801668 IMPROVEMENT TO SNCOS MESS AND AIRMEN MESS AND OTHER

Amount

SCHEDULE 'A' PART - I (B/R Portion) Demolition of Concrete (Unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of concrete(unreinforced) of any description and in any position not otherwise specifically provided as in padding concrete kerbs, chajja filleting staircase treads etc. complete all as specified and as directed.

Demolition of concrete (reinforced) of any description and in any position (reinforcement cut as required to facilitate demolition) as in shelves and like complete all as specified and as directed.

Material and labour for plain cement concrete 1:2:4 type B1 using 20mm graded aggregate as in kerbs, chajja filleting complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and as directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqm on plan and getting out in hard dense soil complete all as specified and as directed.

Material and labour for Cement concrete 1:4:8 type D2 using 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

Material and labour for Pre-cast cement concrete block masonry with solid blocks, of 1:3:6 type C1 using 20mm graded aggregate exceeding 10 cm in width and setting in cement mortar 1:6, complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

Raking out joints/ pointing to squared rubble masonry, coursed or uncoursed, etc (Height of bldg 7.00m) complete all as specified and as directed.

Material and labour for flush pointing in CM 1:4 to squared rubble masonry, coursed or uncoursed all as specified including key groove (Height of bldg 7.00m) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but including backing), removing serviceable tiles if any to store and rubbish off the premises complete all as specified and as directed.

Material and labour for 75mm thick plain Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) as in sub base complete all as specified and as directed.

Material and labour for 75mm thick plain Cement concrete type B1 1:2:4 (20mm graded stone aggregate) as in plinth protection including necessary grooves along the wall and 3m interval normal to wall and filling with mixture of sand and bitumen complete all as specified and directed.

Material and labour for Dubbing out average 10mm thick in CM 1:6 on irregular face of walls complete all as specified and as directed.

Material and labour for 20mm thick rendering in CM 1:6 on stone masonry wall surfaces finished even and fair without using extra cement complete all as specified and as directed.

Material and labour for 10mm thick rendering in CM 1:4 on block masonry wall/concrete surfaces finished even and fair without using extra cement with liquid water proofing compound complete all as specified and as directed. (Note: Liquid Water proofing compound shall be measured and paid separately)

Supply only water proofing liquid ISI marked.

Material and labour for 10mm thick rendering in CM 1:3 on ceiling surfaces finished even and fair without using extra cement complete all as specified and as directed.

Supply and fix 18mm thick factory made single extruded WPC( Wood Polymer Composite) 100% lead free plain white board comprising of virgin polymer of K value 58-60, calcium carbonate and natural fibres (Wood powder/rice husk.wheat husk) and non toxic additives having minimum density of 650Kg/Cum and screw withdrawal strength of 1800N (Face) and 900N (Edge) min compressive strength of 50 N/mm2 modulus of elasticity of 850 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant, WPC to be laminated with PVC foil of minimum 14 microns thick with hot melt adhesive on both faces as in cupboards, shelves, partitions, kitchen cabinets with full body threaded star headed counter sunk SS screws complete all as specified and as directed. (Note: Auto hinges, SS handles and magnetic catches shall be measured and paid under supply only items separately)

Supply and fix 18mm thick factory made single extruded WPC( Wood Polymer Composite) 100% lead free both side decorative type board comprising of virgin polymer of K value 58-60, calcium carbonate and natural fibres (Wood powder/rice husk.wheat husk) and non toxic additives having minimum density of 650Kg/Cum and screw withdrawal strength of 1800N (Face) and 900N (Edge) min compressive strength of 50 N/mm2 modulus of elasticity of 850 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant, WPC to be laminated with PVC foil of minimum 14 microns thick with hot melt adhesive on both faces as in cupboards, shelves, partitions, kitchen cabinets with full body threaded star headed counter sunk SS screws complete all as specified and as directed. ( Note: Auto hinges, SS handles and magnetic catches shall be measured and paid under supply only items separately)

Supply and fix mild steel Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. not exceeding 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Supply only stainless steel auto hinges(heavy type) four hole for cabinet shutter complete all as specified and as directed.

