Special repair of Ty-V quarter No. BL-5 at Biggi Line under Supply Line Section, SD-II, PBND, APWD, Port Blair during 2020-21

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.

Beyond 120 cm girth upto and including 240 cm girth

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources).

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, ifnishing and reinforcement- All work up to plinth level :

1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Electric resistance or induction butt welded tubes

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).

Medium shade pigment using 50% white cement 50% Grey cement

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).

6 mm thick Cement fiber board as per IS: 14862

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

Water thinnable cement primer

Finishing walls with water proofing cement paint of required shade :

New work (Two or more coats applied @ 3.84 kg/10 sqm)

Applying priming coat:

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work

Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (One or more coat applied @ 0.90 ltr/10 sqm).

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles 10 mm to 25 mm

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :

15 mm to 40 mm nominal bore

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

10 litre capacity - White

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe, 32 mm dia

Providing and fixing soil, waste and vent pipes :

75 mm diameter : Sand cast iron S&S pipe as per IS: 1729

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

75 mm dia Sand cast iron S&S as per IS - 1729

Providing and fixing plain bend of required degree.

75 mm dia Sand cast iron S&S as per IS -1729

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

100 mm inlet and 100 mm outlet Sand Cast Iron S&S as per IS: 1729

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

20 mm nominal dia Pipes

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length 15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

100 mm diameter

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15 mm nominal bore

Providing and fixing wood work in frames of false ceiling, partition etc sawn and put up in position with

Superior hardwood cat-II (A)

Providing and fixing plain square edged wooden beading 50 x12 mm section with screws of approved quality for ceiling with

Superior hardwood cat-II (A)

Providing and fixing CPVC union socket of approved quality, Colour and make etc complete.

20mm dia

Providing and fixing 19mm marine plywood (Green ply or equivalent) conforming to IS-710-1981 weather boarded walling with frames wrought framed and fixed 75 X 75 mm standard hard wood cat-II as per the direction of Engineer-in-charge.

Providing and fixing CPVC gate valve of approved quality (screwed end).

20mm nominal bore

SANGAM ENTERPRISES

Raj Construction

V.S.K.BUILDERS

NIKHIL BISWAS

DIYA ENTERPRISES

ARJUN MANDAL

M/s V ALAGAR SAMY & SONS