REPAIR TO CERTAIN BR WORK, ROOF REPAIRS, WELCOME MAINTENANCE, JOINERIES, PLUMBING, SANITARY FITMENTS, TILING, FLOORING, PLASTERING GUNITING TO BLDG INCL PETTY REPAIRS OF INTERNAL EM WORKS TO CERTAIN BLDG AT AF STN ARJANGARH UNDER AGE AF AYANAG

Amount

B/R Works Demolition of cement concrete (unreinforced) of any description including cast-in-situ terrazzo (below or above ground level), not exc. 15 cm thickness, including removal of rubbish outside MoD land, complete all as specified.

Demolition of cement concrete (unreinforced) of any description including cast-in-situ terrazzo (above ground level on first floor), not exc. 15 cm thickness, including removal of rubbish outside MoD land, complete all as specified.

Taking down cement plaster on brick walls or concrete surfaces & the like including raking out joints, hacking for key, scrubbing down with water etc., any description, including removal of rubbish outside MoD land, complete all as specified.

Demolition of brick masonry built in cement mortar as in drain etc., complete all as specified.

M & L for Brick work with sub class B bricks straight or curved on plan exceeding 6m mean radius, built in Cement Mortar (1:4) all as specified and directed.

All as per item No.05 above but except bricks. Note:- Serviceable bricks retrieved from Serial item No. 4 shall be used.

M&L for PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in coping, bed block, kneels, apex stones etc including weathering slightly rounded or chamfered including form work all as specified and directed.

M&L for Rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:4) finished even and smooth without using extra cement, complete all as specified.

M&L for Rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement, complete all as specified.

M&L for Rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces (such as top & sides of chajjas, beams, balcony ceiling etc.) finished even and smooth without using extra cement, complete all as specified and directed. Note: The rate quoted by contractor is deemed to be included necessary scaffolding and form work as required up to 3.50 Mtr high building.

M&L for PCC type B1, 1:2:4 (using 20mm graded stone aggregate) as in padding concrete to sunken floor, coving to juction of floor and vertical walls including chamfering on edges using WPC 2% by weight of cement. Note :-WPC will be measured and paid seprately.

Supply and fix, 40mm dia GI pipe, medium grade, as in spout for sunken floor, fixed as in wall, inside end fixed with wire netting & external bevelled edge at 45degree, complete all as specified and directed

M&L for Lean concrete (1:5:10), type E-2, using 40 mm brick coarse aggregate, as in sunken portion, complete all as specified and directed.

M&L for 25 mm thick, PCC (1:2:4), type B-0 (12.5mm graded crushed stone aggregate) as in flooring finished even & rough to receive the bedding mortar, complete all as specified.

Dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing)removing serviceable tiles to store and rubbish off the permises complete all as specified and as directed

S&F First quality, Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sq.m but not exceeding 0.11 Sq.m, laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified.

S&F First quality, Non skid ceramic coloured joint free tiles, 10 to 12 mm thick (square or rectangular) area of each tile exe 0.18 Sqm but n.exe 0.38 Sqm, laid in floors set and jointed with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified.

All as per item No 16 & 17 above but on vertical surfaces such as skirting fixed on and including 10mm thick rendering in cement mortar 1:4 as backing coat complete all as directed.

M & L for first quality coloured glazed ceramic tiles, fixed in pattern of different colour including border of size 300x 450 x 7mm thick as in vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles laid over and including 10 mm thick rendering in cement mortar (1:3), including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed. Note :- Pattern of the tiles will be decided by GE at the time of execution.

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2, using 40 mm graded mechanically crushed stone aggregates, laid in 1:20 slope as in plinth protection including making joints at 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/ 25 & two parts heated sand (by volume), surface finished even and smooth without using extra cement, complete all as specified.Note: The concrete shall be laid at a stretch not exceeding 3 metre in length and width of joint shall not be more than 12 mm.

M&L for PCC (1:4:8), type D-2, using 40 mm graded mechanically crushed stone aggregates as in foundations, filling, sub base and mass concrete, complete all as specified.

M&L for 18-20mm thick granite ( of any type) work (table rubbed and polished ) in cooking plateform, shelves and the like, over and including 15mm thick screed bed in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including taking out the old broken stone complete all as specified and directed.