Supply only stainless steel handles of size 75mm

Supply only magnetic catch for cabinets

Supply and fix 25mm dia curtain rods/rails, mild steel chromium plated/powder coated with fixing brackets, stops, rollers etc complete all as specified and as directed.

Drilling holes for screws, bolts, pipes, etc. not exceeding 25mm dia in stone masonry walls and providing wooden/PVC plug for fixing of cabinets, curtain rod brackets complete all as specified and as directed.

Material and labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab floors, step treads, mid landing (Steps shall be of single piece) including rubbing and mirror polishing complete all as specified and as directed.

Material and labour for 20mm thick screed bed in CM 1:4 to receive stone slab flooring complete all as specified and as directed.

Material and labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab as in riser of steps, skirting, dado and pillars etc including rubbing and mirror polishing complete all as specified and as directed.

Material and labour for 10mm thick rendering in CM 1:3 on block masonry wall/concrete surfaces as in base coat to skirting complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Material and labour for joint free coloured Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

Material and labour for coloured Glazed ceramic tiles in vertical surface 350mmx 250mmx 7 mm/ 450mmX 350mmX 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick CM 1:3 base plaster complete all as specified and as directed.

Material and labour for cement concrete coloured 200mmx200mm /300mmx300mm glossy finished 25mm thick chequered tiles( with mixture of grey cement and pigment) set and jointed in neat cement slurry and pointed in white or colour cement to match over 15mm thick screed in CM 1:4 as in floors complete all as specified and as directed.

Taking down old unserviceable steel windows/ventilators complete of size not exceeding 1.00Sqm each complete all as specified and as directed.

Taking down old steel windows complete of size exceeding 1.00Sqm but not exceeding 1.50 Sqm complete all as specified and as directed.

Taking down old steel windows complete of size exceeding 1.5Sqm but not exceeding 4.00 Sqm complete all as specified and as directed.

Supply and fix of box type steel windows of 80mmx60mmx1.25mm profile for frame, 40mmx20mmx1.0mm double flange profile for glazed shutter, 40mmx20mmx1.0mm tubular section for mesh shutter, 15mmx3mm flat for fixing mesh, telescopic stays, aluminium die cast handle for outside door and flat latch for inside door, 12mm square guard bars @ 100mm C/C with Tee for handle operation, hold fasts 15mmx3mm and 150mm long and finished with a coat of red oxide zinc chromate primer finish complete all as specified and as directed. (Note: Wire mesh, sheet glass shall be measured and paid separately)

Supply and fix steel ventilators fixed type of 60mmx40mmx1.25mm profile for frame, 12mm square guard bars @ 100mm C/C with Tee for handle operation, hold fasts 15mmx3mm and 150mm long and finished with a coat of red oxide zinc chromate primer finish complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) wooden exceeding 1.5 sqm but not exceeding 4.0 Sqm each complete including builders hardware complete all as specified and as directed.

Supply and fix Pressed steel frames for doors 125mmx60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and as directed.

Supply and fix 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with second class hardwood wooden lipping frame complete all as specified and as directed.

Supply and fix 35mm thick factory made II class Hardwood Glazed and skeleton shutters, and prepared to receive glass, gauze, etc. (with sash bars divided into squares), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of member of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

Material and labour for Plain cement concrete 1:3:6 type C1 (using 20mm graded aggregate) as in bed blocks to hold fasts, filling of pressed door frames complete all as specified and as directed.

Supply and fix 200mm Mild steel, semi-barrel tower bolt, open cover, with sheet pressed barrel, stove enamelled black with bright bolt and fixed complete all as specified and as directed.

Supply and fix 150mm Mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed.

Supply and fix 300mm Mild steel sliding door bolts,plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

Material and labour for mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified

Supply and fix Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Supply and fix 4mm thick Sheet glass, ordinary quality and glazing with oil putty or with MS flats with screws in square not exceeding 0.5 sqm in each pane complete all as specified and as directed.

Supply and fix powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

Supply and fix powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed.

Supply and fix 4.8mm thick Sheet glass, ordinary quality and glazing with oil putty or with MS flats with screws in square exceeding 0.5 sqm in each pane including Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and as directed.

Supply and fix first class hardwood moulded Handrails rounded oval shaped with splayed faces in straight lengths 100mmx75mm sunk to fixed to iron frame complete all as specified and as directed.

