Loading…
Loading…
Tender Value
₹4.0 Cr
EMD Value
₹4.0 L
Closing Date
20 Jun 2026, 11:00 am5d left
Renovation/Interior Work Comprising of Civil Works, Electrical Works, HVAC, Fire Alarm Work, Furniture Work, AV/VC Work, IT, etc
NSL/CEO/ICMR/NIT/2026/909
NSL/CEO/ICMR/NIT/2026/909
Open Tender-Domestic
Miscellaneous
New Delhi, Delhi
₹11,800
₹4.0 L
12 Jun 2026
12 Jun 2026
20 Jun 2026
20 Jun 2026
S.No. Description of Works Amount
Amount (DSR, in Rs.)
1 civil and interior work 2,754,651.01 9,894,174.18
Correction factor on DSR @ 0.973 2,680,275.43
GRAND TOTAL (Carried Forward) 12,574,449.61
GRAND TOTAL (Carried Forward) 12,574,449.61
Digitally signed by AMIT
SR. NO. DSR REF. NO. DESCRIPTION UNIT QUANTITY DSR RATE DSR AMOUNT NDSR RATE NDSR AMOUNT
A DISMANTALING
Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per
direction of Engineer-in - charge.
15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) CUM 15.00 2,434.25 36,513.75
Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of
unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.
Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including
loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m
initial lead, for all leads
including all lifts involved.
Providing Pre-constructional anti- termite treatment and creating a chemical barrier to the building by injecting chemical
emulsion of required concentrations under grade slab and Grade beam, all-round the junction of wall and floor, surrounding
of pipes, side walls etc.as per instructions of chemical manufacturer and all as directed. The treatment shall be carried out
strictly in accordance with the technical specification and conforming to IS 6313 or equivalent BS specification. The chemical
to be used as insecticides for the treatment shall be Imidacloprid 30.5 percent SC, dilution per litre of water 2.1 ml (1:476)
strictly in accordance with IS 6313 (Part-2): 2022 or as per manufacturers specification whichever is higher. Chemicals
Concentration, Imidacloprid 30.5 percent SC 0.075%
TOTAL FOR DISMANTALING
B MASONRY AND PLASTER
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat
cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.
11.3.1 40 mm thick with 20 mm nominal size stone aggregate SQM 50.00 614.20 30,710.00
Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry with 150 mm to 300 mm thick with Grade-1 AAC
blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super structure above plinth level up to floor V level
with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per
direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).
Providing and constructing AAC/SIPOROX Block Masonry wall in proper line and level, at all levels in cement mortar 1:4 (1
cement : 4 coarse sand) using standard size of blocks of thicknesses as given below, including all scaffolding, staging, curing,
all lifts, pointing of joints very neatly complete to the satisfaction of the Engineer-in-charge, all labour, hire and fuel charges
for all tools and plants employed etc. complete and as directed. Rate shall include providing Concrete Binders in proportion
1:2:4 (1 cement : 2 Coarse sand : 4 Aggregates), 75mm thick reinforced with 2 nos. of 8 mm dia Fe 500 bars, RCC binders to
be at every 1 metre interval from floor level. The rate to be inclusive of cost of reinforcement and formwork, cover blocks for
reinforcement and all other incidental charges etc., all complete and as directed.The rate to also include closing the gap
between the masonry and RCC beam / slab finished to required slope as directed by the Engineer-in-charge. Note:- The
width of the joints not to exceed 10mm. The rate to include pointing the masonry and using Best quality blocks in such a way
that plaster will not be required.
7 13.2 CEMENT PLASTER :- 15 mm cement plaster on the rough side of single or half brick wall of mix.
8 13.21 Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the per bag of 1836.00 22.1 40,575.60
9 5.22A Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete
Digitally signed by AMIT
5.22A.4 Hot rolled deformed bars kg 190.00 107.85 20,491.50
Providing and fixing removable raised/false access flooring with system
and its components of approved make for different plenum height with
possible height adjustment upto 50 mm, comprising of modular load
bearing floor panels supported on G.I. rectangular stinger frame work
and G.I. Pedestal etc. all complete, as per the architectural drawings, as
specified and as directed by Engineer-in-charge consisting of:
(c) Providing and fixing Access Floor panel of 600x600x32 mm medium
grade Filled Steel anti static high pressure Lamination of 800H grade
(FS800H). Access Floor panel shall be steel welded construction with an
enclosed bottom pan with uniform pattern of 64 hemispherical cones. The
top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm
fused spot welded together (minimum 64 welds in each dome and 20
10 11.54 welds along each flange). The panel should be Corroresist epoxy coated
for lifetime rust protection and cavity formed by the top and bottom plate is
filled with Pyrogrip noncombustible Portland cementitious core mixed with
light weight foaming compound. The access floor shall be factory finished
with Anti-static High Pressure laminate with Non Warp technology upto 1
mm thickness for superior adhesion and Surface flatness within 0.75mm.
The panel is to withstand a Concentrated Load of 363 kgs applied on
area 25 mm x 25 mm without collapse in the centre of the panel which
is placed on four steel blocks. The panel will withstand and Uniformly
Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of
50kg all complete as per the approved manufacturers specification and as
per the direction of Engineer-in-charge. All specification must be printed
on the side of the panel to ensure the quality of the product.
11.54.1 300 mm Finished Floor Height (FFH) Sqm 7.00 5,623.95 39,367.65
Providing and applying Plaster on internal walls, ceilings, columns, beams, etc., to achieve a smooth, even, and level
13 surface, including surface preparation, application, curing (if required), and finishing complete.
TOTAL FOR MASONRY AND PLASTER
C FLOORING, PAVING AND WET WORKS
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the
manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by
16 8.31 Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse SQM 70.00 1,267.95 88,756.50
sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of
matching shade complete.
Grouting the joints of flooring tiles having joints of upto 5 mm width, using epoxy grout mix of 0.70 kg of organic coated filler
17 MR of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per
direction of Engineer-in-charge.
ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish.
Thickness 1.30 to 1.50mm. Designed to conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.
Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less
than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm
11.46 thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting
the joint with white cement & matching pigments etc. complete.
19 11.51 Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of
11.51.1 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc. SQM 15.00 6,603.35 99,050.25
Digitally signed by AMIT
Providing, mixing and installing self levelling compound high quality synthetic resins, special cements and selected fillers so
that, when mixed with water, it produces a free-flowing mortar with self-levelling properties. The mixed mortar can be
applied to a average 10mm thickness in a single pour and can be bulked up to 30 mm with usage aggregates, retaining its
20 MR free-flowing properties Bulk density of powder approx. 1.3 kg/l , Ball Impact Hardness After 1day 6.5 mm, Scratch Hardness SQM 50.00 1,471.80 73,590.11
After 1 day 1.6 mm Compressive Strength 2 After 28 days (min) 20 N/mm ²and free flowing rapid hardening, levelling and
smoothing compound designed to produce a smooth, flat surface when applied to hard, rigid sub-floors such as cement sand
screeds, concrete, etc. strictly following the manufacturere instructions and complete.
Carpet Flooring : Supply of modular carpet of approved model and shade and made with 100% nylon 6/6.6 tufted textured
tiles/ plank of all sizes as approved, stain resistant, anti microbial, and having colour fastness to water, fastness to light,
rubbing fastness and castor chair suitability as per relevant standard for heavy commercial usage, with 100% PVC free
21 MR Backing with having average density 6000 oz/cu. yd. or more,Nominal total thickness of 5.9mm, and Pile weight – 16-18 oz/ SQM 90.00 3,875.02 348,751.70
sq yard. Material shall be CRI GREEN LABEL PLUS certified, and shall have recycled content complying to GRIHA requirement,
including fixing with GRIHA compliant adhesive of approved make, minimum 15 years manufacturer's warrantee, all
complete as per drawings, manufacturer's specifications and direction of Engineer in Charge
ITALIAN MARBLE: Providing and laying machine cut, mirror polished, Italian Marble brass brass inlay stone flooring laid in
required pattern in linear portion of the building all complete as per architectural drawings, with 18mm thick stone slab laid
23 11.51 over 20mm (average) thick base of cement mortar 1: 4 (1 cement: 4 coarse sand) laid and jointed with white cement slurry
@ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including
rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.
11.51.1 18 mm thick Italian Marble stone slab in all colour and shade Sqm 35.00 6,603.35 231,117.25
IPS FLOORING: 52mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12mm thick
24 11.4 cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, Sqm 90.00 978.45 88,060.50
hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of
cement slurry, but excluding the cost of nosing of steps etc. complete.
Supply and Installation of SPC Flooring which is engineered for exceptional performance and long-term durability.
It features a total thickness of 4+1 mm (Herringbone Pattern), including an integrated IXPE underlay that provides
superior sound absorption and enhanced walking comfort. The flooring offers excellent dimensional stability (≤
0.17%) and minimal curling (≤ 2 mm). With a wear layer thickness of no less than +0.3 mm and a density range of
1.98–2.05 g/cc, it ensures outstanding strength, resilience, and surface integrity. The precision locking system
25 MR provides a locking strength of ≥ 2.5 Kn/M, ensuring excellent joint integrity and long-lasting performance. The Sqm 42.00 3,700.00 155,400.00
surface delivers AC6 wear resistance and a refined gloss level of 5–8 GU. The flooring also demonstrates high peel
strength (≥ 90 N) and meets Bfl-S1 fire-resistance standards, ensuring safety, durability, and reliability under
demanding conditions.
TOTAL FOR PAVING & WET WORKS
D PARTITIONS CLADDING AND WOODWORKS
Digitally signed by AMIT
PARTITIONING - Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up
standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285,
fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and
26 21.1.1.1 sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and kg 450.00 530.90 238,905.00
jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass /
stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling
and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron)
PANELLING- Panelling using 12mm thick (±0.5mm) HDHMR fixed on one side on Aluminium Frame 50mm x 25mm x 1.5mm
27 MR as per approved sample and architectural drawings. Aluminium frame to be fixed to walls, floor and RCC Ceiling using SQM 300.00 2,477.47 743,240.00
Providing and fixing decorative laminate wall panelling consisting of Aluminium framework, 12 mm thick HDHMR BOARD
backing and 1.0 mm thick decorative laminate finish including grooves, edge finishing, adhesives, fasteners, labour,
scaffolding and accessories complete as per approved drawings and direction of Engineer-in-Charge.
Providing and cladding of 1.25mm (+/-0.1mm) thick high pressure decorative laminates (conforming to applicable IS:2046-
1995, EN 438-3: 2016, NEMA LD3-2005 quality standard), made from urea free, thermosetting phenolic resins treated Kraft
papers as core material and Amino plastic resin treated decor papers on the finish surface. Product meeting Performance
Resistance to surface wear (350 revolutions),
Resistance to cigarette burns (Rating-Not worse than 3),
Resistance to staining (Rating5),
Resistance to dry heat at 180C (Rating-4),
Resistance to cracking (>4 rating) & Resistance to scratching (>2.0 N) and
Resistance to Color Change-Xenon Arch Lamp (Rating 5/Index 6).
density of 1.35g/cm3 and
other requirements as per applicable standard
Product must fulfil the criteria of Greengard-Gold, GRIHA & GreenPro certification and comply with REACH list of restricted
Surface of laminates accomplice the properties as per classification HGS Grade of the respective standards
Color/Decor, size, and finish of laminates should be agreed and finalized conforming to the product catalog and attributes
committed therein.
The cost to include 4mm thick MDF. Laminate to be pasted on MDF using appropriate adhevise and further fixed to existing
partition/ paneling
Providing and fixingcomplete aslaminate
decorative per instructions of engineer-in-charge.
wall panelling consisting of Aluminium framework, 6 mm thick HDHMR BOARD
backing for 6.0 mm thick lacqured glass finish including grooves, edge finishing, adhesives, fasteners, labour, scaffolding and
accessories complete as per approved drawings and direction of Engineer-in-Charge.
Providing and cladding of 1.25mm (+/-0.1mm) thick high pressure decorative laminates (conforming to applicable IS:2046-
1995, EN 438-3: 2016, NEMA LD3-2005 quality standard), made from urea free, thermosetting phenolic resins treated Kraft
papers as core material and Amino plastic resin treated decor papers on the finish surface. Product meeting Performance
Resistance to surface wear (350 revolutions),
Resistance to cigarette burns (Rating-Not worse than 3),
MR Resistance to staining (Rating5), SQM 20.00 5,250.00 105,000.00
Resistance to dry heat at 180C (Rating-4),
Resistance to cracking (>4 rating) & Resistance to scratching (>2.0 N) and
Resistance to Color Change-Xenon Arch Lamp (Rating 5/Index 6).
density of 1.35g/cm3 and
other requirements as per applicable standard
Product must fulfil the criteria of Greengard-Gold, GRIHA & GreenPro certification and comply with REACH list of restricted
Surface of laminates accomplice the properties as per classification HGS Grade of the respective standards
Color/Decor, size, and finish of laminates should be agreed and finalized conforming to the product catalog and attributes
Digitally signed by AMIT
INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48
29 12.62 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall wirh screw, rawel plug & washers and held and in SQM 450.00 322.50 145,125.00
position by criss cossing GI wire etc. complete as per directions of Engineer-in-Charge.
MR Providing and fixing frosted translucent cast PVC self-adhesive vinyl film (or equivalent) with special CRYSTAL-effect finish to Sqm 29.00 1725.00 50,025.00
Fluted Wall Paneling
Providing and fixing decorative Charcoal Fluted Wall Panels of size 150 mm (6") wide × 3000 mm (10'-0") high, manufactured from high-
density Polystyrene (PS) / Charcoal Composite material, having minimum thickness of 12-24 mm, with prefinished wood grain texture
and matte finish. Panels shall be fixed vertically over prepared plywood/HDHMR backing using approved polymer adhesive and
31 concealed fasteners wherever required, including cutting, edge finishing, grooves, alignment, wastage, scaffolding, labour, tools and SQM 40.00 4,500.00 180,000.00
tackles complete as per approved design and direction of Architect/Engineer-in-charge.
Providing and fixing CNC cut acoustic PET panels of 12 mm thickness (± 4 mm), density 2400 GSM, manufactured from 100%
polyester fibre with minimum 70% recycled content, machine CNC cut as per approved architectural/design pattern, panel
size up to 2800 x 1200 mm, moisture resistant, non-toxic, fire retardant complying with ASTM E84 Class A, BS 476 Part 6 & 7,
ASTM D2859, NRC up to 0.70, complete with necessary adhesive, mechanical fixing arrangement, templates, cutting, edge
finishing, scaffolding, labour, transportation and all incidental works complete as directed by Engineer-in-Charge.
The product should be 100% make in india and resistance to fungal growth As Per ASTM C 518.
OEM must have own manufacturing plant along with ISO CERTIFICATIONS- complying to- IGBC Membership,
ISO 14184-2 (Release formaldhyde)
ISO 9001 (Quality Mangement System)
ISO 14001 (Environmental Management System)
ISO 45001 (Ocupational helth & safety management system) The cost to include all required
adhesive/ fixing arrangements complete as per instructions of engineer-in-charge.
Providing & fixing decorative Poly décor fabric Wall Paper (on walls and ceiling) of weight 475 g /sqm as per approved
shade & design including prepration of surface with 2 coats of Nubin Glue based epoxy quote.
Providing and fixing of 4 mm/6 mm/8 mm thick annealed GRIHA rated lacquered glass manufactured industrially by curtain
coating process with PU lacquer (50 micron thick), opaque (if viewed against a support wall) conforming to EN 16477
standards for back painted glass , of approved color by Architect/ Client fixed with compatible Silicone having Shear Bond
Strength (Dry, 24 hours), greater than 450 kpa and tack free time of 10 to 30 mins compatible for installation of mirror and
lacquered glass / Foam based double sided adhesive tape for instantaneous adhesion, compatible with mirror and lacquered
glass having Shear bond strength (Dry, 15 mins) of 250 to 350 kpa) on a perfectly leveled 12mm thick water proof marine
plywood / MDF / Mineral fibre board which is mounted on the RCC wall/any other structure. The contractor should submit
test reports for backpainted glass from manufacturer - High humidity Resistance (conforms to BS EN 1036 1999); Color
fastness ISO 105B02 standard & Mechanical Resistance ISO 7784 ( Taber Abrasion test ) ISO 2409 ( Cross Hatch Test )
standard The manufactured backpainted glass should be environmentally friendly (no lead, no arsenic, no copper,
noformaldehyde); appropriate recycled content (12% post industrial / 6% post consumer); compressive strenght (1000 MPa)
& tensile strenght (40 MPa),same as float glass
LAMINATED STORAGE CABINET FOR GENERAL STORAGE- Out of 18mm thick HDHMR Board finished using 1mm thick
laminate. The storage shall be complete with all hinges, drawer glides and hardware from approved make. All internal
35 M.R. surfaces to be completed using balancing laminate. Including brass D-type handles for shutters and recessed type handles for SQM 5.00 10,450.00 52,250.00
drawers. Storage to be of all heights as per design. Storage shutters to be made in solid laminate/ glass as per design and
Digitally signed by AMIT
DOUBLE GLAZED GLASS PARTITION SYSTEM WITH GLASS COMBINATION OF 10MM + AIRGAP + 10MM
TOUGHENED GLASS): Supply & Installation of Aluminum profile with top & bottom profiles of size 82mm x 38mm in Natural
Anodized / Black finish. Partition sides to be fixed with mullion and it's covers should be easily accesible while removal of
glass, if & when required. Glass to be fixed with suitable EPDM gaskets for insertion of combination of 10mm thick clear
toughened glass + 58 to 62 mm Air Gap + 10 mm thick clear Toughened Glass. Glass should not placed directly on profiles
36 for giving more strength. It should be placed on aluminium spacer profiles and spacers should be covered with cover 255,450.00
profiles. Partition Glass joineries consists of two-way Polycarbonate I-profiles, 90 Degree Polycarbonate L-Junction and
Polycarbonate T-Junction profiles. Polycarbonate profile joineries to be fixed with double sided adhesive tape & profiles to
be inserted in the joint instead of sealing it with sealants. Polycarbonate profiles to be used to give continuity glass effect.