Material and labour for 20-25mm thick machine cut kota stone slab as in flooring, steps of stair(treads), set with neat grey cement slurry @ 3Kg/Sqm, laid over and including 20mm thick cement and sand mortar (1:6) screed bed/bedding layer, jointed with grey cement slurry mixed with pigment to match the sahde of the slab including rubbing and polishing incl dismantling old stone slab of any description complete all as specified

Material and labour for machine cut kota stone slab 18-20mm thick as in skirting/dado, riser of steps, laid over and including 10mm thick backing coat in CM (1:4), set in neat grey cement slurry @ 3Kg/Sqm, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition), complete all as specified.

M&L for providing precast reinforcement cement concrete (1:2:4) type B-1 using 20mm graded aggregate in man holes covers slabs/ Shelves as in slabs supported on walls, beams and columns, in floors, roofs, landings, deck slabs and in shelves and like complete all as specified and directed.

M & L for Mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending etc., and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified.

Use & waste of form work to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work; with rough finished surfaces of concrete, complete all as specified.

S & f in repairs bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified.

S & F in repairs Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for 15mm bore iron pipe complete all as specified.

S & F in repairs angle cock/stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 15 mm bore iron pipe or for brass ferrule complete all as specified.

S & F in repairs stop valves, cast copper alloy, chromium plated, fancy type, with long shank and cup (concealed type), screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15mm bore iron pipe or for unions complete all as specified.

S&F in repairs 15mm dia gun metal gate valve, with iron wheel head, screwed both ends for iron pipes complete all as directed by Engr in Charge.

S&F in repairs 20mm dia gun metal gate valve, with iron wheel head, screwed both ends for iron pipes complete all as directed by Engr in Charge.

S&F in repairs PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Supply and fix in repair Vitreous China wash down water closet constellation premium Cat NO 20089(S-10) of Hindware white colour or approved equivalent as per specification complete set incl cistern with lid cover Hindware Cat Part No 21038 or approved equivalent as per specification, including connection to waste pipe, flushing pipe, anti-syphonage pipe etc. and making good to floor complete all as specified and directed.

Supply and fix in repair Vitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts flushing cistern and flush pipe), including connection to wate pipe, flushing pipe, anti-syphonage pipe etc. and making good to floor complete all as specified and directed

S&F Plastic water closet seat black/ white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging devices, connected to drains outlet, complete all as specified and directed.

S&F in repairs vitreous china squating pan, 'Orissa' pattern, size 580x440mm white, with integral foot rests, including 100mm cast iron 'P' or 'S' trap and 100mm cast iron sanitary connection socket to fit WC outlet including connection to trap, to flushing pipe, anti-syphonage pipe etc. complete including making good to floor complete all as specified and directed.

S & F in repairs 10 litres capacity, PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and suitable flush pipe PVC 32mm dia complete all as specified and directed.

Fixing only in repairs, low level flushing cistern of any description, complete all as specified and directed by Engineer-in-Charge.

S&F Chromium plated brass shower rose 125 mm sizewith or witout swivel joints including fxing with 15 mm bore pipe, fixed in repairs, complete all as specified.

S&L Towel rail 600 mm long, 20 mm dia, ‘D’ type, brass, chromium plated, fixed to walls with screws and plastic cleats, fixed in repairs, complete all as specified.

S&F in repairs Wash basins, vitreous china, white, flat back of size 550x400mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia waste fittings, brass, chromium plated with long screwed shanks and fly nuts, 32mm dia HDPE waste pipe and including new brackets complete all as specified and directed.

S & F in repairs, vitreous china wash basin, flat back or angle back and of any size including cutting for and pinning in ends of bracket fixing pillar tap and other fittings, complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections 15mm dia pipes including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down steel tubing and connections 20mm dia pipes including cleaning for refixing or removal to store complete all as specified and as directed.

S & F 15mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and directed. Note : Cutting chases as required shall be measured and paid seperately.

S & F 20mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and directed. Note : Cutting chases as required shall be measured and paid seperately.

Refixing old steel tubing and connections 15mm dia in new or old position (walls, ceiling, floors etc).

Refixing old steel tubing and connections 20mm dia in new or old position (walls, ceiling, floors etc).

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, including removal of rubbish outside MoD land complete all as specified.

Cutting holes into or through brick/ concrete walls built, in cement mortar, exceeding 150 Sqcm but not exceeding 400 Sqcm in superficial area and making good in cement mortar 1:3 to match with the existing finishes, complete all as specified.

