PROVISION OF CERTAIN TECHNICAL STRUCTURES AND SERVICES AT AF STATION UTARLAI

Amount

SCHEDULE `A' PART - I is not prepriced by MES and prepriced rates indicates 0.0 under column 5 signified this fact only.(TO BE QUOTED BY THE CONTRACTOR) (Structural design of Bldgs/structure covered under this schedule are to be done by Contractor)

Provn of RCC framed structure TOWER RAMP STRUCTURE (Size 30m x 33m x 6m high) along with both side Ramp its RCC retaining wall, RCC parapet, stair case, stair hall including structural designing complete all as shown in drawings, as specified and as directed.

Provn of of Plinth (No 1, 8 & 10) (Size 11m x 15m x 5m clear high) with PQC flooring, galvalume shed including steel trusses, eathern traverse on three sides, RCC wing & retaining wall, Toe wall, Apron, dwarf wall, schedule of finish complete including structural designing complete all as shown in drawings as specified and as directed. Note: (i) Pavement beyond appron as shown on plan in front of structure shall be measured and paid separately (ii) Contractor has to quote lumpsum for 01(One Plinth) and multiply by 3 to arrive at total quoted amount of BOQ item No 3.

Provn of Plinth (No 4) (Size 5m x 10m x 5m clear high) with PQC flooring, galvalume shed including trusses, eathern traverse on three sides, RCC retaining & wing wall,Toe wall, Apron, dwarf wall schedule of finish etc. complete including structural designing all as shown in drawings as specified and as directed. Note: (i)Pavement beyond apron shown on plan in front of structure shall be measured and paid separately

Provn of Plinth (No 3) (Size 10m x 20m) with PQC flooring, eathern traverse on two sides, RCC retaining & wing wall, Apron on both side, Toe wall & dwarf wall, schedule of finish etc.complete including complete structural designing complete all as shown in drawings as specified and as directed. Note: (i)Pavement beyond apron as shown on plan in front of structure shall be measured and paid separately.

Provn of Plinth (No 11 & 12) (Size 20m x 30m) with PQC flooring, eathern traverse on three sides, RCC retaining & wing wall, VIFT on front including RCC retaining wall and traverse, Toe wall, Apron on front side, dwarf wall, schedule of finish etc complete including structural designing complete all as shown in drawings as specified and as directed. Note: (i) Pavement beyond apron as shown on plan in front of structure shall be measured and paid separately. (ii) Contractor has to quote lumpsum for 01(One Plinth) and multiply by 2 to arrive at total quoted amount of BOQ item No 6.

Provn of Plinth (No 7 & 9) (Size 20m x 10m) with PQC flooring, eathern traverse on all sides with entry, RCC retaining & wing wall, Toe wall, Apron on both side, dwarf wall ,schedule of finish etc. complete including structural designing complete all as shown in drawings as specified and as directed. Note: (i)Pavement beyond apron as shown on plan in front of structure shall be measured and paid separately. (ii) Contractor has to quote lumpsum for 01 (One Plinth) and multiply by 2 to arrive at total quoted amount of BOQ item No. 7.

Provn of RCC framed structure Parking Garages (10 nos Auxiliary Vehicle Garrage) for A Vehicles (10 bays) (Size 66.84m x 21.95m x 8m clear high) with Apron, dwarf wall including concrete flooring Schedule of finishes etc including structural designing complete all as shown in drawings as specified and as directed.

Provn of RCC framed structure Parking Garages (15 nos Auxiliary Vehicle Garrage) and Apron, dwarf wall, schedule of finish including structural designing complete all as shown in drawings as specified and as directed. Note: (i) Road shown on plan beyond apron in front of structure shall be measured and paid separately

Provn of RCC framed structure Parking Garages (2 x 10 nos) i.e 20 nos Auxiliary Vehicle Garrage) (Size 66.84m x 83.9m x 8m clear high) including Apron both sides, dwarf wall and Pavement quantity concrete flooring in between two buildings, schedule of finish complete including structural designing complete all as shown in drawings as specified and as directed.

Provn of RCC framed structure OPs Room cum Briefing Room bldg, schedule of finish including structural designing complete all as shown in drawings as specified and as directed.

Provn of RCC framed structure Guard Rest Room with Ground Crew Rest Room bldg, schedule of finish including structural designing complete all as shown in drawings as specified and as directed.

Provn of RCC framed structure Toilet Block, schedule of finish including structural designing complete all as shown in drawings as specified and as directed.

Provn of RCC framed structure POL Store with Ramp , schedule of finish including structural designing complete all as shown in drawings as specified and as directed.

Provn of RCC framed structure UWO Store cum work shop, rolliing shutter with verendah, Ramp, schedule of finish including structural designing, complete all as shown in drawings as specified and as directed.

Provn of RCC framed structure Open Parking Garages for C Vehicles ,(Size 39.2m x 6.14m) (6 bays) with Apron, schedule of finish including structural designing complete all as shown in drawings as specified and as directed. Note : (i) Contractor shall quote lumpsum for 01(One Garrage ) and multiply by 2 to arrive at total quoted amount of BOQ item No16 (6x2=12 Vechiles)

SCHEDULE `A' PART - II are not prepriced by MES and prepriced rates indicates 0.0 under column 5 signified this fact only and are TO BE QUOTED BY THE CONTRACTOR.

Provn of Plinth (No 2 & 5) (Size 15m x 20m) with PQC flooring, Toe wall, Apron on front side, dwarf wall, schedule of finish etc complete all as shown in drawings as specified and as directed. Note: (i) Pavement beyond apron as shown on plan in front of structure shall be measured and paid separately (ii) Contractor has to quote lumpsum for 01 (One Plinth) and multiply by 2 to arrive at total quoted amount of BOQ item No. 18.