Hardware for fixing profiles to be used as per manufacturer standard. Costs should be inclusive of necessary Hardware for
fixing of profiles & installation charges.
SUB TOTAL OF PARTITIONS CLADDING AND WOODWORKS
E FALSE CEILING
GYPBOARD CEILING :- Providing and fixing false ceiling at all height including providing and fixing of frame work made of
special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as
per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm
centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other
flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other
end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to
centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of
10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with
connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5
mm thick 27 mm high having flanges of 20 mm and 30 mm long.
Including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing
compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two
coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for
light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings,
specification and direction of the Engineer in Charge but excluding the cost of painting with :
12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) SQM 140.00 1,355.80 189,812.00
Suspended Curved acoustic ceiling - Providing and Fixing Suspended acoustic ceiling out of 12mm per panels 300mm
High cut in curved profile placed in criss-cross panels as shown in the Visual. Cost to include the necessary
39 Suspensions/Hardware required for the ceiling all complete. Basic rate of 12mm th. Acoustic sheet with Installation &
CNC cutting area to be measured and certified for the payment.
Providing and fixing circular stretch ceiling system comprising premium PVC stretch membrane fixed on aluminium harpoon profile
with necessary GI framework, suspension system, edge detailing, cut-outs for services, accessories, labour, scaffolding and all
incidental works complete as per approved drawings and direction of Engineer-in-Charge. ₹8,000.00
Digitally signed by AMIT
PERFORATED METAL GRILL CEILING WITH INTEGRATED LIGHT: Providing & Fixing of KCS Mineral Fibre Acoustical
Suspended Ceiling in Techzone System with 300*1200mm thick DUNEMAX 20MM Tegular 15 BE Edge Field Panel Tiles &
Metal Plain Tech Panels where ever needed in 1200*150*15mm.
The item shall also include integration of continuous linear LED light fixtures (recessed or surface-mounted within ceiling
modules), including necessary cut-outs, alignment, and coordination provisions.
The rate includes all materials, labour, tools, scaffolding and making good the ceiling surface complete.
Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and
pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ≥ 85%, Thermal Conductivity k = 0.052 -
0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizont al level suspended on interlocking T-Grid of hot
dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm
of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of
42 26.27.2 length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item Sqm 10 2,671.20 26,712.00
(galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to
1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The
system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of
0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall
S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with
polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of
TRAP DOOR :- Providing & fixing Access Panel of size mentioned below having - 1. Outer aluminium frame - thickness :
1.5mm ( plus 0.2mm thick powder coating) Material : ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm
thick powder coating) Material : ENAW6063. 3. Corner fittings, inner frame - material: Hot dipped galvanized steel plate
Thickness 2.0mm, with zinc Coating of 200g. 4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate
43 MR Thickness 2.0mm, with zinc Coating of 200g. 5. 12mm plasterboard ( Knauf Brand) Type: moisture resistant ( MR) in green
plasterboard liner. 6. Screw ( self - drilling black phosphate ) - Material: mild steel C1018 - 1022. 7. Sealing strip, width,
thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock ( spring catch/ catch lock ) - Type of lock: touch latch, Material of
lock: plastic ABS, cold rolled steel Q235. 9. Hinge - Thickness : 4.0mm, Length: 82mm; Material: SS2172 ( cold drawn steel
wire ). 10. Powder coating - Color: white, RAL 9010/ or as approved complete as per instructions of engineer-in-charge.
1200x2400 (cfm trapdoor as/site) EACH 1.00 12,000.00 12,000.00
CEILING PELMETS :- Providing and fixed pelmet of overall size 150mmx150mm and made hardwood framings hung from
44 MR ceiling @1000mm centre to centre with 2 nos of 6mm thk. Commercial ply on vertical & 12mm thk. Commercial ply on RMT 80.00 1,019.05 81,524.06
horizontal surface (straight & curved). Inclusive of finishing in Paint.
Providing the gypsum single sided cove of 150mm x 150mm having a facia of 75mm to macth the specifications same as
gypsum ceiling.
Digitally signed by AMIT
GYPSUM BOARD VERTICAL BAND- upto100mm high gypsum band all round the mineral fibre/ gypsum ceiling. In order to
45 MR make the Mineral Fiber/ gypsum ceiling higher than the Gypsum Ceiling by upto 100mm as per drawings. (visible surface of RMT 40.00 290.00 11,600.00
gypsum band to not exceed 100mm) including plastic emulsion paint.
HDHMR fluted baffle spiral false ceiling : Providing, fabricating, supplying and fixing of decorative suspended ceiling system
comprising custom-designed curved/ripple profile ceiling made out of minimum 1.2 mm thick powder coated HDHMR/GI
slats/ panels of approved shade and finish, arranged in continuous wave/rib pattern as per approved architectural drawing
and site mock-up, suspended from RCC slab/ ceiling using required GI/aluminium suspension system consisting of threaded
rods of minimum 8 mm dia, dash fasteners, cleats, adjustable hangers, suspension brackets, perimeter channels, primary
runners, secondary support members, stiffeners, bracing members and all necessary connecting hardware complete. The
slats/panels shall be factory-finished with PU/PVDF/powder coating, edge-bent for rigidity, and fixed with concealed
clips/mechanical locking arrangement maintaining uniform spacing, alignment and curvature throughout. The work shall
include providing and fixing concealed linear LED profile/channel lighting at wall junctions including aluminium extruded
housing, diffuser, drivers, connectors and all mounting accessories integrated within the ceiling profile, complete as per
approved lighting scheme. The ceiling system shall be designed to withstand sagging, vibration and thermal movement and
shall include provision for access panels, cut-outs for light fixtures, sprinklers, smoke detectors, speakers, HVAC diffusers and
other MEP services wherever required. Approximate panel/slat dimensions shall be 75–150 mm depth with variable spacing
of 20–50 mm and suspended drop ranging from 300–900 mm below soffit level as per approved design. The rate shall
include all materials, labour, scaffolding, templates, bending/forming, fabrication, transportation, testing, installation, touch-
up painting, wastage, coordination with MEP services and all complete works required for proper execution to the
satisfaction of Engineer-in-Charge. Measurement shall be taken on plan area basis in square metres.HDHMR fluted baffle
spiral false ceiling
SUB TOTAL OF CEILING
Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet
(zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes
47 9.136 fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame Metre 12.48 1,709.25 21,331.44
and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer
etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).
Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II),
tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of
vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less
than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved
make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge
(panneling to be paid for separately).
Digitally signed by AMIT
Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6
mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at
distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder
coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per
NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 60
minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of insulation (EI20). The
manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E,
EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in
accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible.
The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.
50 Supply & Installation of (44x64mm) Door Frame with Stile doors with sound reduction property upto STC 31dB
Door Frame: The Door opening shall be formed by custom aluminium door frames in Black Anodized Finish It should have
Deko door frame of size 44 x 64mm.
Shutter: Providing of 40mm thick Stile Shutter. The width of Door Frame will be 70mm with provisions for inserting glass and
the glass used in the system shall be 10mm toughened Glass with necessary acoustic gaskets.
Hardware Black Powder Coated Finish or as approved
Hardware for Single Leaf: Flush hinges - 4 nos, 800mm D- Handle and dead lock with Lever handle, Concealed Door Closer
with hold open unit, Door Stopper, -X-Bottom Seal.
Hardware for Double Leaf: Flush hinges- 8 nos, Geze 35mm Back Set Narrow Stile Dead lock with 300mm D Type Offset
handle, TS3000V SLD Arm Door Closer with hold open unit, Door Stopper, X-Bottom Seal, 600mm Long Tower Bolt, Astragal
Double Door Seal-3000mm-1 No's
Supply and installation of Deko Aluminium 55mm 'J' Type Endcap on both sides of Gypsum Partition ( This Endcap is suitable
upto maximum 110mm wall thickness)
50.2 Double Leaf Door Size : 1500 x 2400mm Nos 3.00 290,000.00 870,000.00
Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in
51 9.1 position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for
9.1.1 Second class teak wood CUM 0.15 142,949.70 21,442.46
SUB TOTAL OF DOORS
G FINISHES & MISCELLANEOUS
56 13.48 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :
Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10
Digitally signed by AMIT
Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and
smooth complete.
Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with
following process in the sequence as detailed below:
1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying
two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12
3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer
and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill
all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is
done this surface is further allowed to dry for 12 hrs.
4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in
required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is
further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine
clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat
to be done in 1 or 2 layers without gap of time.)
59 MR Same as above but for moulding/ cornices for all sizes RMT 490.00 415.00 203,350.00
Preparation of complete set of civil and interior finishing drawings including details. A qualified professional for the purpose
shall be appointed after due appproval from Engineer In Charge.
WINDOW BLINDS : Providing & supplying of fabric venetian Window Blinds as per the approved sample, consisting of 3"
vane size having head rail, rotator rail and bottom rail made of aluminium powder coated and provided in standard natural
white color. The rolling tube should be made up of aluminium alloy from. The head rail dimensions should be of suitable size
according to the length of head rail and space available and finished with fabric cover matching with the louver fabric. The
61 cassette should conceal the working mechanism rotary-clutch. (White polycarbonate spring tempered rotary clutch which
raises), lower and tilts the blinds. White polycarbonate limit assemblies control vane over-rotation, located on either side of
individual blinds. All parts, components & hardware are in approved shade as per direction of Engineer-incharge.
BLACK FINISH ALUMINIUM U PROFILE FOR ACOUSTIC PANELS / BAFFLES
Providing and fixing BAUX approved aluminium U-profile edge trim/frame profile in premium matt black powder-
coated/anodized finish for acoustic wall panels, ceiling baffles and acoustic installations. Profile shall be extruded aluminium
alloy 6063-T5/T6, minimum 1.5 mm thick, suitable for accommodating acoustic panel thickness as per manufacturer RM 1,500.00
recommendations. The profile shall have factory-finished black coating, corrosion resistant, with concealed fixing
arrangement including brackets, screws, anchors, joining cleats, connectors and all accessories required for complete
THROW RUGS: Providing and laying Rugs Broadlooms in Hand Tufted to Customised design of approved size in locations as
directed. The cost shall include all adhesive necessary items required for installation.
Digitally signed by AMIT
Providing and fixing decorative column paneling comprising 50 mm × 50 mm GI framework made out of 1.6 mm thick GI
sections fixed to floor, ceiling and existing column with suitable fasteners, providing and fixing 12 mm BWR grade plywood
63 over GI framework, finished with 1.0 mm thick approved shade decorative laminate on exposed surfaces including adhesive, SQM 80.00 2,500.00 200,000.00
edge finishing, screws, necessary backing supports, cutting, wastage, scaffolding, labour, transportation and all incidental
works complete as per drawings and direction of Engineer-in-Charge.
64 Signage Specifications
Providing and fixing signage of SS sheet of 304 grade as per approved size, sample and fixed to proposed area with
appropriate arrangement/ materials of approved make complete in all respect, as per approved drawings and direction of
Engineer-InCharge. (font and size used as per drawing & approval.)
SIGNAGE TO BE MADE WITH LAMINATE / VENEER SURFACE OR GLASS & TOP OF CHAMPAGNE METAL PROJECTING OR
BLACK TEX ON 3M VINYL PASTED ON FROSTED GLASS of board size 150x170 mm (word or sentence language to be provided Each 50.00 1,520.00 76,000.00
by Client department)
SIGNAGE TO BE MADE WITH 4MM THK CHAMPAGNE FINISH SS LETTERING / FIGURE CUT TO DESIGN & PASTED OVER
EXISTING WALL of board size 200x200 mm (word or sentence language to be provided by Client department) Each 10.00 9,031.00 90,310.00
CUSTOMISED JOINERY UNIT: Supply and fixing of full height storage units with credenza in Conference Room(upto
600mm depth) made out of 18mm plywood finished with approved .8mm laminate on the inside and outside. Hardware used
of Hettich make.Complete as per the direction of Engineer in charge.
Customised Overhead Storage in corridor fixed with L-angle And cove lights profile .
Display Shelf in Reception Area and Reception Back Wooden Partition with Planter .
Dry Pantry Counter
Triangular Low Height Storage With Planter = 02 number
65 MR Corian Marble Reception Counter SQM 120 -- ₹18,945.00 ₹22,73,400.00
providing and fixing acrylic solid surface as per direction of engineer in charge
SUB TOTAL OF FINISHES 2,754,651.01 9,894,174.18
Digitally signed by AMIT
DSR Rate after GST NDSR Rate
Multiplication factor@
Sr.No DSR No. Description Unit Quantity DSR Rate DSR Amount NDSR Amount
A CHAPTER-1: VARIABLE REFRIGERANT FLOW SYSTEM
1.a DRS 2025 VRF/VRV OUTDOOR UNIT
Supply, Installation, Testing & Commissioning of Modular type Variable
Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units
suitable for cooling/heating having 100% hermetically sealed inverter type
twin Rotary/Scroll Compressor(s),minimum two compressors (with
individual separate PCB) for above 14HP modules, microprocessor based
Controller, top discharge type condensing unit(s), with R-410-A Refrigerant
or equivalent, vibration Isolators with suitable foundation etc. complete as
required. To have better efficiency condenser fan shall be capable to operate
at different speed with respect to load. The unit shall deliver the rated
capacity and in confirmation as per IS 18728:2024 and CPWD
Specifications and work even at 50°C ambient temperature without tripping.
The system shall be able to deliver 100% of the rated capacity upto 39
Degree Celcius.The unit shall be suitable to work on 400V +/- 10%, 3 Phase,
31.1 50Hz AC power supply and BMS compatible. The unit shall be filled with first
charge of the refrigerant and ready for use as required. The condenser
should be coated with a hydrophilic film to prevent water accumulation on the
surface of the heat exchanger, enhance water dispersion, and reduce the
risk of degradation, thereby improving overall performance and durability.
The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as
per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as
below and complete as per CPWD specification, connections, inter
connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity >
40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC
Digitally signed by AMIT
Proposed Office for AQM at New Delhi SINGH
Architect: ARGROUP
Supply, Installation, Testing and Commissioning of following minimum
capacity 4 way Cassette Type Indoor ceiling mounted unit equipped with
synthetic washable media pre-filter, fan section with low noise fan / dynamically
balanced blower, multispeed motor, coil section with DX Copper coil, electronic
expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration
Isolation, Corded remote control etc., suitable for operation on single phase 230
V ± 10%, 50Hz AC supply, complete, as required. The Indoor units must shut down
upon receiving a singal from the
BMS System/Fire Signals. The system shall be capable to adjust air flow as
per room requirement in auto mode. The cooling capacity of indoor unit will be
at air inlet conditions of 27 Degree C DB and 19 Degree C WB
temperature. (Make will be same as of Outdoor)
4-Way Cassette type
HI - WALLSPLIT SYSTEMS
Supplying, Installation, Testing and Commissioning of following minimum
capacity High wall type Indoor unit equipped with and comfort washable
synthetic media prefilter, fan section with low noise fan/dynamically balanced
blower, multispeed motor, coil section with DX copper coil,
electronic expansion valve, outer cabinet, cord less remote control, drain pan,
necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single
31.8 phase AC supply, complete as required. The Indoor units must shut down upon
receiving a singal from the BMS System/Fire Singnals. The system shall be
capable to adjust air flow as per room requirement automatically. The cooling
capacity of indoor unit will be at air inlet conditions of 27 0C DB and 19 0C WB
temperature. (Make will be same as of Outdoor)
1.b.3 MR Corded Remote controls Nos 1 2500 2500
1.b.4 MR Communication cable (1.5 sqmm X 2 Core) Rmt 150 55 8250
Supply, installation, testing and commissioning of MS fabricated outdoor unit
stand for placing outdoor unit of VRV system. The stand shall be manufactured
from MS C channel of minimum 3-4 mm thick. It shall be finished with enamel
paint as per client/architect approval.
2.0 REFRIGERANT PIPING
Digitally signed by AMIT
Proposed Office for AQM at New Delhi SINGH
Architect: ARGROUP
Supply, Installation, testing and commissioning including vaccumiazation
and Nitrogen testing of following nominal sizes of soft/hard drawn copper
refrigerant piping for VRV/VRF system, complete with fittings, with suitable
adjustable ring type hanger supports, jointing/brazing including accessories,
insulated with XPLE Class-O tubular insulation/with Class-O closed cell
DSR 2025 elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation
VRF/VRV as given below for Suction and Liquid lines, all accessories as per
specifications etc. as required :
31.14.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 50 256.0 12800
31.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 30 346.0 10380
31.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 30 487.0 14610
31.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 30 615.0 18450
31.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 40 739.0 29560
31.14.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 20 904.0 18080
31.14.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 20 1068.0 21360
31.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 20 1157.0 23140
31.14.9 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 20 1222.0 24440
31.14.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 25 1286.0 32150
31.13 Supply, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be
of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUs
31.13.1 Indoor Units Each 5 4535.0 22675
31.13.2 Outdoor Multi Joint Each 2 8098.0 16196
CABLE TRAY FOR REFRIGERANT PIPING
Supplying and installing of following size of perforated hot dip galvanized G.I
cable tray with perforations not more than 17.5%, in convenient sections, joined
4.6 with connectors, suspended from ceiling with G.I suspenders including bolts and
nuts, etc. for carrying refrigerant pipe in outdoor application as required.
