SPL REPAIR OF BLDG NO T11 AT ASC BN UNDER GE N AKHNOOR

Amount

Taking down old unsv roof treatment including PCC padding if any, plastering, removing existing bitumen felt treatment including brushing, cleaning top surface of roof slab, brooming etc incl disposing off debris from MoD land complete all as specified and directed.

Rendering 10mm thick cement plaster with cement mortar (1:4) on fair finish of brick work or concrete surfaces of roof slab complete all as specified.

Roof treatment :- Water proofing treatment to RCC roof slab including parapet as under :- (a) 1st Course : Apply a coat of bituminous primer conforming to IS-3384@ 0.40 Kg /Sqm on prepared surface of plaster and after drying of primer. (b) 2nd Course : Applying evenly a tack coat of industrial bitumen grade 85/25 conforming to IS-702 at rate of 1.2 Kg/Sqm. (c) 3rd Course : APP (Atactic Polypropylene) modified polymeric membrane, 5 layered, 3 mm thick weight not less than 3.0 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 150 mm end overlap, membrane has to be laid with LPG torch and overlap sealed and finished neat, all joints. (d) 4th Course : Apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm over membrane and dusted with dry sand @ 0.50 to 1 Kg/sqm. (i) On Non-accesible roof : After providing (a) to (c) provide aluminium paint as per manufacturer instructions. (ii) Coved fillet in PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) of required radius 75mm shall be provided at the junction of roof and vertical surface such as parapet wall/mumty around opening and treatment mentioned above shall be applied followed by a cement plaster 20mm thick in cement mortar(1:6). Note : (i) Roof treatment work shall be carried out through approved manufacturers only or through their authorised personal only.

Sunken Floor treatment :- Providing and laying of water proofing treatment to sunken portion including vertical portion by applying cement slurry mixed with acrylic based polymer modified cementitious composite compound of make as specified and approved including demolition and filling of sunken floor with & including laying of PCC 1:5:10 type E-2 (using 40mm brick aggregate). (a) First layer of slurry of cement @0.488 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.253 Kg/Sqm. This layer allowed to air cure for 4 Hours. (b) Second layer of slurry of cement @0.242 kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.125 Kg/Sqm. This layer allowed to air cure for 4 Hours.

Note:(a) Concrete for sunken slabs shall be mixed with WP compounds as per manufacturer's instructions. Before carrying out water proofing treatment the sunken slab shall be tested with water for 48 hours for any leakage /dampness is seen in ceiling below, then treatment is again carried out to RCC slab and it is again tested before passing for next stage. (The rate quoted includes water proofing compound as per manufacturers instructions). (b) Please note that only floor area shall be measured for payment purpose.

Dismantling of AC/CGI/Galvalume sheets corrugated or semi-corrugated in roof covering including ridges, hips, valleys and flashings etc complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified and as directed.

Structural steel work as in roof trusses (framed), trussed purlins, crane gantries, rails and fastening and heavy brackets (Beam, tee, angle, channel or hollow steel section) including distance pieces, cleats etc confirming to Fe-410-W (Gde-E-250) quality B complete all as specified and directed

Pre-painted galvalume aluminum zinc coating GI based corrugated sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) of any type and any thickness including cover fillets/GI grid framework complete all as specified and directed.

4mm thick prelaminated designer ceiling board over & including GI snap grid frame work (Grid size 600x600mm) with powder coated GI angle of size 25x25x3mm fixed along wall perimeter, main runner 'T' of size 25x40x3mm , secondary runner 'T' of size 25x30x3mm suspended with 3mm GI wire @ 1200mm c/c of ceiling by fasteners of adjustable guide hanger including clips/MS fitments to hold the panels, complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, culverts,etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified and as directed .

Brick work with old size sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified.

Brick work with sub class B brick straight or curved on plan to any radius in half brick thick built in CM 1:4 complete all as specified and directed.

Taking down cement plaster from brick or stone walls incl racking out joints hacking for key, scrubbing down with water etc all as specified and directed.

Rendering 15mm thick cement plaster with cement mortar(1:4) on fair finishes of brick work or concrete surface of roof slab, complete all as specified and directed.

