CONSTRUCTION OF GOVERNMENT COLLEGE OF NURSING AT YADGIR, YADGIR DISTRICT.

CONSTRUCTION OF GOVERNMENT COLLEGE OF NURSING AT YADGIR, YADGIR DISTRICT. (GF UPTO PLINTH)

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable ...

Earth work in surface excavation by mechanical means for lowering & leveling the ground for all works other than foundation in all kinds of soils & upto depth not exceeding 300mm as per drawing and te...

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

Loading and Unloading of Stone Boulder/Stone aggregates/Sand/ Kankar/Moorum. (Tipper 5.5 m3) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-ch...

Providing and injecting chemical emulsion for Pre-constructional Anti-Termite Treatment, creating continuous chemical barrier under and around the column pits, walls, trenches, basement excavation, to...

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by r...

Filling approved earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and ...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with supe...

Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with supe...

Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with supe...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tyin...

CONSTRUCTION OF GOVERNMENT COLLEGE OF NURSING AT YADGIR, YADGIR DISTRICT. (GF ABOVE PLNTH)

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tyin...

Providing and constructing load bearing wall with Solid Concrete blocks of size 400x200x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2...

Providing and constructing load bearing wall with Solid Concrete blocks of size 400x100x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2...

Providing and fixing flush door shutter made out of solid core block board type, well seasoned , chemicaly treated hard wood battens and internal frame with minimum 45 mm wide wooden frame alround doo...

Providing Salwood frames of doors, windows, clerestory windows, ventilators and other frames, wrought, framed or assembled including making plaster groves (excluding cost of cement concrete and side c...

Fixing of door frame in an existing opening including embedding frame in floor and walls after cutting masonry for holdfasts for embedding holdfast in cement concrete 1:3:6 of 20mm and down size grani...

Providing and fixing Stainless Steel Fixtures conforming to 304

graded steel as per direction of engineer in charge.SS Handles 300mm ---- etc., complete as per specification with all lead and lift and...

Providing and fixing Stainless Steel Fixtures conforming to 304

graded steel as per direction of engineer in charge.SS Aldrop 16mm dia, 300mm ---- etc., complete as per specification with all lead and...

Providing and fixing Stainless Steel Fixtures conforming to 304 graded steel as per direction of engineer in charge.SS Tower Bolts 200x10mm ---- etc., complete as per specification with all lead and l...

Providing and fixing Stainless Steel Fixtures conforming to 304 graded steel as per direction of engineer in charge.SS hinges 100 mm ---- etc., complete as per specification with all lead and lift and...

Providing and fixing Stainless Steel Fixtures conforming to 304 graded steel as per direction of engineer in charge.SS Door stopper 75mm ---- etc., complete as per specification with all lead and lift...

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. ---- etc., complete as per s...

Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. Fastener with threaded dia 12 ...

Supplying and fixing new teak wood beads wherever necessary including cost of materials, labour, complete as per specifications. ---- etc., complete as per specification with all lead and lift and as ...

Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) including preparing the surface after thorougly cleaning oil, grease, di...

Painting wood work with Deluxe Multi Surface Paint of required shade. Two coat applied @ 0.90L/10 Sqm over an under coat of primer applied

@0.75 L/10 Sqm of approved brand and manufacture to give an...

Providing & fixing of 3-track x 2-panel sliding windows made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastome...

Providing & fixing of louvered ventilator made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastomer) and lead fr...

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to stee...

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works including preparing the surface after thorougly cleaning ...

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and for...

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspensi...

Providing and fixing factory made Green certified, Anti Termite, UV resistant, high water absorbant single extruded WPC (Wood PolymerComposite) solid plain flush door shutter of required size comprisi...

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width u...

Providing 12 mm cement plaster with cement mortar 1:6 (1 cement: 6 fine sand) including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost o...

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per sp...

Providing 15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand) including rounding off corners wherever required smooth rendering, providing and remov...

Providing 20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) to brick/stone masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, includi...

Forming groove of uniform size in the top layer of plaster as per approved pattern including repair to the edges of panels and finishing the groove complete as per specific...

Providing and fixing suitable Plaster mesh 150mm wide manufactured out of hot dipped galvanised iron of nominal thickness 0.35mm with a zinc coating of 120g/m2 width, along route of walls chipped for ...

Providing and laying Vitrified tiles with thickness 9-10 mm in different sizes with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, over 12 mm...

Providing and laying flooring and steps fine machine polished granite stone slabs 20 mm thick on cement mortar bed 1:6, 20 mm thick, and joints fin- ished with cement mortar 1:3 over existing cement c...

Providing and fixing 18 mm thick gang saw cut granite of any color and shade, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and ...

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitt...

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops an...

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 g/L and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of r...

Finishing walls with textured exterior paint of required shade :New work (Two coats applied @ 3.28 L/10 Sqm ) over and including priming coat of exterior primer applied @ 2.20kg/10 Sqm to give an e...

Providing and laying Black Lapotra Granite stone flooring in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18mm thick stone slab over 20 mm...

Providing 15 mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement: 4 fine sand) including rounding off corners wherever required smooth rendering, providing and removi...

Providing and supplying crystalline integral concrete waterproofing admixture that waterproofs concrete by forming crystals deep in the pores, capillaries and microcracks of the c...

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thick- ness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades,...

Providing skirting, dadooing, rises of steps with colour glazed tiles 6mm thick on 10mm thick cement plaster 1:3 and jointed with white cement slurry over existing rough plaster surface using glazed t...

Providing and laying cinder concrete in cement 1:15 ( 1 cement : 15 cinder of 12.5mm nominal gauge) on terraced roof or sunken slabs, laid to slope compacting, including cost of materials, labour, cur...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS ...

Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 1:6 (1 cement : 6 coarse sand) ---- etc., complete as per specification with all lead and lift and as per directi...

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based co...

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, w...

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet

(zinc coating not less than 120 gm/Sqm ) of size 20 ...

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- ...

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligni...

Providing and fixing of expansion joint system related with wall joint (internal/external) location as per drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base m...

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extrude...

CONSTRUCTION OF GOVERNMENT COLLEGE OF NURSING AT YADGIR, YADGIR DISTRICT. (FIRST FLOOR)

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tyin...

Providing and constructing load bearing wall with Solid Concrete blocks of size 400x200x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2...

Providing and constructing load bearing wall with Solid Concrete blocks of size 400x100x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2...

Providing and fixing flush door shutter made out of solid core block board type, well seasoned , chemicaly treated hard wood battens and internal frame with minimum 45 mm wide wooden frame alround doo...

Providing Salwood frames of doors, windows, clerestory windows, ventilators and other frames, wrought, framed or assembled including making plaster groves (excluding cost of cement concrete and side c...

Fixing of door frame in an existing opening including embedding frame in floor and walls after cutting masonry for holdfasts for embedding holdfast in cement concrete 1:3:6 of 20mm and down size grani...

Providing and fixing Stainless Steel Fixtures conforming to 304

graded steel as per direction of engineer in charge.SS Handles 300mm ---- etc., complete as per specification with all lead and lift and...

Providing and fixing Stainless Steel Fixtures conforming to 304

graded steel as per direction of engineer in charge.SS Aldrop 16mm dia, 300mm ---- etc., complete as per specification with all lead and...

Providing and fixing Stainless Steel Fixtures conforming to 304 graded steel as per direction of engineer in charge.SS Tower Bolts 200x10mm ---- etc., complete as per specification with all lead and l...

Providing and fixing Stainless Steel Fixtures conforming to 304 graded steel as per direction of engineer in charge.SS hinges 100 mm ---- etc., complete as per specification with all lead and lift and...

Providing and fixing Stainless Steel Fixtures conforming to 304 graded steel as per direction of engineer in charge.SS Door stopper 75mm ---- etc., complete as per specification with all lead and lift...

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. ---- etc., complete as per s...

Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. Fastener with threaded dia 12 ...

Supplying and fixing new teak wood beads wherever necessary including cost of materials, labour, complete as per specifications. ---- etc., complete as per specification with all lead and lift and as ...

Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) including preparing the surface after thorougly cleaning oil, grease, di...

Painting wood work with Deluxe Multi Surface Paint of required shade. Two coat applied @ 0.90L/10 Sqm over an under coat of primer applied

@0.75 L/10 Sqm of approved brand and manufacture to give an...

Providing & fixing of louvered ventilator made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastomer) and lead fr...

Providing & fixing of 3-track x 2-panel sliding windows made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastome...

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to stee...

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works including preparing the surface after thorougly cleaning ...

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and for...

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspensi...

Providing and fixing factory made Green certified, Anti Termite, UV resistant, high water absorbant single extruded WPC (Wood PolymerComposite) solid plain flush door shutter of required size comprisi...

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width u...

Providing 12 mm cement plaster with cement mortar 1:6 (1 cement: 6 fine sand) including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost o...

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per sp...

Providing 15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand) including rounding off corners wherever required smooth rendering, providing and remov...

Providing 20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) to brick/stone masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, includi...

Forming groove of uniform size in the top layer of plaster as per approved pattern including repair to the edges of panels and finishing the groove complete as per specific...

Providing and fixing suitable Plaster mesh 150mm wide manufactured out of hot dipped galvanised iron of nominal thickness 0.35mm with a zinc coating of 120g/m2 width, along route of walls chipped for ...

Providing and laying Vitrified tiles with thickness 9-10 mm in different sizes with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, over 12 mm...

Providing and laying flooring and steps fine machine polished granite stone slabs 20 mm thick on cement mortar bed 1:6, 20 mm thick, and joints fin- ished with cement mortar 1:3 over existing cement c...

Providing and fixing 18 mm thick gang saw cut granite of any color and shade, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and ...

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitti...

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops an...

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 g/L and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of r...

Finishing walls with textured exterior paint of required shade :New work (Two coats applied @ 3.28 L/10 Sqm ) over and including priming coat of exterior primer applied @ 2.20kg/10 Sqm to give an e...

Providing 15 mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement: 4 fine sand) including rounding off corners wherever required smooth rendering, providing and removi...

Providing and supplying crystalline integral concrete waterproofing admixture that waterproofs concrete by forming crystals deep in the pores, capillaries and microcracks of the c...

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thick- ness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades,...

Providing skirting, dadooing, rises of steps with colour glazed tiles 6mm thick on 10mm thick cement plaster 1:3 and jointed with white cement slurry over existing rough plaster surface using glazed t...

Providing and laying cinder concrete in cement 1:15 ( 1 cement : 15 cinder of 12.5mm nominal gauge) on terraced roof or sunken slabs, laid to slope compacting, including cost of materials, labour, cur...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

CONSTRUCTION OF GOVERNMENT COLLEGE OF NURSING AT YADGIR, YADGIR DISTRICT. (TERRACE FLOOR)

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS ...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tyin...