3.1. 4.6.10 450 mm width X 62.5 mm depth X 2.0 mm thickness Rmt 150 1713.0 256950
3.2 4.6.3 225mm width x 50 mm depth x 1.6 mm thickness Rmt 50 991.0 49550
4.0 CONDENSATE DRAIN UPVC PIPE
Supply, installation, testing and commissioning of uPVC Pipe ,complete with
fittings, supports,U trap arrangement,Clean Plug with 6mm nitrile insulation and
accessories as per specifications, drawings.
23.0 MR CEILING MOUNTED EXHAUST FANS
Digitally signed by AMIT
Proposed Office for AQM at New Delhi SINGH
Architect: ARGROUP
Supply , installation , testing and commissoning , of ceiling mounted inline fans
complete with direct driven centrifugal fan , direct drive arrangement , heavy
gauge sheet metal casing , rubber isolator mounts and other accessories.The
fan shall be complete in all respect and should match the specification
,Drawings and Schedule. Inline fans shall be of following capacities.
G CHAPTER-7: ELECTRICAL WORK
Supply, installation, testing and commissioning of indoor/outdoor floor mounted/
wall mounted, IP43/IP65, IS 61439 factory built, modular, sectionalised,
compartmentalized, extendable type LT cubicle panel of suitable size suitable
for operation on 433/415 volts, 50 Hz AC 3 phase 4 wire supply system fabricated
from CRCA sheet steel of 2mm thick for frame work and covers, 3mm thick for
gland plates with stiffeners wherever required, having vibration free structure
chemically treated with seven tank process or better before painting for surface
treatment and powder coated in approved shade, with suitable electrolytic
grade high conductivity bus bars extensible, DMC/ SMC (whichever is superior)
25.0 bus bar supports, with short circuit withstand capacity as mentioned ,bottom
base channel of section not less than 100mmX 50mmX 5 mm thick, fabrication
shall be done in transportable sections, entire panel shall have a common earth
bar of required size at the rear with 2 Nos. earth stud, connections and
interconnection with solid conductor wires / copper strips, neutral links, control
wiring with 1.5 sqmm. & 2.5sqmm. PVC insulated FRLS copper conductor S/C
cable for voltage & current respectively, including providing and fixing following
switch gears and as per schedules ,technical specifications etc.complete as
415V, 50Hz, 160A, 4P, 25kA for 1 sec rated microprocessor based MCCB with
inbuilt LSIG protection - 1 Nos.
Metering (1 No.)
Multifunction meter with inbuilt selector switch for measurement of current,
voltage, power factor, KVA, kVAh, KVArh, KVAR, frequency, ,KWHr (both line and
phase) complete as per specifications
Indication lamps
LED type phase indication lamps suitable for 230V,50Hz AC (red, yellow, blue) - 1
LED type Indication lamps for breaker, suitable for 230V,50Hz AC supply (on, off,
Busbar : 15VA, CL-1 current transformer for metering
Busbar (1 Set - 4P + E)
Busbar made up of electrolytic grade high conductivity aluminium in
rectangular cross section and suitable for 415V, FP, 50 Hz, 300 A, 25 kA for 1 sec
of required length and cross sectional area.
5Nos. 415V, 50Hz,63A, 4P, 10 kA MCB.
Digitally signed by AMIT
Proposed Office for AQM at New Delhi SINGH
Architect: ARGROUP
Supply,installation,testing and commissioning of 63A 4P,Isolator , heavy duty solid
neutral link in a sheet steel enclosure with required arrangement for incoming
and outgoing cable complete as required.(Weather Proof)
Supply,installation,testing and commissioning of 40A 4P,Isolator , heavy duty solid
neutral link in a sheet steel enclosure with required arrangement for incoming
and outgoing cable complete as required.(Weather Proof)
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. 37,750.00
pipe from earth electrode including connection with G.I. nut,
26.1. 5.11 bolt, spring, washer excavation and re-filling etc. as required.Providing and fixing Metre 50 755
25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
Providing and laying earth connection from earth electrode with 6 SWG dia G.I. 6,260.00
26.2 5.12 Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. Metre 20 313
thimble excavation and re-filling as required.
LT CABLE AND TERMINATION
Supplying, unloading, storing , laying, testing and commissioning of following sizes
of 1.1 kV grade XLPE insulated, FRLS (Heavy duty) Aluminium/copper conductor
armoured/unarmored cables suitable for working voltage upto and including
1100 Volts, laid and tied on existing overhead cable trays; or buried
underground or laid and tied over MS supports in masonry trenches including
providing MS supports and clamps for fixing to supports in an approved manner,
providing fire retardant sealant where required complete as required and as per
specifications. Circuit identification tag should be attached with the concerned
cable alongwith the test report of following sizes of cable to be submitted by the
contractor at the time of delivery of material at site. (Cable length may increse
as per existing panel location).
Supplying and making end termination with brass compression gland and
28.0 11.1 aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE
aluminium conductor cable of 1.1 KV grade as required.
Supplying following 1.1kV grade, XLPE insulated, FRLS type control
cables,suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath,
29.0 outer sheath provided with FRLS insulation and with all components as
mentioned in BOQ, specifications and schedule, complete as required.
29.1 MR 2C X 1.5 sqmm copper conductor Metre 20 85 1,700
29.2 MR 2C X 2.5 sqmm copper conductor Metre 40 125 5,000
Digitally signed by AMIT
Proposed Office for AQM at New Delhi SINGH
Architect: ARGROUP
Supplying and making end termination with single compression brass gland and
lugs for following size of 1.1kV grade, XLPE insulated, FRLS type control
cables,suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath,
outer sheath provided with FRLS insulation and with all components as
30.0 mentioned in BOQ, specifications and schedule, complete as required. The cost
shall include the cost of crimping and all tools and accessories required to
complete the job in full respect.
Note : Al lugs shall be used for Al cable and cu lugs shall be used for copper
30.1 MR 2C X 1.5 sqmm copper conductor Each 2 250 500
30.2 MR 2C X 2.5 sqmm copper conductor Each 2 300 600
CABLE MANAGEMENT
31.0 SOCKET OUTLET POINT WIRING
Wiring including termination for 6 amp socket outlet point with 3 x 2.5 sq. mm
PVC insulated FRLS copper conductor wires in concealed/exposed 1.6 mm thick
31.1 MR in MS conduits including providing 6 amp switch,3 pin 6A shuttered Nos 5 1,750 8,750
socket,anodised MS box for housing switches sockets, approved White
Polycarbonate modular cover plate and earthing.
Wiring including termination for 16 amp power socket outlet points with 3 x 4 sq.
mm PVC insulated FRLS copper conductor wires for the 16 amp socket outlet
with 3 x 4 sq. mm PVC insulated FRLS copper conductor wires for the second
outlet of 650/1100 Volts grade in concealed/exposed 1.6 mm thick in MS
31.2 MR conduits as called for including providing 16 amp flush type combined 6 pin Set 5 3,500 17,500
shuttered sockets and switches, anodised MS outlet boxes for 16 A 6 pin sockets
and switches,approved White Polycarbonate modular cover plate and
TOTAL HVAC WORK AMOUNT 1,565,756.37 281,800.00
Digitally signed by AMIT
Proposed Office for AQM at New Delhi SINGH
Architect: ARGROUP
HVAC Low Side Boq ICMR KIDWAI, DELHI
S.No DSR 2025 DESCRIPTION
No./ MR Unit Bill Qty Rate DSR Amount NDSR Amount
SUB-HEAD 'A' - EQUIPMENT
1 MR Air Handling Unit
Dismentling & ReShifting & Installation, testing and commissioning of double skin
airhandling unit ceiling suspended type complete with double skin housing with EFF-1 Nos 1 ₹53,100.00 ₹53,100.00
motor, plug fan, cooling coil, filters.
2 MR Starter Panel
Supply, installation, testing and commissioning of AHU Starter Panel for AHU Nos 1 ₹64,900.00 ₹64,900.00
complete with wiring etc.
Supply, installation, testing and commissioning of INLINE FAN complete with wiring Nos 1 ₹19,470.00 ₹19,470.00
4 INSULATED CHILLED WATER PIPING (Nitrile rubber insulation)
31.2 Supplying, laying/ fixing, testing and commissioning of following nominal sizes of
chilled water piping inside the building (with necessary clamps, vibration isolators and
fittings but excluding valves, strainers, gauges etc.) duly insulated with following
closed cell elastomeric nitrile rubber of minimum 45 Kg / cu m density, thermal
conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation
applied by suitable adhesive complete including repairing of damage to building etc.
as per specifications and as
required complete in all respect. Note:-The Pipes of sizes 150mm & below shall be
M.S. 'C' class as per IS : 1239 and pipes size above150mm shall be welded black
steel pipe heavy classas per IS: 3589, from minimum 6.35mm thick M.S.Sheet for
pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm
30.2.11 50mm dia(32 mm thick insulation) Rmt. 30 ₹1,510.00 ₹45,300.00
Supply, installation, testing and commissioning of Valves, Strainers of following sizes
duly insulated same as given for CHW pipe. as per specifications and drawings.
5.1 SITC of 2/3way motorised valve complete with actuator, valve, power supply & wired
type thermostate
BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring
PN 16 pressure rating for chilled water/hot eater circulation as specified
Digitally signed by AMIT
30.7.4 Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled /
hot water circulation including insulation as specified.
BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged
construction with EPDM coated disc with long pitch with protected out pipe insulation &
PN 16 pressure rating for chilled / hot water circulation as specified.
30.8 Supply, installation, testing and commissioning of Pressure Gauzes 4" dia Round type
complete with Syphon & fitting
30.9 Supply, installation, testing and commissioning of Temperature Gauzes 6" vertical type
complete with Syphon & fitting
6 MR Drain Piping
Supplying, laying, fixing, testing & commissioning of GI class 'B' pipes conforming to
IS: 1239 (Part-1, 1990) complete with all necessary fittings such as elbows, tees,
reducers etc and supports such as clamps etc. complete .Condensate drain pipe
should be complete insulation of 9 mm Nitrile.
25mm dia GI pipes ('B' class, for condensate drain) Rmt. 6 ₹1,475.00 ₹8,850.00
7 30.12 DUCTING, GRILLS,DIFFUSER AND INSULATION
Supplying, installation, balancing and commissioning of factory fabricated GSS sheet
metal rectangular/ round ducting complete with neoprene rubber gaskets, elbows,
splitter dampers, vanes, hangers, supports, bends, transitions, reducers, end caps,
collars etc as required complete in all respect in
Thickness 0.63 mm sheet
Thickness 0.80 mm sheet
Thickness 1.00 mm sheet
8 MR Insulation
Supply and installation of fire retardant duct thermal Insulation from inside duly from
factory (13 mm thick) applied with SR 505.
9 MR Duct Acoustic Lining
Supply & installation of duct acoustic lining with fibre glass insulation of density 32
kg/m3 covered with 26 Ga perforated Al. sheet with nuts and bolts complete as per
standards, requirement and drawings.
Digitally signed by AMIT
10 Grill / Diffuser
Supply, installation, testing and commissioning of aluminium powder coated grills/
diffusers as per specifications and drawings.
30.15 Supplying, Fixing, installation, testing and commissioning of powder coated extruded
aluminium Supply Air Grills with aluminium volume control dampers in confirmation to
SMACNA/IS and as per specifications complete etc. as required.
30.17 Supplying, Fixing, installation, testing and commissioning of supply air diffusers of
powder coated aluminium with aluminium volume control dampers with anti smudge
ring & removable core in confirmation to SMACNA/IS and as per specifications
complete etc. as required.
11 MR Collar Damper
Supply, installation, testing and commissioning of Alu. Collar Damper (supply vents
12 MR Canvas Connection Nos 1 ₹2,360.00 ₹2,360.00
13 MR Volume Control Damper (Duct Damper)
Supply & installation of extruded aluminium volume control damper with blades,
adjustable lever, frame etc. as per specifications and drawings.
Digitally signed by AMIT
Electrical Summary
SUB HEAD DSR AMOUNT (Rs.) NDSR AMOUNT (Rs.)
1 DISTRIBUTION BOARD Rs. 61,500.00 Rs. 151,417.00
3 LIGHTING FIXTURES Rs. 3,183,943.06
4 CABLE TRAY.& RACE WAY. Rs. 108,745.00 Rs. 190,570.38
6 FIRE ALARM & PA SYSTEM Rs. 1,306,431.00 Rs. -
GRAND TOTAL Rs. 7,658,105.43
GRAND TOTAL Rs. 7,658,105.43
Digitally signed by AMIT
Interior/Fitout works of Office Space of ICMR at PLate A (Rear Side), Office Block -3, Ground Floor, East Kidwai Nagar, New Delhi
S.No Description Unit Qty Rate MR Amount DSR Amount
A DISTRIBUTION BOARD
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on
surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections,
powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
2.3.3 8 way , Double door Each 2 2773.00 5,546.00
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board,
415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,
interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)
Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution
board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common
2.5 neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : 0.00
Vertical type MCB TPDB is normally used where 3 phase outlets are required.)
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for
2.1 inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning 0.00
etc. as required.
Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with
connections, testing and commissioning etc. as required.
Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit
2.14 breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with 0.00
connections, testing and commissioning etc. as required.
Supplying and fixing following rating, 240 volts, "C" curve, miniattlre circuit breaker suitable for lnductive loads
of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as 0.00
1.21 Supplying and fixing of following sizes medium class PVC conduit aong with accessories in surface/ recess
including cutting the wall and making good the same incase of recessed conduit as required
2.15 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit
breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing
and commissioning etc. as required.
Meter Room Modifications
Minor modification in existing meter panel/room for accommodating new connection.Drilling/cutting and
making good the same.Protection & Switching Supply and installation of 225 Amp MCCB Isolator of suitable
MR rating for the new connection. Interconnection with existing panel.but modification in busbar and Testing & Each 1 ₹50,000.00 50,000.00
Commissioning Insulation resistance testing, continuity checks, and load testing.Complete commissioning of
new connection.
Digitally signed by AMIT
Total of DB carried over to summary 61,500.00 151,417.00
Point wiring for light point /Fan/Exhaust Fan point/ call bell point using 2 runs of 1100 V grade 1.5 sqmm &
one run of 1.5 sq.mm FRLS insulated multistranded copper wires, in & including 25 mm dia , MS conduit
1 1.3 surface/ concealed in wall / ceiling conferming to IS 732 including all accessries such as junction boxes , conduit
bends, elbows and ceiling rose , and anodised GI switch box with modular switch ,modular plate and the box
covered with front plate
a 1.3.3 One light point controlled by one 6A switch Point 40.00 2,101.00 84,040.00
b 1.54.3 Secondary light point controlled by same switch Point 63.00 1,246.00 78,498.00
Wiring for light/ power plug with 2X4 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in
1.5 surface/ recessed steel conduit along with 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core Metre 288.00 480.00 138,240.00
cable for loop earthing as required.
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper
conductor, single core cable in surface/ recessed steel conduit as required.
a 1.7.1 2x1.5sqmm+1x1.5sqmm earth wire Point 230.00 370.00 85,100.00
c 1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Point 460.00 476.00 218,960.00
3 1.3.3 Exhaust fan point including of ceiling rose near fan. Point 2.00 2,101.00 4,202.00
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including
connections but excluding modular plate etc. as required.
c 1.24.4 3 pin 5/6 A socket outlet Each 23.00 136.00 3,128.00
d 1.24.5 6 pin 15/16 A socket outlet Each 35.00 219.00 7,665.00
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular
switches in recess etc. as required.
Supplying & fixing suitable size GI box with modular plate and cover in front on surface or in recess including
1.57 providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, Metre 288.00 807.00 232,416.00
painting etc. as required.
1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. Metre 288.00 112.00 32,256.00
6 1.28 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 0.00
SUBMAIN AND CONTROL WIRING 0.00 0.00
Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated
copper conductor, single core cable in surface/ recessed steel conduit as required.
1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 173.00 476.00 82,348.00
1.7.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 207.00 652.00 134,964.00
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with
7 1.19 fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as Meter 58.00 54.00 3,132.00
1.20 Supply and fixing of following sizes of MS conduit along with accessories in surface /recess including painting
8 in case of surface conduit,or cutting the wall and making good the same in case of recessed conduit as required 0.00
Digitally signed by AMIT
Total of Wiring carried over to summary 0.00 2,213,870.00
8 CABLE TRAY.& RACE WAY.
4.3 Supplying and installation following size of perforated painted with powder coating M.S. cable trays Tee with
perforation not more than 17.5%, joined with connectors, suspended from the ceiling with two
numbers MS/GI Suspenders i/c base of suitable size MS/GI angle, bolts & nuts, painting suspenders,
fastner etc as required.
8 GI Raceway & Junction boxes ( Raceway on floor shall be of aluminium only)
MR Providing and fixing 2 mm thick steel sheet factory fabricated post galvanized raceway with internal
partition/compartmentized of the following sizes including providing removable 3 mm thick GI cover, knock out
holes and fixing accessories earthing with 8 SWG copper earth wire complete as required including floor
supports, bends, access boxes, tap off boxes and cross over as per specification and site requirement.