Provn of Plinth (No 14) (Size 35m x 20m) with PQC flooring, Toe wall Apron on front side, dwarf wall, schedule of finish etc complete all as shown in drawings as specified and as directed. Note: (i) Pavement beyond apron as shown on plan in front of structure shall be measured and paid separately

Note to item no. 1 to 19 :- (i) If soil obtained from excavation of building/ structures is not adequate/sufficient or suitable for filling in trenches, plinth, under floor, traverse etc additional earth required shall be obtained from outside MD land without any extra cost to Govt. (ii)Below each igloos and associated traverse walls the NGL will be fixed by GE. The top soil of 500mm thickness on entire plot having igloo, traverse wall from outer to outer edge of foundation of traverse walls around igloos in length and breadth to be stabilized by adding required cement as per design mix (to be done by contractor under own arrangement from NABL Govt approved Lab). The soil to be stabilized should be non expansive as approved by GE. The compaction to be done in layer upto 98% to achieve “K” value 5KN/m2/m which is to be checked before laying foundation on compaction site. (iii) The foundation to be laid as per Drg. The plinth height to be achieved 1.5m above NGL. The filling below foundation to be done using non expansive soil to achieve 98% compaction. This process is part of lump sum cost of building.

Provn of Sentry Post type 'A' complete all as shown in drawings as specified and as directed.

Provn of RCC Static water Tank of capacity 2,25,000 ltr complete all as shown in drawings as specified and as directed.

Provn of Fire Point complete all as shown in drawings in TD drawing No. CEAA/TD/148 Sheet no.1/1 as specified and as directed.

Provn of Fire Symbol and Division Display Board complete all as shown in drawings as specified and as directed.

Provn of of soak well 1.2m dia and 3 m deep complete excavation in any type of soil PCC 1:3:6 wall of honey combed maspnry complete all as shown in drawings in TD drawing No. CEAA/TD/80 Sheet no.1/2 & 2/2, as specified and as directed.

Provn of soak well 1.8m dia and 4.5 m deep complete excavation in any type of soil PCC 1:3:6 wall of honey combed maspnry as shown in TD drawing No. CEAA/TD/80 Sheet no.1/2 & 2/2 as specified and as directed.

NOTE: Schedule ‘A’ Part III to XVI are Prepriced by MES.

Lump sum price worked out for Excavation & Earthwork as listed in Sch `A’ Part III

Lump sum price worked out for Internal Water Supply as listed in Sch `A’ Part IV

Lump sum price worked out for Internal Electrification as listed in Sch `A’ Part V

Lump sum price worked out for Demolition/Dismantling of B/R & E/M item as listed in Sch `A’ Part VI

Lump sum price worked out for Additional/ Alteration item as listed in Sch `A’ Part VII

Lump sum price worked out for ROAD,PATH,HARDSTANDING,PQC ROAD,CULVERT as listed in Sch `A’ Part VIII

Lump sum price worked out for Sewage Disposal as listed in Sch `A’ Part IX

Lump sum price worked out for Area Drainage as listed in Sch `A’ Part X

Lump sum price worked out for Security Fencing and Gate as listed in Sch `A’ Part XI

Lump sum price worked out for External Water Supply as listed in Sch `A’ Part XII

Lump sum price worked out for External Electric Supply as listed in Sch `A’ Part XIII

Lump sum price worked out for Lightening Protection, Earthing for EOT as listed in Sch `A’ Part XIV

Lump sum price worked out for Refrigeration and Air conditioning as listed in Sch `A’ Part XV

Lump sum price worked out for Site Development-Retaining wall as listed in Sch `A’ Part XVI

SCHEDULE `A' PART-XVII MISCELLANEOUS ITEMS OF WORK (Note for items 40 to 115: The contractor shall quote his rate for each of these items separately. The estimated rate is left blank since the same is not prepriced by MES)

ADDITIONAL/ALTERATION

Taking down of U/S MCB TPN DB 4 way with MCBs complete all as specified and directed.

Taking down of Copper earthing and its connected strip complete all as specified and directed.

Taking down of LT XLPE cable of size 50 Sqmm 3.5 core complete all as specified and directed.

Taking down of LT XLPE cable of size 10 Sqmm 2 core complete all as specified and directed.

M&L Preparing new plastered or unplastered surfaces of walls and applying two coats of all weather coat exterior emulsion paint over a coat of primer in camouflage pattern and scheme as per user requirement complete all as specified and directed.

M&L applying two coats of plastic emulsion paint over a coat of primer on surfaces of walls and two coats of putty on partially prepared surfaces by brush/roller application complete all as specified and directed.

M&L for complete removal of existing treatment & preperation of old surface and applying two coats of all weather coat exterior emulsion paint over a coat of primer complete all as specified and directed.

M & L 12 mm thick wall lining Granite (of any type) tiles 12mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

S&F in repair PVC water tank cover with threaded coller suitable for 500ltr cap water tank complete all as specified and directed.

S&F in repair PVC water tank cover with threaded coller suitable for 1000ltr cap water tank complete all as specified and directed.

S&F fancy type brackets for fixing of curtain rod complete all as specified and directed.

S&F fancy type gloves for end caps of curtain rod complete all as specified and directed.

S&F in repair 15mm bore chromium plated cast copper alloy bib taps fancy type with , screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make: Prayag Cat No.-7706 or equivalent

S&F in repair 15mm bore chromium plated cast copper alloy stop valves / angle valve fancy type with , screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make : prayag Cat No-7710 or equivelent

S & F in repairs 15mm bore stop valve, cast copper alloy fancy type chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed complete all as specified and directed. . Make : prayag Cat No-7818 or equivalent

S & F towel ring round complete all as specified and directed. Make - prayag Cat No-BA-02 or equivalent

S & F Corner shelf of glass complete all as specified and directed. Make- prayag Cat No-BEA-42 or equivalent

S & F glass shelf 60mm complete all as specified and directed. Make : prayag Cat No-BEA-45 or equivalent

S & F cardiff health faucet with SS hose and hook complete all as specified and directed. Make : prayag Cat No-BEA-40 or equivalent

S & F in repair toilet paper holder of brass chromium plated including screw and chromiun plate brass wooden / plastic cleats complete all as specified and directed. Make : prayag Cat No-BA-38 or equivalent

S & F in repair brass chromium plated shower rose 75mm size (dia) with swivel joints including 195mm long brass chromium plated arm with bend 45 degree etc complete all as specified and directed.

S & F in repair 600 x 440 x 150mm cabinet mirror with 5.5mm thick glass and best quality PVC frame as per sample kept in GE Office complete all as specified and directed.