Providing and constructing load bearing wall with Solid Concrete blocks of size 400x200x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2...

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a primi...

Providing & fixing of 3-track x 2-panel sliding windows made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastome...

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to stee...

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per sp...

Providing 12 mm cement plaster with cement mortar 1:6 (1 cement: 6 fine sand) including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost o...

Providing 15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand) including rounding off corners wherever required smooth rendering, providing and remov...

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops an...

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 g/L and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of r...

Finishing walls with textured exterior paint of required shade :New work (Two coats applied @ 3.28 L/10 Sqm ) over and including priming coat of exterior primer applied @ 2.20kg/10 Sqm to give an e...

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works including preparing the surface after thorougly cleaning ...

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and for...

Providing and Applying single component Polyurethane based cold applied seamless waterproofing coating to the RCC surface like Roof & Podium area applied @ 2.4kg/m2 in 3 coats to achieve 1.5mm DFT, in...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS ...

Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approv...

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 g...

CONSTRUCTION OF GOVERNMENT COLLEGE OF NURSING AT YADGIR, YADGIR DISTRICT. (SUMP TANK)

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable ...

Earth work in surface excavation by mechanical means for lowering & leveling the ground for all works other than foundation in all kinds of soils & upto depth not exceeding 300mm as per drawing and te...

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

Earth work excavation for Foundation by mechanical means for all works & depth upto 1.5 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution ...

Earth work excavation for Foundation by mechanical means for all works & depth upto 1.5 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution ...

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by r...

Loading and Unloading of Stone Boulder/Stone aggregates/Sand/ Kankar/Moorum. (Tipper 5.5 m3) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-ch...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tyin...

Providing and constructing load bearing wall with Solid Concrete blocks of size 400x200x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2...

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a primi...

UGT/OHT (inside) waterproofing with Anti-microbial Coating---Providing and Applying two component, water-based food grade epoxy resin coating on inside surface of Potable water tank having anti-algae,...

Providing 20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) to brick/stone masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, includi...

Providing 12 mm cement plaster finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, pr...

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and for...

Providing White washing with lime to give an even shade :New work (three coats) with lime of approved quality, including cost of materials, labour complete as per specifications and as per directions ...

Finishing walls with water proofing cement paint of required shade :New work (Two coats applied @ 4.84 kg/10 Sqm ) to give an even shade after thoroughly brooming the surface to remove all dirt, dust,...

Providing & fixing 455x610 mm cast iron cover with frame weight to be not less 38kgs (weight of cover 23 kgs and weight of frame 15 kgs)and necessary locking arrangements with M.S flats 32x6 mm etc & ...

PProviding & fixing of 2-track x 2-panel sliding windows made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6 PHR with TPE (Thermo Plastic Elast...

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel...

CONSTRUCTION OF GOVERNMENT COLLEGE OF NURSING AT YADGIR, YADGIR DISTRICT. (WATER SUPPLY WORKS)

Providing and fixing Unplasticised Polyvinyl Chloride (uPVC) pipes, for cold water supply including all uPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step uP...

Providing and fixing Unplasticised Polyvinyl Chloride (uPVC) pipes, for cold water supply including all uPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step uP...

Providing and fixing Sewer (SWR) pipes, including all fittings, This includes jointing of pipes & fittings with one step solvent cement,trenching, refilling & testing of joints complete as per directi...

Providing and fixing Sewer (SWR) pipes, including all fittings, This includes jointing of pipes & fittings with one step solvent cement, trenching, refilling & testing of joints complete as per direct...

Providing and fixing PVC (S.W.R) Multi Floor Trap 10.0 cm X 7.5 cm X 5.0 cm X 4.0 cm with all fitting arrangements & all necessary accessories complete FOR GROUND FLOOR TOILETS ---- etc., complete as...

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 FOR GROUND FLOOR TOILETS ---- etc., complete as per specification with all lead...

Providing and fixing C.P. brass long body bib cock of approved quality

conforming to IS standards and weighing not less than 690 g FOR GROUND FLOOR TOILETS ---- etc., complete as per specification wi...

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and c...

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. ...

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with stan...

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the w...

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the w...

Providing and fixing Stainless Steel Grab Bar 600 mm Long with all concealed fitting arrangements & all necessary accesories complete - Class ---- etc., complete as per specification with all lead and...

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 15 mm nominal bore, weighing not less than 32 g ---- etc., complete as per specification with ...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with cla...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with cla...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with cla...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...

Providing and fixing Brass full way valve gate with C.I. wheel of

approved quality (screwed end) : 40 mm nominal bore GROUND FLOOR INTERNAL TOILETS ---- etc., complete as per specification with all ...

Providing and fixing Unplasticised Polyvinyl Chloride (uPVC) pipes, for cold water supply including all uPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step uP...

Providing and fixing Unplasticised Polyvinyl Chloride (uPVC) pipes, for cold water supply including all uPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step uP...

Providing and fixing Sewer (SWR) pipes, including all fittings, This includes jointing of pipes & fittings with one step solvent cement, trenching, refilling & testing of joints complete as per direct...

Providing and fixing Sewer (SWR) pipes, including all fittings, This includes jointing of pipes & fittings with one step solvent cement, trenching, refilling & testing of joints complete as per direct...

Providing and fixing PVC (S.W.R) Multi Floor Trap 10.0 cm X 7.5 cm X 5.0 cm X 4.0 cm with all fitting arrangements & all necessary accessories

complete FOR FIRST FLOOR TOILETS ---- etc., complete as p...

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 FF Toilet (for drinking water point, Wash Basin , Ewc and lab sink) FOR FIRST FL...

Providing and fixing C.P. brass long body bib cock of approved quality

conforming to IS standards and weighing not less than 690 g FOR FIRST FLOOR TOILETS ---- etc., complete as per specification with...

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. ...

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with stan...

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the w...

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the w...

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complet...

Providing and fixing Exposed set for single concealed stop cock with basin spout made of Stainless steel with all concealed fitting rrangements & all necessary accesories complete - Class Economy FOR...

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 15 mm nominal bore, weighing not less than 32 g FOR FIRST FLOOR TOILETS ---- etc., complete a...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with cla...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with cla...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with cla...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...

Providing and fixing Brass full way valve gate with C.I. wheel of

approved quality (screwed end) : 40 mm nominal bore FOR FIRST FLOOR TOILETS ---- etc., complete as per specification with all lead a...

Providing and fixing Sewer (SWR) pipes, including all fittings, This

includes jointing of pipes & fittings with one step solvent cement,

trenching, refilling & testing of joints complete as per direct...

Providing and fixing Sewer (SWR) pipes, including all fittings, This includes jointing of pipes & fittings with one step solvent cement, trenching, refilling & testing of joints complete as per direct...

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal exp...

C.I. grating 180X180 mm FOR TERRACE FLOOR ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Providing and fixing on wall face unplasticised Rigid PVC rain water

pipes of 150mm dia conforming to IS : 13592 Type A, including jointing

with seal ring conforming to IS : 5382, leaving 10 mm gap ...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with cla...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...

Providing and fixing Brass full way valve gate with C.I. wheel of

approved quality (screwed end) : 25 mm nominal bore FOR TERRACE FLOOR ---- etc., complete as per specification with all lead and lif...

Providing and fixing Brass full way valve gate with C.I. wheel of

approved quality (screwed end) : 50 mm nominal bore FOR TERRACE FLOOR ---- etc., complete as per specification with all lead and lif...

Providing and fixing Brass full way valve gate with C.I. wheel of

approved quality (screwed end) : 65 mm nominal bore FOR TERRACE FLOOR ---- etc., complete as per specification with all lead and lif...

Providing and placing on terrace (at all floor levels) polyethylene

water storage tank, IS : 12701 marked, with cover and suitable locking

arrangement and making necessary holes for inlet, outlet an...

Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approv...

Earth work excavation by manual means for drains,canals, waste weir, draft, approach channels, key trenches, foundation of bridges and such simillar works in all kinds of soils , as per drawing and te...

Filling approved earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm

in depth, consolidating each deposited layer by ramming and ...

Providing UPVC FOAM CORE pipes conforming to IS 16098 P-1 2013 with latest amendments ended with integral sockets with ISI mark and conveying to worksite, rolling and lowering into trenches, laying tr...

Providing UPVC FOAM CORE pipes conforming to IS 16098 P-1 2013 with latest amendments ended with integral sockets with ISI mark and conveying to worksite, rolling and lowering into trenches, laying tr...

Providing UPVC FOAM CORE pipes conforming to IS 16098 P-1 2013 with latest amendments ended with integral sockets with ISI mark and conveying to worksite, rolling and lowering into trenches, laying tr...

Providing UNPLASTICISED PVC pipes conforming to IS 16098:2013

with latest amendments ended with integral sockets with ISI mark and conveying to worksite, rolling and lowering into trenches, laying tr...

Constructing brick masonry chamber of internal dimension 600x600mm

and depth of 600mm (inner dimensions) with modular bricks of CD 75

in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plast...

Constructing brick masonry chamber of internal dimension 450x450mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plaster...

Providing and fixing square-mouth S.W. gully trap class SP-1 complete

with C.I. grating brick masonry chamber 150 x 100 mm size P type With Non Modular common burnt clay bricks of designation 3.5 & wi...

Constructing brick masonry chamber of internal dimension 600x600mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plaster...

Providing and fixing DI/CI puddle flanges conforming to IS 7181-1986

with latest ammendments., in position for RCC walls including hoisting and conveying them to work spot with all lead and lifts etc...

Providing and fixing DI/CI puddle flanges conforming to IS 7181-1986

with latest ammendments., in position for RCC walls including hoisting and conveying them to work spot with all lead and lifts etc...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...

Providing and fixing Brass full way valve gate with C.I. wheel of

approved quality (screwed end) :50 mm nominal bore EXTERNAL WATER SUPPLY ---- etc., complete as per specification with all lead and ...

RCC pipe NP3 250 mm dia & 2 M long (PRM ROAD CROSSING) EXTERNAL WATER SUPPLY ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work...

Supply and delivery of Centrifugal pumpset at site brand new best make and with discharge duty confirming to ISI standards and its latest amendments.

5 HP, size 50x40 Head 46M, Discharge 174 LPM (UG ...

Labour charges for Erection, Electrification and commissioning of Pump sets, including aligning and balancing of all items including supply and erection of two pair of supporting clamps, bore well cap...

Supply and delivery at site brand new best make Foot valve suitable for centrifugal pump upto 10HP confirming with ISI mark and its latest amendments. ---- etc., complete as per specification with all...

Earth work excavation by manual means for drains,canals, waste weir, draft, approach channels, key trenches, foundation of bridges and such simillar works in all kinds of soils , as per drawi...