(overhead / wall mounted recovery & function boxes shall be 1.6 mm thick)
c 150 mm wide x 38 mm deep raceway RM 12.00 1,988.00 23,856.00
d 100 mm wide x 38 mm deep raceway RM 46.00 1,524.00 70,104.00
Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables at the intersection
of raceways supplied completely with base and cover plates, height adjustable junction box 38- 90 mm
including all accessories ss plate of 2mm thick complete in all respect as per the directions of engineer in
Fabricating, supplying & installation on surface/ recess 2.0 mm thick factory fabricated GI Sheet raceways
height 50 mm and of totally enclosed with 2 mm thick covered. Two lengths of raceways and junction box shall
8 MR be joined together to make it dust proof. Chipping and removing screed to install the junction box in floor, 0.00
including removal and disposing of debris / fixing in ceiling along with suspender and accessories as per
instruction of Engineer in charge.
c 200 mm (wide) x 200 mm (length) X 50 mm (height) Nos. 7.00 1,580.05 11,060.38
Total of Raceway carried over to summary 190,570.38 108,745.00
1 26.2 Online UPS- Input supply: Three Phase, Output supply: Three Phase.
Supplying, installation, Testing & Commissioning of following capacity at full load (Unity Power Factor) at
operating temperature 0 to 40 0C, Relative humidity 0 to 95%, Online double conversion true sine wave
Uninterrupted hot swapable (allow for the replacement or addition of battery modules without shutting down
the entire system) modular Power Supply (UPS) system with N+1 modules (N denotes total number of modules
required for rated capacity). The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes
back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup time) on
full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch along with provision for manual
bypass, suitable isolation transformer for additional protection against neutral faults etc. UPS shall have inbuilt
phase sequence correction. The UPS systems offered are to be of the latest technology with Digital Control
Microprocessor based for
Digitally signed by AMIT
reliable operation using Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier & inverter (3 Level) with
PWM (Pulse Width Modulation). The quality of design, manufacturing and inspection process should confirm to
the relevant Inter-national standards such as IEC/EN/VDE. The operating efficiency of the UPS systems shall be
>96% while operating on battery mode and delivering quality power to the 100% non-linear loads. Current total
harmonic effect(ITHD) on the input grid shall be < 5% at 50 %load. (The required LC ( inductor (L) and a
capacitor (C)) filters shall be included in UPS cost), extreme power factor kit to be included to limit the input
power factor (PF) to 0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1
), however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be
suitable for incoming supply AC : 3Phase 400V +/-20%, 50 Hz +/-5 Hz, AC Output voltage: 3Phase 415 Volt, 50
Hz +/- 0.2Hz, Overload capacity of 120% for 10 mins, Sine wave output. Non condensing, noise level less than
60db at 1 meter distance, protections: Input Under voltage over voltage, abnormal out voltage, battery over
charging, output over current, short circuit protection, battery deep discharge protection, 10KV surge. UPS must
comply with low voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part
2, it shall be a Voltage and Frequency Independent (VFI)-type UPS. . Communication RS232/RS485/SNMP port
open protocol for BMS integration, all hardware & software for iOT Communication as per approved by
Engineering in charge. Required battery racks and interconnecting copper conductor cables of suitable size and
connectors and all required accessories are inclusive of the cost). This system must provide a means for logging
and alarming of all monitored points plus email notification. Forced air-cooling with integral inbuilt fans with
redundancy (if one fan fail UPS should be able to handle at least 80% of the load, Noise Level 65 DB at 1 meter
distance. The system shall be in compliance IEC 62040- 1,2 & 3, IS: 16242 and CPWD Specification. Display Panel
(minimum) (In-build 5 inch or more LC Display / LED) to display : a) Input: Voltage, current, Frequency. b)
Bypass: Voltage, Frequency. c) Output: Voltage, frequency, Current. d) Battery:
Voltage, Capacity. e) Load: KVA, KW, Percentage. f) Temperature: STS, Inverter, PFC. g) Event Logging &
Statistical Data (On LCD/LED): UPS should capture and display up to 3000 events like: Over temperature / DC
Bus Fail / Fan Fail / Fuse Fail / Overload / Short-circuit / Device Fail / Inverter Fail / Rectifier Fail / Bypass Fail,
etc. h) Statistical Data: No. of power failures / Transfers to Bypass / Total Running time, etc. i) Mains Mode of
Operation /Battery Mode of Operation / Bypass feeding the load / UPS Fault /Battery charging and discharging,
overload, battery voltage and battery capacity. j) Audible Alarms : Mains Failure, Battery Low Alarm, UPS
Overload, Fault, Shutdown, Input Over, Under Voltage, Output Over, Under Voltage, Battery Over, Under
Voltage, Over Load and short circuit, Over Temperature. The UPS should have QR code which should contain
drawing, test report OEM manual, Geo- Tag of manufacturing location etc
26.2.2 20KVA (Each Power module shall be < 10 KVA) EACH 1.00 341,772.00 341,772.00
5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. MTR 440 84.00 36,960.00
STATIC SWITCH MODULE FOR FLOOR DB
SITC of static switch module with microprocessor based control and suitable for liner and non linear load at
particulars distribution board of critical load in event of short circuit overload or any other fatal condition with
built-in Technical Protections like short circuit, Overload, High/Low Voltage cutoff protection of load from source
inclusive of Bypass facility Static Bypass Module is activated during malfunctioning conditions of load like :-
• Short Circuit
• Bypassing of particular load if required
• Resulting in non tripping of main UPS unit
• Input Voltage (320-460VAC) 3 phase
• Input frequency 50Hz
Digitally signed by AMIT
Indication & Monitoring
• UPS Supply on/source I
• Load on UPS supply/source I
• Main supply on/source II
• Load on mains supply/Bypass
• Bypass Switch on
• Bypass Switch off
Providing, Supplying, Installing, Testing and Commissioning (SITC) of Electric modular wiring accessories comprising
switches, sockets, data and communication outlets complete with modular cover plates, mounting frames and GI flush
boxes as required for office workspace areas.
The work shall include Schneider Electric AvatarOn / Livia / Zencelo Series or approved equivalent modular accessories
conforming to relevant IS/IEC standards. All switches and sockets shall be manufactured from high-impact, self-
extinguishing, flame-retardant polycarbonate material with silver alloy contacts, suitable for operation at 240V AC, 50Hz
The scope shall include:
6A, 1-way modular switches.
6A, 2-way modular switches.
16A modular switches. EACH
Bell push switches.
6A/16A modular socket outlets.
16A power socket outlets.
Electronic fan regulators.
RJ45 CAT-6 data outlets.
Telephone outlets.
USB charging outlets.
DP switches with LED indicators.
Blank modules as required.
Modular front cover plates.
Modular mounting grids/support frames.
Powder-coated GI flush boxes of required size.
Interconnections, ferrules, sleeves, screws, fixing accessories and all mounting hardware.
Digitally signed by AMIT
Summary of Lighting Works
Sl no Item description Image UOM Qty Unit Price Amount
Supply of DALI dimmable 10W, suspended by 1.5m suspension wire, 2 feet linear, IP40 from front, SMD LED luminaire with
system efficacy of 120 lumen/watt and system lumen output of 1200 lumen, operating in an ambient temperature of 0⁰C to
45⁰C. Operating at 50Hz frequency, luminaire shall have extruded aluminium housing in white with high efficiency prismatic
diffuser for UGR<19 and must have provision for end to end seamless connectivity. EMC package of wattage of 0.2-0.5 W
LEDs used in the product shall comply with IEC 62471 for Photo-biological safety. LM 80-08 compliant LEDs from reputed
makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. The LED shall comply with L70 life of
50000 burning hours tested at maximum current. The LEDs used should be with CCT of 4000 K and CRI of Minimum 80, with
MacAdam CCT binning ≤3 mounted on 1.6mm FR4 / MCPCB with 35 micron cu layer. LED Driver shall be Isolated type,
Constant Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of 198V
to 264V (nominal rated voltage – 240V) with 2KV internal surge protection, Power factor of minimum 0.95, driver efficacy of
minimum 85% and total harmonic distortion (THD) of less than or equal to 10% should be integral to the luminaire. LED
driver should be DALI2.0 compatible . Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt
of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters.
Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) :
2012; IS 16108 : 2012. Dimension: 604X50X75mm, weight: 0.8Kg
Supply of DALI dimmable 25W, suspended by 1.5m suspension wire, 5 feet linear, IP40 from front, SMD LED luminaire with
system efficacy of 120 lumen/watt and system lumen output of 3000 lumen, operating in an ambient temperature of 0⁰C to
45⁰C. Operating at 50Hz frequency, luminaire shall have extruded aluminium housing in white with high efficiency prismatic
diffuser for UGR<19 and must have provision for end to end seamless connectivity. EMC package of wattage of 0.2-0.5 W
LEDs used in the product shall comply with IEC 62471 for Photo-biological safety. LM 80-08 compliant LEDs from reputed
makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. The LED shall comply with L70 life of
50000 burning hours tested at maximum current. The LEDs used should be with CCT of 4000 K and CRI of Minimum 80, with
MacAdam CCT binning ≤3 mounted on 1.6mm FR4 / MCPCB with 35 micron cu layer. LED Driver shall be Isolated type,
Constant Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of 198V
to 264V (nominal rated voltage – 240V) with 2KV internal surge protection, Power factor of minimum 0.95, driver efficacy of
minimum 85% and total harmonic distortion (THD) of less than or equal to 10% should be integral to the luminaire. LED
driver should be DALI2.0 compatible. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of
India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Compliance
to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 :
2012. Dimension: 1504X50X75mm, weight: 1.2Kg
Digitally signed by AMIT
Supply of DALI dimmable 30W, suspended by 1.5m suspension wire, 6 feet linear, IP40 from front, SMD LED luminaire with
system efficacy of 120 lumen/watt and system lumen output of 3600 lumen, operating in an ambient temperature of 0⁰C to
45⁰C. Operating at 50Hz frequency, luminaire shall have extruded aluminium housing in white with high efficiency prismatic
diffuser for UGR<19 and must have provision for end to end seamless connectivity. EMC package of wattage of 0.2-0.5 W
LEDs used in the product shall comply with IEC 62471 for Photo-biological safety. LM 80-08 compliant LEDs from reputed
makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. The LED shall comply with L70 life of
50000 burning hours tested at maximum current. The LEDs used should be with CCT of 4000 K and CRI of Minimum 80, with
MacAdam CCT binning ≤3 mounted on 1.6mm FR4 / MCPCB with 35 micron cu layer. LED Driver shall be Isolated type,
Constant Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of 198V
to 264V (nominal rated voltage – 240V) with 2KV internal surge protection, Power factor of minimum 0.95, driver efficacy of
minimum 85% and total harmonic distortion (THD) of less than or equal to 10% should be integral to the luminaire. LED
driver should be DALI2.0 compatible . Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt
of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters.
Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) :
2012; IS 16108 : 2012. Dimension: 1804X50X75mm, weight: 2.4Kg
Supply of Y-shaped DALI dimmable 15W, suspended by 1.5m suspension wire, 300mm each arm, IP40 from front, SMD LED
luminaire with system efficacy of 120 lumen/watt and system lumen output of 1800 lumen, operating in an ambient
temperature of 0⁰C to 45⁰C. Operating at 50Hz frequency, luminaire shall have extruded aluminium housing in white with
high efficiency prismatic diffuser for UGR<19 and must have provision for end to end seamless connectivity. EMC package of
wattage of 0.2-0.5 W LEDs used in the product shall comply with IEC 62471 for Photo-biological safety. LM 80-08 compliant
LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. The LED shall comply
with L70 life of 50000 burning hours tested at maximum current. The LEDs used should be with CCT of 4000 K and CRI of
Minimum 80, with MacAdam CCT binning ≤3 mounted on 1.6mm FR4 / MCPCB with 35 micron cu layer. LED Driver shall be
Isolated type, Constant Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage
range of 198V to 264V (nominal rated voltage – 240V) with 2KV internal surge protection, Power factor of minimum 0.95,
driver efficacy of minimum 85% and total harmonic distortion (THD) of less than or equal to 10% should be integral to the
luminaire. LED driver should be DALI2.0 compatible. Manufacturer shall have inhouse lab approved by NABL or ministry of
science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above
parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885
Digitally signed by AMIT
Supply of V-shaped DALI dimmable 10W, suspended by 1.5m suspension wire, 300mm each arm 60deg apart, IP40 from
front, SMD LED luminaire with system efficacy of 120 lumen/watt and system lumen output of 1200 lumen, operating in an
ambient temperature of 0⁰C to 45⁰C. Operating at 50Hz frequency, luminaire shall have extruded aluminium housing in
white with high efficiency prismatic diffuser for UGR<19 and must have provision for end to end seamless connectivity. EMC
package of wattage of 0.2-0.5 W LEDs used in the product shall comply with IEC 62471 for Photo-biological safety. LM 80-08
compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. The LED
shall comply with L70 life of 50000 burning hours tested at maximum current. The LEDs used should be with CCT of 4000 K
and CRI of Minimum 80, with MacAdam CCT binning ≤3 mounted on 1.6mm FR4 / MCPCB with 35 micron cu layer. LED
Driver shall be Isolated type, Constant Current topology driver with proper heat sink for heat dissipation suitable to operate
in input voltage range of 198V to 264V (nominal rated voltage – 240V) with 2KV internal surge protection, Power factor of
minimum 0.95, driver efficacy of minimum 85% and total harmonic distortion (THD) of less than or equal to 10% should be
integral to the luminaire. LED driver should be DALI2.0 compatible. Manufacturer shall have inhouse lab approved by NABL
or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify
above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885
Supply ofDALI dimmable 20W Suspended Acoustic Mute light fixture of 1200mm length linear profile. The light fixture
should be impeccably integrated with Acoustic material which enhances the product Aesthetic looks. The Acoustic PET board
material should be made of High quality Acoustic polyester fibre with Hybrid technology. The Hybrid technology utilizes
deep airspaces and multiple layers construction which in combinations of Acoustic material+Soft polyester+PET Board which
insures Higher NRC Value of 0.85-0.9 and greater SAC Sound absorption coefficient. Hybrid deep airspaces technology
insures the up to 40-50% Average decrement in reverberation time (RT60). All the acoustic materials must be tested in third
Party Acoustic Labs preferably in ARAI to insure the quality of product. The PET board should be made of 100%
recyclable/sustainable material. Acoustic body should be light weight for easy and effective installation and should be having
fire Retardant property & should comply to Fire Classification: B s1, d0 as per EN 13501. The Acoustic materials should be
high resistance to humidity and moisture. The product should be Non VOC compliant and should be having Anti-fungal
properties. The Acoustic material should be also available for customization as per customer demand in Different
customization options in shape, size, formation and RAL shades. The luminaire integrated with the acoustic material should
be having system output ranges from ≥2000 lm with collimeter lens having UGR<16. Luminaire shall have Optical Grade High
6 Efficiency Translucent PC diffuser. The LED used inside the light fixture should be LM 80-08 compliant, ANSI rated LEDs from nos 5.00 27,500.00 137,500.00
reputed makes such as Nichia, Japan / Cree, USA / Bridgelux, USA / Lumiled USA / Citizen Japan should be provided.
Luminaire shall use multiple LEDs of less than 0.5W Class for better diffusion and heat management. The LEDs shall be driven
on optimal point for higher reliability & performance. The LED shall be compliant with LM80-08 standard with Useful L70 life
of 50000 Hrs (Complete LM 80 test report for LED should be submitted). The LEDs used in luminaire should be ANSI standard
Rated LED with CCT of 4000K and CRI of Minimum 80. LEDs used must be tested as per EN62471 for Photobiological Safety
of humans. The Driver should be Isolated type, multistage Constant Current Constant Voltage topology driver suitable to
operate in input voltage range of 150V to 270V ( nominal rated voltage – 240V) with minimum 2KV surge protection, driver
efficiency is ≥85% along with Power factor≥0.95 and total harmonic distortion iTHD≤10% should be non-integral to the
luminaire. Driver shall be made in India for better service and availability. Driver output voltage shall be less than SELV limits
for safe DC operation and maintenance. The light fixture should BIS approved/certified. Also the light fixture should be
having LM79 Test Report from Third Party NABL Lab with IES Files. Compliance to Indian Standards of IS10322 Part 5 / Sect
Digitally signed by AMIT
Supply of DALI dimmable 20W COB LED Downlight luminaire having 1600 lumens, with cut-out (Φ) dia of 74mm and height
of 175mm, suitable for pendant mounting. Luminaire shall be made up of white powder coated extruded Aluminium housing
with inbuilt heat sink to provide better thermal management to enhance LED life. Suspension wire of 1.5m should be
supplied with the luminaire. The luminaire should be equiped with the secondary optics of high efficiency reflector with clear
glass to have precise light beam to cut down glare to UGR <19. LM 80-08 compliant LEDs from reputed makes such as
Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. LEDs used in the product shall comply with EN 62471 for
Photo-biological safety and certificate for the same from manufacturer shall be provided. The luminaire should be IP20
rated. The LED shall be compliant with LM80-08 standard with L70 life of 50000 Hrs tested at maximum current (Complete
LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs used should be with CCT of 4000 K and CRI
of Minimum 80. LED Driver shall be Integrated type, Isolated, Constant Current operated driver with range 140-280V AC.
Driver Efficiency > 83% & 2 KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD)
of less than 15% should be integral to the luminaire. Manufacturer shall have inhouse lab approved by NABL or ministry of
science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above
parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885
Supply of DALI dimmable 1200mm dia Pendent Mounted Ring LED. Fixture to be made of extrusion Aluminum housing in
white/black finish with HET plastic diffuser. LED Used shall be SMD type with Minimum system Lumens 5100 @60W &
efficacy 85lm/W,Life of fixture : 50000 burning Hrs. @ L70 Lumen maintenance, CCT of 4000/5700K (SDCM<=3), CRI Ra
8 >=80, PF >0.95, THD<10%, operating Voltage Range of 198-264 V AC. Minimum Internal Surge Protection 2.0KV. nos 9.00 41,250.00 371,250.00
Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need
to be submitted from a NABL/UL accredited lab to verify above parameters. Both the fixture and Driver should have separate
BIS approval. Luminaire should have RoHS, EMI EMC as per IEC 61547, CISPR 15.