Rendering 10 mm thick cement plaster with cement mortar(1:6) on other than fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

Rendering 5mm thick cement plaster with cement mortar(1:3) on concrete surface as in ceiling finished the surface even and smooth without using extra cement, complete all as specified and directed.

Supply only integral water proofing admixture

Repair to Roof projection/Chajjas/ Facia including taking down old worn out rendering and Rendering 15mm thick on external wall surfaces (ht upto 7.0 m from ground level) in cement mortar 1:4 finished fair and even without using extra cement using GI wire netting 0.90mm dia and 12mm mesh lathing, complete all as specified. Note : (i) Rate quoted are deemed to incl double scaffolding and wire netting reqd in the work.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over one coat of chalk whitening on plastered surfaces preparatory to distemper complete all as specified and directed.

Preparation new decorated surfaces of walls surfaces and applying two coat of exterior emulsion paint (wheather proof Apex paint only) over a coat of approved primer over 2mm thick wall care putty complete all as specified and as directed.

Preparation of newly plastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed.

Complete removal of old existing treatment of wall and washing, rubbing down and stopping of distempered surfaces complete all as specified and directed.

Applying wall care putty of 1-2 mm thick over new plastered /old plastered surface of wall complete all as specified and directed.

Preparation of surfaces of wall on new /old untreated surface finished with putty and applying two coat of oil bound disterper over one coat of primer all as specified and directed.

Complete removal of old existing treatement of wall upto plaster level with mechanical means including cleaning washing,rubbing etc. and applying two coats of exterior emulsion paint (weather proof Apex paint only) over a coat of approved primer over 2mm thick walll care putty complete as specified and directed.

Preparation of old plastered surfaces of ceiling and applying two coat of white wash complete all as directed.

S&F in repair 25mm dia stainless steel curtain rod complete with stainless bracket and side caps fixed in position by drilling holes in wall and fixed the bracket with rawl plug and stainless steel screw all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc. complete all as specified and directed.

Machine cut kota stone slab as in flooring, of size not less than 53x53cm and 20-25mm thick laid and jointed with grey cement slurry and mixed with pigment to match the shade of slab including rubbing and polishing to 100mm wide marble patti/border all around including 15mm thick screed bed in CM (1:4) Complete all as specified and as directed.

Machine cut kota stone in vertical surfaces such as riser of steps skirting dado and pillar etc over and including 10mm thick plaster in CM 1:4 Complete all as specified and as directed.

20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windown-cills, cooking platform in counter WHB and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixure of pigment to match with shade of granite complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Reinforced cement concrete 1:2:4, type B1 (20mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors roors, landings, balconies, canopies, deck slabs and in shelves and the like including use and waste of formwork complete all as specified and directed.

TMT bars 8mm dia bar and over cut to length, bent to shape required including cranking, bending, hooking ends, binding, with and including mild steel wire (annealed) not less than steel wire 0.9mm dia or securing with clips and confirming to FE 410-S and 310-0), complete all as specified and directed.

Providing Plain cement concrete type C-2, 1:3:6 ( using 40mm graded crushed stone aggregate), 750mm wide and 50mm thick as in plinth protection laid in bays not exceeding 2 Sqm each and finishing even and fair on top without using extra cement with 6mm wide joints throughout the thickness of plinth protection, filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand (all by weight). Complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles laid over & including 15 mm thick screed bed in cement and sand mortar 1:4, complete all as specified and directed.

Description all as per Srl item No 40 here-in-before, but on skirting 15mm thick in cement mortar 1:4 all as specified and directed.

Plain Cement Concrete 1:2:4 Type B-0 40mm thick (12.5 mm graded aggregrate) as in floor finished even and fair for receiving tiles complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match including 15 mm thick screed bed in cement and sand mortar 1:6, complete all as specified and directed.

Glazed ceramic tiles coloured in vertical surfaces of size 450x350x7mm thick , jointing in neat cement slurry and pointing in colour cement to match including incl 10mm thick in plaster in cement and sand mortar 1:4 finished even and rough all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each but not exceeding 4 sqmm all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each and removing from site complete all as specified and directed.

Taking down shutter of any description area exc 1 sqm but not exc 2.0 sqm each complete all as specified and directed.

Powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified.

Powder coated aluminium anodised door shutters(minimum thickness of powder coating 50 micron), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed.