Earth work excavation by manual means for drains,canals, waste weir, draft, approach channels, key trenches, foundation of bridges and such simillar works in all kinds of soils , as per drawi...

Loading and Unloading of Stone Boulder/Stone aggregates/ Sand/Kankar/Moorum. (Disposal of 10Km) ---- etc., complete as per specification with all lead and lift and as per directions of the Engin...

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos lon...

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-cha...

Supplying, filling, spreading &leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all comple...

Supplying, filling, spreading &leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engi...

Gravel packing in tube well construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per di...

Providing and laying 100mm thick pre-cast cover slabs over Rain water harvesting pit of width not exceeding 1000 mm using M20 concrete reinforced with TMT bars Fe 500 @ 6kg/m2, slabs jointed in CM 1:3...

CONSTRUCTION OF GOVERNMENT COLLEGE OF NURSING AT YADGIR, YADGIR DISTRICT. (INTERNAL ELECTRICAL WORKS)

Open Conduit System.Supply Heavy gauge PVC conduit pipe --- dia -- mm thich confirming to IS 2509 with suitable size bends, junction boxes, adhesive paste etc., and fixing using inverted wood plugs in...

Open Conduit System.Supply Heavy gauge PVC conduit pipe --- dia -- mm thich confirming to IS 2509 with suitable size bends, junction boxes, adhesive paste etc., and fixing using inverted wood plugs in...

Open Conduit System.Supply Heavy gauge PVC conduit pipe --- dia -- mm thich confirming to IS 2509 with suitable size bends, junction boxes, adhesive paste etc., and fixing using inverted wood plugs in...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab.The cond...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab.The cond...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab.The cond...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., by grove cutting in the wall surface and fix...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., by grove cutting in the wall surface and fix...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., by grove cutting in the wall surface and fix...

Supplying and fixing sheet Metal box made out of 18SWG sheet metal with necessary holes for cable/lconduit entry as required with one coat of primer of approved make etc. 200x200x65 mm ---- etc., comp...

Supplying and fixing PVC/Metal conduit Deep Junction box 19/20mm deep Junction box ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of th...

Supplying and fixing PVC/Metal conduit Deep Junction box 25mm deep Junction box ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the w...

Supplying and fixing PVC/Metal conduit Deep Junction box 32mm deep Junction box ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the w...

Extra for Groove cutting in brick wall/CC floor to the suitable depth for concealing of Conduit/GI pipe and plastering, finishing upto wall surface complete. upto 50 mm conduit in brick wall ---- etc....

Extra for Groove cutting in brick wall/CC floor to the suitable depth for concealing of Conduit/GI pipe and plastering, finishing upto wall surface complete. upto 50 mm conduit CC floor ---- etc., com...

Supplying and fixing PVC casing and capping on the wall or ceiling using necessary materials like bends,junctionx box,elbows,screws at an interval of 300mm etc as required. 25mm ---- etc., complete as...

Supplying and fixing PVC casing and capping on the wall or ceiling using necessary materials like bends,junctionx box,elbows,screws at an interval of 300mm etc as required. 32mm ---- etc., complete as...

Supplying and fixing PVC casing and capping on the wall or ceiling using necessary materials like bends,junctionx box,elbows,screws at an interval of 300mm etc as required. 38mm ---- etc., complete as...

Supplying and fixing PVC casing and capping on the wall or ceiling using necessary materials like bends,junctionx box,elbows,screws at an interval of 300mm etc as required. 50mm ---- etc., complete as...

Supplying PVC/GI Flexible conduit pipe -- mm dia fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using N...

Supplying PVC/GI Flexible conduit pipe -- mm dia fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using N...

Supplying PVC/GI Flexible conduit pipe -- mm dia fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using N...

Supplying and fixing S hook made out of 14mm dia MS Rod ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying and fixing of Metal Fan box with Round Hook. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wi...

Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wi...

Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wi...

Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wi...

Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wi...

Wiring for Lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concaled system of wiring with speicified IS...

Wiring for Lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concaled system of wiring with speicified IS...

Wiring for Lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concaled system of wiring with speicified IS...

Wiring for Lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concaled system of wiring with speicified IS...

Wiring for Lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concaled system of wiring with speicified IS...

Wiring for Lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concaled system of wiring with speicified IS...

Supplying and drawing flexible multicore cable manufactured with electrolytic grade flexible copper with low conductor conforming to IS 8130-1984 and (Virgin) PVC Insulation sheathed suitable for work...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 8...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 1...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 3...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 4...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 6...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 8...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 1...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 1...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 1...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required Nos of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required Nos of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required Nos of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required Nos of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required Nos of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required Nos of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required Nos of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6Amps one way Switch ---- etc., complete as per specification with all lead ...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6Amps Two way Switch ---- etc., complete as per specification with all lead ...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6Amps 3way socket ---- etc., complete as per specification with all lead and...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. Stepped Fan Regulator Two Module. ---- etc., complete as per specification w...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 16Amps one way switch ---- etc., complete as per specification with all lead...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6A Bell Push ---- etc., complete as per specification with all lead and lift...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 32Amps DP switch ---- etc., complete as per specification with all lead and ...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6/16Amps universal socket ---- etc., complete as per specification with all ...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. TV ---- etc., complete as per specification with all lead and lift and as pe...

Supplying and fixing 32A security and energy saving DP switch with key tag suitable to operate on 230 V, 50Hz AC supply & completely wired on existing box. ---- etc., complete as per specification wit...

Supplying 4mm thick plastic sheet with necessary nitches for fixing switches, regulators etc, and fixing on existing wooden or metal box using N.F. screws. ---- etc., complete as per specification wit...

Supplying and fixing hylum plastic sheet 3mm thick with necessary nitches for fixing switches, regulators etc., and fixing on existing wood or metal box using N. F. screws. ---- etc., complete as per ...

Supplying 50mm wooden plug, tapered from 50x50mm to 25x25mm and fixing by using binding wire before concreting a roof slab. ---- etc., complete as per specification with all lead and lift and as per d...

Supplying ......way plastic gang box and fixing using necessary wooden/ rawl/phill plugs and screws. 6 to 10 Way Gang Box ---- etc., complete as per specification with all lead and lift and as per dir...

Supplying and fixing of metal clad industrial plugs and sockets 2 Pole + earth 250V PLUG 2 Pole + earth 2pole+earth 250V PLUG ---- etc., complete as per specification with all lead and lift and as per...

Supplying and fixing of metal clad industrial plugs and sockets 2 Pole + earth 250V PLUG 3 Pole + earth 440V PLUG .32A ---- etc., complete as per specification with all lead and lift and as per direct...

Supplying and fixing of metal clad industrial plugs and sockets 2 Pole + earth 250V PLUG 2pole+earth 250V SOCKET.32A ---- etc., complete as per specification with all lead and lift and as per directi...

Supplying and fixing of metal clad industrial plugs and sockets 2 Pole + earth 250V PLUG 3pole+earth 440V SOCKET.32A ---- etc., complete as per specification with all lead and lift and as per directio...

Supplying And fixing/replacing of 6/16/32A electrical accessories on existing switch board. 6A Bakelite Ceiling Rose. ---- etc., complete as per specification with all lead and lift and as per directi...

Supplying And fixing/replacing of 6/16/32A electrical accessories on existing switch board. 6A Pendant Holder ---- etc., complete as per specification with all lead and lift and as per directions of t...

Supplying And fixing/replacing of 6/16/32A electrical accessories on existing switch board. 6A Batten Holder ---- etc., complete as per specification with all lead and lift and as per directions of th...

Supplying and fixing of Metal Socket set of 2pole and earth plugs and socket for incorporating SP and TP MCB (Without MCB).The entire plug and socket shall be mounted in a thermoplastic I powder coa...

Supplying and fixing of Metal Socket set of 2pole and earth plugs and socket for incorporating SP and TP MCB (Without MCB).The entire plug and socket shall be mounted in a thermoplastic I powder coa...

Supplying and fixing of minature circuit breakers on exisitng MCB distrubution boards using necessary fixing materials and C Type curve, indicator ON/OFF energy cross-3 with short circuit breaking cap...

Supplying and fixing of minature circuit breakers on exisitng MCB distrubution boards using necessary fixing materials and C Type curve, indicator ON/OFF energy cross-3 with short circuit breaking cap...

Supplying and fixing of minature circuit breakers on exisitng MCB distrubution boards using necessary fixing materials and C Type curve, indicator ON/OFF energy cross-3 with short circuit breaking cap...

Supplying and fixing of minature circuit breakers on exisitng MCB distrubution boards using necessary fixing materials and C Type curve, indicator ON/OFF energy cross-3 with short circuit breaking cap...

Supplying and fixing regular MCB distrubution boards on wall/wood board/ flush mounting ….....with poweder coated painting made out of 14SWG MS enclosure. 16 way SP&N ---- etc., complete as per spec...

Supplying and fixing regular MCB distrubution boards on wall/wood board/ flush mounting ….....with poweder coated painting made out of 14SWG MS enclosure. III - Double Door. 4 Way TP & N ---- etc., ...

Supplying and fixing regular MCB distrubution boards on wall/wood board/ flush mounting ….....with poweder coated painting made out of 14SWG MS enclosure. III - Double Door. 6 Way TP & N ---- etc., ...

Supplying,fixing and wiring residual current circuit breaker (RCCB) 240v/450v upto 300mA sensitivity on exisitng wood panel board. 16A-25A 2 pole ---- etc., complete as per specification with all lead...

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975

Cable trench excavation, 1000x0.6x1=600, Ordinary soil (Extracted from Vol-1, PWD SR Sl Nos 1.17.1) ---- etc., complete as per specification with all lead and lift and as per directions of the Engine...

Artificial/Manufacture Sand (Extracted from Vol-1, PWD SR Sl Nos 62) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Refilling and consolidation (Extracted from Vol-1, PWD SR Sl Nos 1.10) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Spreading Sand and forming with Sand round the cable ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Laying of cable in Existing Trench/GI pipe/Stone Ware/RCC Hume pipe using Wooden/Aluminum Rollers as directed by the departmental staff 2.5 sqmm to 25 sqmm ---- etc., complete as per specification wit...

Laying of cable in Existing Trench/GI pipe/Stone Ware/RCC Hume pipe using Wooden/Aluminum Rollers as directed by the departmental staff 35 sqmm to 95 sqmm ---- etc., complete as per specification with...

Laying of cable in Existing Trench/GI pipe/Stone Ware/RCC Hume pipe using Wooden/Aluminum Rollers as directed by the departmental staff 120 to 240 Sqmm ---- etc., complete as per specification with al...

Supplying and fiixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only) 25mm dia ---- etc., complete as per specification with all lead and lift and as per directions of th...