Supply of DALI dimmable and tunnable Suspened LED stretch fabric Luminaire, with extruded aluminum housing delivering
upto 3890lumen/sq m and it draws 55W/sq m maximum from standard 220-240V AC supply . Fixture offers excellent light
output, long source life, high CRI, and energy efficiency, in a beautiful, clean plane of light. Industry-best quality of 80+ CRI
and color consistency within a 3-step MacAdam ellipse provides a glare-free direct view luminaire, and abundant, uniform
daylight illumination evenly lit across the entire task surface.The diffuser shall be Special translucent stretch fabric having
9 good resistance properties -Flame retardant, Anti-bacterial, Anti-Fungal and Anti-Static, Impermeable to Water and steam sqm 4.19 55,752.00 233,840.06
for uniform and optimum light distribution. Fixture should have IP20, PF ≥ 0.95, THD<=10%, CRI 80 and drive should have
Surge Protection upto 2KV and must be compatible with DALI 2.0 for both tunning and dimmable option. The LED Driver
shall be easily available in India for repair and service. DALI 2 Driver must be with Part 251, 252 and 253 for energy
mesaurement data. The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with
Photo Biological Safety Standard. Luminaire should have RoHS, EMI EMC as per IEC 61547, CISPR 15.
Digitally signed by AMIT
Supply of DALI dimmable IP20 curvilinear suspended luminaire made of extruded aluminium housing and is should have high
transmissive diffuser. Housing color(RAL code) to be approved by specifier. Fixture should have minimum efficacy at System
level (Not Chip Level) >85lumens/watt(SDCM<3) and a minimum system lumen output of 1700lumens/m (±10%) and
maximum system wattage of 20W/m.Luminaire should have Life of 50,000hrs@L70 Lumen maintenance at 45deg C ambient
temperature, CCT up to 4000K, IP20, IK02, CRI >80, PF >0.95, THD<10% at full load and an operating Voltage Range of( 180 -
264)V AC, Internal Surge Protection 2KV & driver efficacy >85%. The fixture should comply with the parameters as per
IS10322. Fixture should have class I insulation. LED driver should be DALI2.0 compatible. Manufacturer shall have inhouse lab
approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL
accredited lab to verify above parameters.
Supply of DALI dimmable Magnetic cylindrical track Light with collimeter lens of System Wattage 12W in Black Color Housing.
The lights can be easily attach of de-attach from the track channel. The magnetic lamp inside with dimmable driver, match
with transformer dimming. CT-3000/4000K,
CRI-80 Watt- 12W Beam Angle 24°, Dia Ø45, length: 100mm, Tolerence of ± 5mm.
Supply of DALI dimmable Magnetic fixed head LED Light with collimeter of System Wattage 12W in Black Color Housing. The
lights can be easily attach of de-attach from the track channel. The magnetic lamp inside with dimmable driver, match with
transformer dimming. CT-3000/4000K,
CRI-80 Watt- 12W Beam Angle 36° width - 22mm Length -220mm height -45mm Tolerence of ± 5mm.
Supply of Recess Mounted Magnetic Track with Cut-out of 27mm -30mm. The dimensions are as follows: Dimensions (mm):
13 25 (W) x 56 (H) x (L) Available -1000mm. All dimensions are in tolerance of ± 5mm & Lifetime: 50,000hrs Mounting Type: Mtr 5.00 2,560.00 12,800.00
Recessed Type ,designed for Indoor Application with Ingress Protection of IP20.
14 Supply of Magnetic track fixed jointer for seamless continuous installation. nos 3.00 800.00 2,400.00
Supply of Magnetic Track Driver Available in 100W Surge Protection 3KVA ,48V Split Transformer (external power supply) to
be rquired to install as per the site requirement.
16 Supply of Magneto Track connector -INPUTLINE (For DALI of external driver only). nos 4.00 800.00 3,200.00
Digitally signed by AMIT
Supply of DALI dimmable 9W recessed, deep inset COB LED Downlight luminaire having 810 lumens with dimensions of
62mm dia and height of 74mm. The cut out dia (Φ) should not be more than 57mm. Luminaire shall be made up of pure
polyster powder coated pressure die cast Aluminium housing with inbuilt heat sink to provide better thermal management
to enhance LED life. The luminaire should be equiped with the secondary optics of high efficiency white coloured reflector.
The luminaire should be available with multiple beam angle options of 40° and 60°.LM 80-08 compliant ceramic / aluminium
base LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Citizen should be provided. LEDs used in the
product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be
provided. The luminaire should be IP20 rated. The LED shall be compliant with LM80-08 standard with L70 life of 50000 Hrs
17 tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs nos 10.00 5,500.00 55,000.00
used should be with CCT of 4000 K and CRI of Minimum 80. LED Driver shall be non-integrated type, Isolated, Constant
Current operated driver with range 198-264V AC. Driver Efficiency > 70% & 2.0 KV internal surge protection, Power factor
greater than 0.90 and total harmonic distortion (THD) of less than 15% should be integral to the luminaire. DALI 2 Driver
must be with Part 251, 252 and 253 for energy mesaurement data. Manufacturer shall have inhouse lab approved by NABL
or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify
above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885
Supply of DALI dimmable 15W recessed, deep inset COB LED Downlight luminaire having 1350 lumens with dimensions of
83mm dia and height of 91mm. The cut out dia (Φ) should not be more than 78mm. Luminaire shall be made up of pure
polyster powder coated pressure die cast Aluminium housing with inbuilt heat sink to provide better thermal management
to enhance LED life. The luminaire should be equiped with the secondary optics of high efficiency white coloured reflector.
The luminaire should be available with multiple beam angle options of 40° and 60°.LM 80-08 compliant ceramic / aluminium
base LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Citizen should be provided. LEDs used in the
product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be
provided. The luminaire should be IP20 rated. The LED shall be compliant with LM80-08 standard with L70 life of 50000 Hrs
18 tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs nos 50.00 5,455.00 272,750.00
used should be with CCT of 4000 K and CRI of Minimum 80. LED Driver shall be non-integrated type, Isolated, Constant
Current operated driver with range 150-270V AC. Driver Efficiency > 75% & 2.0 KV internal surge protection, Power factor
greater than 0.90 and total harmonic distortion (THD) of less than 15% should be integral to the luminaire. DALI 2 Driver
must be with Part 251, 252 and 253 for energy mesaurement data. Manufacturer shall have inhouse lab approved by NABL
or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify
above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885
Supply of Flexi Strip 5W/M Flexible LED Strip with high performance LEDs, suitable for mounting in cove for indirect lighting
with non- integral electronic LED driver. High efficiency long life LED package in integral module with lumen efficacy of >75
lm/W. Lumen Output of 375lumens/mtr. CRI >80, Color temperature 4000K, IP20. Life class of 50,000 hrs @ L70B0,
Operating Temperature:0 TO +45 DEG.C; Input Supply Voltage Range: 100-300 V, Frequency: 50-60 HZ; 5m Roll.
Digitally signed by AMIT
Supply of 8ft 60W 70% DOWN/ 30% UP LED linear pendant mounted DALI Dimmable Luminaire suitable for suspended
insatllation in offices, studio and similiar interiors. The luminaire having 7200lm (±10%) and system efficacy 120lm/W shall
have a slim extruded aluminium body with die cast endcaps and use high efficeincy LEDs with a polycarbonate optics,
providing symmetric 60 degree optics. Housing color(RAL code) to be approved by specifier. Luminaire shall have technology
edge with high efficacy LEDs .It sall have low glare with <16 (Up/Down), CCT of 4000k, CRI 80 and a rated LED life span of
50,000 hrs at L70. The fixture shall operate at 240V AC, with a voltage range of 180-264 (normal driver), support loop-in loop-
out wiring. IP 20 rated, it shall operate between 0-45 deg C and include surge protection of 2kV. The luminaire must comply
20 ANSI bin C78.377A for CCT Binning. Driver Efficiency > 85% Power factor greater than 0.95 and total harmonic distortion nos 2.00 27,500.00 55,000.00
(THD) of less than 10%. Luminaire shall have non-integrated driver and comply LG6 Guidelines. DALI 2 Driver must be with
Part 251, 252 and 253 for energy mesaurement data. Manufacturer shall have inhouse lab approved by NABL or ministry of
science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above
parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885
(Part2/Sec13) : 2012; IS 16108 : 2012. Luminaire should have RoHS, EMI EMC as per IEC 61547. Light should be integrated
with LMS of same make for better compatibility.
Supply of linear IP20 Pendent of length 1220mm Mounted LED fixture made of Aluminium powder coated inner surface with
swiveling light module. Fixture should have canopy of triangular cross-section integrated with suspension wire 1.5mtr. LED
Used shall be SMD type with Minimum system Lumens 2400 @30W & efficacy 80lm/W,Life of fixture : 50000 burning Hrs. @
L70 Lumen maintenance, CCT of 4000K (SDCM<=3), CRI Ra >=80, PF >0.95, THD<10% at full load, operating Voltage Range of
21 198-264 V AC. Minimum Internal Surge Protection 2.5KV. Manufacturer shall have inhouse lab approved by NABL or ministry nos 1.00 28,500.00 28,500.00
of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above
parameters. Both the fixture and Driver should have separate BIS approval. Dimension: 1220X156X121mm, Weight: 6.2Kg.
Housing color: Black/Orange/Yellow to be confirmed by EIC
Supply of wireless IoT System having BLE 5.2 AES 128 Bit encyption based 32 child DALI controller and analog 2 channel (0-
10V) output, operates on 100-277 VAC, 10-30mA, 50Hz, DALI 2.0 protocol. Sensor input of 0-3V DC & 1mA. For analog
dimming, It provides output voltage of 0-10V DC +/- 0.2V and 15mA per channel. For DALI output, it provides 12-20V DC and
160mA max for 32 DALI devices. An auxillary power output of 3.3VDC and 30mA. 0 - 100% dimming, device to device range
30m. Controller must control individually control standard DALI or Tunable DALI Drivers independantly or combination of
both. Operating temperature -20 to 50 deg celsius, surge protection 3kV. System shall support easy commissioning and
configuration via Mobile Application along with user and site management features. Luminaire and IOT system should be of
same make. Optional Cloud Application must be available for control and monitoring of the devices along with analytics
reports. Mobile Application shall have features of individual & group control for On/off/dimming/ colour tuneing / Scene
Control / Animation etc. Device must have security key for commissioning and replacement for future. Dimension: 70.9 X
Digitally signed by AMIT
Supply of wireless IoT System having BLE 5.2 AES 128 Bit encyption based 4 child DALI controller, operates on 90-277 VAC,
65mA, 50Hz, following DALI 2.0 protocol. It must have auxillary power output of 12V DC & 100mA to power sensor devices
& 8mA current connected to 4 DALI drivers, 0 - 100% dimming, device to device range 30m. Controller must individually
control standard DALI or Tunable DALI Drivers independantly or combination of both. Operating temperature -20 to 50 deg
celsius, surge protection 4kV. System shall support easy commissioning and configuration via Mobile Application along with
user and site management features. Optional Cloud Application must be available for control and monitoring of the devices
along with analytics reports. Mobile Application shall have features of individual & group control for On/off/dimming/ colour
tuneing / Scene Control / Animation etc. Device must have security key for commissioning and replacement for future.
Dimension: 45.1 x 35.1 x 20.2mm(+/-2)
Supply of BLE 5.2 AES 128 Bit encyption based multi sensing device with low bay PIR and ambient light (0-2000 lux) sensing,
with two 0-10V DC channels to control CCT and intensity. Operates on input voltage of 12-20 V DC with input current of
30mA at 12VDC and 25mA at 24VDC, 50Hz. Output is a 2 channel, 0-10V DC with 15mA current. Ceiling mounting height is
2.4m - 4m and maximum detection range is 14m dia at 4m mounting height. Device to device range 30m, operating
temperature 0 to 50 deg celsius. Luminaire and sensor system should be of same make.System shall support easy
24 commissioning and configuration via Mobile Application along with user and site management features. Optional Cloud nos 5.00 14,500.00 72,500.00
Application must be available for control and monitoring of the devices along with analytics reports. Mobile Application shall
have features of commissioning of the sensors along with setting step dim function, sensitivity levels and time day options.
Device must have security key for commissioning and replacement for future. Device must have security key for
commissioning and replacement for future. Dimension: 89.8 x 107.7mm(+/-2)
Supply of BLE 5.2 AES 128 Bit encyption based, AC Powered Wireless PIR Motion & Light Sensor (0-2000 lux). Operates on
input voltage of 90-277 V AC with input current of 9mA at 230VAC and 15mA at 90VAC, 50Hz. Ceiling mounted with
maximum height of 4m and maximum detection range of 14m dia at 4m mounting height. Device to device range 30m,
operating temperature 0 to 80 deg celsius, surge rating 4kV. System shall support easy commissioning and configuration via
Mobile Application along with user and site management features. Luminaire and sensor system should be of same
make.Optional Cloud Application must be available for control and monitoring of the devices along with analytics reports.
Mobile Application shall have features of commissioning of the sensors along with setting step dim function, sensitivity levels
and time day options. Device must have security key for commissioning and replacement for future. Device must have
security key for commissioning and replacement for future. Diemnsion: 89.8 x 107.7mm(+/-2)
Supply of WiFi and BLE 5.2 AES 128 Bit encyption Gateway with Ethernet and built-in Real Time Clock for cloud connectivity
and scheduling.It is powered by 5V, 2A Mini USB / DC Adaptor and has 1 ethernet port with 10/100 Mbps data transmission
rate. RTC is battery powered with 3V DC. Device to device range 30m X 30m, operating ambient temperature of -20 to 55
deg celsius. System shall support easy commissioning and configuration via Mobile Application along with user and site
management features. Luminaire and gateway system should be of same make. Optional Cloud Application must be
available for control and monitoring of the devices along with analytics reports. Device must have security key for
commissioning and replacement for future. Diemsnion: 120 x 120 x 29.5mm(+/-2)
Digitally signed by AMIT
Supply of iSense Air Quality Sensor with capability to monitor AQI, temperature, humidity, CO₂, PM1.0, PM2.5, PM10, and
TVOC. The sensor operates on 5VDC Mini B-USB with 0.5W power consumption, using Bluetooth communication
(2402–2480MHz frequency and 30m range) and internal wire antenna. It connects with the Wipro iSense IoL app and Enor E
gateway for real-time remote monitoring and data upload. Luminaire and air quakity sensor system should be of same
27 make. Measuring ranges: Temperature 0–50°C, RH 0–100%, CO₂ 400–65,000 ppm, PM 0–500 µg/m³, TVOC 0–65,000 ppb, nos 2.00 44,500.00 89,000.00
and AQI 1–5. Enclosure made of durable polycarbonate ABS , suitable for surface mounting with screw/hook options.
Ensures reliable, encrypted communication with AES 128-bit.
Dimension (L x W x H):124.2 x 66 x 36mm (±2mm)
Supply of BLE 5.2 AES 128 Bit encyption based wireless battery powered 5-button wall switch that controls ON/OFF, intensity
and CCT of an individual or group of luminaires.Operates on 3V DC input voltage in an ambient temperature of 0 to 50 deg
celsius and device to device range 30m. System shall support easy commissioning and configuration via Mobile Application
along with user and site management features. Optional Cloud Application must be available for control and monitoring of
the devices along with analytics reports. Dimensions: 105 X 40 X 12mm(+/-2)
Supply of BLE 5.2 AES 128 Bit encyption based wireless battery powered 8-button wall switch that controls ON/OFF, intensity
and CCT of an individual or group of luminaires and scene setting. Operates on 220-240V AC input voltage in an ambient
temperature of 0 to 50 deg celsius and device to device range 30m. System shall support easy commissioning and
configuration via Mobile Application along with user and site management features. Optional Cloud Application must be
available for control and monitoring of the devices along with analytics reports. Dimensio: 44.4 x 33.2 x 105mm(+/-2)
Provides all features of commissioning, configuration, control and automation as in mobile app along with license.
Additionally, measures, tracks and reports real time energy usage for every floor, zone, group and device; gives data on
occupancy patterns by heat maps; emergency monitoring, space and energy management, asset tracking, multi-tier data
security, data encryption, authenticated user access, on premise and remote access with BMS point integration
Grand Total for Lighting Works 3,183,943.06
Grand Total for Lighting Works 3,183,943.06
Digitally signed by AMIT
ESTIMATED COST FOR FA & PA SYSTEM
A. SITC OF FIRE ALARM SYSTEM & ACCESSORIES : MR. DSR.
Sr. No DSR 2025. No. Description Unit Qty Unit Rate Total amount Total amount
Sr. No DSR 2025. No. Description Unit Qty Unit Rate Total amount Total amount
Supplying, installation, testing and commissioning of micro processor based
intelligent addressable main fire alarm panel, central processing unit with
the following loop modules and capable of supporting not less than 240
devices (including detectors) and minimum 120 detectors per loop and
loop length up to 2 km, network communication card, minimum 320
character graphics/ LCD display with touch screen or other keypad and
minimum 4000 events history log in the non volatile memory (EPROM), power
supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed
maintenance free batteries with automatic charger. The panel shall have
facility to connect printer to printout log and facility to have seamless
integration with analog/digital voice evacuation system (which is part of the
schedule of work under SH: PA System) and shall be complete with all
accessories . The panel shall be compatible for IBMS system with open
protocol BACnet/ Modbus over IP complete as per specifications.
