SPECIAL REPAIR OF SUB HEALTH CENTRE UNDER H.W.C. PROGRAMME AT VILLAGE BASIRPUR IN MOHINDERGARH DISTRICT

Amount

Earth work in excavation in foundations, trenches, etc.in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres(HSR 6.6)

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing, (b) in cement (HSR 8.5 b)

Dismantling Concrete reinforced cement concrete with cleaning and straightening and cutting of bars if required (HSR 8.6) (e)

Scraping cement plaster (HSR 8.32) ( c )

Scraping white wash and colour wash. (HSR 8.32) (a)

Cement Concrete 1:4:8 with stone aggregate 40mm nominal size in foundation and plinth.(HSR 10.39)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position complete in all respects. (HSR 10.82 + 10.95) (A)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work in shelves excluding steel-reinforcement but including centring and shuttering, laid in position complete in all respects. (HSR 10.81 + 10.95) a

First class brick laid in cement sand mortar 1:4 in foundation and plinth. (HSR 11.4)

First class brick laid in cement sand mortar 1:5 in foundation and plinth(HSR 11.3)

First class brickwork laid in cement sand mortar 1:6 in first storey upto 4 meters above plinth level.(HSR 11.7)

Terracing consisting of tiles 22.86 cm x 11.43 Cm x 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13).

Top khurra 0.6 m x 0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 over 50 mm thick cement concrete 1:8:16(HSR 13.50)

Bottom khurra on ground 1:2 m X 0.6 m consisting of brick-on-edge laid in cement mortar 1:3 over 75 mm cement concrete 1:8:16 including 12 mm thick cement plaster 1:3(HSR 13.57)

Cement Concrete 1:2:4 gola 10cm x 10cm quadrant along junction of roof with parapet wall finished smooth, where specified. (HSR 13.64).

Base course of floors consisting of 100 mm thick cement 1:8:16 and 100 mm sand or stone filling(HSR 14.1)

Providing and fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. (HSR 14.91) Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, JOHNSONS & RAK.

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shade except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (HSR 14.92) ii

12 mm thick cement plaster 1:3 (HSR 15.4)

12 mm thick cement plaster 1:6 (HSR 15.7)

15 mm thick cement plaster 1:6 on the rough side of single or half brick wal (HSR 15.12)

Factory manufactured wire gauze door and window shutters of commercial hard wood such as Hollock, Champ, Chikrassy & Chaplash only. (non-coniferous timber other teak conforming to I.S. specification No. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position. (Styles and rails of windows shutter shall be 75 mm wide. (i) 35 mm thick. [HSR 17.92 (ii) - Note (HSR 17.18)

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (Note:- reputed make such as Duro, Green, Kitply will be used as approved by Engineer-in-charge). HSR 17.93 (a) (iii) 35 mm thick - Note (HSR 17.18)

Factory –manufactured panelled door shutters,of teak wood,kiln-seasoned, as per I.S.specification no.401,with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 12 mm thick veneered,particle board, or plywood of B.W.R.grade hot-pressed including the cost of iron hinges,screws,chocks/cleats,stops and nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above but including labour for fixing the same in position). (a) Panel of decorative plywood, one side teak faced, and other side commercial faced (HSR 17.94) 35 mm thick - Note (HSR 17.18)

Teak wood chowkats of doors and windows including iron hold fasts, corner straps, screws, bolts for hold fasts, etc., complete fixed in position. (HSR 17.13)

FE-500 EQR TMT steel bar for RCC works, where not included in the complete rate of RCC including bending, binding & placing in the position complete. (NS) Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. From the length so measured, the weight of reinforcement shall be calculated in tones on the basis of IS:1732. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing, shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (J.K./ Birla). (HSR 16.81)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (HSR 16.58)

Providing two coats of exterior acrylic emulsion paint. (HSR 16.79) (b)

Providing and Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.2). Through Rate

Providing and Applying Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.3). Through Rate

Providing and fixing sliding bolt with nuts and screws,etc.,complete(HSR 17.83 b i)

Providing and fixing 150 mm floor brass door stoppers, with rubber cushion, screws, etc., to suit shutter thickness complete.(HSR 17.75)