Supplying and fiixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only) 32mm dia ---- etc., complete as per specification with all lead and lift and as per directions of th...

Supplying and fiixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only) 40 mm dia ---- etc., complete as per specification with all lead and lift and as per directions of t...

Supplying and fiixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only) 45mm dia ---- etc., complete as per specification with all lead and lift and as per directions of th...

Supplying and fiixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only) 50mm dia ---- etc., complete as per specification with all lead and lift and as per directions of th...

Supplying and fiixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only) 63mm dia ---- etc., complete as per specification with all lead and lift and as per directions of th...

Supplying and fiixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only) 75mm dia ---- etc., complete as per specification with all lead and lift and as per directions of th...

GI Pipe, 50 mm Dia for drain crossing, cable raising etc., (Extracted from Vol-5, BWSSB SR Item Nos 183) ---- etc., complete as per specification with all lead and lift and as per directions of the E...

GI Pipe, 65 mm Dia for drain crossing, cable raising etc., (Extracted from Vol-5, BWSSB SR Item Nos 184) ---- etc., complete as per specification with all lead and lift and as per directions of the E...

Labour charges for laying and jointing GI pipes with earth work including fixing collars, elbows, tees, bends, gland cocks and other fittings with cuts and threads, white lead paints wherever necessar...

Labour charges for laying and jointing GI pipes with earth work including fixing collars, elbows, tees, bends, gland cocks and other fittings with cuts and threads, white lead paints wherever necessar...

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes. 10 sqmm ---- etc., complete as per specification with all lead and lift and as per directions of...

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes. 16 sqmm ---- etc., complete as per specification with all lead and lift and as per directions of...

25 Sqmm Copper Terminal, Apprx Wt: 11 Gm ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

50 Sqmm Copper Terminal, Apprx Wt: 26 Gm ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

70 Sqmm Copper Terminal, Apprx Wt: 38 Gm ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

185 Sqmm Copper Terminal, Apprx Wt: 158 Gm ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying and fixing 2mm thick perforated cable tray with powder coated paint on existing MS angle support using necessary Gl bolts/nuts and washer or welding as required 150x50mm ---- etc., comple...

Supplying and fixing 2mm thick perforated cable tray with powder coated paint on existing MS angle support using necessary Gl bolts/nuts and washer or welding as required 300x50mm ---- etc., comple...

Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipment's on the meter board using 40 mm dia 2.90 mm thick GI pipe 2.5m long buried in a pit . The pit shoul...

Supplying fixing and wiring earth electrode for grounding of lifts, transformers, DG sets etc. using 40mm dia 2.9mm thick 2.5 Rmtr long GI pipe with GI funnel with mesh and suitable size reducer fixe...

8 SWG-Cu Wire ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying and running of GI/Copper strips for grounding connections, using necessary fixing materials as required. 25x3mm GI strip ---- etc., complete as per specification with all lead and lift and a...

Supplying and running of GI/Copper strips for grounding connections, using necessary fixing materials as required.25x3mm Copper strip ---- etc., complete as per specification with all lead and lift an...

Supplying and running of GI/Copper strips for grounding connections, using necessary fixing materials as required. 600x600x3mm Copper plate ---- etc., complete as per specification with all lead and l...

Supplying & fixing - flexible LED Strip Light ..... W Power consumption in 5 ms length CCT6500 degree K, CRI 70%. efficacy 80 lumen per W, life 25000 burning hours and Compliance to IS 10322/IEC 60598...

Supplying of ......feet - PVC Batten with integrated LED tube .....W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI 80. Power Input: 220-240V @ 50/60Hz &...

Supplying of ......feet - PVC Batten with integrated LED tube .....W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI 80. Power Input: 220-240V @ 50/60Hz &...

Supplying of ......feet - PVC Batten with integrated LED tube .....W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI 80. Power Input: 220-240V @ 50/60Hz &...

Supply of round/square recess/surface mounted rolling type LED Down light with .......W GU 10 LED Lamp Rib Fabricated from Die cast aluminium with white powder coated prewired to mains connector & has...

Supply of round/square recess/surface mounted rolling type LED Down light with .......W GU 10 LED Lamp Rib Fabricated from Die cast aluminium with white powder coated prewired to mains connector & has...

Supply of round/square recess/surface mounted rolling type LED Down light with .......W GU 10 LED Lamp Rib Fabricated from Die cast aluminium with white powder coated prewired to mains connector & has...

Supply of round/square recess/surface mounted rolling type LED Down light with .......W GU 10 LED Lamp Rib Fabricated from Die cast aluminium with white powder coated prewired to mains connector & has...

Supplying & fixing of retrofit type - LED bulb.......W with OPAL acrylic diffuser comprising of LED source with CCT 6500 degree K, CRI 70%. efficacy 80 lumen per watt, life 25000 burning hours and Com...

Supplying & fixing of retrofit type - LED bulb.......W with OPAL acrylic diffuser comprising of LED source with CCT 6500 degree K, CRI 70%. efficacy 80 lumen per watt, life 25000 burning hours and Com...

Supplying exhaust fan of 1440 RPM of 300mm (12") size with bracket blades complete for light duty suitable to operate on 230V 50Hz, AC Supply. ---- etc., complete as per specification with all lead an...

Supplying of Ceiling Fan with Capacitor rating As per guideline of BEE 5 star rating and IS:374/79 and also comply with IS: 1709/1984 with latest amendment, Rated voltage 220 V/50 Hz, Rated power inpu...

Supplying of Ceiling Fan with Capacitor rating As per guideline of BEE 5 star rating and IS:374/79 and also comply with IS: 1709/1984 with latest amendment, Rated voltage 220 V/50 Hz, Rated power inpu...

Supplying wall mounting fan suitable to operate at singlephase 230v A.C. supply. 300mm Sweep ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-ch...

Fixing all types and all capacities of fluorescent / false ceiling / spot light / CFL / LED fittings indoor on the wall / ceiling / rafters / girders using 23/0.0076” twin twisted PVC insulated wire...

Fixing a ceiling / Wall mounting fan of all capacities and all types to the existing 'S' hook with fan regulator to the existing board together with supplying and fixing 5 amps. ceiling rose, necessar...

Fixing one exhaust fan after making a suitable nitch in the wall and finishing with cement mortar and colouring to match the existing wall or brackets, with bolts and nuts and a 5 amps, ceiling rose w...

Supplying and fixing one of 230 volts Ding dong bell and a flush type bell push with gang box fixed on necessary wooden or rawl plugs using NF screws with Remote. ---- etc., complete as per specificat...

Fabricating supplying and mounting MS box made out ...SWG suitable for floor I wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover,...

Supplying .........amps rated 3phase with neutral bus bar using required capacity electrolytic aluminum strips covered with heat shrinkable coloured PVC sleeve, mounted on phenoliciFRP/DMC i...

Supplying and fixing angle iron frame work iabricated out of M.S. angle iron.. and M.S. flat ... with bolts, washers etc.,and painted with 2 coats of red oxide and then two coats of approved pai...

Supplying and fixing angle iron frame work iabricated out of M.S. angle iron.. and M.S. flat ... with bolts, washers etc.,and painted with 2 coats of red oxide and then two coats of approved pai...

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of O...

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle...

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle...

Suppiying and fixing of Shunt trip suitable for MCCB.CBCT ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying, fixing and wiring earth leakage relay with core balanced current transformer suitable for single phase 50 Hz AC with latest microcontroller based, digital readout of percentage le...

Supplying of multi function digital meter with three line back light LCD type display for voltage, Current, frequency, Power, power factor, KVA, KWH,KVAR suitable for 3 phase, 4 wire LT netwo...

Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 220v A.C. 50 Hz 12/24v D.C ---- etc., complete as per specification with all lead and lift and as per dir...

Supplying, fixing and wiring 50/5 to 400/5A 5VA burden Current Transformer Class 0.5 accuracy with Tape Wound. ---- etc., complete as per specification with all lead and lift and as per directions of ...

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short ci...

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short ci...

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short ci...

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short ci...

Supplying of on load change over switches 4 poles, AC- 23A Duty, 415V, 50Hz, AC Supply. With all accessories. (SM Enclosure Sheet Metal Execution) 200 A ---- etc., complete as per specification with a...

Supply and fixing of Surge Protection devices (SPD)of type-2 at the power source to the sensitive Electronic and Electrical Equipment. Detail Specification is as follow: - In Conformance with standard...

Fabricating,supplying & mounting MS box made out of 14 SWG suitable for floor/wall mounting, fully weather proof with provision for better heat dissipation, providing with hinged front cover, equipped...

Supplying 100A rated 3Phase with Neutral bus bar arrangement using required capacity Electrolytic Al strips covered with Heat shrinkable PVC sleves mounted on Phenolic/FRP/DMC insulators which are mou...

Supplying & fixing angle iron frame work fabricated out of MS angle iron & MS flat with bolts,nuts,washers etc & painted with 2 coats of red oxide Paint& the 2 coats of approved paint 40x40x6mm ---- e...

Supplying & fixing angle iron frame work fabricated out of MS angle iron & MS flat with bolts,nuts,washers etc & painted with 2 coats of red oxide Paint& the 2 coats of approved paint 50x50x6mm ---- e...

Supplying & fixing angle iron frame work fabricated out of MS angle iron & MS flat with bolts,nuts,washers etc & painted with 2 coats of red oxide Paint& the 2 coats of approved paint 50x100x50x6mm C ...

Supplying and fixing 50 - 63 A TPN miniature circuit breaker on the existing MCB distribution board using necessary fixing materials and wiring complete as required. ---- etc., complete as per specif...

Supplying, fixing and wiring Residual current circuit breaker (RCCB) 240/450V upto 300mA sensitivity on existing wood/ panel board. 40Amps 4 pole. ---- etc., complete as per specification with all lea...

Supplying and fixing 6- 32 A DP miniature circuit breaker on the existing MCB distribution board using necessary fixing materials and wiring complete as required. ---- etc., complete as per specificat...

Supplying and fixing 6A SP miniature circuit breaker on the existing MCB distribution board using necessary fixing materials and wiring complete as required. ---- etc., complete as per specification w...

S,F & wiring LED Type Panel Board indicating lamps with reqd color. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying, fixing and wiring 0 to 100 A Direct Reading AC

analog type Ammeter. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the wo...

Supplying, fixing & wiring rotary selector switch suitable for Ammeter. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying, fixing & wiring 0 to 600Volts 96X96mm AC Voltmeter on existing panel/wood board. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-cha...

Supplying, fixing & wiring rotary selector switch suitable for Voltmeter. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

CAPACITOR PANEL-1,(35 KVAR 1NOS) Fabricating supplying and mounting MS box made out ...SWG suitable for floor I wall mounting, fully weather proof with provision for better heat dissipation, ...