Powder coated anodised aluminium window / ventilator( glazed / gauged skeleton shutter ), (minimum thickness of powder coating 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinges type B-21 100mm long (2 No. ) suitable handle (1 No.) complete all as specified and as directed.

Powder coated aluminium anodised door shutters(minimum thickness of powder coating 50 micron), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed.

Anodised Aluminium Grill powder caoting (anodised transparent or dying to required shade according to IS 1868 with minimum anodised coating of grade AC 15) of approved design pattern with approved standerd section and fixed to existing window framewith Brass/stainless stell screw@200mm c/c incl cutting grill to proper opening size for fixing and operation of handle etc. complete all as specified.

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or FE 310-0 complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site, complete all as specified and as directed.

Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube, supplying and fixing in opening as per specification and drawing, complete all as specified and directed.

Pressed steel frames for doors with one or more rebates of size 105x60mm including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh hold bar complete all as specified and as directed.

Pressed steel frames for doors with one or more rebates of size 125x60mm including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh hold bar complete all as specified and as directed.

Plain Cement Concrete 1:2:4 type B-0 (Using 12.5 mm graded crushed stone aggregate) as in filling of roof kerbs or pressed steel frame as in 50 mm parapet coping, roof kerbs or in lintels upto 1.5m clear span, cills, plinth courses, string courses, coping, kneelers etc all as specified and directed.

35mm thick, 2nd class soft wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated, complete all as specified and directed.

35mm thick 2nd class soft wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkhats complete, all as specified and directed.

Mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified and directed.

Extruded aluminium alloy handles, fabricated type, anodised of size 150mm and fixed, complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section of size 200mm and fixed, complete all as specified and directed.

300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section of cast aluminium alloy and fixed, all as specified and directed.

300mm Mild steel ordinary rat tail helical door springs including roller and roller plate fixed, complete all as specified and directed.

3mm thick figured glass, pin head type and glazing with oil putty in squares in exc 0.5 sq.m in each pane, complete all as specified and directed.

3 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and directed.

Galvanised steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed all as specified and directed.

Floor door stopper 140mm overall length of cover plate of aluminium alloy body and tongue,nodised,with hard drawn steel spring,fixed in bottom body of door complete all as specified and directed.

Preparation of new steel and iron surfaces over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide complete all as specified and directed.

Preparation of new untreated wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and painting with two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

Preparation of old steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with one coat of synthetic enamel paint all as specified and directed.

Preparation of old wood or wood based surfaces of any description not otherwise described over 10 cm in width or girth, and appying one coat of synthetic enamel paint complete all as specified and as directed.

Chequered cement concrete tiles 300x300x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment to match shed of tiles, laid over and including 20mm thick screed bed in CM 1:4, complete all as specified and directed.

75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base to flooring/path etc, finishing even & rough to receive wearing surface complete all as specified and directed.

Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) 3 layered hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified.

Taking down old steel water tubing of 15mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as requiered, complete all as specified.

Taking down old steel water tubing of 20mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as requiered, complete all as specified.

Steel water tubing 15mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceiling or laid in floors, complete all as specified.

Steel water tubing 20mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceiling or laid in floors, complete all as specified.

Refixing old steel water tubing of 15mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as requiered, complete all as specified.

Refixing old steel water tubing of 20mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as requiered, complete all as specified.

Bib tap 15 mm bore with flange, Brass CP, fancy type(long body). with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repairs, complete all as specified and as directed.

Stop valves/angle valve, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, for bore dia of pipe 15 mm, supplied and fixed in repairs complete all as specified.

15 mm dia bore stop valves (concealed type) with long shank and cup fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fixed in repairs complete all as specified and as directed.

Pillar tap fancy type capstan heads, chromium plated screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed in repairs complete all as specified and directed.

Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20 mm dia (minimum weight 210 gms) complete all as specified and directed.

20 mm bore gun metal globe or gate valve with iron wheel head screwed both end for iron pipe fixed in repairs complete all as specified and directed.

PVC valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete, fixed in repairs complete all as specified and as directed.

Vitreous china squatting pan "Orissa Pattern" size 580 x 440 mm in white colour with integral foot rest incl lime mortor, 'S' trap fixed in repairs complete all as specified and directed. Cat Part No-20042 (ORISSA PAN (ECO)) of Hindware or equivalent cat part of make specified in list make as approved by GE.