Supply and fix Vitreous China oval shaped wash hand basin counter sunk of size 630mmx450mmm complete with waste coupling 32mm complete all as specified and directed

Supply and fix PVC waste pipe 32mm dia 75mm long suitable for wash hand basin, kitchen sinks etc complete all as specified and as directed.

Material and labour for 18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platform wall linngs and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Supply and fix pillar taps brass chromium plated fancy type 15mm bore screwed down high pressure for iron pipe complete all as specified and as directed.

Supply and fix bib taps brass chromium plated fancy type 15mm bore screwed down high pressure for iron pipe complete all as specified and as directed.

Supply and fix stop valve/angle cock brass chromium plated fancy type 15mm bore screwed down high pressure for iron pipe complete all as specified and as directed.

Supply and fix Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190grams) complete all as specified and as directed.

Taking up or down steel tubing 20mm bore and connections, including cleaning for re fixing or removal to store complete all as specified and as directed.

Supply and lay 25mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

Supply and fix PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

Supply and fix PVC (SWR) pipes single 110mm bore socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

Supply and fix PVC (SWR) pipes single 110mm bore socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

Supply and fix PVC (SWR) pipes single 75mm bore socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

Supply and fix PVC bends any radius 110mm complete all as specified and as directed.

Supply and fix PVC bends any radius 110mm with access doors complete all as specified and as directed.

Supply and fix PVC bends any radius 75mm complete all as specified and as directed.

Supply and fix PVC bends any radius 75mm with access doors complete all as specified and as directed.

Material and labour for applying a coat of epoxy resin concrete bonding agent NITOBOND EP or its equivalent in approved make on concrete surfaces for bonding new cementitious materials with old concrete surfaces all as per manufacturers instructions complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and as directed.

Material and labour for plain cement concrete 1:2:4 type B1 using 20mm graded aggregate as in copings bed plates, anchor blocks etc including necessary form work complete all as specified and as directed.

Supply and fix mild steel work tubular trusses including special shaped washer etc.posts, rafters, purlins complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 complete all as specified and as directed.

Supply and fix Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.60mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Supply and fix mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe 410 -W Gde E- 250) A quality complete all as specified and as directed.

Material and labour for PCC 1:2:4 type B1 using 20mm graded aggregate 50mm thick finished even and smooth using extra cement as in padding concrete complete all as specified and as directed.

Supply and fix mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Material and labour for providing HS TPO membrane of 1.20mm thick with 200gsm geo textile with overlap joints of 75mm in both longitudinal and transverse direction of the TPO and sealed properly with hot air welding and terminate TPO at the top of parapet with termination strip and fix it by screw 300mm C/c and sealed with HS joint seal PU on top including surface preparation like removing all loose gravels, dirt, oil grease and other foreign particles by jet or dry air and clean the surface mechanically or by grinding to make it smooth before application and providing PCC/cementitious coving of 75mm radius shall be provided at all junctions between vertical and horizontal faces before application of TPO complete all as specified and as directed. (Note: The work is to be carried out through authorised applicator only)

Material and labour for complete removal of existing treatment on walls, washing, rubbing down and stopping of existing treatment and applying two coats of acrylic distemper over a coat of primer including 1.5mm thick wall care putty complete all as specified and as directed.

Material and labour for complete removal of existing treatment on ceiling, washing, rubbing down and stopping of existing treatment and applying two coats of acrylic distemper over a coat of primer including 1.5mm thick wall care putty all as specified and directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of acrylic distemper over a coat of primer including 1.5mm thick wall care putty all as specified and directed.

Material and labour for applying two coats of synthetic enamel paint on new steel surfaces width or girth exceeding 10cm including preparation complete all as specified and as directed.

Material and labour for applying two coats of synthetic enamel paint over a coat of wood primer on new wooden surfaces width or girth exceeding 10cm including preparation complete all as specified and as directed.

Material and labour for applying one coat of synthetic enamel paint over old steel surfaces including preparation complete all as specified and as directed.

Material and labour for one coat of synthetic enamel paint over old wooden surfaces including preparation complete all as specified and as directed.

Material and labour for mild steel TMT bars 6 to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and as directed.