S & F in repair vitreous china counter top wash hand basin (self rimming) leed NC0483 (Size 600 x 400 x 175mm) colour brilliant / off white including fixing brackets and prepolished granite slab of size 1000 x 600mm size and cutting notch of required size as per the wash hand basin to be fixed in it complete all as specified and directed. Make : Kohler / Jaquar / Grohe/ESSCO (Cat Part No Jaguar SLS WHT 6601)

S & F tower bolt 100 mm of PTMT complete all as specified and directed.

S & F door handle D type 100 mm of PTMT complete all as specified and directed.

S&F dust guard vertical venetion blinds of any shade as approved with suitable hanging arrangements, tilting/ folding device complete all as specified and directed.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver complete all as specified and directed.

ROAD/HARDSTANDING/PQC

Material and labour for rolling and consolidating formation surface in cutting with 8 to 12 tonne power roller including filling in depressions which occurs during the process of rolling, rolling to required gradient and camber and testing of desire 'K' value before laying of first layer of GSB @ 60 Mtr C/C complete all as specified and directed.

M&L for 150 mm thick (completed thickness) Granular Sub Base Course(GSB) Grade V in a single/Double layer (as per table 400-1 and 400-2 of Morth & H specification) over compacted subgrade with stone aggregate by using motor grader,spreding, levelling and rolling with vibrratory roller of capacity 80-100 KN stactc wt.and consolidating to required gradiant and camber complete all as specified and directed.(finished surface tolerances as per table 900-1of Morth specification for road and bridge works.

M&L for 100 mm compacted thickness wet mix macadom (WMM) manufactured in WMM plant compacted (as per table 400-12 and 400-13) of Morth specifiactions of road and bridge works), with crushed stone aggregate of specified grading, spreding using senser paver and consolidating to required gradiant and camber complete all as specified and directed. If the water absorption value of coarse aggeregate is greater than 2%, the soundness test shall be carried out on the delivered at site. Finished surface tollerences as per table 900-1of Morth specification for road and bridge works.

M & L for Dry Lean Concrete ( DLC) of Thickness 125 mm having compressive strength 7 Mpa at 07 days ( Para 4.1 IRC:SP:49-2014) for each consective group of 5 cubes individual strength of each cube must not be less than 5.5 MPa at 07 days (Para 4.1 IRC:SP:49-2014) Size of aggregates not excceding 26.5 mm ( Grading and other physical parameters as table 600-1 of MoRTH specificaions for Roads and Bridge works/ table 1 IRC:SP:49-2014) Mixed in batching plant , transported to site and laid by sensor paver including spreading and compacting using double drum smooth wheelled vibratory rollers with 80-100KN static wt including necessary form work, finishing etc complete all as specified and directed. Transeverse joints, where required will be paid sepratly

Supply and laying ( No additional payment for overlap) 400 micron thick HDPE sheet (Virgin Quality) having minimum weight 390 gm/ Sqm over tack coat/sand cushion as specified in design with over lap between adjacent strip as minimum 100 mm and transverse joints at ends as minimum 150 mm etc complete all as specified and directed.

M&L for forming 25 mm width expansion joints in concrete slab for full depth of PQC using high RPM Diamond bit cutter. The joint be cleaned and filled with pre-moulded compressible polyethylene form backup road of 30mm dia ,or filler board and then priming top 15mm with approved primer and filling with polyurethane based sealent complying with BS -5212, BS-4254 and EL 141875-203 minimum MAF ± 30% , applying masked tape on the edges of joint to prevent accidental spillage of sealent and removing the masking tape after filling of sealent as per method specified by manufacturer complete all as specified and directed. The joint sealing shall be carried out by original approved applicator with sealent having 10 years performance guarantee. Work shall be carried out under recommended temperature condition specified by the sealent manufacturer. Top level of joint sealent should be as per application temperature conditions and season to avoid sealent extrusion/failure.

M&L for cutting of construction joints 25mm deep X10mm wide using high RPM diamond bit cutter, cleaning of surface and filling with closed cell, medium density cross linked polyethylene backup road of 12mm dia ,application of bond bracker tape on top of backup rod for complete width of the joint, priming top 15mm with approved primer , applying masked tape on the edges of joint to prevent accidental spillage of sealent and filling with polyurethene based sealent complying with BS-5212, BS-4254 and EN 141875-2003 and removing the masking after filling of sealent as per method specified by manufacturer complete all as specified and directed. The joint shall be treated with a coat of lime wash , bituminus paint before the adjoining bay is laid. The joint sealing shall be carried out by original approved applicator with sealent having 10 years performance guarrentee. Work shall be carried out under recommended temperature conditioned specified by the sealent manufacturer. Top level of joint sealent should be as per application temperature conditions and season to avoid sealent extrusion/failure. Forming construction joint with olyethylene foam backer rod of 10mm dia, specified primer and filling with polyurethane based sealant, complete all as specified and as directed.

Material and labour for Forming dummy/contraction joint using high RPM diamond cutter with and initial saw cut of 3 mm soon after the concrete has set, upto a depth of 1/3 to 1/4 the thickness of the slab, widening the first saw cut to 6mm width and 24 mm deep from the top. Joint to be filled with closed cell, medium density, cross linked polyethylene foam backup rod of 8mm dia for complete length of the joint, priming the 15 mm with approved 15 mm with approved primer, applying masking tape on edge of joints to prevent accidental spillage of sealant and filling with polyurethane based sealant complying with BS-5212,BS-4254 and EN 141875-2003. The joint sealing shall be carried out by original approved applicator with sealant having 10 years performance guarantee. Work shall be carried out under recommended temperature condition specified by the sealant manufacturer. Top level of joint sealant should be as per application temperature conditions and season to avoid sealant extrusion/failure.