Supplying, installation, testing & commissioning of intelligent analog
2 28.2.4 addressable photothermal detector complete with mounting base Pcs 23.00 3,004.00 69,092.00
complete as required.
Supplying, installation, testing & commissioning of intelligent addressable
3 28.2.9 thermal detector with rate of rise cum fixed tempreature thermistor Pcs 2.00 2,866.00 5,732.00
complete with base as required.
Supplying, installation, testing & commissioning of addressable manual call
point complete as required.
Supplying, installation, testing & commissioning of addressable strobe
complete as required.
Supplying, installation, testing & commissioning of fault isolator complete
with base as required.
Supplying, installation, testing & commissioning of response indicator on
7 28.2.5 surface/recessed MS Box having two LED, metallic cover complete with all Pcs 3.00 306.00 918.00
connections etc as required.
B CABLES & ACCESSORIES FOR FAS : 0.00
Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V
1 28.5.2 rated with annealed copper conductor having XLPE insulation, steel wire RM 225.00 192.00 43,200.00
armouring & FRLS outer sheath complete as required.
C SITC OF PUBLIC ADDRESSABLE SYSTEM & ACCESSORIES : 0.00
Supplying, installation, testing & commissioning of 6 zone, voice alarm
controller with USB, MP3 player (including 6 zone button paging station) with
seamless integration facility with main fire alarm panel for voice evacuation
complete as required.
Supplying, installation, testing & commissioning of digital audio amplifier 50
Watt, 25V rms operating at 240 volt AC supply complete as required.
Digitally signed by AMIT
Supplying, installation, testing & commissioning of ceiling/wall mounted loud
speaker, 3/1.5 Watt in ABS enclosure complete as required.
D CABLE & ACCESSORIES FOR PA SYSTEM 0.00
Supplying and drawing of cable Fire Retardant PVC insulated copper
conductor cable in the existing surface / recessed steel conduit of following
pairs, cores and size including connections and interconnections etc. as
28.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm RM 180.00 61.00 10,980.00
Supply and fixing of following sizes of MS conduit along with accessories in
2 1.20 surface /recess including painting in case of surface conduit,or cutting the 0.00
wall and making good the same in case of recessed conduit as required
Digitally signed by AMIT
Interior/Fitout works of Office Space of ICMR at PLate A (Rear Side), Office Block -3, Ground Floor, East Kidwai Nagar, New
BOQ FOR PLUMBING & FIRE FIGHTING
SECTION DESCRIPTION DSR (AMOUNT) NDSR (AMOUNT)
A SANITARY FIXTURES & FITTINGS 7,865.50 26,796.00
B WATER SUPPLY 56,036.55 0.00
C SPRINKLER PIPING & ACCESSORIES 426,972.00 56,195.00
Correction Factor on A, B and C by 0.973 62,176.69
Total Cost ( Carried Forward) in Rs. 489,148.69 82,991.00
Digitally signed by AMIT
Interior/Fitout works of Office Space of ICMR at PLate A (Rear Side), Office Block -3, Ground Floor, East Kidwai Nagar, New Delhi
BOQ FOR PLUMBING & FIRE FIGHTING
SUB HEAD A: SANITARY FIXTURES & FITTINGS
SL. NO. DSR 2023 DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)
Providing & fixing PVC waste pipe for sink including PVC
waste fitting Complete. Flexible Pipe
Providing & fixing Horizontal liquid soap dispenser with
2 MR stainless steel lid and brackets fixed to wooden cleats with Each 1 3,715.00 3,715.00
C.P. brass screws.
Providing & fixing, testing and commissioning of storage
type electric water heater with automatic thermostatic
control electric element, pressure release valve, brackets
fixed to expansion fasteners with M.S. nuts and bolts all
complete including cutting and making good the walls
wherever required.
15 litres capacity (Horizontal /Vertical type1.5 kw electrical
Providing & fixing PTMT towel ring trapezoidal shape 215
mm long 200 mm wide with minimum distance of 37 mm
4 17.72 from wall face with concealed fittings arrangement of Each 1 231.95 231.95
approved quality and colour weighing not less than 88 gms
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen
sink as per IS:13983 with C.I. brackets and stainless steel
plug 40 mm, including painting of fittings and brackets,
cutting and making good the walls wherever required :
17.10.1 Kitchen sink with drain board
Supply, installation, testing and commissioning of 15mm
C.P. brass single hole sink mixer complete.
Digitally signed by AMIT
Detail of Sanitary fixture are for the information of the
Contractor,however model/makes of all sanitary fixtures
shall be selected by Architect/Interior designer/Project
manager and the same shall be binding for execution.
ii. No additional fixing cost shall be paid for change in type of sanitary fixtures.
iii. Contractor to receive all the above mentioned items & store at place as directed at site.
TOTAL CARRIED OVER TO SUMMARY 7,865.50 26,796.00
Digitally signed by AMIT
SUB HEAD B: WATER SUPPLY
SL. DSR DSR Rate NS Rate
DESCRIPTION OF ITEMS UNIT Qty DSR Amount (Rs) Amount
Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes
having thermal stability for hot & cold water supply including all
(CPVC) plain & brass threaded fittings including fixing the pipe
with clamps at 1.00 m spacing. This including jointing of pipes &
fittings with one step CPVC solvent cement and testing of joints
complete as per direction of engineer in charge. .
Internal Work - Exposed on Wall
18.7.5 40 mm nominal outer dia pipes. Metre 10.00 702.95 7,029.50
18.7.6 50 mm nominal outer dia pipes. Metre 20.00 934.15 18,683.00
Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes
having thermal stability for hot & cold water supply including all
CPVC plain & brass threaded fittings i/c fixing the pipe with
clamps at 1.00 m spacing. This including jointing of pipes &
fittings with one step CPVC solvent cement and the cost of
cutting chases and making good the the same including
testing of joints complete as per direction of engineer in
Concealed work oncluding cutting chases and making good
18.8.2 20 mm nominal outer dia pipes. Metre 10.00 537.60 5,376.00
18.8.3 25 mm nominal dia Pipes Metre 10.00 627.25 6,272.50
18.8.4 32 mm nominal dia Pipes Metre 20.00 739.30 14,786.00
Providing and fixing brass stop cock of approved quality
Digitally signed by AMIT
18.16.1 15 mm nominal bore Each 1.00 353.25 353.25
18.16.2 20 mm nominal bore Each 1.00 379.20 379.20
Providing and fixing gun metal gate valve with C.I. wheel of
approved quality (screwed end):
18.17.1 25 mm nominal bore Each 1.00 622.40 622.40
18.17.2 32 mm nominal bore Each 1.00 689.95 689.95
Providing and fixing C.P. bass angle valve for basin mixer and
5 18.53 geyser points of approved quality conforming to I.S:8931 a) 15
mm nominal bore.
18.53.1 15 mm nominal bore Each 1.00 574.30 574.30
Providing and fixing unplasticised P.V.C connection pipe with
PTMT Nuts coller and bush of approved quality and colour.
18.74.2 15mm nominal bore with 45cm length Each 2.00 121.90 243.80
Sub-Total of Water Supply Installation, Separate for Scheduled & Non-Scheduled Items 56,036.55 0.00
Digitally signed by AMIT
Summary of Low Voltage Items
S.No. Package Details QTY DSR Non DSR Total
1 Integrated Access Control System 1 294,734.00 74,600.00 369,334.00
2 Integrated CCTV SYSTEM 1 360,590.00 - 360,590.00
3 Integrated Audio Visual SYSTEM 1 - 4,862,310.00 4,862,310.00
Digitally signed by AMIT
SUB-HEAD - D - SPRINKLER PIPING & ACCESSORIES
SL. DSR DSR Rate DSR Amount
DESCRIPTION OF ITEMS UNIT Qty NS Rate (Rs.) NS Amount (Rs)
Providing, laying, testing & commissioning of 'C' class heavy
duty MS pipe conforming to IS 3589/IS 1239 including Welding,
fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc.
1 27.7 and fixing the pipe on the wall/ceiling with suitable
clamp/support frame and painting with two or more coats of
synthetic enamel paint of required shade complete as required
Supplying, fixing, testing and commissioning of butterfly valve of
PN 1.6 rating with bronze/ gunmetal seat duly ISI marked
complete with nuts, bolts, washers, gaskets conforming to IS
13095 of following sizes as required :
Providing and fixing ISI Marked of approved make Fire
4 NS Extinguishers complete with all accessories as per
manufacturer's specifications.
4.1 CO2 gas nozzle type - 9 Litre capacity (IS:15683). NOS 1.00 12,070.00 12,070.00
4.2 Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683). NOS 1.00 2,740.00 2,740.00
4.3 ABC dry powder stored pressure type 6 kg capacity (IS:15683). NOS 5.00 4,437.00 22,185.00
Providing, fixing, testing & commissioning of 15mm dia
5 quartzoid bulb type sprinklers of rating 68 degree centigrade
with required accessories :
5.4 27.21.4 Concealed Sprinkler NOS. 29.00 1,553.00 45,037.00
Digitally signed by AMIT
Supplying, installation, testing & commissioning of sprinkler
flexible pipe (UL Listed) of stainless steel complete with 15 NPT
on reducer thread with maximum working pressure of 175 PSI
6 test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT
male thread to sprinkler head (Outlet) 15mm NPT female thread
with reducer, nipple, 2 side brackets, center bracket, stockbar
of following sizes complete as required.
Providing and fixing signages printed on photoluminescent
U1000 aluminium sheet of 1.0 mm (+ -10%) containing lumigen II
as base chemical, covered under UV stablized coating and of
appropriate size including fixing on wall, door, ceiling etc. with
proper clamps, hangers, cleats anchor fasteners etc. complete
in all respacts as diercted by Engineer-in-charge
TOTAL CARRIED TO SUMMARY 426,972.00 56,195.00
Digitally signed by AMIT
Schedule of Qunatities: Integrated Access Control System
S No DSR E&M 2025/MR Item Description Qty Unit Rate DSR Amount NDSR Amount
Access Control System with Face recognition Supplying, Installation, Testing
and Commissioning of Access Control System comprising of Face and
fingerprint Recognition, Smart Card, QR Code, NFC & PIN Code based Reader,
following sizes of 5” IPS TFT Touch Screens, 1GB RAM, 8 GB ROM, Live Face
Detection with anti-spoofing against 2D photograph, mobile selfie & video,
Fake Fingerprint and face Detection Technology, 30,000 Face storage (1:N) /,
3,000 fingerprint (1:N), QR code 30,000, 30,000 card storage (1:N), 2 lakh
transaction storage, 20,000 image logs, onboard dual camera (colour & IR)
Primary camera min 2MP, Support authentication & verification from up to 1
meters, Communication protocols WiFi, TCP/IP, Wiegand Out, Wiegand IN,
USB, MQTT protocol, Blacklist Employee Management, User wise
authentication modes; Built in Lock Control, Mask Detection & Alert
(configurable), 40 to 30,000 lux illumination, IP65 for Ingress Protection,
Certification: CE, FCC, BIS, ROHS, etc. Metal Enclosure with battery backup,
suitable for mounting on metal surface/metal frames/ wooden
frames/wall/flap barriers including all mounting bracket & accessories
complete etc. as required.
1.1 41.1.1 5" IPS TFT Touch Screen 3 Each 58,306.00 174,918.00
Software for Web based Access Control System Supplying, Installation, Testing
and Commissioning of Web based Access Control Enrolment and Device
Configuration Software, Should be independent of OS (Windows), Unified
Management of Biometric, Card, and Controllers, Import Functionality for bulk
user details, Biometric Template Retrieval for Data Recovery, User
2 41.5 Management, Logs and Terminal Management, Support for IP-based and USB 1 Nos 97,176.00 97,176.00
Biometric Devices, User-specific Access Policies, Different User Policies on the
Same Terminal, Assignment of Specific Access Schedules, Pushing Users to
Terminals or Groups, Admin Authority Management to define rights of each
user to perform, Blacklist User Management, Access Schedule Creation, Real-
Time Log Retrieval, Real- Time User Identification, Secure Storage of
Biometric/Users Data, Capable to integrate with 3rd party applications over
Web API's, MQTT protocol support
Electromagnetic locks Supplying, Installation, Testing and Commissioning of
Electromagnetic locks (fail safe type) for following type of Doors suitable for
3 41.6 operation on 12 V DC having holding force 600 lbs for Single Leaf Door and
1200lbs for Double leaf door with suitable feedback i/c connection complete
etc. as required.
Digitally signed by AMIT
41.6.2 Double leaf door (Each leaf 600lbs & Total 1200 lbs) 1 Nos 7,593.00 7,593.00
Exit Push Button
Supplying, Installation, Testing and Commissioning of Heavy Duty SS Finish Exit
Push Button for releasing access doors with all necessary installation
accessories i/c connection complete etc. as required.
Door Position Sensor
5 41.8 Supplying, Installation, Testing and Commissioning of Door Position Sensor i/e 3 Nos 622.00 1,866.00
connection complete etc. as required.
Supply, Installation, Testing & Commissioning of Smart card Frequency
Excitation (13.56 MHz) Mifare smart Card , distance upto 2.5" Memory Type
6 MR EEPROM, 2K bit memory Complies with ISO/IEC standards for thickness. 100 No. 452.00 45,200.00
Lifetime Warranty .etc. as per specifications of this tender etc complete as
required and directions of Engineer-in- Charge.
Supply, Installation, Testing & Commissioning of 3 core 1.5 Shielded
7 MR communication multi-stand Data Cable etc. as per specifications of this tender 200 Mtr 147.00 29,400.00
etc complete as required and directions of Engineer-in- Charge.
Digitally signed by AMIT
SCHEDULE OF QUANTITIES: IP Based CCTV System
S NO DESCRIPTION
Supplying Installation Testing and Commissioning of 5/6MP IP IR Dome Camera having following specifications and features etc :- 1)Type of Camera: Dome Camera 2) Image Sensor: 1/2.8" or better progressive Scan CMOS get color image even
at night condition 3) Signal System: PAL/NTSC 4) Minimum Illumination: 0.008Lux@ F1.4, AGC ON, 0 lux with IR or better 5) Imaging: 1/3s to 1/30000s Shutter Support, Auto Gain Control , White Balance- Auto, Back Light Compensation, Multi
zone Privacy Masking, HLC, Digital Watermarking. 6) On Screen Display: Camera should display Camera title, Date & Time in live & recorded video both. 7) Signal to Noise Ratio: > 50 dB 8) Day & Night: True Day & Night High Performance
Mechanical IR cut filter with auto switch, IR Source Inbuilt IR LED's with effective distance upto 50 Mtrs integrated IR 30 Mtrs for colour view in night. 9) Video Compression (Minimum): H.265 or better, Audio:- G.711U/A, G.711Mu, G.726, AAC,
G.723 10) Wide Dynamic Range: WDR (120dB or more) 11) Digital Noise Reduction: DNR (2D/3D) On/Off 12) Streaming: Triple streaming, configurable 13) Video Streaming & Frame Rates: Triple streaming , configurable Main stream: 5/6MP
@25/30 fps, Sub streams: D1@25/30 fps or better 14) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable through client software or web browser 15) Profile Management: User configuration import, export 16)
Security: User Authentication, Water Marking 17) Onboard Storage: Camera should support built-in Micro SD/SDHC/SDXC Card slot upto 512 GB. It should be supplied with minimum 128GB memory Card. 18) Recording Management: Format SD
overwrite, storage management, video to NAS device, 19) Edge Analytics : Tripwire, Intrusion, Motion Detection 20) Alarm Trigger : Motion/tampering detection;network disconnection detection; IP conflict detection; memory card state
detection; memory space detection 21) Alarm Support: It should have 1/1 Alarm In/ Out Port
22) Audio Support: It should have 1x Built-In Mic and 1/1 Audio In/ Out Port for external Mic. and Speaker (As per site requirement) with G.711U/A/ G.711Mu/ AAC/ G.726 audio compression
23) Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP, SMTP, RTSPS, unicast,
24) System Capability: ONVIF
25) VMS: Camera shall support open source VMS
26) Cyber Security: trusted boot, AES 256-bit Encryption, Configuration encryption, trusted execution, Digest, security logs, , account lockout, video encryption, IP/MAC filtering, HTTPS, trusted upgrade.
27) Ethernet: 1 RJ 45 10/100 Ethernet port
28) Power Input: The camera should support simultaneous dual power input—12 VDC (via power adapter) and PoE—to ensure continuous operation in the event of a failure in one power source.
29) Power Requirement: 12VDC/24VDC/PoE (802.3af)/ePoE
30) Enclosure: IP67 weather proof, IK10
31) Operating Condition: Ambient Temperature:- (-) 05°C to 50°C, humidity 95% (max) (non-condensing)
32) IR life: 40000 hours or higher
33) Video Bit rate: 32 KBPS - 8 MBPS or better
34) Standards: BIS with ER, STQC Certified, CE, FCC and RoHS
1.1 40.5.2 5MP/6MP IP IR 2.7 to 4 mm ~12 to 13.5mm or better Varifocal Motorized lens Dome Camera.
Supplying Installation Testing and Commissioning of following Channel Network Video Recorder (NVR) with camera licenses to record for all channels having specifications and features etc as mentioned below:
1) Network Video Recorder Embedded/ Installed OS (Linux) along with Camera Licenses to record per NVR and to provide a live view, storage and simultaneously Multi-channel playback of all IP camera or more and must b
ONVIF with minimum support of 384 Mbps incoming Bandwidth.