Material and labour for precast reinforced cement concrete 1:2:4 type B1 using 20mm graded aggregate in cover slabs for man holes etc, chullahhoods, chajjas, water troughs, mangers, shelves landings, and similar articles with plain faces set in CM 1:6 complete all as specified and as directed.

Removing building materials obtained from demolition to outside MD land upto 10Km and disposed off under contractors own arrangement complete all as specified and as directed.

Returning, filling in with excavated soil, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removing excavated soil outside MD land upto 10Km and disposed off under contractor own arrangement complete all as specified and as directed.

SPECIAL ITEM OF WORKS Material and labour for 20mm thick rendering in CM 1:6 on stone masonry wall surfaces to receive granite stone complete all as specified and as directed.

Supply and fix 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface reinforced with G.I. wire mesh for fixing in 600 mm x 600mm grid over Gl frame work for ceiling comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and as directed.

Material and labour for double charged coloured Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

Material and labour for complete removal of existing treatment on walls and Finishing walls with Acrylic Smooth exterior paint of required shade Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified and as directed.

Material and labour for preparation of new plastered surfaces and providing Acrylic Smooth exterior paint of required shade Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified and as directed.

SCHEDULE 'A' PART - II (E/M Portion) INTERNAL ELCTRIFICATION Taking down carefully copper / aluminium sub main wiring including teak wood batten / conduit and making good the disturbed surface of walls as directed.

Dismantling and Taking down fluorescent light fitting single /double tube any wattage /any size all as directed.

Taking down / refixing geyser any rating and any size kept in store with out damaging in safe custody and refixing same in position after repair work completed all as specified and as directed.

Taking down carefully unserviceable distribution boards/metal enclosures of any type and capacity including wooden board and making good the disturbed surfaces of walls, ceilings etc including two coats of white/colour washing/ distempering etc to match the existing complete all as directed.

Taking down ceiling fan / Exhaust fan / wall fan, sealing the cable ends dismantling the fan blade kept in safe custody in store completed all as specified.

Refixing / Hanging only ceiling fan / wall fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

Re-Fixing only exhaust fan and connecting up including provision of cable from ceiling rose/connector to fan complete all as specified and directed.

Material and labour for sub main wiring complete with two runs of 2 x 1.5 sqmm FRLS grade PVC insulated unsheathed cable 1100Volt grade multistranded copper conductor drawn through and including PVC conduit and accessories in recessed / surface of wall, roofs etc with one run of PVC insulated copper conductor 1x1.5 Sqmm single core as earth continuity conductor connected with earth dolly and mains complete all as specified and directed.

Material and labour for sub main wiring complete with two runs of 2 x 2.5 sqmm FRLS grade PVC insulated unsheathed cable 1100Volt grade multistranded copper conductor drawn through and including PVC conduit and accessories in recessed / surface of wall, roofs etc with one run of PVC insulated copper conductor 1x2.5 Sqmm single core as earth continuity conductor connected with earth dolly and mains complete all as specified and directed.

Material and labour for sub main wiring complete with two runs of 4 Sqmm single core FRLS grade PVC insulated unsheathed cable 1100Volt grade multistranded copper conductor drawn through and including PVC conduit and accessories in surface of wall, roofs etc with one run of PVC insulated copper conductor 4 Sqmm single core as earth continuity conductor connected with earth dolly and mains complete all as specified and directed.

Material and labour for sub main wiring complete with two runs of 6 Sqmm single core FRLS grade PVC insulated unsheathed cable 1100Volt grade multistranded copper conductor drawn through and including PVC conduit and accessories in surface of wall, roofs etc with two run of PVC insulated copper conductor 6 Sqmm single core as earth continuity conductor connected with earth dolly and mains complete all as specified and directed.

Material and labour for sub main wiring complete with four runs of 10 Sqmm single core FRLS grade PVC insulated unsheathed cable 1100Volt grade multistranded copper conductor drawn through and including PVC conduit and accessories in surface of wall, roofs etc with two run of PVC insulated copper conductor 10 Sqmm single core as earth continuity conductor connected with earth dolly and mains complete all as specified and directed.

Supply and fix modular switch 06 Amps 1 module complete all as specified & directed

Supply and fix modular socket 06 Amps 2/3 pin, 2 module complete all as specified & directed.