EOT Crane

Design Supply and fix , testing and commissioning outdoor type medium duty electrically operated FLAME PROOF double girder over head travelling crane (EOT) duty class M5 design and manufacturing in accordance to IS -3177 of 1999 , IS -807 of 2006 and IS 2148 capable to handle 10 (Ten Ton) capacity load (SWL) with centre to centre clear span 15 Mtr and 18 Mtrs travel length , longitudinal travel limited to 1.5 mtr away from the wall on both side suitable for 415 volt 3 phase 4 wire AC supply system, with necessary steel supporting structure with clear hook height 5.2 mtr from FFL including provision of gantry girder and rail ,bridge girder and rail , all electrical components, control cable of suitable size,limit switches,electrical control panel safety controlled etc, floor operated with moveable pendent controlled to be oprated by means of push button from floor level independently of crab, position with protative panel including down shop lead (DSL) trailing cable for CT motion and DSL of Feston type with FRLSH cable for LT motion complete all as including painting with fire resistant paint as per manufacturers instruction , specification all as per the standard norms including supply and fixing of suitable size Square bar rail as per manufacturer's instructions . All necessary civil work for installation of gantry girder and rail should be provided by the contractor. The motors are used specially crane duty suitable for frequent starting, reversing and braking in accordance with IS 325, motors are TEFC, dust proof, flame proof, insulation class F, IP-65 protection for hoisting CT & LT motions. The speed of motor shall be control using variable speed by installing VVF drive in the control panel. The wheel and hook should be coated with non ferrous metal to avoid metal to metal contact. Required speed are as below-Hoist - Main speed 3 mtr/ min , Creep speed 1 mtr/min Cross travel- Main speed 10 mtr/min , Creep speed 2 mtr/min lognitudal travel- Main speed 10 mtr/min , Creep speed 2 mtr/min

Note :- (i) Considering large span of the crane, Fabrication work of crane girder can be done at site. The joint will however not to be provided at the same points of maximum stress and jointing shall be tested all as per relevant IS in order to ensure strength at the joints is not less than the structure of the girder. (ii) Design of gantry girder shall be submitted to Engr-in-charge for approval (iii) Rate of gantry girder and rail included in the cost of item. (iv) The cost of 4 core PVC FRLSH copper power cable of suitable size with MS conduit pipe of suitable size from switch board to crane is deemed to be included with unit rate of item.

Design Supply and fix , testing and commissioning indoor type medium duty electrically operated FLAME PROOF double girder over head travelling crane (EOT) duty class M5 design and manufacturing in accordance to IS -3177 of 1999 , IS -807 of 2006 and IS 2148 capable to handle 10 (Ten Ton) capacity load (SWL) with centre to centre clear span 18 Mtr and 36 Mtrs travel length , longitudinal travel limited to 1.5 mtr away from the wall on both side suitable for 415 volt 3 phase 4 wire AC supply system, with necessary steel supporting structure with clear hook height 5.2 mtr from FFL including provision of gantry girder and rail ,bridge girder and rail , all electrical components, control cable of suitable size,limit switches,electrical control panel safety controlled etc, floor operated with moveable pendent controlled to be oprated by means of push button from floor level independently of crab, position with protative panel including down shop lead (DSL) trailing cable for CT motion and DSL of Feston type with FRLSH cable for LT motion complete all as including painting with fire resistant paint as per manufacturers instruction , specification all as per the standard norms including supply and fixing of suitable size Square bar rail as per manufacturer's instructions . All necessary civil work for installation of gantry girder and rail should be provided by the contractor. The motors are used specially crane duty suitable for frequent starting, reversing and braking in accordance with IS 325, motors are TEFC, dust proof, flame proof, insulation class F, IP 54 protection for hoisting CT & LT motions. The speed of motor shall be control using variable speed by installing VVF drive in the control panel. The wheel and hook should be coated with non ferrous metal to avoid metal to metal contact.. Required speed are as below- Hoist - Main speed 3 mtr/ min , Creep speed 1 mtr/min Cross travel- Main speed 10 mtr/min , Creep speed 2 mtr/min lognitudal travel- Main speed 10 mtr/min , Creep speed 2 mtr/min

Note :- (i) Considering large span of the crane, Fabrication work of crane girder can be done at site. The joint will however not to be provided at the same points of maximum stress and jointing shall be tested all as per relevant IS in order to ensure strength at the joints is not less than the structure of the girder.(ii) Design of gantry girder shall be submitted to Engr-in-charge for approval (iii) Rate of gantry girder and rail included in the cost of item. (iv) The cost of 4 core PVC FRLSH copper power cable of suitable size with MS conduit pipe of suitable size from switch board to crane is deemed to be included with unit rate of item.

Supply and fix flame proof control panel in cast allumium alloy LM6 construction certified by CMRS Dhanbad for Group IIA and IIB consisting of :_ MCCB 4 Pole 16 KA 40 Amp with encloser-01 Nos

EXTERNAL ELECT SUPPLY

Supply and install HT 11 KV outdoor extensible type, cubical, 7-way (LRRL-2LBS+5VCB) Gas (SF6) Insulated RMU comprising with incomer – 2 Nos x LBS (Load break switches) and outgoing – 5 Nos x VCB of rating of each 630 Amp 3 phase 50 cycles 12 KV, 20KA/ 3 Sec Ambient temperature-(-5 degree Celsius to +55 degree Celsius), Manual operated SF6-Breaker having copper busbar 600 Amp rating, cast resin tank with, LV current transformer compatible with self powered relay & 11 KV regin cast PTs (one set pf 3 Nos) with separate metering chamber complete Make SIEMENS model 8DJH ST/Equivalent in ABB. Each Load break switch will have the following:- (i) Load Break Three Position switches with position ON-OFF-Earth (ii) Manual operated spring mechanism ON-OFF-Earth for 630A Load Break switch. (iii) Mechanical indicators for position ON-OFF-Earth (iv) Socket for Capacitive Voltage Indicator (“Live Cable” Indicating LEDs energized thru Capacitive Voltage Dividers) (v) Padlocking facility (vi) Cable box suitable for cable termination of 1 No, 3C x 120 sqmm XLPE Cable.