Supplying .........amps rated 3phase with neutral bus bar using required capacity electrolytic aluminum strips covered with heat shrinkable coloured PVC sleeve, mounted on phenoliciFRP/DMC i...

Supplying and fixing angle iron frame work iabricated out of M.S. angle iron.. and M.S. flat ... with bolts, washers etc.,and painted with 2 coats of red oxide and then two coats of approved pai...

Supplying and fixing angle iron frame work iabricated out of M.S. angle iron.. and M.S. flat ... with bolts, washers etc.,and painted with 2 coats of red oxide and then two coats of approved pai...

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of O...

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short ci...

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short ci...

Suppiying and fixing of Shunt trip suitable for MCCB.CBCT ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying, fixing and wiring earth leakage relay with core balanced current transformer suitable for single phase 50 Hz AC with latest microcontroller based, digital readout of percentage le...

Supplying of multi function digital meter with three line back light LCD type display for voltage, Current, frequency, Power, power factor, KVA, KWH,KVAR suitable for 3 phase, 4 wire LT netwo...

Supplying, fixing and wiring 50/5 to 400/5A 5VA burden Current Transformer Class 0.5 accuracy with Tape Wound. ---- etc., complete as per specification with all lead and lift and as per directions of ...

Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 220v A.C. 50 Hz 12/24v D.C ---- etc., complete as per specification with all lead and lift and as per dir...

Supplying, fixing and wiring Automatic Power Factor controller fully, static units controlled by 14 stage microprocessor operation, relays LED display, self programming function for power stages and o...

Supplying, fixing and wiring heavy duty low voltage capacitors conforming to IS 2834. 3 phase, 400/440 volts grade, for power factor improvement of rotating machinery ---- etc., complete as per speci...

Supply and fixing of 4pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC-3 Rating and as per IS-13947. 25 A --...

Supplying , & fixing of 6A, 3 Position, Auto-Manual Selector Switch in existing Panel ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge...

Supply and fixing of Surge Protection devices (SPD)of type-2 at the power source to the sensitive Electronic and Electrical Equipment. Detail Specification is as follow: - In Conformance with standard...

UTILITY PANEL Fabricating supplying and mounting MS box made out ...SWG suitable for floor I wall mounting, fully weather proof with provision for better heat dissipation, provided with hinge...

Supplying .........amps rated 3phase with neutral bus bar using required capacity electrolytic aluminum strips covered with heat shrinkable coloured PVC sleeve, mounted on phenoliciFRP/DMC i...

Supplying and fixing angle iron frame work iabricated out of M.S. angle iron.. and M.S. flat ... with bolts, washers etc.,and painted with 2 coats of red oxide and then two coats of approved pai...

Supplying and fixing angle iron frame work iabricated out of M.S. angle iron.. and M.S. flat ... with bolts, washers etc.,and painted with 2 coats of red oxide and then two coats of approved pai...

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of O...

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short ci...

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short ci...

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short ci...

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short ci...

Suppiying and fixing of Shunt trip suitable for MCCB.CBCT ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying, fixing and wiring earth leakage relay with core balanced current transformer suitable for single phase 50 Hz AC with latest microcontroller based, digital readout of percentage le...

Supplying of multi function digital meter with three line back light LCD type display for voltage, Current, frequency, Power, power factor, KVA, KWH,KVAR suitable for 3 phase, 4 wire LT netwo...

Supplying, fixing and wiring 50/5 to 400/5A 5VA burden Current Transformer Class 0.5 accuracy with Tape Wound. ---- etc., complete as per specification with all lead and lift and as per directions of ...

Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 220v A.C. 50 Hz 12/24v D.C ---- etc., complete as per specification with all lead and lift and as per dir...

Supply and fixing of Surge Protection devices (SPD)of type-2 at the power source to the sensitive Electronic and Electrical Equipment. Detail Specification is as follow: - In Conformance with standard...

Supply of LED Streetlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polyc...

Fixing halogen/metal halide / SVL / IL / LED floodlight fitting over existing pole / wall ceiling including clamps, bolts, nuts and wiring using suitable capacity wires. ---- etc., complete as per spe...

Supplying and fixing telescopic M.S. bracket fabricated by using 0.5m length 4” dia telescopic M. S. pipe, with 2” dia 1.5m long M. S. bracket and are welded with suitable angle, using 6mm thick M...

Supplying of Hand gloves. Complete..(KPWD ELE SR 2023-24,P.Nos 93, I.Nos 15.113 ) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the...

Supplying of first aid box. Complete..(KPWD ELE SR 2023-24,P.Nos 93, I.Nos 15.114 ) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of t...

Supplying of SAFETY MASK. Complete.(KPWD ELE SR 2023-24,P.Nos 93, I.Nos 15.115 ) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the ...

Supplying of FIRST AID CHART with lamination.Complete (KPWD ELE SR 2023-24,P.Nos 93, I.Nos 15.116) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer...

Supplying and installation of RUBBER MAT 1Rmtr x1Rmtr -1Omm thick.complete including cost of materials,labour,usage charges of machinery complete as per specifications.(KPWD ELE SR 2023-24,P.Nos 93, I...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. RJ45/ I.O. outlet ---- etc., complete as per specification with all lead and...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. Telephone socket ---- etc., complete as per specification with all lead and ...

Supplying and drawing UTP-CAT 6E LAN cable (85/11.1) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying & Fixing of I/O Socket with back box Single I/O ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying & Fixing of switch mounting rack with power manager & Cable manager as per standard specification 9U with 450mm depth ---- etc., complete as per specification with all lead and lift and as...

Supplying fixing of Network Switches. 16 port 10/100/1000 Switch ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying & fixing of ..Rmtr . Cat 6Patch Cable. 1Rmtr ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying & Fixing of Patch panel for Lan Cabling. 16 Port 10/100 patch panel ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the wor...

Supplying and fixing of MDF krone junction box with KRONE Module / Telephone cable termination. 10 Pair ---- etc., complete as per specification with all lead and lift and as per directions of the Eng...

Supplying and fixing of MDF krone junction box with KRONE Module / Telephone cable termination. 20 Pair ---- etc., complete as per specification with all lead and lift and as per directions of the Eng...

Supplying and drawing PVC flexible one pair telephone unarmoured tinned copper cable.2Pair ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-char...

TELEPHONES Analog push button telephone with Caller ID, flash and radial ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supply, Installation, Testing and Commissioning of 6-core OFC - Armoured outdoor cable (SM) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-c...

Supplying heavy gauge PVC Consealed conduit pipe …….dia ...... mm thick confirming to IS 2509 with suitable size bends, metal/PVC junction boxes adhesive paste etc., and running before concreting...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., by grove cutting in the wall surface and fix...

Supplying and drawing PVC flexible 20 pair telepone unarmoured tinned copper cable. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of ...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 1...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required Nos of machine screws, bolts nuts etc., complete on the existing m...

IP DOME CAMERAS-Supplying, installation, testing and commissioning of 5mp Dome Camera:3.4/4mm fixed Lens sony, 2560 x 1920 resolution, IMX straight Series chipset with Active On board AI chip, Night ...

IP BULLET CAMERAS-Supplying, installation, testing and commissioning of 5mp BULLET Camera:3.4/4mm fixed Lens sony, 2560 x 1920 resolution,IMX straight Series chipset with Active On board AI chip, Nigh...

Supplying, installation, testing and commissioning of SITC of complete 16 channel 4K embedded network video recorder,up to 12MP(4K) resolution live view,preview,and play back,full POE Support (for up ...

Supply and Installation of 8 TB Survalance Hard Disk The rate shall include all mounting accessories complete as required ---- etc., complete as per specification with all lead and lift and as per dir...

Supply and Installation of 8 Port L2 Managed Poe Switch The rate shall include all mounting accessories complete as required ---- etc., complete as per specification with all lead and lift and as per...

Supply and Installation of 55"LED Monitor The rate shall include all mounting accessories complete as required ---- etc., complete as per specification with all lead and lift and as per directions of ...

Supplying and drawing UTP-CAT 6E LAN cable (85/11.1) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying & Fixing of Power strip ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying of shelf ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying & Fixing of castor wheels to the Shelf (set of 4) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying & Fixing of Fan ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying &fixing of 1Rmtr cat 6 Patch Cable ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying & Fixing of sitch mountng rack with power manager & Cable manager. 9U with 650mm depth ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-i...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab.The cond...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., by grove cutting in the wall surface and fix...

Supplying of .. TR Invertor type split Air conditioners suitable for operation on A/C supply single phase 50 Hz 230 V with hermetically sealed inverter compressor with air cooled condenser, latest R41...

Installation charges for split type air conditioner with allied works for one indoor and one outdoor unit is to be mounted on suitable Angle Iron support upto 3.0 Ton split/cassette type A/C. ---- etc...

Supplying, erecting, testing and commissioning of voltage stabilizer suitable for 170 to 270 v input and load variation from no load to full load, with over load protection, spike suppression, operati...

CONSTRUCTION OF GOVERNMENT COLLEGE OF NURSING AT YADGIR, YADGIR DISTRICT. (ELECTRICAL WORKS FIRST FLOOR)

Open Conduit System.Supply Heavy gauge PVC conduit pipe --- dia -- mm thich confirming to IS 2509 with suitable size bends, junction boxes, adhesive paste etc., and fixing using inverted wood plugs in...

Open Conduit System.Supply Heavy gauge PVC conduit pipe --- dia -- mm thich confirming to IS 2509 with suitable size bends, junction boxes, adhesive paste etc., and fixing using inverted wood plugs in...

Open Conduit System.Supply Heavy gauge PVC conduit pipe --- dia -- mm thich confirming to IS 2509 with suitable size bends, junction boxes, adhesive paste etc., and fixing using inverted wood plugs in...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab.The cond...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab.The cond...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab.The cond...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., by grove cutting in the wall surface and fix...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., by grove cutting in the wall surface and fix...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., by grove cutting in the wall surface and fix...

Supplying and fixing sheet Metal box made out of 18SWG sheet metal with necessary holes for cable/lconduit entry as required with one coat of primer of approved make etc. 200x200x65 mm ---- etc., comp...

Supplying and fixing PVC/Metal conduit Deep Junction box 19/20mm deep Junction box ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of th...

Supplying and fixing PVC/Metal conduit Deep Junction box 25mm deep Junction box ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the w...

Supplying and fixing PVC/Metal conduit Deep Junction box 32mm deep Junction box ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the w...

Extra for Groove cutting in brick wall/CC floor to the suitable depth for concealing of Conduit/GI pipe and plastering, finishing upto wall surface complete. upto 50 mm conduit in brick wall ---- etc....