Supply and fix modular White cover plate with frame 3 module complete all as specified & directed

Supply and fix modular metal flush box 3 module complete all as specified and directed.

Supply and fix modular White cover plate with frame 6 module complete all as specified & directed

Supply and fix modular metal flush box 6 module complete all as specified and directed.

Supply and fix modular White cover plate with frame 8 module complete all as specified & directed

Supply and fix modular metal flush box 8 module complete all as specified and directed.

Supply and fix modular White cover plate with frame 12 module complete all as specified & directed

Supply and fix modular metal flush box 12 module complete all as specified and directed.

Supply and fix modular switch 16 Amps 1 module complete all as specified & directed

Supply and fix modular socket 06/16 Amps 2/3 pin 2 module complete all as specified & directed.

Supply and fix bell push flush type 5 Amps in replacement of old u/s complete all as specified & directed.

Supply and fix in replacement Door bell AC, 230 volts, single pole in replacement of old u/s bell/ buzzer complete all as specified and directed.

Supply and fix electronic fan regulator modular type, 2 module, 120W complete all as specified and directed.

Supply and fix ceiling rose surface three terminals in replacement of old unserviceable complete all as specified & directed.

Supply and fix LED fitting of 6 watts - Square surface mounted LED flat panel down light, PDC aluminum housing and PMMA diffuser makes it a robust Luminaire alongwith 6W LED lamp complete all as specified and as directed.

Supply and fix decorative wall light, gold finish fixture with white glass diffuser suitable for 7.5 watt LED Filament lamp warm light complete all as specified and directed by Engr-in-Charge.

Supply and fix LED Wall light of cap 15 watt warm light, environment friendly, new generation, energy saving, decorative IP 66 LED up-down luminaries with wall surface mounting using COB LED as light source complete all as specified and directed by Engr-in-Charge.

Supply and fix decorative light upto 7.5 W A60 LED Filament lamp black / white surface mounted conical shape pendant in black and white colour complete all as specified and directed.

Supply and fix LED PC batten light fitting of 4 feet 20 watt, with energy efficient LED and integrated electronic driver of 20W fitting including connecting up with three core flexible copper conductor upto ceiling rose complete all as specified and directed.

Supply and fix LED PC batten light fitting of 2 feet 10 watt, with energy efficient LED and integrated electronic driver of 10W fitting including connecting up with three core flexible copper conductor upto ceiling rose complete all as specified and directed.

Supply and fix 36W LED Fitting, 2 x 2 recess / Surface LED flat panel with high brightness LED for glare free homogenous illumination including LED driver complete all as specified and as directed.

Supply and fix 35 W LED Street Light fitting pressure die cast aluminium housing, heat resistance toughened glass, IP-66 protection fittings including suitable size of GI bracket, fixing with nut and bolts complete all as specified and directed.

Supply and fix ceiling fans complete including anti suicide rods with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

Supply and fix "S" Hooks for ceiling fans hanging of size 1200 mm sweep making hole on roof for fixing "S" hooks of 10mm dia MS and making good for damaged surfaces complete all as specified and as directed

Supply and fix MCB SPN 32 Amps, 'C' series, 240 V complete including making connections all as specified and directed.

Supply and fix MCB SP 6-32 Amps, 'C' series, 240 V complete including making connections all as specified and directed.

Supply and fix MCB DB SPN 12Way with 200 Amps rated busbar, Double door, flush to wall including all cutting etc on wall and making good the disturbed surfaces to match the existing complete all as specified and directed.

Supply and fix MCB DB SPN 8 Way with 200 Amps rated busbar, Double door, flush to wall including all cutting etc on wall and making good the disturbed surfaces to match the existing complete all as specified and directed.

Supply and fix in repair MCCB DB Vertical TPN 4 Way 'A' Frame, Including MCCB TPN 63 Amp Breaking capacity 16 KA -01 nos, Double Door flush to wall including all cutting etc on wall including making good the disturbed surfaces to match the existing in replacement of old U/s complete all as specified and directed.

Supply and fix in repair MCCB DB Vertical TPN 8 Way 'A' Frame, Including MCCB TPN 125 Amp Breaking capacity 25Ka -01 nos, Double Door flush to wall including all cutting etc on wall including making good the disturbed surfaces to match the existing in replacement of old U/s complete all as specified and directed.