Vitreous china wash down water closet pan pedestal pattern in white colour excluding seat cover, flushing cistern and flush pipe fixed in repairs complete all as specified and directed. Cat Part No-20011 (SLICK) of Hindware or equivalent cat part of make specified in list make as approved by GE.

Brass chromium plated health faucet with one metre long flexible tube and wall hook fixed to iron pipe fixed in repairs complete all as specified and directed.

Plastic water closet seat cover white closed pattern with flat bottom and mild steel chromium plated or aluminium hinging devices fixed in repairs complete all as specified and directed.

Vitreous china urinal half stall flat back, size 465 x 355 x 265 mm, white , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and union for discharge pipe fixed in repairs, complete all as specified and directed.

Supply and fixing in repairs table top basin of size 170x835x455mm/ 565x425x140mm of whitecolour complete all as specified and approved.

PVC connection 15mm size with PTMT nuts on both ends of length 450mm fixed in repairs, complete all as specified.

Chromium plated brass towel rail 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls and fixed in repairs complete all as specified and as directed.

Supply only brass chromium plated shower roses 125mm with or without swivel joints all as specified and directed.

15mm bore two in one bib taps with flange, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs all as specified Make- Jaquar Cat Part No -FON-40041/ORP10041PM or its equivalent as specified in the list of makes as approved.

Taking down eaves gutter and rain water pipe, soil and waste pipe (any size or pattern), including all fittings, heads , shoes bends , swan-necks etc. Complete all as specified and directed.

110mm bore PVC SWR Type-B pipes (pressure not less than 6 kg /cm2) single socket in any length with rubber joints laid in floors/trenches etc all as specified and directed.

110 mm dia PVC (SWR) Type-B pipes single socketed in any length with rubber ring joint fixed to wall with PVC//MS holder clamp all as specified and directed.

75mm bore PVC SWR Type-B (pressure not less than 6 Kg/cm2) pipes single socket in any length with rubber joints fixed in floors etc all as specified and directed.

75mm bore PVC SWR Type-B (pressure not less than 6 Kg/cm2) pipes single socket in any length with rubber joints fixed to wall with PVC/MS holder clamp etc complete all as specified and as directed.

PVC SWR reducer 110mm to 75 mm complete all as specified and directed.

PVC SWR Type-B cowls 75mm bore all as complete all as specified and directed.

110mm bore PVC Bends (any radius) for pvc pipes complete all as specified and directed.

PVC (SWR) bends any radius 110mm dia with oval access doors complete all as specified and directed.

110mm PVC (SWR) junction single, (single T) equal or unequal provided with access door, complete all as specified and directed.

PVC (SWR) bends any radius 75mm dia complete all as specified and directed.

PVC (SWR) bends with access door 75mm dia complete all as specified and directed.

PVC (SWR) junction single (single T) equal or unequal 75 mm dia all as specified and directed.

PVC (SWR) 75 mm dia floor trap plain with grating including jointing with solvent cement fixed in repairs, all as specified and directed.

PVC (SWR) branch piece of 110 bore pipe, single (single Y) equal or unequal ordinary or inverted (spigot or socket type) provided with access door complete all as specified and directed.

PVC (SWR) branch piece of 75 bore pipe, single (single Y) equal or unequal ordinary or inverted (spigot or socket type) provided with access door complete all as specified and directed.

Supply and fixing in repair only PVC waste pipe for WHB/Urinal/Sink for 32/40mm dia all as specified and directed.

Plain Cement Concrete (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregates) as in coping and eadges of path, roof kerb including weathering, slightly rounded or chamfered angle and throating, necessary form work finishing all exposed faces of concrete etc complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete,including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement at necessary holes for smooth finishing complete all as specified and directed complete all as specified and directed.