Extra for Groove cutting in brick wall/CC floor to the suitable depth for concealing of Conduit/GI pipe and plastering, finishing upto wall surface complete. upto 50 mm conduit CC floor ---- etc., com...

Supplying and fixing PVC casing and capping on the wall or ceiling using necessary materials like bends,junctionx Box, elbows, screws at an interval of 300mm etc as required. 25mm ---- etc., complete ...

Supplying and fixing PVC casing and capping on the wall or ceiling using necessary materials like bends,junctionx Box, elbows, screws at an interval of 300mm etc as required. 32mm ---- etc., complete ...

Supplying and fixing PVC casing and capping on the wall or ceiling using necessary materials like bends,junctionx Box, elbows, screws at an interval of 300mm etc as required. 38mm ---- etc., complete ...

Supplying and fixing PVC casing and capping on the wall or ceiling using necessary materials like bends,junctionx Box, elbows, screws at an interval of 300mm etc as required. 50mm ---- etc., complete ...

Supplying PVC/GI Flexible conduit pipe -- mm dia fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using N...

Supplying PVC/GI Flexible conduit pipe -- mm dia fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using N...

Supplying PVC/GI Flexible conduit pipe -- mm dia fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using N...

Supplying and fixing S hook made out of 14mm dia MS Rod ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying and fixing of Metal Fan box with Round Hook. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire...

Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire...

Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire...

Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire...

Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire...

Wiring for Lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concaled system of wiring with speicified IS...

Wiring for Lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concaled system of wiring with speicified IS...

Wiring for Lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concaled system of wiring with speicified IS...

Wiring for Lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concaled system of wiring with speicified IS...

Wiring for Lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concaled system of wiring with speicified IS...

Wiring for Lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concaled system of wiring with speicified IS...

Supplying and drawing flexible multicore cable manufactured with electrolytic grade flexible copper with low conductor conforming to IS 8130-1984 and (Virgin) PVC Insulation sheathed suitable for work...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 8...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 1...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 3...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 4...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 6...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 8...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 1...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 1...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 1...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6Amps one way Switch ---- etc., complete as per specification with all lead ...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6Amps Two way Switch ---- etc., complete as per specification with all lead ...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6Amps 3way socket ---- etc., complete as per specification with all lead and...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. Stepped Fan Regulator Two Module. ---- etc., complete as per specification w...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293.16Amps one way switch ---- etc., complete as per specification with all lead ...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293.6A Bell Push ---- etc., complete as per specification with all lead and lift ...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293.32Amps DP switch ---- etc., complete as per specification with all lead and l...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293.6/16Amps universal socket ---- etc., complete as per specification with all l...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293.TV ---- etc., complete as per specification with all lead and lift and as per...

Supplying and fixing 32A security and energy saving DP switch with key tag suitable to operate on 230 V, 50Hz AC supply & completely wired on existing box. ---- etc., complete as per specification wit...

Supplying 4mm thick plastic sheet with necessary nitches for fixing switches, regulators etc, and fixing on existing wooden or metal box using N.F. screws. ---- etc., complete as per specification wit...

Supplying and fixing hylum plastic sheet 3mm thick with necessary nitches for fixing switches, regulators etc., and fixing on existing wood or metal box using N. F. screws. ---- etc., complete as per ...

Supplying 50mm wooden plug, tapered from 50x50mm to 25x25mm and fixing by using binding wire before concreting a roof slab. ---- etc., complete as per specification with all lead and lift and as per d...

Supplying And fixing/replacing of 6/16/32A electrical accessories on existing switch board. 6A Bakelite Ceiling Rose. ---- etc., complete as per specification with all lead and lift and as per directi...

Supplying And fixing/replacing of 6/16/32A electrical accessories on existing switch board. 6A Pendant Holder ---- etc., complete as per specification with all lead and lift and as per directions of t...

Supplying And fixing/replacing of 6/16/32A electrical accessories on existing switch board. 6A Batten Holder ---- etc., complete as per specification with all lead and lift and as per directions of th...

Supplying and fixing of minature circuit breakers on exisitng MCB distrubution boards using necessary fixing materials and C Type curve, indicator ON/OFF energy cross-3 with short circuit breaking cap...

Supplying and fixing of minature circuit breakers on exisitng MCB distrubution boards using necessary fixing materials and C Type curve, indicator ON/OFF energy cross-3 with short circuit breaking cap...

Supplying and fixing of minature circuit breakers on exisitng MCB distrubution boards using necessary fixing materials and C Type curve, indicator ON/OFF energy cross-3 with short circuit breaking cap...

Supplying and fixing of minature circuit breakers on exisitng MCB distrubution boards using necessary fixing materials and C Type curve, indicator ON/OFF energy cross-3 with short circuit breaking cap...

Supplying and fixing regular MCB distrubution boards on wall/wood board/ flush mounting ….....with poweder coated painting made out of 14SWG MS enclosure. II - Double Door. 16 way SP&N ---- etc., co...

Supplying and fixing regular MCB distrubution boards on wall/wood board/ flush mounting ….....with poweder coated painting made out of 14SWG MS enclosure. II - Double Door. 4 Way TP & N ---- etc., c...

Supplying and fixing regular MCB distrubution boards on wall/wood board/ flush mounting ….....with poweder coated painting made out of 14SWG MS enclosure. II - Double Door. 6 Way TP & N ---- etc., c...

Supplying,fixing and wiring residual current circuit breaker (RCCB) 240v/450v upto 300mA sensitivity on exisitng wood panel board. 16A-25A 2 pole ---- etc., complete as per specification with all lead...

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975

Laying of cable in Existing Trench/GI pipe/Stone Ware/RCC Hume pipe using Wooden/Aluminum Rollers as directed by the departmental staff 2.5 sqmm to 25 sqmm ---- etc., complete as per specification wit...

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes. 10 sqmm ---- etc., complete as per specification with all lead and lift and as per directions of...

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes 16 sqmm ---- etc., complete as per specification with all lead and lift and as per directions of ...

Supplying and fixing 2mm thick perforated cable tray with powder coated paint on existing MS angle support using necessary Gl bolts/nuts and washer or welding as required 150x50mm ---- etc., comple...

Supplying and fixing 2mm thick perforated cable tray with powder coated paint on existing MS angle support using necessary Gl bolts/nuts and washer or welding as required 300x50mm ---- etc., comple...

Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipment's on the meter board using 40 mm dia 2.90 mm thick GI pipe 2.5m long buried in a pit . The pit shoul...

8 SWG-Cu Wire ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying and running of GI/Copper strips for grounding connections, using necessary fixing materials as required. 25x3mm GI strip ---- etc., complete as per specification with all lead and lift and a...

Supplying of ......feet - PVC Batten with integrated LED tube .....W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI 80. Power Input: 220-240V @ 50/60Hz &...

Supplying of ......feet - PVC Batten with integrated LED tube .....W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI 80. Power Input: 220-240V @ 50/60Hz &...

Supplying of ......feet - PVC Batten with integrated LED tube .....W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI 80. Power Input: 220-240V @ 50/60Hz &...

Supply of round/square recess/surface mounted rolling type LED Down light with .......W GU 10 LED Lamp Rib Fabricated from Die cast aluminium with white powder coated prewired to mains connector & has...

Supply of round/square recess/surface mounted rolling type LED Down light with .......W GU 10 LED Lamp Rib Fabricated from Die cast aluminium with white powder coated prewired to mains connector & has...

Supply of round/square recess/surface mounted rolling type LED Down light with .......W GU 10 LED Lamp Rib Fabricated from Die cast aluminium with white powder coated prewired to mains connector & has...

Supply of round/square recess/surface mounted rolling type LED Down light with .......W GU 10 LED Lamp Rib Fabricated from Die cast aluminium with white powder coated prewired to mains connector & has...

Supplying & fixing of retrofit type - LED bulb.......W with OPAL acrylic diffuser comprising of LED source with CCT 6500 degree K, CRI 70%. efficacy 80 lumen per watt, life 25000 burning hours and Com...

Supplying & fixing of retrofit type - LED bulb.......W with OPAL acrylic diffuser comprising of LED source with CCT 6500 degree K, CRI 70%. efficacy 80 lumen per watt, life 25000 burning hours and Com...

Supplying exhaust fan of 1440 RPM of 300mm (12") size with bracket blades complete for light duty suitable to operate on 230V 50Hz, AC Supply. ---- etc., complete as per specification with all lead an...

Supplying of Ceiling Fan with Capacitor rating As per guideline of BEE 5 star rating and IS:374/79 and also comply with IS: 1709/1984 with latest amendment, Rated voltage 220 V/50 Hz, Rated power inpu...

Supplying of Ceiling Fan with Capacitor rating As per guideline of BEE 5 star rating and IS:374/79 and also comply with IS: 1709/1984 with latest amendment, Rated voltage 220 V/50 Hz, Rated power inpu...

Supplying wall mounting fan suitable to operate at singlephase 230v A.C. supply. 300mm Sweep ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-ch...

Fixing all types and all capacities of fluorescent / false ceiling / spot light / CFL / LED fittings indoor on the wall / ceiling / rafters / girders using 23/0.0076” twin twisted PVC insulated wire...

Fixing a ceiling / Wall mounting fan of all capacities and all types to the existing 'S' hook with fan regulator to the existing board together with supplying and fixing 5 amps. ceiling rose, necessar...

Fixing one exhaust fan after making a suitable nitch in the wall and finishing with cement mortar and colouring to match the existing wall or brackets, with bolts and nuts and a 5 amps, ceiling rose w...

Supplying and fixing one of 230 volts Ding dong bell and a flush type bell push with gang box fixed on necessary wooden or rawl plugs using NF screws with Remote. ---- etc., complete as per specificat...

Supplying of Hand gloves. Complete..(KPWD ELE SR 2023-24,P.No.93, I.No.15.113 ) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the w...

Supplying of first aid box. Complete..(KPWD ELE SR 2023-24,P.No.93, I.No.15.114 ) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the...

Supplying of SAFETY MASK. Complete.(KPWD ELE SR 2023-24,P.No.93, I.No.15.115 ) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the wo...

Supplying of FIRST AID CHART with lamination.Complete (KPWD ELE SR 2023-24,P.No.93, I.No.15.116) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-i...

Supplying and installation of RUBBER MAT 1Rmtr x1Rmtr -1Omm thick.complete including cost of materials,labour,usage charges of machinery complete as per specifications.(KPWD ELE SR 2023-24,P.No.93, I....

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. RJ45/ I.O. outlet ---- etc., complete as per specification with all lead and...

Supplying and drawing UTP-CAT 6E LAN cable (85/11.1) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying & Fixing of I/O Socket with back box Single I/O ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying & Fixing of switch mounting rack with power manager & Cable manager as per standard specification 9U with 450mm depth ---- etc., complete as per specification with all lead and lift and as...