Supply and fix in replacement single pole and neutral enclosure with two pin and earth plug and socket including 1Nos MCB 20Amps capacity complete all as specified and directed by Engr-in-charge

Supply and fix MCB TP 63 Amps including making connections all as specified and directed.

Supply and fix MCB DB TPN 4Way, Double Door flush to wall including all cutting etc on wall including making good the disturbed surfaces to match the existing in replacement of old U/s complete all as specified and directed.

Supply and fix MCB TPN 40/63 Amps including making connections all as specified and directed.

Removal of bollards carefully and keep in store for safe custody and after civil works re-fixing the same complete all as specified and directed by Engr-in-Charge.

Supply and fix LED bollard in decorative mushroom shape with IP-65 protection of cap 9 watt including necessary form work/PCC work complete all as specified and directed.

Material and labour for Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 M below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt , earth lead GI wire 4mm dia (8 SWG) connected to GI earth plate electrode by means of bolts, nuts, check nuts and washers of galvanised iron and thimbles and other end of earth wire connected to main switch board and protected by galvanised iron pipe medium grade 15mm bore and 20mm bore light grade GI pipe with funnel and wire mesh for watering including necessary excavation and earth works. PCC Chamber in cement concrete 1:3:6 type C-2 & RCC cover in M-20 (Design mix ) and all as shown in Electrical Plate No. 3 of SSR ( Part-I) of 2009 complete all as specified and as directed. Note: The rate quoted is inclusive of GI earth wire 4mm dia upto 7.5m length.

Supply and fix GI earth wire 4.00 mm dia for interconnecting of earth electrodes complete all as specified and as directed.

EXTERNAL ELECTRIC SUPPLY Taking up underground unserviceable cable of any size from existing trench including bricks, etc and removing of materials from work site complete all as specified and as directed.

Excavation in trenches in soft /loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre deep for laying of cables etc, getting out and forming bottom surface to required gradient complete all as specified and as directed.

Removing excavated material not exc 50m and depositing where directed at a level not exc 1.5m above the starting point in soils complete all as specified and as directed.

Supply, laying riddled earth soil conformed to IS-1255, cushioning to cables with a layer of riddle earth soil 15cm deep before laying the cable and 8 cm depth after laying of cable, complete all as specified and as directed.

Supply and lay Brick protection cover on cable with sub class 'B' brick, laid dry and flat adjacent to each other complete all as specified and as directed.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 sqmm 4 core complete all as specified and as directed.

All as per item No 157 above but size 50 sqmm 3.5 core

All as per item No 157 above but size 70 sqmm 3.5 core

All as per item No 157 above but size 95 sqmm 3.5 core

Material and labour for boring of holes under road, pavement hard standing by trenchless technology using ultra sound technique and necessary machine including HDPE pipe upto 150 mm dia suitable for 0.4 mpa working pressure complete all as specified and as directed.

Material and labour for G.I. tubing light grade of size 50 mm bore for protection of cables to be laid under roads, crossings/culverts complete all as specified and directed.

All as per Srl item No 162 here in above but GI pipe of size 80mm bore

Material and labour for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundations for electric poles, filling and mass concrete complete all as specified and directed.

COOLING APPLIANCES Taking down Split AC 1.5/2 Ton capacity (Indoor and Out door Unit) with stabilizer by removing all electrical connections and indoor to out door unit gas pipes, nut bolts from roof top of bldg before starting of civil work and shifting to store for safe custody. After completion of civil work, Refixing /installing Split AC 1.5/2 Ton with voltage stabilizer at the suitable place by connecting all electrical connections and copper piping with insulation (5/8th x 1/4th) with nut bolts as per site requirement, testing and commissioning complete all as specified and as directed By Engr- In - Charge. Note: if any extra cable, gas pipes, gas filling require at the time of installation the quoted rate is deemed to be included, No extra cost will be paid to contractor.

PRAGATHI BUILDERS (BID ID -3362716)

C R R CONSTRUCTIONS (BID ID -3362129)

B5BUILDING SOLUTIONS (BID ID -3361595)

PRACHANIVA CONSTRUCTIONS (BID ID -3369523)

M/s M Munivenkatappa and Company (BID ID -3369351)