Supplying and fixing glass panes including pecial metal sash putty of approved make (b) glass panes 4 mm thick, exceeding 40 sq dm areas.(HSR 18.30)

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, lock notch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete: - (HSR 18.34 b)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge). INDIAN TYPE ORISSA OR ORYA WATER CLOSET SUITE for sinking into floor, with raised foot treads COMPLETE WITH 100 MM G.C.I.’P’ TRAP with or without vent as required and all OTHER NECESSARY FITTINGS as fully described in item no.30.1 above. (HSR 30.2 ai)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (as approved by the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT, SYPHONIC TYPE, consisting of- (HSR 30.5 a I white

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE size as give below ( to the proval of the Engineer- in-charge) including china plug for tap hole where necessary ;R.S. or C.I.BRACKETS for building into wall uding painting; 32mm C.P.BRASS WASTE WITHC.P. brass chain and rubber plug; 15mm .P.BRASS SCREW DOWN PILLAR TAP WITH jam nuts or couplings best design (as approved by the Engineer-in-charge) ALLFITTINGSBESTINDIAN MAKE and; to the approval of the Engineer-in-charge. ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and MAKING GOOD THE WALLS, FLOORS AND PAINTING OF FITTINGS ETC. (HSR 30.41 V)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE A RANGE OF TWO URINALS LARGE FLAT BACK OR ANGULAR LIPPED FRONT 610MM HIGH IN VITREOUS CHINAWARE WITH 5 LITRES CAPACITY BEST INDIAN MAKE C.I. AUTOMATIC FLUSHING CISTERN WITH FITTINGS AND FLUSH PIPE ETC.COMPLETE as fully described in item no.30.25 above.(HSR 30.26i)White

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE A RANGE OF THREE URINALS LARGE FLAT BACK OR ANGULAR LIPPED FRONT 610MM HIGH IN VITREOUS CHINAWARE WITH ONE NO. 10 LITRES CAPACITY BEST INDIAN MAKE C.I. AUTOMATIC FLUSHING CISTERN WITH FITTINGS AND FLUSH PIPE ETC.COMPLETE as fully described in item no.30.25 above.(HSR 30.27i) white

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge). (HSR 30.75) long body

Supply and erection of polypropylene random PP-R hot water pipe as per IS-15801 with elbow tee socket etc. recessed on surface including all labour and material (HSR 30.122) 16mm

Providing and fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS: 12701 on roof top of buildings includig cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respect to the satisfaction of Engineer-in-Charge.(HSR 30.119) 1000 Ltr

Providing & fixing PVC Rain Water Pipe 6 kg. pressure of ISI Mark in cement mortar during masonry work. (HSR 13.89)100mm

Earth work non plastic or Tibba Sand under floors taken from outside of campus area with all lead and lift including loading, unloading, laid in 15 cm layer including ramming, watering, consolidating, compaction, and compensation of earth etc., complete in all respect as per the direction of engineer in charge. [NS].

Recovery Items: Bidders have to quote rates for recovery items at least or more than reserve price. The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Note: - The reserve amount is minimum amount to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price as under:- The quantities are as under:- i) Credit of Good Bricks @ Rs. 4.50/- Each

ii) Credit of Brick Bats @ Rs. 400/- per cum

E.I. Works Moulded case Circuit breakers. HSR 31.12 (c) Supply and erection of moulded case circuit breakers on wall or on existing pedestal including bonding to earth and necessary connections. (i) 15 amp.to 60 amp. 415 V ,10 KA 3-phase.

Miniature Circuit Breaker and Isolator. (HSR 31.17) Supply and erection of miniature circuit breaker/ isolator 240/415 V in the existing distribution board including making necessary connection. (a) Miniature circuit breakers of 9 KA breaking capacity. (ii) SP MCB of 9 KA breaking capacity 6 amp. to 32 amp.

(ii) SPN MCB of 9 KA breaking capacity 6 amp. To 32 amp.

(iii) TPN MCB of 9 KA breaking capacity 40 amp. to 63 amp.

Supply and erection of Fittings and Accessories. (HSR 31.18) (vii) Call bell 220 / 230 volts A.C. bakelite with double coil.