2) NVR should support video compressions : H.265 or better, H.264, MJPEG.
3) Must support 1 channel RCA Input, 2 channel RCA Output for Two-way Talk with G.711U/A, G.711u, PCM, G726 audio compressions.
4) Intelligent auto power on when power resumes after power outage.
5) Storage: It should support minimum 8 SATA Slots with 20TB capacity/ Slot and RAID support of RAID 0/1/5/6/10.
6) Connectivity Interface : 2 Nos. x 10/100/1000 Mbps Ethernet Ports, 1x RS485, 1x RS232, 1x eSATA Port
7) Backup Interface : Its should have 4 Nosx USB port (2x USB3.0, 2xUSB2.0)
8) Video Output Ports: 2x HDMI and 2 VGA
9) Alarm Ports: It should have 16/8 Ch In/ Out ports to connect various type of external sensors and output devices like hooter/ Siren etc.
10) Email & SMS Altert options: Option for SMS/ Email Alerts to minimum 5 designated mobile number for power failure, HDD failure, vandalism, tempring, network disconnection and panic
2 40.11 11) Web & Mobile Application: Web, Mobile app (For iPhone, iPad, Android Phone) for alerts and viewing.
12) Protocols: HTTP, HTTPS, TCP/IP, IPv4/IPv6, UDP, DHCP, DNS, SMTP, UPnP, IP Filter, PPPoE, FTP, DDNS, Alarm Server, IP Search, Multicast, Auto Registration, ONVIF (Profile T, Profile S, Profile G), CGI, SDK and
OEM Cloud for remote monitoring without any public IP need.
13) Standards: CE, FCC, RoHS, BIS Certified
14) Power Supply : Should support AC100-240V, 50/60Hz Power supply.
15) Operating Condition: -5°C to 50°C, humidity 90% (max) (non-condensing)
16) The VMS application shall support all the features & functionalities of the offered cameras.
17) VMS should consist Licenses for all channels to record Cameras with General, motion detection, intelligent, alarm and POS recording modes. VMS should be provided with Camera Licenses, with no dependency of VMS
licenses by binding with the MAC address of the cameras to achieve the functionality.
18) The NVR OEM shall be responsible for providing a mobile application compatible with both Android and iOS devices, enabling remote monitoring and playback of cameras/NVR footage.
19) The OEM must provide its own DDNS server hosted in India, eliminating the need for a public IP address for remote monitoring over the Internet.
20) Must support Continuous, Alarm, Motion, Instant, Panic Recording Mode
21) It should support Resolution: 32MP; 24MP; 16MP; 12MP; 8MP; 5MP; 4MP; 1080p; 720p; D1; CIF; QCIF
22) When alarm recording is enabled and an event occurs, you can click the alarm icon on monitoring page to view the alert details. The snapshot function is supported on monitoring and playback page
Digitally signed by AMIT
2.1 40.11.1 32 Channel Network Video Recorder (NVR) having display split :- Main screen: 1/4/8/9/16/25/32(36), 2nd screen: 1/4/8/9/16
Supplying, Installation, Testing and Commissioning following capacity Serveillance grade Hard Disk with upto 256MB/s Transfer Rate, 256 MB Cache, 7200 RPM Disk Speed, 3.5 inch form factor, SATA Interface, BSMI, ICES
003/NNB-003, CE, FCC, KC, Maghreb, RCM, UKCA, VCCI, CB-Scheme, TUV, UL Certifications.
4 40.12.4 10TB (Terabytes)
Supplying, Installation, Testing and Commissioning of following size LED display (LED monitor) industrial grade with 3840x2160 resolution or better, USB playback, bluetooth and miracast connectivity, 4X HDMI 2.0, DP 1.2,
5 42.4 HDR 10/10+, brightness: 500-nits or better, Video wall mode should be available, contrast ratio: 1200:1, OPS slot, viewing angle (H/V): 170°/ 170°, response time less than 12ms, Display control shall be on monitor screen an
programmable with remote (remote shall be supplied with system), Key Board, Optical Mouse, etc. as required.
5.1 42.4.3 55 inch or larger
Digitally signed by AMIT
Furniture Quotation
S. No. Product Description Image Qty Rate Amount
SLICE HIGH BACK CHAIR
1) High Back Leaiheriie chair
2) Aluminum Cushioned Arms
3) Syncrotilt Mechanism with 3 Point Locking
4) Pneumatic Seat Height Adjustment
3) Aluminum base with 60mm Nylon Castor
Supplying and placing in position leatherette executive medium back chair size :- (w)720mm x (d)560mm x (h)1065mm. seat depth 500mm. seat width
560mm. back height 560mm. beautiful in its simplicity, our collection welcomes you with its gentle curves and ergonomic comfort. tailored to perfection in
sumptuous leatherette. all while adding refined sophistication to your modern workspace. mechanism synchro single locking, function revolving,
adjustable height, tilt tension control. ergonomic design helps maintain posture for better productivity. buttery soft leatherette looks and feels opulent.
padded seat, high backrest, and padded armrests offer a comfortable seating experience. pneumatic height adjustment lets you match the desk height. tilt
tension control lets you increase or decrease the resistance while you recline. synchronize recline up to 145 degree with single locking position offers a
personalized comfort. 120 kg load-bearing capacity ensures stability and security for the user. a sturdy metal base ensures longevity, all while elevating the
1 Reception Chair aesthetic. high-quality castors ensure smooth noise-free movement. 1 30900 30900
Size : 1950W x 750D x 710mmHt
Made of fabric upholstry with metal legs
Fabric considered as per our standered
Supplying and placing in position a upholstered lounge sofa,. the internal framework shall be constructed from 12 mm thick, anti-termite-treated plywood
(tentatively grade 303 as per indian standards for commercial, common, and moisture-proof plywood) with a controlled moisture content of less than
10–12% to ensure long-term structural stability and durability. the under-structure frame shall further incorporate 12 mm thick kiln-dried german steam
beech wood, selected for its superior strength and resistance to warping, thereby enhancing the overall durability of the sofa. the seating base is to be fitted
with a high-quality web suspension system that provides resilient support and ensures lasting seating comfort. all joints in the structure must be firmly
bonded using super bond adhesive and reinforced with star screws, wooden pins, and stapler pins to maintain long-term joint integrity under regular usage.
the sofa design features a panelled back and cushioned armrests to promote comfortable lounging, with the entire structure padded using high-resilience
polyurethane (p.u.) foam of 32 density. the seat shall include 40 mm thick stack foam, while the backrest and armrest cushioning shall also utilize 40 mm
thick foam, all securely fixed using adhesive super glue. the final foam assembly will be upholstered in premium yellow 54-pattern leatherette, selected for
its premium feel, aesthetic appeal, and ease of maintenance. the sofa shall be complemented by stylish sleek mild steel (ms) legs .
2 Sofa Reception Area 1 95000 95000
3 Bench Seat Reception Area 1
Size : 900mmDia x 450mmHt
Made of top 18mm thick prelam particle board (Action tesa) with wooden legs
Supplying, and placing in position of center table. the ct collection is destined to become a centerpiece of your modern Indian homes. Perching on solid
wood trestle legs, the veneer tabletop is tastefully adorned with brick pattern, crafted to perfection by skilled Marquetry artisans.Tabletop crafted of
premium engineered wood wrapped in Steam Beech veneer in Wenge finish.Veneer features brick patterns, masterfully crafted by skilled Marquetry
artisans.Legs are crafted of kiln-dried solid wood for added durability.Material & Subtype Veneer,Solid Wood - Steam Beech Wood, Table Top Thickness
4 Center Table 36mm,Colour & Colour Family Brown - Wenge. 1 9200 9200
5 Open Display Shelf Size : 700W x 750D x 2400mmHt Made of 18mm thick prelam particle board (Action tesa) with open shelfs 1 29588 29588
5 Bench Seating 2-Seater Size : 1500W x 800D x 450mmHt Made of fabric upholstry with metal legs Fabric considered as per our standered Table : 400mmDia x 450mmHt Made of 18mm
1 thick prelam
48750 particle board
48750with pole stand
CONFERENCE AREA 0
Size : 3300W x 1500W x 750mmHt (Top in 2 parts)
Top and Gables : 36mm thick prelam particle board (Action tesa)
Modesty : 18mm thick prelam particle board (Action tesa)
Electrical : 2-nos access flap on the top considered
Supplying, and placing in position of conference table . The table top are made out of 36mm thk Prelam Particle board table top with 2mm thk pvc edge
banding.Table top supported with 36mm Side panel & 18mm thk Modesty panel with 2mm thk PVC edge banding.Providing metal wire raceway & junction
connectivity of wires & cables also having a provision of 6 Module Flip top cover.
5 Conference Table Hillite Mid Back Chair 1 82000 82000
1) Mid Back – Mesh Chair
2) Adjustable Armrests (Up & Down)
3) Adjustable Lumbar Support
4) Synchro Tilt Mechanism with One Point Locking
5) Mesh Back & Seat Fabric Tapestry
6) Pneumatic Gas Lift
7) Chrome Base with 60mm Nylon castor Wheel
"Supplying, and placing in position of high back chair . Medium Back Office Revolving Chair
With Cushioned Seat And Adjustable Armrest. Back:- Upholstered With Mesh Seat:- Plywood Hot Compressed Upholstered With Fabric.Armrest:- 2D
Adjustable With Pu Pad, 1D Handle ( Grey ) With Pu Pad ( Black )
6 Conference Chair Mechanisam:-Synchro With Single Locking And Tension Adjustment.Base:- Nylon Base . " 2 11500 23000
Digitally signed by AMIT
7 Conference Chair Made of fabric upholstery with Nylon legs as per image Fabric considered as per our standard 10 12500 125000
8 Bench Seating Conference 2-Seater Sofa Size : 1675mmWidth Made of fabric upholstry with metal legs Fabric considered as per our standered Table : 300mmDia x 450mmHt Made of 18mm thick2 prelam particle
68500 board with
Size : 1050W x 450D x 2100mmHt
Made of 18mm thick prelam particle board (Action tesa) with openable shutters
Supplying, and placing in position of full height storage @ 1800mm height as per photograph/drawing . The storage unit having Openable shutters with
shelf in it. The modular storage unit top shall be made from 18 mm thick pre-laminated particle board and rest of the sides as well as shelves and shutter to
be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-laminated particle board. All edges to be provided with 2
9 FHS mm thick PVC lipping. The storage unit having openable shutters with D shape handles & locking arrangement.. 1 23888 23888
WORKSTATION AREA 0
10 LHS-1 Workstation Area Made of 18mm thick prelam particle board (Action tesa) with opeable shutters 1 40775 40775
11 LHS-2 Workstation Area Size : 3255W x 520D x 1050mmHt Made of 18mm thick prelam particle board (Action tesa) with opeable shutters 2 44852.5 89705
12 LHS-3 Workstation Area Size : 3550W x 520D x 1050mmHt Made of 18mm thick prelam particle board (Action tesa) with opeable shutters 1 48930 48930
13 FHS Workstation Area Size : 2100W x 450D x 2100mmHt Made of 18mm thick prelam particle board (Action tesa) with opeable shutters 1 47775 47775
14 Planters Workstation Area Size : 1200W x 800D x 1200mmHt Made of 18mm thick prelam particle board (Action tesa) with openable shutters 2 21040 42080
15 Workstation Chair 1) Mid Back Mesh Chair 24 9400 225600
16 Workstation Y-shaped Top : 25mm thick prelam particle board (Action tesa) 18 22400 403200
17 Linear Workstation Top : 25mm thick prelam particle board (Action tesa) 4 13700 54800
18 Pedestal Size : 400W x 450D x 650mmHt Made of 18mm thick prelam particle board (Action tesa) with 2-drawers and 1-filling 24 5850 140400
19 Cabin Table Cabin 1-5 Top & Gable end : 25mm thick prelam particle board (Actio tesa) 5 28500 142500
20 Back Storage Cabin-1 Made of 18mm thick prelam particle board (Action tesa) with opeable shutters 1 15844 15844
21 Back Storage Cabin-2 Size : 690W x 450D x 750mmHt Made of 18mm thick prelam particle board (Action tesa) with opeable shutters 1 6094 6094
22 Back Storage Cabin-3-4 Size : 2100W x 450D x 750mmHt Made of 18mm thick prelam particle board (Action tesa) with opeable shutters 2 17063 34126
23 Back Storage Cabin-5 Size : 900W x 450D x 750mmHt Made of 18mm thick prelam particle board (Action tesa) with opeable shutters 1 7313 7313
24 Cabin Head Chair Cabin 1-5 2) Adjustable Armrests (Up & Down) 5 9500 47500
25 Cabin Visitors Chair Cabin 1-5 2) Adjustable Armrests (Up & Down) 10 8600 86000
Grand Total 2,403,622.24
Grand Total 2,403,622.24
Digitally signed by AMIT
Schedule of Quantities: Integrated Audio Visual System
Total Qty Unit rate Total
Sr No Item Description UoM
SITC of 86" 4k, UHD Professional Signedge Display with 500 NITS, 24*7 ,Built in SOC/ Media Playerwith Quad
Core Processor, Built in Open Platform Android 11, 3X HDMI, Audio Input Audio Output, Built in Speaker(12W x 2)
;Including mounting bracket, Built-in Chromecast, Dolby Digtial audio HDMI-CEC device linking supported, 3
USB(2.0), 3*HDMI(2.0 Side), Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Wifi,CPU Built in Mali G31
MP2 GPU-A55*4, 1.1 GHz Processer, 4 GB RAM 32GB Storage,Metal Frame 12 W built speakers, With 3 years
1 on Site Warranty No's 1 395,000.00 395,000.00
SITC of 75" 4k, UHD Professional Signedge Display with 400 NITS, 24*7 ,Built in SOC/ Media Player with Quad
Core Processor, Built in Open Platform Android 11, With Built in Bluetooth, 2X HDMI, Audio Input Audio Output,
Built in Speaker(10W x 2) ;Including mounting bracket, Built-in Chromecast , HDMI Arc, Dolby Digtial audio, The
built-in SOC is powered by Google's Android Platform, HDMI-CEC device linking supported, 2 USB(2.0),
3*HDMI(2.0 Side), Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Wifi,CPU Built in With Cortex-A55*4,
2 1.1 GHz Processer, 2 GB RAM, 20 W built speakers, With 3 years on Site Warranty No's 1 215,000.00 215,000.00
SITC of 43" 4k, UHD Professional Signedge Display with 400 NITS, 24*7 ,Built in SOC/ Media Player with Quad
Core Processor, Built in Open Platform Android 11, With Built in Bluetooth, 2X HDMI, Audio Input Audio Output,
Built in Speaker(10W x 2) ;Including mounting bracket, Built-in Chromecast , HDMI Arc, Dolby Digtial audio, The
built-in SOC is powered by Google's Android Platform, HDMI-CEC device linking supported, 2 USB(2.0),
3*HDMI(2.0 Side), Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Wifi,CPU Built in With Cortex-A55*4,
3 1.1 GHz Processer, 2 GB RAM, 20 W built speakers, With 3 years on Site Warranty No's 5 77,500.00 387,500.00
SITC of Fixed Wall Mount, capable of holding up to 75 kg and supports 37" to 100" displays, VESA Compliant etc
4 all complete No's 7 10,780.00 75,460.00
SITC of Cable Cubby with flip top, cover and 6 Pass Through Holes for multi-format cables, 2 Universal Power
5 Socket , 1 HDMI, 1 USB-C for Data Transfer, made of aluminium etc all complete etc all complete No's 2 35,950.00 71,900.00
SITC of 4K PTZ Conference camera with minimum 20x optical zoom & 60-degree horizontal coverage. Low Noise
CMOS 4K image sensor with User-configurable resolution and quality for IP streams (up to 1080p). HDMI
resolutions up to 4K30 or better. Image rotation controls to allow for inverted mounting using ceiling bracket.