Supplying fixing of Network Switches. 16 port 10/100/1000 Switch ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying & fixing of ..Rmtr s. Cat 6Patch Cable. 1Rmtr ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying heavy gauge PVC Consealed conduit pipe …….dia ...... mm thick confirming to IS 2509 with suitable size bends, metal/PVC junction boxes adhesive paste etc., and running before concreting...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., by grove cutting in the wall surface and fix...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 1...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...

IP DOME CAMERAS-Supplying, installation, testing and commissioning of 5mp Dome Camera:3.4/4mm fixed Lens sony, 2560 x 1920 resolution, IMX straight Series chipset with Active On board AI chip, Night ...

IP BULLET CAMERAS-Supplying, installation, testing and commissioning of 5mp BULLET Camera:3.4/4mm fixed Lens sony, 2560 x 1920 resolution,IMX straight Series chipset with Active On board AI chip, Nigh...

Supply and Installation of 8 Port L2 Managed Poe Switch The rate shall include all mounting accessories complete as required ---- etc., complete as per specification with all lead and lift and as per...

Supplying and drawing UTP-CAT 6E LAN cable (85/11.1) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying &fixing of 1Rmtr cat 6 Patch Cable ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying & Fixing of sitch mountng rack with power manager & Cable manager. 9U with 650mm depth ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-i...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab.The cond...

Supplying heavy gauge PVC conduit pipe --- mm dia -- thick confirming to IS 2509 with suitable size bends,metal/PVC junction boxes, adhesive paste etc., by grove cutting in the wall surface and fix...

Supplying of .. TR Invertor type split Air conditioners suitable for operation on A/C supply single phase 50 Hz 230 V with hermetically sealed inverter compressor with air cooled condenser, latest R41...

Installation charges for split type air conditioner with allied works for one indoor and one outdoor unit is to be mounted on suitable Angle Iron support upto 3.0 Ton split/cassette type A/C. ---- etc...

Supplying, erecting, testing and commissioning of voltage stabilizer suitable for 170 to 270 v input and load variation from no load to full load, with over load protection, spike suppression, operati...

Supplying, erecting, testing & commissioning of OFF-LINE UPS system suitable for operation on 230V, 50Hz, A/C supply, with isolation transformer all accessories complete and Excluding batteries and wi...

Supplying, installation, testing & commissioning of 12V DC, AH batteries in poly propylene container for U.P.S. Sealed maintenance free batteries. 80 AH capacity ---- etc., complete as per specificati...

Supplying, erecting, testing & commissioning of ON-LINE UPS system suitable for operation on 230V, 50Hz, A/C supply, with isolation transformer all accessories complete and Excluding batteries and wir...

Supplying, installation, testing & commissioning of 12V DC, AH batteries in poly propylene container for U.P.S. Sealed maintenance free batteries. 120 AH capacity ---- etc., complete as per specificat...

CONSTRUCTION OF GOVERNMENT COLLEGE OF NURSING AT YADGIR, YADGIR DISTRICT. (EXTERNAL ELECTRIFICATION)

Part-A Providing 2 Pole Structrue at the Tapping Point,TC yard.Using RCC Pole(2 NOS) Supply of DP Structure using RCC Pole - 9 Mtr Long, 145 Kg WL (Including Cost of Poles). ---- etc., complete as per...

fixing of DP Structure using RCC Pole - 9 Mtr Long, 145 Kg WL (Including Cost of Poles). ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge...

Supply of 11 kV, 45 KN Polymeric Insulator. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supply of Guy Set Complete with No. 15 Strain Insulator & Concreting materials. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the w...

Fixing of Guy Set Complete with No. 15 Strain Insulator & Concreting materials. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the w...

Supply of Guy Wire & GI Wire as per IS-2141.7/10 SWG Guy Wire(7/3.251 mm Dia), Std Wt: 680 Kg/KM. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-...

Digging of Pit for GUY SET.Ordinary Soil. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

supply of Spiral Earth Electrode. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Providing Spiral Earth Electrode type earthing. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supply of Caution/Danger Board. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

fixing of Caution/Danger Board. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supply of Anti Climbing Device (12 Mtr GI Barbed Wire). ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

fixing of Anti Climbing Device (12 Mtr GI Barbed Wire). ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supply of 11 kV, 400 Amps Double Break GOS(Dwg No. BESCOM/GM/QS&S/22 Dtd 24.11.2018). ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of...

Fixing of GOS including wiring (11 kV Double Break 400 Amps). ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supply of H-Frame for mounting. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Erection of H-Frame.for mounting GOS. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supply of 11 kV, DOLO Cutout Conventional to Erstwhile KEB Specification. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Fixing DOLO Cutout/Horn Gap Fuse including fixing of cross arm and wiring. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supply of Rabbit ACSR Conductor. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Laying of Rabbit ACSR Conductor. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supply of PG Clamps for Rabbit Conductor. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

PART B- Laying of 11 KV 3 Core 95 Sqmm XLPE UG Cable from Tappint point dp to tc yard dp to LBS TO to transformer with excavation of soil Supply of 11 kV, 3 Core, XPLE HTUG Cable with pressure extrud...

Supply of Heat Shrinkable Indoor Type Cable Termination Kit for XLPE Cable.3Cx95sqmm indoor. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-c...

Supply of Heat Shrinkable Outdoor Type Cable Termination Kit for XLPE Cable 3Cx95sqmm outdoor. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in...

Supply of Cable covering tiles 250x125x40mm.. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supply of Artificial/Manufacture Sand (Extracted from Vol-1, PWD SR Sl No. 62) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the wo...

Supply of RCC humepipes 2000mm long 150mm dia. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supply of Collars for RCC hume pipes. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supply of GI Pipe, 100 mm Dia for drain crossing, cable raising etc., (Extracted from Vol-5, BWSSB SR Item No. 177 ---- etc., complete as per specification with all lead and lift and as per direction...

Supply of Route and Joint indicating stones with MS Anchor rod. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Cable trench excavation, 1000x0.6x1=600, Ordinary soil (Extracted from Vol-1, PWD SR Sl No. 1.17.1) ---- etc., complete as per specification with all lead and lift and as per directions of the Enginee...

Refilling and consolidation (Extracted from Vol-1, PWD SR Sl No. 1.10) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Laying of cable in Existing Trench/GI pipe/Stone Ware/RCC Hume pipe using Wooden/Aluminum Rollers as directed by the departmental staff.3x95 to 150 Sqmm. ---- etc., complete as per specification with ...

Retailing the cable trenches with selected availble earth from trench excavation including watering,Consolidation in layers of 15Cm thickness including depositing of the surplus earth with a lead of 2...

Making and Fixing pot head for HT Cable only.Heat shrinkable Type Terminations.3x95 to 3x150 Sqmm. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer...

Covering the cables with tiles. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Spreading and forming with sand alround the cable to a depth of 75mm and width of 500mm . ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charg...

Laying and Jointing the pipes (100-150 mm Dia) including lowering in Position: Fixing Collars etc., Joining with mud mortor complete.RCC Pipe.. ---- etc., complete as per specification with all lead a...

Fixing of Route Joint Indicating Slab.. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

PART C- Providing of LT Metering Cubicle(BESCOM SR 23-24) Providing Electronic Trivector Meters with Associated CT's Metering Box etc., on LT Side of Distribution Transformer Center.supply of LT CT's ...

Fixing of Electronic Trivector Meters with Associated CT's Metering Box etc., on LT Side of Distribution Transformer Center.fixing of LT CT's 0.5 Accuracy Class Ring Type Ratio 400/5 for 250 kVA DTC....

supply of Electronic Trivector Meter 3 Phase, 4 Wire, 0.5 Accuracy Class. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

fixing of Electronic Trivector Meter 3 Phase, 4 Wire, 0.5 Accuracy Class. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

supply of Weather Proof, Verming Proof LT Metering Box with clamping arrangement for mounting on the Transformer structure with necessary terminal strip and CT mounting arrangement for housing the ETV...

fixing of Weather Proof, Verming Proof LT Metering Box with clamping arrangement for mounting on the Transformer structure with necessary terminal strip and CT mounting arrangement for housing the ETV...

Load Break switches with Panel. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Erection Alignment and fixing of Load break switch on the platform. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Earth work excavation for Foundation by mechanical means for all kinds of soil & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, ca...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 1:6 (1 cement : 6 coarse sand).1 no(1.5*1.5*1)-2.48 ---- etc., complete as per specification with all lead and li...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Providing Flush/ Ruled pointing: Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) after raking joints to depth nicely lin- ing, including cost of materials, labour, curing as per...

Providing 12 mm cement plaster finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, prov...

PART D- Erection of 1NO OF 3 phase 11Kv/433 Volts ,100 KVA,BEE-5Star rated Distribution transformer center Distribution Transformer - 3 Phase, 11kV/433V - Stacked CRGO Core with Oil as per IS-1180 (...

Erection of 100 kVA Transformer ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 1:6 (1 cement : 6 coarse sand).Foundation wall -((9+5)*2)*0.60*0.45-7.56 CUM,Basement-((9+5)*2)*0.45*0.45-5.67 CU...

Providing and laying in Cement Concrete for all Basement & surface level works, return walls, retaining walls, sunken floors etc. The granite/trap/ basalt crushed graded coarse aggregates and fine agg...

Providing 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix: 1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corne...

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tyin...

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete....

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direct...

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and for...

Supplying fixing and wiring earth electrode for grounding of lifts, transformers, DG sets etc. using 40mm dia 2.9mm thick 2.5 mtr long GI pipe with GI funnel with mesh and suitable size reducer fixed ...

Supplying and running GI/Copper conductor for grounding and (along with other wires in conduit system of wiring) using necessary suitable size clamps, nails, guttas/spacers etc.,(75/23) 8 SWG-Cu Wire...

Supplying and running of GI/Copper strips for grounding connections, using necessary fixing materials as required. 25x3mm GI strip ---- etc., complete as per specification with all lead and lift and a...

25x3mm Copper strip ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

600x600x3mm Copper plate ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

PART-F 1 NO OF LT Distribution Box as per IS-13947 Part- 1&2.LT Distribution Box for 100 kVA DTC with MCCB's Fabricating supplying and mounting MS box made out ...SWG suitable for floor I wall m...

Supplying .........amps rated 3phase with neutral bus bar using required capacity electrolytic aluminum strips covered with heat shrinkable coloured PVC sleeve, mounted on phenoliciFRP/DMC i...

Supplying and fixing angle iron frame work iabricated out of M.S. angle iron.. and M.S. flat ... with bolts, washers etc.,and painted with 2 coats of red oxide and then two coats of approved pai...

