as payment made to labour, EPF etc at the time of payment of RARs/Final bill. No payment will be released to contrator without producing the proper record.

NOTE:- Irrespective of whatever specified elsewhere in tender documents, all the debris/waste materials produced out of above mentioned work shall be removed out of Cantonement land and disposed off at locations notified by the Delhi Cantonment Board for disposal of waste building materials within NCR area, without any extra cost to Department under own arrangement of contractors. The rates quoted by the contractors against the items catered here-in-above in the BOQ are inclusive of said provision.

aggarwal engineers contractors

P.H. construction

R. S. Associates

Simran construction Company