Accessories with each RMU includes:- (i) Operating handle- 1 Nos . (ii) Right angled cable boots Make Siemens/ equivalent- 4 x sets (iii) Capacitor voltage indicator type HR-ST- Make Hortsmann -4 Nos Separate Metering Chamber having:- (i) 3 phase, 3 Limb draw out type bus connected Epoxy potential transformer, ratio 11KV/√3/110V/√3 AC accuracy 1.0 burdon 50VA-01 (ii) Digital type voltmer-1 Nos (iii) RYB indication -1 set Note: (i) RMU shall be outdoor plinth mounted. (ii) Erections commissioning and civil work (Plinth protection) for RMU is deemed to be included with unit rate. The plinth protection details as per the manufacturer instruction.

i) Cable terminals cable bushing situated not beyond 300 mm or as per OEM tested design from cable cover to allow ease of access for installation/testing/replacement purpose) with door arrangement for enhanced safety (IP54+IP3X) interlocked to prevent access up to 11 KV, 185 Sq mm, 3 Core, along with XLPE AL cable termination Each set of 03. ii) Right angle boots (push on type) Each set of 03 vii) 3 O/C + 1 E/F self-powered numerical protection relay with low and high set for Over current and Earth Fault. Relay should have facilities to display the maximum loaded phase current also. Relay shall record minimum 5 fault records with time stamping. Relay shall be communicable with RS 485 Port on MODBUS Protocol. – 01No/ per VCB ougoing viii) Relay for OTI / WTI / B – relay protection – 01 No iii) Associated ring Core cast- resin insulated CT s 50/1 Amps, 2.5 VA, 10 P 10 Protection – Each set of 3 x) Arc proof cable covers having cable entry from bottom, front with interlocking mechanism including earth switch – 01 No. xi) Capacitive voltage indication fixed type system as per IEC 6123 with LED – 01 Set xii) ON, OFF, Earth mechanical indication on the front mimic of the panel – 01 No xiii) Emergency trip push button – 01 No

01 No Bus – connected, fixed – type Auxiliary transformer with floor- mounted compartment of matching height and depth, positioned along – side RMU to provide required aux. supply for spring charging motor and metering consisting of following accessories: i) 3-Ph (11 KV / rt3): 230 VAC, 500 VA Auxiliary transformer – 01 No. along eith Trivector meter ii) 2X12 Volt DC battery – 01 Set iii) Battery charger – 01 No, with indiacation of status of functioning iv) HRC fuse links for primary side isolation and AC/DC MCBs for secondary isolation – 01 Set v) Voltmeter & RYB LED indications to confirm AC/DC supply availability – 01 Set vi)Anti – condensation space – heater – 01 No. vii)CFL lamp for illumination and 3 pin socket with switch – 01 No.

(D) Standard mano meter -01 for each tank, Operating handle - 02 , cable clamping provision(standard)-01 /for every cable enrty ,Operation and maintance manual - 01, installation and commissioning manual - 01, Foundation as per OEM Recommendation ( Earth Work and PCC works) for placing RMU on plinth is deemed to be included in the cost quoted. Height of plinth should not be less than 0.45 mtrs from ground level. NOTE :- (a) The above module consisting of Load break Switchs and VCBs shall be alligned appropriately and must have electrical and mechanical interlocking as per latest electrical safety norms including installation on plateform as recommended by OEM complete.

Supply and fix lightening arrester Gap less metal Oxide type HT 11 KV 10 KA station class complete all as specified and directed. Note: Set comprises for three phase system

Supply, Installation and testing of water cooled Diesel Engine driven Prime duty Generating Set of net capacity after all derating factors net of not less than 62.5 KVA/50 KWe ,50Hz 415 volt 3 phase, 4 wire,0.8 lagg, 84 hp minimum Required Power for Rated kVA (hp) along with AMF system with Acoustic Enclosure exhaust silencer-residential in line , as per the noise emmission standards laid down by MoEF / CPCB Norms. Along with pollution control devices, accessories supporting structures fitted in the exhaust system with out effecting the DG output as per latest green trubinal and CPCB norms for controlling toxic exhaust gases and particle matter above 2.5 ppm.

A) Engine comprising of the following: Rugged engine natural liquid cooled (EG Compleat 50:50) with radiator as secondary media with world class OEM such as Cummins/Perkins/Kohler/Greaves/Ashok Leyland Engines for powered diesel generator set along with these specifications of Advanced in-cylinder technology turbo charged , air cooled aspriated to meet latest emission norms without any after-treatment device. Class defining technology engine is designed to meet stringent exhaust emission tests as per revised MoEF norms, thus offering environment friendly power Compact in size with optimum power to weight ratio, 4 cylinder, In-line 4 stroke, radiator cooled engine Well designed air handling system with Dry type, heavy duty, replaceable paper element air cleaner with restriction indicator, Air to air after cooling, Optimised turbocharger for increased altitude capabilities, Best in class fuel economy with Inline fuel pump with A1 class mechanical governing, Spin on fuel filter, Standard integral set-mounted radiator system, designed and tested for 50°C ambient temperature, Full flow spin on lube oil filter, First fill of lube oil and coolant, Electrical starter motor with soft start engagement feature, Battery charging alternator,1 x 12 V DC battery/Alternator

b) Alternator PMG type comprising of the following: Stamford UC/jyothi/crompton alternator frames from Technologies Brushless type, Screen protected, Revolving field, Self excited alternator conforming to IS/IEC 60034-13 Phase reconnectable winding with 12 terminals brought out for connection Dedicated winding specially designed for 1 phase and 3 phase operation Better motor starting capability Best in class efficiency Compact design with sealed bearings for longer life and lesser maintenance Impregnation on all wound components for better mechanical strength with Alternator of IP 23, Voltage regulation (Max.)±1%, Class of Insulation H Class, Winding Pitch 2/3, Stator Winding Double layer lap Rotor Dynamically Balanced, Waveform distortion/ Total Harmonic Distortion No load < 1.5 %, Non distorting balanced linear load < 5 %,Maximum Unbalanced Load across phases# less than or equal to 25%, Telephonic Harmonic factor < 2% alternator capacity output shall not be less than 62.5 KVA / 50KWe ,50Hz 415 volt 3 phase, 4 wire,0.8 lagg. 87 Amp / phase

c) Control Panel comprising of the following: AMF / Control panel is manufactured with 14/16 gauge CRCA sheet and is powder coated for weather-proof and long lasting finish. The control panel consists of the following parts of makes as per OEM recommendation: microprocessor based generator set monitoring and control system. along with AMF Functionality is inbuilt and this control includes an intuitive operator interface that allows for complete generator set control as well as system metering, fault annunciation, configuration, and diagnostics, Copper bus bars with suitable capacity with incoming/outgoing terminals, Indicating lamps for ‘Load ON’ and ‘Set Running’, Instrument fuses / MCBs duly wired and ferruled, Circuit breakers of suitable rating with overload and short circuit protections. with motorised change overs /on load power contactors with copper busbars, cables and protective accessories with load / bypass arrangements Resednetial type silencer: Critical grade silencer suitably optimized to meet stringent noise emission standards laid down by MoEF / CPCB along with MS supporting structures .along with thermal Insulation on horizontal pipe with Mineral Wool/ Asbestos Rope 50mm Thick wire mesh and 26 gauge aluminum cladding (12")