Material and labour for point wiring complete with 1.5 sqmm PVC insulated, FRLS type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC casing capping 20 mm dia medium grade and including cutting, chasing work at any height and all accessories are surface in walls / roofs / floors / ceiling etc. metal flush box with top,bottom,side/back wall knockout for conduit entry from any direction made out of 1.60mm thick suitable for fixing of modular top cover plate as per numbers of switch modules for modular switches,sockets,fan regulators,red colour indicator, blank plates etc as approved coloures and including 1.5 Sqmm PVC insulated multistranded FRLS type unsheathed(Green colour),single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat including providing putty and white cement for smooth finishing of existing surface complete all as specified and directed for the following:- Make of Cables Havells, KEI, Grandlay (Note:- All necessary accessories such as modular steel box,top cover plate, blank plate, screws,washers and all modular electrical fixtures are to be used of same make/brand only and shall be deemed in to included in quoted rate only.)

-Ditto- All as per srl item No 120 above, but One light point/fan /bell point controlled by one switch.

-Ditto- All as per srl item No 120 above, but One 5 pin 6 amps socket point controlled by one 6 amps switch on independent board .

-Ditto- All as per srl item No 120 above, but One 5 pin 6 amps socket point controlled by one 6 amps switch on same board .

-Ditto- All as per item No 120 above but point wiring with 2.5 sqmm with earth conductor of size 2.5 sqmm complete all as specified and directed for the following:- (a) One 6 Pin 16/6 amps socket outlet point controlled by one 16 amps switch on independent board.

Modular type switch 06 Amps, single pole,1way, 1 module,240V, ISI Marked complete all as specified and directed.

Modular type switch 16 Amps, single pole, 1way,1 module, 240V, ISI Marked Complete all as specified and directed. Make- Crabtree (Havells) or its equivalent in Anchor (Roma), Legrand, Seimens as approved”.

Modular type socket shuttered type 6 Amps, 2/3 Pin combined 2 module, 240V, AC ISI Marked Complete all as specified and directed.

Modular type socket 6 A/16 Amps, 2/3 Pin combined shuttered socket 2 module with light indication ,240V,AC ISI Marked Complete all as specified and directed .

Angle lamp holder, insulated body with back plate for LED lamp including removing old unsv item complete all as specified and directed.

Ceiling rose, 3 terminal ,PVC/polycarbonate body ISI marked, complete all as specified and directed

LED light fitting 1x20W, 4 feet, 220V, general purpose surface and wall mounted LED batten with aluminium housing integrated electronic driver LED fitting connecting up with three core flexible copper conductor cable of suitable size from ceiling rose as approved by GE fixed in repairs complete all as specified and directed.

LED light fitting 1x10W, 2 feet, 220V, general purpose surface and wall mounted LED batten with aluminium housing integrated electronic driver LED fitting connecting up with three core flexible copper conductor cable of suitable size from ceiling rose as approved by GE fixed in repairs complete all as specified and directed.

LED INVERTER batten of 20 watt, 4 feet with square profile and poly carbonate channel lithium ion battery with charging time 8 to 10 hours and backup time upto 4 hours and connecting up with twin core twisted copper wire from LED fitting to ceiling rose and removing old unserviceable fitting complete all as specified and directed. Make: Pride plus inverter batten 4 feet, 20W 6500K of Havells or equivalent in Bajaj, Surya, Wipro as approved by GE.

LED bulb 12 watts, 240Volts,50Hz pin type and including removing old unserviceable item complete all as specified and directed.

LED secruity light fitting of capacity 25 Watt LED street light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with suitable inbuilt surge protector and cable connection from ceiling rose to light fitting and testing and including removing of old unserviceable item complete all as specified and directed. Make-Havells Cat Part No-ENXTP25L WH PO PC SD of Bajaj or its equivalent in Havells or Wipro as approved by GE.

Supply & fixing and in repair sheet metal enclosure acrylic door 240 volts AC,SPN distribution board 4 way suitable for flush mounting with 100amps copper busbar,neutral bar,earth bar and MCB incomer of rating upto 100Amps ,MCB SPN/DP, and MCB SP as outgoing and complete connecting cable links with top and bottom removable gland plate with IP 43 DBs protection and including making good the disturbed surfaces to match with existing surface and colour coat all as specified and as directed. Make:- Legrand cat No. 5076 21 8 way / Hager Cat Part No.VYS04G / L&T Cat Part No-DBSPN004GD as approved by GE.