(ix) (b) Bell push flush type ( without flexible wire ) in existing sheet.

(xi) Bakelite angle / straight button holder large size.

(xii) Switch 5 amp. On existing sheet

(xiii) Wall socket 5 amp. On existing sheet.

Pipe Laying. (HSR 31.21) Supply and erection of pipe for wiring purposes including bends inspection boxes etc. where necessary and painting as required. (xv) Heavy gauge welded conduit pipe 20 mm dia 1.60 mm thickness on surface.

(xvi) Heavy gauge welded conduit pipe 25 mm dia 1.60 mm thickness on surface.

Earthing (HSR 31.22) (i) Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. as required.

(ii) Extra for using salt and charcoal / coke for pipe earth electrode as required.

(xii) Pdg. and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required.

(xvi) Pdg. and fixing 4.00 mm dia G.I.wire on surface or in recess for loop earthing as required.

Supply and erection of under ground cable, loose in existing pipe or trenches complete with necessary connections. (HSR 31.26) (v) Ard. - 16 Sq. mm 2 Core Cable.

Supply and erection of suitable compression type brass cable glands for underground Cable. (HSR 31.28) (ii) 10 Sqmm to 16 Sqmm Cable 2 to 4 Core .

Street Light. (HSR 31.30) (IV) Supply and erection of weather proof M.S.Box of size 20 cm x 15 cm x 10 cm. covered with 3.00 mm thick M.S.sheet hinged cover, locking arrangemrnt , housed in wall , including the cost of 1 no. 16 amp. 415 volts kit-kat and 2 nos. 63 amp. 415 volts neutral links fixed on hard wood board in the M.S.Box including painting and necessary connections.

Wiring in existing conduit pipe(Recessed) for electrical points. (HSR 31.38) wiring only in 1.5 sq.mm PVC insulated copper conductor cable in existing conduit pipe and MS boxes covered with 5 mm thick bakelite sheet including cost of switch, wall socket, ceiling rose etc. (i) Fan Point b) Medium Point .

c) Long Point .

(ii) Light point a) Short Point

b) Medium Point .

c) Long Point .

vi) Call bell point c) Long point

(vii) 3 pin 5 amp. plug point including earthing the 3rd. pin etc. b) Medium point.

c) Long point.

(viii) 3 pin 15 amp. plug point including earthing the 3rd. pin etc. with 4 sq mm PVC insulated copper conductor cable. c) Long point.

Supply and erection of PVC unsheathed copper conductor cable single core 1100 volts grade in pipe of suitable size excluding cost and erection of pipe. (HSR 31.40) i) Cable size 1.5 sq.mm(3/ 0.81 mm)

iii) Cable size 4.0 sq.mm(7/ 0.85 mm)

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBs and ELCBs etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-charge of work. (HSR 31.41) i) 4 way SP&N (Horizontal)

vi) 8 way TP&N (Horizontal) (8 +24)

Supply & erection of Socket size rotary step type Electronic regulator for A.C. ceiling fan Anchor make Delux model No. 50440 ISI / SSK make PC 561 operated on 120/280 V A.C. Supply complete including cutting of existing Bakelite sheet and making necessary connection etc. up to the entire satisfaction of the Engineer-in-Charge of the Work. (HSR 31.55)

Supply and erection of Ceiling Fan 48'' complete in all respect upto the entire satisfaction of the Engineer -in-charge of the work make Bajaj/ Crompton/ Havells/ Orient. (NS)

Supply & erection of LED Batten 18W 1200MM long complete in all respect up entire satisfaction of Engineer In Charge of the the work. Make Bajaj/ Crompton/ Havells/ Jaquar/ Surya. (NS)

Supply & erection of LTEF 70W HPLED flood Street light with all accessories complete in all respect up to the entire satifaction of Engineer-in-charge of the work Make C&S/Jaquar/Havells/Surya/Crompton. (NS)

Supply & erection of MCCB Box suitable for 63 A to 100 amp MCCB complete with all accessories complete in all respect upto to the entire satisfaction of the Engineer-in Charge of the work. (NS)

The Shivam CoOp L and C Society Ltd