Minimum Illumination - 0.5 Lux @ (F1.8, AGC ON) or better, Horizontal Rotation Range - ±170°, Vertical Rotation
Range - -30° to +90° or better, White Balance controls- Auto, indoor, outdoor, one-push, manual, specified color
6 temperature or better. Power – PoE & AUX. Shall include wall mounting bracket included. No's 1 655,670.00 655,670.00
Digitally signed by AMIT
SITC of 4-Input 4K Wireless Presentation and Conferencing System with Matrix Outputs, USB 3.0, Multiview &
Wireless Casting, Automatic or manual switching of 4 connected sources (2 HDMI & 2 USB-C) with assignable
USB host connection, 60W PD on the USB C Ports, Supports input resolutions up to 4K30 4:4:4 via USB-C or
HDMI Inputs: 2x HDMI In: 19-pin Type A, 2x USB-C, Wireless Video from Airplay or Miracast Source and casting
dongle (1 dongle included), Outputs: 2x HDMI Out: 19-pin Type A, 1x Analog Audio Out, Video Resolutions (Max):
HDMI Out 1 – 3840x2160p @60Hz 4:4:4, HDMI Out 2 – 3840x2160p @30Hz 4:4:4, USB: 3x USB 3.0 Type A
device ports | 5v 10000mA per port, 2x USB 3.0 Type B host ports (assignable), RS-232: 1x 4-pin Phoenix (API
control) | Provides 12V Power, LAN: 3x 8-pin RJ-45 Ethernet Ports, Wireless: 4x Wi-Fi Antennas | IEEE 802.11
a/b/g/n/ac | Dual-band 2.4 & 5GHz | WEP, TKIP, AES, WPA, WPA2, Built-in USB 3.0 hub for connection of
peripheral devices such as speakerphones or cameras, USB-C input supports alt-mode for both A/V, Ethernet,
and Data communication over a single cable, Built-in wireless access point for secure and isolated communication
to screensharing devices, Wireless access point supports custom SSID, password and screensharing access PIN
7 etc all complete No's 1 395,000.00 395,000.00
SITC of Ceiling Tile Beamforming Microphone with Integrated DSP comprising minimum 128-element MEMS
microphone array with beamforming and advanced algorithms including AEC, AGC, ANS, AFS, and reverberation
reduction. The unit shall provide frequency response of 75 Hz to 20 kHz, 48 kHz/24-bit sampling, signal-to-noise
ratio of 70 dB or better, and support balanced analog and Dante network audio outputs. The microphone shall
support 2 × 2 Dante channels, RS-485 control, and 12 V DC / 48 V phantom power or PoE. The unit shall be
8 suitable for flush or suspended ceiling mounting and supplied complete with all required accessories. No's 1 675,670.00 675,670.00
SITC of Audio, Video and Control (AV&C) Processor, 64 x 64 networked audio channels, 8x on-board Flex
channels and GPIO, Full-featured Control engine (with feature license), 8 AEC Processors, up to 32 x 32 Dante
audio channels (8 x 8 included), USB AV bridging (8 x 8 audio + Camera support), Full-featured Q-SYS Control
9 engine (with optional feature license), External USB audio device host, Up to 2x VoIP instances etc all complete No's 1 615,650.00 615,650.00
Supply, Installation, Testing & Commissioning of Hardware or Software based control system with required ports
to control the devices mentioned in BOQ with perpetual licenses to connect Wall/Table mount touch screen
controllers and iOS and Windows devices as wireless touch controller. The control system should support
minimum 5 touch control devices. Noted: Required Hardware / Perpetual Software should be added to meet the
requirement and match the compliance. All Hardware & Software should be from the same OEM for the
10 interoperability. No's 1 214,560.00 214,560.00
SITC of 6.5-inch, 2-Way Ceiling Speaker, Rated Power: 30W, Frequency Range: 65 Hz – 20 kHz, Sensitivity: 88
dB, Rated Coverage 135° conical DMT, Maximum continuous SPL 106 dB, Nominal impedance: 8 / 16 Ohm,
Transformer taps: 30W / 15W at 100 / 70V, IP-34 Rated, Low-saturation and low-loss 70/100V transformers with
11 16Ω bypass, UL and CE Certified etc all complete No's 6 39,900.00 239,400.00
SITC of 4 Channel Class-D Amplifier, Power (per channels driven): 200 W at 8 Ω / 4 Ω / 100V / 70V, FlexAmp
Technology, Frequency Response: 20 Hz – 20 kHz, Signal to Noise > 103 dB, Input impedance >10k, balanced or
12 unbalanced, User-configurable operating modes, UL, CE, RoHS/WEEE compliant etc all complete No's 1 275,650.00 275,650.00
SITC of 10.2" Apple iPad LED-backlit Multi-Touch display with IPS technology with User Control Interface (UCI)
13 Deployment etc all complete No's 1 69,950.00 69,950.00
14 SITC of 24-Port Gigabit PoE+ Ethernet Smart Switch with 2 SFP Ports and Cloud Management etc all complete No's 1 94,500.00 94,500.00
Digitally signed by AMIT
SITC of 2 Meter Premium High Speed HDMI 2.0b Flexy Cable, Bandwidth up to 18Gbps, Up to 4096x2160@60Hz
at RGB 4:4:4 video resolution, High Dynamic Range (HDR10), Dolby Vision and Hybrid log–gamma (HLG) video
15 etc all complete No's 12 3,250.00 39,000.00
SITC of 10 Meter Active Copper HDMI Cable, Data Rate: Up to 18.2Gbps, Colour Depth: Up to 16 bits, Colour
Formats: RGB 4:4:4 / Y’CBCR 4:2:2 / Y’CBCR 4:2:0, Consumer Electronic Control (CEC), Auto Lip-Sync
Correction, Audio Return Channel (ARC), Enhanced Audio Return Channel (eARC), High Dynamic Range (HDR)
16 etc all complete No's 6 20,000.00 120,000.00
SITC of 2 Meter USB Full-Featured Type-C cable for USB 3.1 Gen2, 4 Lane Displayport Alt mode (4K60FPS
Video and Audio), Supporting peripherals via USB 2.0 up to 480 Mbps (Mouse, Keyboard, Thumb Drive,
17 Speakerphone and Webcam) etc all complete No's 6 3,950.00 23,700.00
18 Webcam, SSD storage, Native USB2/USB1 and USB3 extension, Plug and play compatible with PC, Mac, and No's 2 27,500.00 55,000.00
19 jacket (as per actual) etc all complete Meter 100 225.00 22,500.00
20 SITC of Mirophone cable PVC/Nylon insulation, PVC jacket (as per actual) etc all complete Meter 50 315.00 15,750.00
21 SITC of Category 6A Cable, 4 Pair, S/FTP, PVC jacket (as per actual) etc all complete Meter 100 382.00 38,200.00
22 SITC of Various Cables, relay modules & Connectors etc all complete No's 5 25,950.00 129,750.00
23 2 no Shelfs to mount the equipments which are not rack mounted, 8X2, 5/6 Amp. Power Distribution Unit, Cable No's 1 37,500.00 37,500.00
Digitally signed by AMIT
Schedule of Quantities: Integrated IT ACTIVE
S No DSR E&M 2025/ MR Item Description UoM QTY Rate DSR Amount NDSR Amount
Supplying, installation, Testing and commissioning of following capacity 24 port Layer 2 indoor
Network Switch having features and specifications etc. as mentioned here under: At least 24 X RJ-
45 Gigabit Ethernet Ports and additional 2 X 10G Base -T with 4 X SFP Ports with non-blocking
architecture by having Switching capacity of min. 168Gbps and packet forwarding rate of 125Mpps
or higher, 16K MAC table. Console Port, USB port, Stacking support of min. 8 units per stack.
Internal dual AC Power supply, STP, RSTP, MSTP, BPDU Filter, BPDU Restriction, Min. 9K Jumbo
Frame, LBD, IGMP Snooping V1/V2/V3, MLD Snopping V1/V2. IGMP /MLD Groups 1K or more,
IPv4/IPv6 Loopback Interface, 16 L3 IP Interface, Ipv6 ND, VRRPv3, UDP Helper, ECMP. VLAN:
1 39.3 802.1Ǫ, Port based, Ǫ-in-Ǫ, Multicast VLAN, Protocol VLAN, VLAN Trunking, DHCP Snopping,
Server, server Screening. RADIUS , TACACS+ Authentication, ǪoS: 802.1P, 8 queues per port,
ǪoS : WRR, Strict+WRR, WRED, 802.1p. ACL: MAC based, IPv4C IPv6, TCP/UDP Port number,
time based ACL, TFTP Client, SNMP V1, v2c, v3, SNMP traps, RMON, DHCP server, relay, client,
LLDP, LLDP-MED, OAM, Dying Gasp, 802.3ah, sflow, RIP, OSPF v2/v3, policy based route, SSL,
SSH. 6 kV surge protection on all Gigabit Ethernet ports and on all GE RJ-45 access ports.
Certifications: UL, CE, FCC, RoHS, MTCTE, OEM/Product must be on Trusted Telecom Portal of
Department of Telecommunication, Government of India etc. complete as required.
24 port PoE Layer 2 Network Switch with PoE Support of 370W or higher with each copper port
supporting 802.3at PoE+ min.
39.3.2 24 port Layer 2 Non-PoE Network Switch Nos 5 86,163.00 430,815.00
Supplying, Installation, Testing and commissioning of small form-Pluggable (SFP) for Network
Switches. Must be hot Pluggable, RoHS Complaint, etc. complete as required.
39.6.3 10 G SFP + Single Mode/Multi Mode Nos 2 14,972.00 29,944.00
Supplying, Installation, Testing and commissioning of indoor Wireless Access Point for Wi-Fi 7
technology - high throughput, low latency, and extended range • Manageable Platform ONETM,
IQ/Controller • Reduced mean time to resolution with AI • ZTNA policy enforcement, Fabric
integration AP Radio Features Five-Radio Design • 2.4 GHz (4x4:4) • 5 GHz (4x4:4) • 6 GHz (4x4:4)
3 MR • IoT Radios Operational Modes • Mode 1: 2.4 GHz /5 GHz/6 GHz data radios • Mode 2: 5 GHz/6 Nos 3 246,171.00 738,513.00
GHz data radios + trifrequency sensor • Mode 3: 5 GHz/5 GHz + 6 GHz data radio • Mode 4: 2.4
GHz/5 GHz + tri-frequency sensor • Mode 5: 5 GHz/5 GHz + 2.4 GHz data radio • Mode 6: 6 GHz/6
GHz + 5 GHz data radio 2x2 Tri-Frequency Sensor etc. complete as required.
SITC of workstations Intel Core™ i7 14th generation processor Windows 11 Pro 16 GB DDR5 RAM
512 GB SSD Solid State Drive with windows pro 11 along with 20"-24" screen etc all required.
Digitally signed by AMIT
Schedule of Quantities: IT PASSIVE
S No 2025/ MR Item Description UoM QTY Rate DSR Amount NDSR Amount
Supplying, Installation, Testing and commissioning of following
CAT6A Patch Cord should have ETL/UL verification program
certificate for compliance with ANSI/TIA-568.2-D etc. complete
39.13.1 Copper Patch Cords of length 1m (3ft) Set 98 173.00 16,954.00
39.13.2 Copper Patch Cords of length 3m (10ft) Set 98 405.00 39,690.00
Supply, Installation, Testing and Commissioning of loaded
Patch Panel 24 Port Cat 6A U/UTP ,The Cat-6Atransmission
performance is in compliance and Exceeds ANSI/TIA/EIA-
568.2-D Standard. Supports 1000-Base-T. 90 Degree (Top
Entry) or 180 Degree Punch Down Design for Convenient
Network Terminations, Individual replaceable jack module
panel design as applicable.UL Listed, Complaint to RoHS
2 MR Directive 2011/65/EU and (EU) 2015/863 and ASTM B 117 Nos 5 23,500.00 117,500.00
Certified. OEM should have ISO 9001:2015, ISO
14001:2015and ISO 45001:2018 or latest.All networking
passive material (Fiber Cable, Copper Cables, Networking
Racks and their connectivity components) should be from one
OEM make only for Data as per given Specification etc. all
Supplying, drawing, Installation, Testing and
commissioning of CAT6 UTP LSZH 23AWG Twisted Pair
Cable in existing conduit/ on surface, Category 6
Unshielded Twisted Pair, 4 pair should be complied as
per UL/ETL verification program for compliance with
ANSI/TIA-568.2-D standard. Outer diameter should be
in the range of 6.1mm nominal with Operating
Temperature Range : -5° to +60°C, Bending Radius :
< 4 X Cable Diameter at –5°C ± 1°C and Pulling Force
: 11.5Kg etc. complete as required.
Digitally signed by AMIT
Supply, Installation, Testing & Commissioning of
dual face plate having provision for one I/O along
with spring type shutter for dust proof, made of ABS
PVC plastic etc. complete as required.
Supply, Installation, Testing & Commissioning of
single face plate having provision for one I/O along with
spring type shutter for dust proof, made of ABS PVC
plastic etc. complete as required.
Supply Installation Testing & Commissioning of 1 uPVC Cable
4 MR Manager as per given specification etc. Nos 5 4,250.00 21,250.00
Supply, Installation, Testing & Commissioning of Mounting
5 MR Hardware pack of 10pcs as per given specification etc. all Nos 5 2,060.00 10,300.00
Supplying and fixing 42U Rack with 6 inch Castor wheels and
front brake Floor Standing Rack with Main Frame Pillar of
1.6mm CRCA Sheet with removable side panels, L- Shape
adjustable Vertical Mounting Rail of 2mm with 'U'Marking
completely knocked-down condition (CKD) Shape, fitted with 4
number cooling fans, minimum 8nos two line cable entry/exit
provision at top and bottom with rubber protection, Front door
5mm Toughened Glass with MS frame or MS perforated with
lock, Rear MS vented or perforated door, Powder coated Color-
RAL- 7035 or black, complied with UL & RoHS, 2 x 6 sockets
16A power distribution units, 3 numbers closed cable
organizer, Hardware mounting screws packet of 20 x 1
number, etc. complete as required.
Supplying, Installation, Testing and commissioning of CAT6A
Copper Information Outlet (IO) with face plate of color as per
site requirement, should have ETL/UL verification program
7 39.15 certificate for compliance with ANSI/TIA-568.2-D. All copper Nos 98 302.00 29,596.00
Cable and components should be from same OEM to maintain
compatibility and interoperability etc. complete as required.
Digitally signed by AMIT
Supplying, drawing, Testing and commissioning of Cat6A UTP
4 pair, 23 AWG solid copper cable in existing conduit/ on
surface, U/FTP, LSZH, Non-Plenum, Horizontal (solid) Cable
suitable for high speed data networking application supporting
upto 10Gbps over a 100 meter channel. The 4 Unshielded
Twisted Pairs (UTP) cable with color coded insulation for easy
indentification should have FLAME PROPERTIES i.e.
Flammability Test - IEC 60332-1, Smoke Density - IEC 61034,
LSZH standards compliance: ANSI/TIA-568 C.2, ISO/IEC
11801, IEEE 802.3an, RoHS. Delay Skew should be < 45NS.
The outer Cable Diameter should be 7.5 + 2 mm. Cable should
have been tested and verified by UL/ ETL etc. complete as
Supplying, Installation, Testing and commissioning of RJ45
Connector for CAT 6/6A Cables. RJ45 modular plug supports
9 39.16 4 twisted pairs, 8 positions, 8 connectors. Housing: PC, UL94V- Nos 98 9.00 882.00
2, transparent color, Use for 24- 26 AWG stranded wires etc.
complete as required.
Supplying and drawing following core Multi mode Fiber Optic
Cable having corrugated steel armoring, leser optimize 50/125
μm with HDPE jacket, LSZH (Low smoke Zero Halogen), Tight-
buffered or loose tube, maximum attenuation: < 3.5 dB/km at
850 nm, < 1.5 dB/km at 1300 nm, bandwidth > 2000 MHz-km
at 850 nm, > 500 MHz-km at 1300 nm compliance and
certifications: ISO/IEC 11801 Ed. 2.2, ANSI/TIA-568-C.3, ITU-
T G.651.1 RoHS compliant. Multi Mode Fiber shall be Central-
loose tube filled with Thixotropic jelly, duly following Standards:
ISO 11801, IEC 60793-1/60794-1-2, ITU-T-REC G.652D and
Telecordia GR-20-core, High quality Electro Chromium Coated
10 39.20 Corrugated Steel tape (ECCS ) and HDPE- Sheath, Operating
ambient Temperature should be – 5 0C to +50 0C and Storage
Temperature should be – 5 0C to +50 0C, Maximum
Attenuation ± 3.5 dB/km at Operational Wavelength 850 nm
and ± 1.5 dB / km at Operational Wavelength 1300 nm . type
of fiber should be 50/125 / G.652D & Refractive Index should
be 1.483/1.478, The value for Mode-filed, Cladding Diameter
50 ± 2.5 μm and 125 ± 1μm correspondingly i/c splicing &
marking etc complete as required.
39.20.1 6 Core Multi Mode Optical Fiber Cable meter 100 87.00 8,700.00
Digitally signed by AMIT
Supply, Installation, Testing & Commissioning of 6
Core Armoured single Mode Fiber optic cable,
Central Lose Tube With Jelly Compound, Corrugated
steel tape armoured, Heaving 1300 nm Wavelength in
the existing surface/ recessed Steel/ PVC conduit etc.
complete as required. 53400
MR Supply, Installation, Testing and Commissioning of Each 2.00 5,322.00 10644
MR Supply, Installation, Testing & Commissioning of Each 5.00 626.00 3130
Supplying and fixing of following sizes of medium
class PVC conduit along with accessories in
1.21 surface/recess including cutting the wall and
making good the same in case of recessed conduit as
Digitally signed by AMIT
SCHEDULE OF QUANTITIES: EPABX (TELEPHONE & INTERCOM SYSTEM)
DSR AMOUNT (RS.)
S NO 2025/MR DESCRIPTION Unit QTY RATE DSR (INR) NON-DSR (INR)
Supplying, installation, testing and Commissioning of IP based
voice communication system with 04 Port Voicemail, 04 Port
FXS, 04 Port FXO, 1 PRI Trunk lines (30 Channels) Circuit with
CLIP Facility, min 100 IP users License with provision for further
additions, 100 analog users, 01 Number IP based Operator
Console, 100 Party Conference, Speed Dial, Music on Hold,
Internal/ External ring difference, Call Barring, Call Pickup,
Redundant server in active -Active mode and as per technical
specification including supporting accessories etc complete as
required. The system should have valid TEC GR approval from
Supplying, Installation, Testing & Commissioning of Type 1 IP
Phone having 2 VoIP account, 120 x40 DOT matrix screen with
backlight, Full HD duplex speaker phone, IPV6, Gigabit
Etherent, PoE etc. complete as
Digitally signed by AMIT
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
NIT ICMR.pdf
Tender Document
BOQ ICMR.pdf
Tender Document
scc icmr.pdf
Tender Document
GCC 2026.pdf
Tender Document
Instruction to Bidder for online Bid Submission.pdf
Tender Document
updated forms.pdf
Tender Document
3D ICMR.pdf
Tender Document
MAKELIST.pdf
Tender Document
Download all tender documents and submit your bid