MCB SP 6 to 32 Amps 10 KA,"C" series,AC,240Volts,50Hz , ISI marked fixed in repairs complete all as specified and directed. Make:- Legrand cat No.4085 87 to 4085 95 / Hager Cat Ref No.NCN106N to NCN132N / Havells Cat No.DHMGCSPF006-032 as approved by GE.

MCB single pole & neutral 40 to 63 amps 240 volts 10 KA 'C' series fixed in repair, complete all as specified. Make:-Havells cat part No-DHMGCSPF040or its equivalent cat part of make-Legrand / ABB / L&T as approved by GE

Earthing complete with galvanised steel earth plate electrode 600mmX 600mmX 6mm thick buried directly in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres below ground level, connected to and including galvanised iron wire 4 mm dia and light grade protection pipe of 15 mm dia from earth electrode up to test point or up to 7.5mtr whichever is less by means of GI bolts, nuts, check nuts and washers all as per electrical plate No 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade,GI funnel with wire mesh,including charcoal, salt packed all around the earth electrode plate in layers, PCC earth pit chamber 1:3:6 type C1, of size 45X 45X 45 CM,RCC cover 1:2:4 type B1 of size 45X45X6 CM with Reinforcement bars of 8mm dia @120mm c/c excavation/earth work in any strata and returning filling, removal of surplus soil and testing/test point for required value including removing old item complete all as specified and directed.

Exhaust fan single phase metal body, AC 230 Volt, 50 Hz, 900 RPM of size 300mm sweep with louvers shutter complete with all accessories including connecting up from ceiling rose complete all as specified and directed. Make:- Cat part No:- Turbo Force 1P Grey of Havells or its Equivalent cat part of make-BAJAJ,CROMPTON GREAVES, GEC, KHAITAN,ORIENT as approved by GE

Sub main wiring complete with 2 runs of 6 sqmm single core copper conductor (ISI marked)cable 1100 volts grade,FRLS type, PVC insulated, unsheathed, flexible, multi stranded colour coded cables drawn through rigid PVC conduit of size 25 mm dia medium grade(MMS) with all connected accessories such as Bend,Tee,Elbow,Short peices etc concealed in wall/roofs/floors and including one run of 2.5 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade,FRLS type as earth continuity conductor connected to common earth dolly including making good the disturbed surfaces to match with existing surface including taking down of old existing submain cable complete all as specified and directed. Note : - Two run of 6 sqmm single core copper conductor cable and one run of 2.5 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit.

Ceiling fans complete with blades. Down rods, electronic regulator and accessories, 230 volt, 1200mm sweep, min air delivery 210 CFM with service value 6 BEE five star rated with brushless direct current motor (BLDC) incl taking down existing and depositing the same in MES store yard. All as specified and directed. “Cat Part No Zinger Make Havells or its Equivalent in Orient, Usha.” as approved by GE.

Vertical double door TPN in replacement are fitted with Bus bar neutral link, blanking plates of 4 way(4+12) with suitable for incomming MCCB 4 pole 'G' frame,having isolated neutral bar, mechanical impact strength IK09, door earthing suitable for MCCB upto 125 Amp, complete all as specified and directed. Make:-Havells Cat part No:- DHDLVDRWGOFO04 or its Equivalent cat part of make of Legrand / ABB / L&T as approved by GE.

MCCB 04 pole 415 volts 16 KA, 63 Amp adjustable thermal & fixed magnetic setting type suitable for TPN vertical loadline DB mentioned at ser No 15 here in before fixed in replacement, complete all as specified and directed. Make : Havells Cat part No IHDA3BBF0063 or its Equivalent cat part of make of Legrand / ABB / L&T as approved by GE.

Supply and fixing in replacement electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece incl making holes on walls for proper fixing with nuts and bolts complete making the surface good as per existing all as specified and directed of one of the makes as in list of makes and as approved by GE. Note:- Old Unserviceable geysers shall be deposited to MES store yard.

bushan kumar (BID ID -3400600)

PACHNANDA BUILDERS (BID ID -3401861)

M/s Rajesh Kumar Contractor (BID ID -3404719)

M/s Chopra Constructions (BID ID -3397087)

M/S KARAN SINGH CONTRACTOR (BID ID -3409171)

M/s Vishwakarma Enterprises (BID ID -3411702)

M/S JEEVAN LAL SHARMA (BID ID -3412941)