(d) Controller should be compatible to the following specifications: (i)AMF Functionality controllers of Makes from the OEM : Deep Sea/ Cummins/ Wood Ward/ Com Amp (ii) Intuitive operator interface which includes LED backlit128X64 pixel graphic display with tactile feel soft-switches. Indications - Generator set, Utility Status Lamp. (iii)Remote start-stop with Engine Metering: Oil pressure, Engine temperature, Starting battery voltage, Engine running hours (iv)AC Alternator Metering: L-L Voltage and L-N Voltage, Current (phase and total), KVA (phase and total) and Frequency. kwh, Total & per phase (kw & kVA), PF, Utility Voltage and Freq. (v)Engine Protection: Low lube oil pressure, High/Low coolant temperature, Battery Over/Under/Weak Volts, Fail to Crank/Start, Sensor failure, Cranking lockout, Low fuel level. (vi)AC Alternator Protection: Over/Under Voltage, Over/Under Frequency, Loss of AC sensing. Overspeed, Over Current. (vii)Data Logging: Engine hours, Control hours and upto 5 recent fault codes (viii)Configurable glow plug control, Cycle Cranking (ix)12/24 Volt DC operation, Sleep mode, Modbus interface (RS485 RTU), In Power compatible (PC based service tool),Certifications - meets the requirement of relevant ISO, EN, Mil Std. and CE standards

(e)Maintenance due alarm based on Engine Run Time and due date, Exercisor scheduler (f) Remote HMI, Digital electronic governor with temperature compensation and smooth starting, digital AVR for shunt of PMG excitor with Torque monitoring (e) All pipe line connections, valves etc.required for the lube oils, fuel and cooling system (f) Battery & Battery charger of rated capacity as per the alternator/ Engine compatability g) Mounting Arrangement shall be of the following: (i) Engine and alternator are mounted on a common MS fabricated base frame with AVM pads. (ii) Base frame with integral fuel tank is provided with drain plug, air vent, inlet and outlet connection, level indicator and provision for cleaning (h) Fuel Tank of capacity 12 hrs running capacity along with Fuel pipe MS c class 25mm ID with bends , flanges , valves, tees and bends. (I) Residnetial type silencer with MS pipe as designed by the OEM horizontal Exhaust pipe complete with bends and flanges of adequate length not less than 10 Mtr. along with thermal Insulation on horizontal pipe with Mineral Wool/ Asbestos Rope 50mm Thick wire mesh and 26 gauge aluminium cladding (12"). (j) Controll/ service cables shall be of 4cx 2.5 sqmm, 24 c x 2.5 sqmm , 2 c x 2.5 sqmm, and 8c x 0.75 sqmm shielded control cables ,pvc insulated copper armoured, controll panel for auxilaries with starters for pumps,heaters etc

(k) RCC foundation with necessary earth work ,PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in foundation, filling and mass concrete / RCC M-30 (20 mm graded aggregate) as in foundations, Plinth beam along with necessary form work / TMT bars of 10mm dia and over cut to length bend to shape required including cranking, bending, spirally for hooping for columns, hooking ends and bidning with and including MS wire (annealed) not less than 0.9mm dia securing with clips / 10 mm thick plastering on fair faces of brick work or concrete surface in CM (1:6),even and smooth without using extra cement / Sand filling in layers around the foundation including watering and consolidation as per OEM dimensions (l) Acoustic Enclosure shall comprise of the following (i) Specially designed to meet stringent MoEF/ CPCB norms of 75 dBA @ 1mtr at 75% load under free field conditions. (ii) The Acoustic Enclosure as per CPCB Norms is made of CRCA sheets in Munselgreen shade and a structural/ sheet metal base frame painted in black. or any other standard colour as specified by the OEM (iii) High quality noise absorbant and fire-retardant gradeacoustic insulation material (P.U. Foam) complying to IS8183 designed to have optimum serviceability (iv) Air inlet louvers specially designed to operate at rated load, Made on special purpose CNC machines for consistency inquality and workmanship (v) 11 tank pretreatment process and UV resistant powder coating of all parts to withstand extreme environment, Use of special hardware for longer life Flush styling - no projections, Fluid drains for lube oil and fuel, Fuel filling arrangement inside the enclosure

Supply and installation, testing commissioning, factor made, (CPRI approved manufacture), outdoor type, LT panel board, confirming to IS 8623 with IP-54 protection, made out of 3.15mm thick CRCA sheet, 415 volt, 3 phase , 50 Hz supply mounted on and including MS angle section 50 x 50x 6mm frame with front and back openable, double door with provision of locking arrangement dust & vermin proof, gasket, TPN busbar shall be insulated with colour coated heat shrinkable sleeves and shall be mounted on proper insulator, gland, welding hinges of dust proof, overall powder coated complete all as specified and directed & connecting of the following equipments

(a) Bus bar chamber of 3 phase 4 strip 415 volts with 200 Amps copper strip 1 Set. (b) MCCB 125 Amp 36 KA 4 pole - 01 Nos (c) MCCB 63 Amp 16 KA 4 pole - 03 Nos (d) MCCB 40 Amp 16 KA 4 pole - 01 Nos (e) MCB 40 Amp C Curve DP- 02 Nos (f) Voltmeter digital 0-500 volt - 01 (g) Amp meter digital 0-200 Amp - 01 (h) Indicator lamp yellow, Red, Blue - 01 Set (j) Complete Int wiring with copper conductor - 01 Lot (k) Extra space for two feeders Note : (I) All termination of cable should be provided with copper lugs/ thimbles and suitable size of glands & rate for the same is deemed to be included in the item.

