Loading
Loading…
Loading…
| # | Company | Amount | Status |
|---|---|---|---|
| 1 | ₹4.2 Laccepted-aoc | ₹4.2 L | accepted-aoc |
Tender Value
₹4.5 L
EMD Value
₹4,500
Closing Date
6 Apr 2026, 5:00 pmClosed
EXECUTIVE ENGINEER
IRRIGATION DIVISION NO.4, GADWAL
REPAIRS AND RESTORATION OF ESCAPE REGULATOR AT KM.65.500 FOR 2 VENTS OUT OF 6 VENTS ON RDS MAIN CANAL IN IEEJA MANDAL OF JOGULAMBA GADWAL DISTRICT
689748
T.No.11/2025-26, Date:-30.03.2026
OPEN
Fabrication and Erection of Structural Steel
JOGULAMBA GADWAL
7 documents required · 7 mandatory
₹159
₹4,500
21 Apr 2026
30 Mar 2026
31 Mar 2026
OT SLUICE GATES: Fabrication, supply, erection, testing and commissioning of Sluice Shutters consisting of skin plate, horizontal and vertical angles, stiffeners, rubber seals, clamps with all accessories for sluice shutters including cost of all materials, machinery, labour, seal fixing etc., complete as per specifications and approved drawings (without painting on mechanical cleaning surfaces which are added extra as per schedule of rates under items in this chapter and add as applicable separately)
OT SLUICE Screw Gear box, Hoist and Hoist Platform: Fabrication, supply, erection, testing and commissioning of Embedded parts consisting of supporting structure, platform etc. with all accessories for operating canal escape/ regulator gate with all accessories including cost of all materials, machinery, labour, cutting, bending, aligning, anchoring, welding, finishing etc. complete
PAINTING E.M Parts: Surface cleaning of metal surfaces by chemical cleaners and then by hand and power tool cleaners and removing dust. After cleaning,applying primary coat with one coat of Protective Mastic to athickness of 70+5 microns coats 2 coats with coal tar epoxy each coat with a DFT of 150+5 microns and total DFT of all coats including Primary coat should not be less than 350 microns with material, labour and all accessories with all leads and lifts
PAINTING OF GATES: Surface cleaning of metal surfaces by chemical cleaners and then by hand and power tool cleaners and removing dust. After cleaning,applying primary coat with one coat of Protective Mastic to athickness of 70+5 microns coats 2 coats with coal tar epoxy each coat with a DFT of 150+5 microns and total DFT of all coats including Primary coat should not be less than 350 microns with material, labour and all accessories with all leads and lifts
Painting of OT SLUICE Screw Gear box, Hoist and Hoist Platform: Surface cleaning of metal surfaces by chemical cleaners and then by hand and power tool cleaners and removing dust. After cleaning,applying primary coat with one coat of Zinc rich epoxy primer to a thickness of 40 microns ,followed by finishing coats 2 coats with coal tar epoxy with material, labour, and all accessories with all leads and lifts
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
~$CAPE REGULATOR.docx
TENDER_DOCUMENT • 0.00 MB
BOQ.xls
TENDER_DOCUMENT • 0.02 MB
ESCAPE REGULATOR.docx
TENDER_DOCUMENT • 0.25 MB
ESCAPE REGULATOR.xls
TENDER_DOCUMENT • 0.17 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .