Special repair work of Haryana Roadways Workshop B.B. Marg, Kingsway Camp, Delhi. (Recall)

Amount

Dismantling brick work, Tile Masonry or Tile Lining and Tile Terracing (b) in cement. [HSR 8.5(b)]

Reinforced cement concrete with cleaning and straightening and cutting of bars if required. [HSR 8.6 (e)]

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the wall is not to be dismantled:- (a) Door [HSR 8.18(a)]

Removing glazing fixed or openable (wood and steel) including chowkhat holdfasts and concrete blocks:- (b) by making recesses in walls when the wall is not to be dismantled.[HSR 8.23 (b)]

Dismentling brick or flagged stone slab flooring including concrete base.[HSR 8.27]

Scraping of white wash and colour wash [HSR 8.32 (a)]

Scraping cement plaster.[ HSR 8.32 ( c ) ]

Dismantling white or coloured glazed tiles (to be carefully removed} [HSR 8.38]

Cement concrete 1:1½:3 with stone aggregate 20mm nominal size in first storey upto 4 metres above plinth level.[HSR 10.60]

First class brick work laid in cement sand mortar 1:4 in foundation and plinth.[HSR 11.4] Note:- (i) Where any single storey exceeds 4 metres in hieght, the rate for brick work of wall, sup porting the roof, having height greater than 4 metres will be increased by Rs. 8.25 per cum, for every additional height of 2 metres, or part thereof. this additional rate of brick work shall also be added for brick work in subsequent storeys. this additional rate is not to be paid for brick walls having height less than 4 metres within the storey; though over all height of storey may be over 4 metres, such as in the case of any low partition walls, or walls below a mezzanine inter-floor, not going above the mezzanine floor level, and upto the full storey height. In case of walls of varying heights, average height shall be considered for fixing the rate.

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (a) 100 mm dia PVC pipe 6 kg. pressure (Note:- Reputed make PVC Pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.89] (a). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing and fixing PVC Bend ISI Mark. (a) 100 mm dia PVC Bend (Note:- Reputed make PVC Bend such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.90](a). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Base course of floors consisting of 100mm thick cement concrete 1:8:16 and 100mm sand or stone filling.[HSR 14.1]

Screed of 50mm of thick cement concrete 1:8:16 to be laid below the topping.[HSR 14.6]

Kotah stone flooring minimum 25mm thick in any pattern as specified over 20mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing [HSR 14.62] Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Extra for noising in treads of steps of Kotha stone slab.[HSR 14.65]

Kotah stone 20 mm thick in skirting risers of steps, dados and wall facing (lining) and pillars laid on 12 mm thick cement coarse sand plaster 1:3 laid and jointed with neat cement slurry, mixed with pigment to match the shade of stone including rubbing and polishing including labour for fixing cramps, dowels and pins etc. [ HSR 14.66 ] Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

50mm thick ironite floor consisting of 40mm thick cement concrete 1:2:4 base and top layer 10mm thick laid with one part of ironite and grey cement mixed together in the ratio of 1:4 by weight to two parts of hard granite chipping 6mm guage by volume finishing smooth with hard rubbing.[HSR 14.74]

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-fcturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (b) Size of ceramic glazed tiles 300x450mm Note: the tiles shall be of premium quality (Ist Quality of reputed manufacturer like : NITCO, KAJARIA, SOMANI, ORIENT BELL, RACK & SIMPOLO [HSR 14.92(b)]

Providing, laying and fixing vitrified/ceramic anti skid tiles of any size of approved make in floors laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note: the tiles shall be of premium quality (Ist Quality of reputed manufacturer like : NITCO, KAJARIA, SOMANI, ORIENT BELL, RACK & SIMPOLO [NS]

Providing and laying Pre-polished Granite Stone 17 mm & above Like :- S-White, Steel Grey, Tan Brown, Marigold, Crystal Blue, Rajasthan Black, Copper Silk in skirting/ dados, risers of steps, pillars, wall facing, laid in any pattern as specified over base of 12mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite including labour for fixing cramps pins and dowels etc. (NS)

Providing and laying Pre-polished Granite Stone 17 mm & above (Colors Like :- S-White, Steel Grey, Tan Brown, Marigold, Crystal Blue, Rajasthan Black, Copper Silk) in flooring, laid in any pattern as specified over base of 20mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite stone. (NS)

Providing, laying and fixing ceramic & Glazed tiles / vitrified tile / of any size of approved make in floors/dados,laid in any pattern as specified over base of 3 mm thick adhesive of reputed brands such as Pidilite,Laticrete,Ferrouscrete & Valendure as per IS specification 15477-2004 using 5 Kg .adhesive slurry mixed with pigment to match the shade of tiles including cost of tiles. Note: the tiles shall be of premium quality (Ist Quality double charge of reputed manufacturer like : NITCO, KAJARIA, SOMANI, ORIENT BELL, RACK & SIMPOLO [HSR 14.97] [NS]

Providing edge moulding to 17-20mm thick granite stone counter, vanities etc. including matching polish to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge (Moulding).[HSR 14.98(i)] Single moulding

15 mm thick cement plaster 1:4 on the rough side of single or half brick wall. [HSR 15.10]

Painting two coats with synthetic enamel paint in all shades on old wood work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. [HSR 16.5]. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge) (Through Rate)

Distempering with washable oil bound distemper ( of approved manufacture ) two coats on old distempered work. [HSR16.60]. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge) (Through Rate)

Finishing walls with exterior decorative cement based paints such as snowcem Robiacem etc. on new work, two coats go give an even shade. [HSR 16.61] (Through Rate)

Providing two coats of exterior acrylic emulsion paint. (Apex/Ultima of Asian/Dulux). (b) 1st quality. [HSR 16.79(b)]. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge) (Through Rate)

Providing and applying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. [HSR 16.81] (Through Rate)

Providing and fixing aluminium work for doors windows, ventilators and parti-tions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS, 733 and I”S : 1285 fixed with rawlplugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required neoprene felt etc. aluminium sections shall be smooth, rust free straight mitred and jointd mechanically wherever required including cleat angle. Aluminium snap beading for glazing/panclling C.P.brass/stainless steel screws, all complete. [HSR 17.95] + Note-17.96 (II) Fixed portion (Anodised aluminium transparent or dyed to required shade according to IS:1868, min. anodic coating of grade AC 15 Note :- Add Rs. 20/- per Kg. extra if powder coating of 50 micron is done instead of anodizing.

Providing and fixing aluminium work for doors windows, ventilators and parti-tions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS, 733 and I”S : 1285 fixed with rawlplugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required neoprene felt etc. aluminium sections shall be smooth, rust free straight mitred and jointd mechanically wherever required including cleat angle. Aluminium snap beading for glazing/panclling C.P.brass/stainless steel screws, all complete. Shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of PVC/neoprene gasket required including aluminium fitting. [HSR 17.96]+ Note (II) Note :- Add Rs. 20/- per Kg. extra if powder coating of 50 micron is done instead of anodizing.

Providing and fixing 12mm thick pre-laminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 grade I and II in paneling fixed in aluminium doors. Windows shutters and partition frames with C.P. brass/stainless steel screws etc. complete. (b) Pre-laminated particle board with decorative lamination on both side. [HSR 17.97(b)]

Providing and fixing aluminium round shape handle of outer dia 100mm with screws etc. complete. [HSR 17.102(ii)] (ii) Powder coated minimum thickness 50 micron aluminium.

Steel reinforcement TMT steel bar FE-550 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including stairghtening, bending, binding, wastage, overlaps, welded joints, spacer, bars, chairs, stays, hangers and annealed steel wire etc.and placing in position complete in all respect for all heights/depths/storeys/basement etc. (Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. Wastage overlaps, couplings,welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing, shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement).(HSR: 18.22)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). [DSR 10.28]

Providing and fixing in position best indian make (to the approval of the Engineer-in-charge). Indian type orissa or orya water closet suite for sinking into floor, with raised foot treads complete with 100 mm H.C.I. 'P' trap with or without vent as requiered and all other necessary fittings as fully described in item No.30.1 above [HSR 30.2(a) Size 580mm (ii)] White

Extra over items Nos. 30.1 to 30.4 and 30.6 for providing and fixing 15 litres capacity vitreous china high level cistern complete with internal brass fitting instead of 12.5 litres capacity high level C.I. cistern complete (as approved by the Engineer-in-charge)[HSR 30.8(i)]

Providing and fixing in position best indian make (as approved by the Engineer-in-charge) European type water closet suite, syphonic type, Consisting of- [HSR 30.5(b)(i)] (i) Vitreous chinaware syphonic suite with 15 litres capacity matching chinaware cistern and all internal brass fittings complete with 'P'or 'S' trap with or without vent (as approved by the Engineer-in-charge) (ii) One piece seat and lid in hollow back or white plastic fitted with chromium plated hinges and rubber buffers,( to the approval of the Engineer-in-charge) Complete in all respects including cutting and making good the walls and floors.(b)Double trap symphonic W.C. Suite (i) white

Providing and fixing in positon best indian make a range of two urinals flat back or angular lipped front 610 high in viterous china-ware with 5 litre capacity best indian make C.I. automatic flushing cistern with fittings and flush pipe etc. complete as fully described in Item No. 30.25 above[ HSR 30.26(a)Range of two urinals (i) white]

Extra for providing and fixing viterous automatic flushing cistern including fittings and brackets instead of C.I. flushing cistern complete.[HSR 30.37(a) 5 Litres capacity cistern (i)] white

Providing and fixing 25 mm thick marble backs for the different type of urinals.[HSR 30.40(b)(II)(i)] VITREOUS CHINAWARE PARTITION PLATE Small size 680 mm x 330 mm (i) White

Providing and fixing in position best indian make (ordinary) lavatory suites comsisting of:- Lavatory in vitreous chinaware size as given below (to approval of the Engineer-in-charge) including china plug for tap hole where necesssary.R.S. or C.I. brackets for buildings into wall including painting. 32 mm C.P. Brass waste with C.P. brass china and rubber plug. 15mm C.P. Brass screws down pillar tap with jamnuts or coupling best design (as approved by the Engineer-in-charge). All fittings best indian make and; to the approval of the Engineer-in-charge. All brass work chromium plated and complete in all respects including cutting and making good the walls floors and painting of fittings etc.[HSR 30.41(a)(vi)] whtie Size 630mm x 450 mm with one no. tap

Providing and fixing in position best indian make C.P. Brass three tap holes mixer with pop-up-waste instead of one no pillar tap and C.P. waste [HSR 30.46(b)]

Providing and fixing in position best indian make chromium plated brass bottle trap 32 mm dia metre. [HSR 30.50]

Providing and fixing in position best indian make paper holders fixed into wall with C.P. brass screws complete in all respects including cutting and making goods with walls etc.[HSR 30.67(a)] C.P brass

Providing and fixing in position best indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making goods the walls etc.[HSR 30.70(a)(ii)] (a) C.P. Brass (ii) Soap dish small

Providing and fixing in position best indian make bevelled edge 5.5 mm thck mirror mounted on asbestos sheet ground fixed in position by means of 4 Nos. chromium plated brass screws and washers over rubber wshers and rawl plug embedded in the wall or chromium plated brass clamps with C.P. brass screws (as required by hte Engineer-in-charge) complete including cutting and making good the walls etc.[ HSR 30.71(a)(i)] (a) INDIAN MAKE (i) 600 mm x 450 mm

Providing and fixing in position 15 mm i/d C.P brass bib Cocks of best quality (as required by Engineer-in-charge)[HSR 30.75(a)Bib cock long body

( c) Bib cock

Providing and fixing in position C.P brass stop cocks (as Approved by the Engineer-in-charge)[HSR 30.76(a)15 mm stop cock (i)] Stop cook male and female end

Providing and fixing inposition best indian make C.P. brass inlet connetion 15 mm with 375 mmm pipe and C.P. Brass nuts.[HSR 30.83]

Providing & fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. [HSR 30.119] 1000 litre capacity

2000 litre capacity

Extra for providing cut out/opening of required size & shape as per architectds drawings and design for wash basins/kitchen sink in kitchen platform, vanity counters and similar locations in marble/stone/granite work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. compete. [DSR 8.5]

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved muncipal design [DSR 17.30]

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. [DSR 18.8.1] (a) 15mm nominal outer dia pipes

25mm nominal outer dia pipes

Providing and fixing G.I. union in GI pipe including cutting and threading the pipe and making long screws etc. complete. [DSR 18.46.1] (a) 15mm internal diameter of pipelines.

25mm internal diameter of pipelines.

Providing and dixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 meter long with S.S. triangular plate to European type W.C. of quality and make a sapproved by Engineer-in-charge.[DSR 17.16(a)]

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge[DSR 18.53(a)]

Providing and fixing C.P. brass angle valve for basin mixer and geyser points od approved quality conforming to I.S. 8931. 15 mm nominal bore [DSR 18.53.1]

Removing of Malba as collected from the dismantling of toilet including taking out Malba from Ground Floor to dumping yard and then removal by mechanical means. [NS] Note 1 :-In case of any difference in the unit & nomenclature of any of the HSR/DSR items of civil,PH work depicted in this DNIT and that given in HSR,the unit and nomenclature given in HSR shall be applicable. 2. Only reputed make material will be used (Make/brand exhibited in HSR/DSR and exhibited in approved standard documents) as approved by the Engineer-in-charge,while executing various items/work at site.

prashant construction company