Supply and install testing and commissioning outdoor LT electric panel (KIOSK) consisting of doble door, weather proof, separate compartment with locking arrangment, cubical panel floor mounting fabricated out of 3.15 mm thick CRCA sheet on angle iron frame of 25 x 25 x 5mm and legs made of angle iron 40 x 40 x 6mm, painted with powder coated and pre-coated primer including necessary PCC 1:3:6 type C2 foundation and earth work and comprising the following

(a) Bus bar chamber of 3 phase 4 strip 415 volts with 100 Amps copper strip 1 Set. (b) MCCB 63 Amp 16 KA 4 pole - 01 Nos (c) MCCB 40 Amp 16 KA 4 pole - 03 Nos (d) MCB 40 Amp C Curve DP- 02 Nos (e) Voltmeter digital 0-500 volt - 01 (f) Amp meter digital 0-200 Amp - 01 (g) Indicator lamp yellow, Red, Blue - 01 Set (h) Complete Int wiring with copper conductor - 01 Lot (j) Extra space for two feeders Note : (I) All termination of cable should be provided with copper lugs/ thimbles and suitable size of glands & rate for the same is deemed to be included in the item.

Supply and install testing and commissioning outdoor LT electric panel (KIOSK) consisting of doble door, weather proof, separate compartment with locking arrangment, cubical panel floor mounting fabricated out of 3.15 mm thick CRCA sheet on angle iron frame of 25 x 25 x 5mm and legs made of angle iron 40 x 40 x 6mm, painted with powder coated and pre-coated primer including necessary PCC 1:3:6 type C2 foundation and earth work and comprising the following

(a) Bus bar chamber of 3 phase 4 strip 415 volts with 150 Amps copper strip 1 Set. (b) MCCB 100 Amp 36 KA 4 pole - 01 Nos (c) MCCB 63 Amp 16 KA 4 pole - 03 Nos (d) MCCB 40 Amp 16 KA 4 pole - 01 Nos (e) MCB TPN C Curve 40 Amp- 02 Nos (f) Voltmeter digital 0-500 volt - 01 (g) Amp meter digital 0-200 Amp - 01 (h) Indicator lamp yellow, Red, Blue - 01 Set (j) Complete Int wiring with copper conductor - 01 Lot (k) Extra space for two feeders Note : (I) All termination of cable should be provided with copper lugs/ thimbles and suitable size of glands & rate for the same is deemed to be included in the item.

Supply and fixing HT/LT cable route indicator cast iron of suitable size with height of 1.5 metre along with HT/LT cable trench including planting in ground with PCC 1:3:6 (0.3x 0.3 x 03m) complete all as specified and directed.

M&L for Boring holes under road pavement hardstanding by trench less technology using ultrasound technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 Mpa working pressure complete all as specified and directed.

Supply and fixing GI pipe bracket light grade of 50mm dia ISI marked duly bent to shape with an angle including clamps, nuts bolts, washers painting with aluminium paint etc. complete all as specified and directed (Note : The total length of the bracket shall be 1.5m)

Supply polycarbonate unbreakable junction box suitable for pole mounted out door type complete with FI clamp & nuts, bolts, washers and including copper bus bar 4 pole x 10 amp and one MCB SPN 0.5.5 Amp 10 KA complete

Supply and fix PVC insulated and over all PVC sheathed stranded copper conductor wire 1.5 sqmm x 3 core ISI marked including steel conduit pipe 20mm complete from fitting to pole junction box complete all as specified. Note : PVC copper wire 1.5 sqmm x 3 core and steel conduit pipe 20mm will be measured as combine as one RM length

Supply and install testing and commissioning outdoor LT Bus bar chamber consisting of double door, weather proof separate compartment with locking arrangement, cubical panel floor mounting fabricated out of 3.15 mm thick CRCA sheet on angle iron frame of 25 x 25 x 5mm and legs made of angle iron 40 x 40 x 6mm, painted with powder coated and pre coated primer including necessary PCC 1:3:6 type C2 foundation and earth work and comprising the following (All plinths security light main distribution) (a) Bus bar chamber of 3 phase 4 strip 415 volts with 40 Amps copper strip 1 Set. (a) MCB 20 Amp C Curve TPN- 01 Nos (b) Voltmeter digital 0-500 volt - 01 (c) Amp meter digital 0-200 Amp - 01 (d) Indicator lamp yellow, Red, Blue - 01 Set (e) Complete Int wiring with copper conductor - 01 Lot (f) Extra space for two feeders Note : (I) All termination of cable should be provided with copper lugs/ thimbles and suitable size of glands & rate for the same is deemed to be included in the item.

Supply and install SPN DB single door 4 way with MCB 6-32 Amp C Curve DP-01 Nos and MCB 0-5-5 Amp C Curve SP-02 Nos complete (All plinths security light main distribution) complete all as specified and directed.

Material and labour for sand cushioning to all around the cable protection of natural Tibba sand complete all as specified and directed. (Note : Punning thickness will be measured and paid for payment purpose)

Supply and lay stone patti quarry faced Jodhpur type 4 to 5 cm thick and 25 to 30 cm wide putting on cable abutting to each other for cable protection complete all as specified and directed.

EXTERNAL WATER SUPPLY

Supply and fix Pumping sets, 500 LPM Discharged at 70 Mtr head centrifugal, electric driven, supply and install complete inclusive of starter and PCC foundation complete all as specified and directed.

Supply and fix foot valve conforming to IS 4038 of size 150 mm 6 inch dia complete all as specified and directed

Supply and fix cast iron air valve with two air outlets 50 mm dia bore conformiing to IS 14845 and fixing up in DI water supply mains of size 100 mm 4 inch dia complete all as specified and directed.