Supplying and fixing angle iron frame work iabricated out of M.S. angle iron.. and M.S. flat ... with bolts, washers etc.,and painted with 2 coats of red oxide and then two coats of approved pai...

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle...

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short ci...

Suppiying and fixing of Shunt trip suitable for MCCB.CBCT ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supplying, fixing and wiring earth leakage relay with core balanced current transformer suitable for single phase 50 Hz AC with latest microcontroller based, digital readout of percentage le...

Supplying of multi function digital meter with three line back light LCD type display for voltage, Current, frequency, Power, power factor, KVA, KWH,KVAR suitable for 3 phase, 4 wire LT netwo...

Supplying, fixing and wiring 50/5 to 400/5A 5VA burden Current Transformer Class 0.5 accuracy with Tape Wound. ---- etc., complete as per specification with all lead and lift and as per directions of ...

Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 220v A.C. 50 Hz 12/24v D.C ---- etc., complete as per specification with all lead and lift and as per dir...

Supply of RCC Hume Pipe, 2000 mm Long, 150 mm Dia ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Laying of RCC Hume Pipe, 2000 mm Long, 150 mm Dia ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supply of Collars for RCC Hume Pipe ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Supply of Route and Joint indicating stones with MS Anchor rod. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Fixing of Route Joint Indicating Slab.. ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-charge of the work.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 500X700 mm internal ...

Extra for depth beyond 45 cm of brick masonry chamber : For 500x700

mm size With common burnt clay (non modular) bricks of class

designation 3.5 ---- etc., complete as per specification with all lead ...

Open Conduit System Supplying heavy gauge PVC conduit pipe …….dia .......mm thick confirming to IS 2509 with suitable size bends, junction boxes, adhesive paste etc., and fixing using inverted woo...

Supplying and drawing Flexible Multicore Cable manufactured with electrolytic grade flexible copper with low conductor confirming to IS 8130-1984 and (Virgin) PVC insulation sheathed suitable for work...

Fabricating, supplying and erecting swaged tubular pole of height …Mtr having three sections, and providing twocoats of red oxide paint and finished with two coats of enamelled paint of approved qua...

Supplying and fixing of 4 pole power contactor with NO/NC contacts on existing wood/panel boaard using necessary bolts,nuts, washers and wiring etc., completee with ac-3 rating and as per IS-13947 40 ...

Supply and Installation / Fixing / Provision of Outdoor type Thermoplastic Modular Panel enclosure with transparent Polycarbonate Lid, shock proof, IP65 (Weather Proof), rust proof, dust proof, water ...

Supplying and fixing Microprocessor Based Astronomical timer Switch with using necessary bolts, nuts and washers. ---- etc., complete as per specification with all lead and lift and as per directions ...

Supply of LED Streetlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation.Lamp compartment comprising of anti glare clear diffuser with Injection moulded polyca...

Supplying and fixing telescopic M.S. bracket fabricated by using 0.5m length 4” dia telescopic M. S. pipe, with 2” dia 1.5m long M. S. bracket and are welded with suitable angle, using 6mm thick M...

Fixing halogen/metal halide / SVL / IL / LED floodlight fitting over existing pole / wall ceiling including clamps, bolts, nuts and wiring using suitable capacity wires. ---- etc., complete as per spe...

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 16 Sqmm,...

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 25 Sqmm,...

Laying of cable in Existing Trench/GI pipe/Stone Ware/RCC Hume pipe using Wooden/Aluminum Rollers as directed by the departmental staff 2.5 sqmm to 25 sqmm ---- etc., complete as per specification wit...

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes. 25 Sqmm Copper Terminal, Apprx Wt: 11 Gm ---- etc., complete as per specification with all lead ...

Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipment's on the meter board using 40 mm dia 2.90 mm thick GI pipe 2.5m long buried in a pit . The pit shoul...

Supplying and running of GI/Copper strips for grounding connections, using necessary fixing materials as required. 25x3mm GI strip ---- etc., complete as per specification with all lead and lift and a...

CONSTRUCTION OF GOVERNMENT COLLEGE OF NURSING AT YADGIR, YADGIR DISTRICT. (FIRE FIGHTING WORKS)

Supplying Installing, testing and commissioning of 19mm dia 40.0m length hose with rubber lining smooth bore, reinforced of natural/synthetic fibres, a rubber cover finishshall besmooth, flutedor fa...

Supply, installation of 4kg Fire Extinguisher Mono Ammonium PhosphatePowder 50, StoredPressure Type, Pressure Gauge, Gross Weight 6.9Kg, emptyweight 2.9Kg, Can Height 440MM, Diameter 140MM, Discharge...

Supply and installation of 2Kg C02 Gas Type Fire Extinugisher Squeeze grip type, used Unused Mechanism, Squeeze Grip,Gross Weight 9.1Kg. empty Weight 7.1Kg. Can Height 595 MM Diameter 108MM,Discharg...

Supply and installationof 4.5Kg C02 Gas Type aluminium body Squeeze grip Fire Extinugisher, TrolleyMounted, Easy Weight Management, Used UnusedMechanism, Squeeze Grip, Gross Weight 11.16Kg.

Providing and Fixing Fire force boardsize of 3'x2 'madeout to Acrylic sheet

of 3mm thick and fixing with Stainless Steel finished studs etc. complete

including cost of materials, labour,usage charge...

Supplying Installing, testing and commissioning of 19mm dia 40.0m

length hose with rubber lining smooth bore, reinforced of natural/synthetic

fibres, a rubber cover finishshall besmooth, flutedor fa...

Supply, installation of 4kg Fire Extinguisher Mono Ammonium PhosphatePowder 50, StoredPressure Type, Pressure Gauge, Gross B Weight 6.9Kg, emptyweight 2.9Kg, Can Height 440MM, Diameter 140MM, Discha...

Supplyandinstallationof2KgC02 Gas Type Fire Extinugisher Squeeze grip type, usedUnusedMechanism, SqueezeGrip,GrossWeight 9.1Kg. emptyWeight 7.1Kg. CanHeight 595MMDiameter 108MM,Discharge Time less ...

Providing and Fixing Fire force boardsize of 3'x2 'madeout to Acrylic sheet

of 3mm thick and fixing with Stainless Steel finished studs etc. complete

including cost of materials, labour,usage charge...

Supply, installation, testingand commissioning electrically driven Terrance

pump of capacity 450.0 Lpm at 35.0m Head bronze impeller pump coupled to

electrical driven moto rwith suitabl eHP withall ...

Supplying, installing, testing & commissioning approved make heavyduty

(Class 'C') GIpipes and fittings confirming to IS1239 PI&II,Malleable

Specialssuchastees, longradiusbends,checknuts,unions, fla...

Supplying ,installing, testing and commissioning of PN16CI butterfly valves

of confirming to IS13039 with necessary nuts & bolts etc .,complete----etc.,

complete as per specificaiton with all lead a...

Supplying installing, testingandcommissioningof PN16CI "NonReturn

Valve"confirmingtoIS13039withnecessaryboltsandnutsetccomplete

includes cost of allmaterials labour chargeswithall lead lift loadinga...

supply and installing testing and commissioning of CI " Y " stainer

confirming toISstandardwithnecessaryboltsandnutscomplete includes

costofallmaterials labourchargeswithall leadlift loadingandunloa...

Supplying Installing, testing and commissioning of Gun metal AIR

RELEASE VALVE SIZE OF 25mm dia in cluding costo fmaterials, labour,

usage charges of machinery complete as per specifications. Comp...

Providing and placing on terrace (at all floor levels) polyethylene

water storage tank, IS : 12701 marked, with cover and suitable locking

arrangement and making necessary holes for inlet, outlet an...

CONSTRUCTION OF GOVERNMENT COLLEGE OF NURSING AT YADGIR, YADGIR DISTRICT. (C.C ROAD)

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable ...

Earth work in surface excavation by mechanical means for lowering & leveling the ground for all works other than foundation in all kinds of soils & upto depth not exceeding 300mm as per drawing and te...

Earth work excavation by manual means for drains, canals, waste weir, draft, approach channels, key trenches, foundation of Buildings & bridges and such simillar works in all kinds of soils, as per dr...

Removal of Unserviceable Soil with Disposal upto a suitable distance as directed by the Engineer incharge of work ---- etc., complete as per specification with all lead and lift and as per directions ...

Making 50 mm x 50 mm furrows, 25mm/ 50mm deep, 45 degrees to the center line of the road and at one metre interval in the existing thin bituminous wearing coarse including sweeping and disposal of exc...

Compacting original ground supporting embankment-Loosening, leveling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of ...

Construction of Embankment by excavating the available approved Gravel/ Murrum deposited at a place or borrow pits during or prior excavation with all lifts and lead, transportation to site, spreading...

Construction of Granular Sub-Base of required grading as per design spreading in uniform layers with motor grader on prepared surface mixing by mix in place method with front end loader at OMC and com...

Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ra...

Construction of M40 Grade un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base in recommended proportions, coarse and fine aggregate conforming to IS 383:2016, maximum...

Cutting transverse contraction joints 3 to 4 mm wide and depth 60mm in concrete slab using concrete cutting machine with diamond studded saw within 4-8 hours of casting of bay / slab etc. complete inc...

Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces. ---- etc., complete as per specification with all lead and lift and as per di...

Painting lines, dashes, arrows etc on roads in two coats on new work with ready mixed road marking paint conforming to IS:164:2015 on bituminous surface, including cleaning the surface of all dirt, du...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

Supplying and fixing M15 grade precast cement concrete Kerb stones for Roadway, Sidewalls and gutters fixed with CM 1:3 fixed and finsihed in line as per direction of Engineer in charge. (The cost of ...

CONSTRUCTION OF GOVERNMENT COLLEGE OF NURSING AT YADGIR, YADGIR DISTRICT. (CONSTRUCTION OF DRAIN)

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

Loading and Unloading of Stone Boulder/Stone aggregates/Sand/ Kankar/Moorum. (Tipper 5.5 m3) ---- etc., complete as per specification with all lead and lift and as per directions of the Engineer-in-ch...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tyin...

CONSTRUCTION OF GOVERNMENT COLLEGE OF NURSING AT YADGIR, YADGIR DISTRICT. (COMPOUND WALL)

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable ...

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

Loading and Unloading of Stone Boulder/Stone aggregates/ Sand/Kankar/Moorum & Cost of Haulage Excluding Loading and Unloading Taking output 5 t load and lead 10 km = 100 t.km (135+12x5x1.35) --...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tyin...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS ...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and constructing load bearing wall with Solid Concrete blocks of size 400x200x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2...

Providing 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix: 1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corne...

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 g/L and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of r...

Providing and fixing Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel et...