Supply, install, testing and commissioning outdoor LT electric panel ( KIOSK) consisting of double door, weather proof, separate compartment with locking arrangement, cubical panel floor mounting fabricated out of 2 mm thick CRCA sheet on angle iron frame of 25x25x5mm and legs made of angle iron 40x40x6mm, painted with powder coated and pre coated primer including necessary PCC 1:3:6 type C2 foundation and earth work and comprising the following :- (a) Bus bar chamber of 3 phase 4 strip 415 volts with 100 Amps copper strip 1 set (b) MCCB 63 Amp 16 KA 4 pole -01 Nos (c) MCCB 40 Amp 16 KA 3 pole -02 Nos (d) Voltmeter digital 0-500 volt = 01 (e) Amp meter digital 0 -200 Amp = 01 (f) Indicator lamp yellow , Red , blue - 01 Set (g) Complete Int wiring with copper condutor - 1 Lot (h) Extra space for two starters Note :(I) All termination of cable should be provided with copper lugs/thimbles and suitable size of glands & rate for the same is deemed to be included in the item

Material and labour for construction of for Valve Pit /Chamber 1200 x 1200 x 1200mm (internal) with solid block masonry built in CM 1:6 ,over 150 mm thick PCC foundation 1:3:6 type C2, 10mm thick internal CM 1:6 & 12mm thick external plaster in CM 1:4 provided with 3 mm thick MS sheet cover 3.15 mm thickness along with angle iron frame of size 40x40x6 mm and MS angle iron chamber frame fixed in coping in PCC 1:2:4 type B-1 with locking arrangement and handle, painting of MS work with one coat of red oxide primer and two coat of synthetic enamel black paint complete including excavation & earth work,RFR, removal in any type of strata complete all as shown on drawing No.CEAA/TD/57 sheet No 1.1,dated 28.05.92,amended upto 31.12.92, but of internal size 900mm(L) x 900mm(B) x 900mm (D) etc complete all as specified and directed.

SEWAGE DISPOSAL

Supply and installed prefabricated advance Septic tank for 16 users made out of LLDPE (Linear Low Density Polyethylene) including excavation, returning filling and removal in any type of soil, PCC 1:4:8 below foundation, vent shaft etc complete with up flow filter including media. Septic tank shall be made of Roto moulding process,having diameter and height as per manufacturers design wih usual process variation.The tank shall have two chambers (zones),i.e.,Settling zone and Film Zone (High Specific Surface Area) with pall ring media.The first chamber to work as a solid separation zone where the settleable solids settle down and are further degraded anaerobically.Second stage is high specific surface area (100sqm m/cubic m) through fixed film plastic media to retain high mass of anaerobic microorganism to degrade the organic matter in the sewage complete all as specified and directed. Make of Septic tank shall be Sintex or equivalent make approved by GE.

Supply and installed prefabricated advance Septic tank for 30 users made out of LLDPE (Linear Low Density Polyethylene) including excavation, returning filling and removal in any type of soil, PCC 1:4:8 below foundation, vent shaft etc complete with up flow filter including media. Septic tank shall be made of Roto moulding process,having diameter and height as per manufacturers design wih usual process variation.The tank shall have two chambers (zones),i.e.,Settling zone and Film Zone (High Specific Surface Area) with pall ring media.The first chamber to work as a solid separation zone where the settleable solids settle down and are further degraded anaerobically.Second stage is high specific surface area (100sqm m/cubic m) through fixed film plastic media to retain high mass of anaerobic microorganism to degrade the organic matter in the sewage complete all as specified and directed. Make of Septic tank shall be Sintex or equivalent make approved by GE.

FENCING GATE

Dismantling barbed wire any type and in any position

S & F galvanised punched tape concertina coil of 1050mm dia (dia of coil when unstreched) and 2.6 mm dia of core wire and shall not be less than 78 Nos. of spiral in each 10 RM length & fixed between double chain link fencing with GI wire complete all as specified and directed.

S & F medium carbon steel (EN-8 grade) sliding gate bottom wheel double flanged of outer dia 150mm inclu all arrengement of hinges and other connected items of wheel for fixing to door with permanent lubricated & proper sealed bearing, fixed to door bottom frame by welded/riveted/bolted as per manufacturer guidence all as approved by GE and directed at site.

S&F medium carbon steel (EN-8 grade) top wheel (double roller set) set of hanger doors of outer dia 190mm inclu all arrengement of hinges and other connected items of wheel for fixing to door with double ball bearing type of make - SKF or equivalent & fixing to MS frame work by means of welded/riveted/bolted complete all as specified and directed.

INTERNAL ELECTRIFICATION

Supply and fix 20W 5700 K LED fitting with lumen efficiency not less than 110 lumen/watt, pf 0.8, IP20, white powder coated extruded aluminium body with high quality LGP and PMMA diffuser including separate HPF driver suitable for armstrong and grid ceiling and separate accessories available for mounting of size 600mm x 600mm complete all as specified and directed.

Supply and fix flame proof-weather proof distribution board, duct and vermin proof 8 way DB IP-65, LM-6 body, appropriate size with epoxy powder coating,suitable for and including the following scheme and MCBs:- (a) Incoming : (i) MCB 32 Amps, DP, 10 KA-01 Nos, (b) Outgoing : MCB, SP, 10 Amps , 10 KA -04 Nos, (ii) MCB, SP. 6 Amps 10 KA-02 Nos.

Supply and fix flame proof-weather proof distribution board, duct and vermin proof 2 way DB IP-65, LM-6 body, appropriate size with epoxy powder coating,suitable for and including MCB-32 Amps complete all as specified and directed.

ROAD/HARDSTANDING/PQC

Supply only polyester triangular fibres/non circular fibres having tensile strength 3600-6000 Kg/cm2, designed for melting point more than 250 degree Celsius @ 0.25% weight of cement in controlled pavement qulity cement and having specific gravity of 1.34 to 1.40 complete all as specified and directed.

Supply and fix reinforced concrete NP-4 pipe of 300 bore with one collar per length all as directed.

RAIN WATER DISCHARGE

Material and labour for reserve boring of 150mm dia including perforated ring pipe to runoff rain water from ground level to the depth of up to 5m and dicharge rain water through existing gypsum layer. Rate for this including following (a) Drilling/boring of 150 mm dia upto to depth of 5m at the bottom of collection pit (b) Perforated pipe of 150mm dia with casing up to depth of 4.5m (c) Collection pit of size 2m x 2m and dept of 1.5m including excavation and removal of excavated soil to a distance of 50m. (d) RCC wall of collection pit as ring of size 100mm thick RCC in M-25 in entire depth of collection pit (e) 100mm thick PCC in1:4:8 at bed of collection pit

Sch of credit Rs 256172.50

DHARIWAL TRADERS PRIVATE LIMITED

MANGLA AMIT BUILDERS PVT LTD

SOOD ASSOCIATES PVT LTD

SARAOGI BUILDERS LIMITED

Parth Infrastructure Pvt. Ltd.

Hariom Projects Pvt Ltd

GANGA INFRABUILD PVT LTD