Taking down cast iron soil, waste and vent pipes in any position (75/100mm dia), including cleaning for re-fixing complete all as specified and directed.

Material and labour for 75mm dia cast iron soil, waste and vent pipes (sand cast) in any length with or without ears, including cement jointing, fixed to wall with and including mild steel clamps and bolts with washers, complete all as specified and directed. Note : Extra over for lead joints shall be measured and paid separately.

Material and labour for 75mm dia cast iron soil, waste and vent pipes (sand cast) in any length with or without ears, including cement jointing, laid in trenches or in floors including necessary excavation and earth work, complete all as specified and directed. Note : Extra over for lead joints shall be measured and paid separately.

Material and labour for 100mm dia cast iron soil, waste and vent pipes (sand cast) in any length with or without ears, including cement jointing, fixed to wall with and including mild steel clamps and bolts with washers, complete all as specified and directed. Note : Extra over for lead joints shall be measured and paid separately.

Material and labour for 100mm dia cast iron soil, waste and vent pipes (sand cast) in any length with or without ears, including cement jointing, laid in trenches or in floors including necessary excavation and earth work, complete all as specified and directed. Note : Extra over for lead joints shall be measured and paid separately.

S & F in repairs cast iron bends 75mm bore, diminishing pieces or tapers ISI marked complete all as specified.

S & F in repairs cast iron bends 75mm bore, diminishing pieces or tapers fitted with oval access door ISI marked complete all as specified.

S & F in repairs cast iron bends (any radius) with duck's foot or heel rest 75mm bore, ISI marked complete all as specified.

S & F in repairs cast iron bends 100 mm bore, diminishing pieces or tapers ISI marked complete all as specified.

S & F in repairs cast iron bends 100mm bore, diminishing pieces or tapers fitted with oval access door ISI marked complete all as specified.

S & F in repairs cast iron bends (any radius) with duck's foot or heel rest 100mm bore, ISI marked complete all as specified.

S & F in repairs 75mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel brances with oval access doors complete all as specified and directed.

S & F in repairs 100mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel brances with oval access doors complete all as specified and directed.

S & F in repairs 75mm bore branch pieces, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel brances with oval access doors complete all as specified and directed.

S & F in repairs 100mm bore branch pieces, double(equal or unequal), ordinary or inverted (spigot or socket type) or with parallel brances with oval access doors complete all as specified and directed.

Materials and labour for extra over for lead joints provided in lieu of cement joints for 75mm dia cast iron pipes and fittings, complete all as specified and directed.

Materials and labour for extra over for lead joints provided in lieu of cement joints for 100mm dia cast iron pipes and fittings, complete all as specified and directed.

M & L for cast iron floor trap, 75 mm dia of out let, ISI marked, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), fixed in repairs, complete all as specified.

M & L for cast iron floor trap, 100 mm dia of out let, ISI marked, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), fixed in repairs, complete all as specified.

S & F in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified.

S & F in repairs 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified.

S & F in repairs 110mm bore PVC (SWR) bends any radius complete all as specified.

S & F in repairs 75 mm bore PVC (SWR) bends any radius complete all as specified.

S&F in repairs 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) Make Prayag, Polytuff

S&F 40mm dia cup board knob fixed with nut screw and washer of mild steel bright finish all as specified.

Cleaning and removing all scales and dirt etc by scraping with hard plastic/nylon wire brush and washed with bleaching powder solution and thereafter washed with clean water from service water tank and mouth of circulating pipe of capacity of tank exc. 250 litre but not exc. 500 litre including writing letters “Tank cleaned on_____ (date)” boldly with thick white/black synthetic enamel paint by using stencil with height & width of each letter & figures 150mm & 10mm respectively complete all as specified and as directed .

All as per Ser item No 80 above but capacity of tank exc.500 litre and not exc.1000litre.

Welding in repairs not exceeding 2.5cm in length (thickness of metal to be welded not exceeding 6mm) including cleaning preparing the surface and holding the members in true position for maintenance of steel items such as gates, grills, doors, windows etc., complete all as directed.

Taking down shutters of any description not exceeding 1 Sq. m each, from chowkhat, complete all as specified

Taking down shutters of any description exceeding 1 Sq. m but not exceeding 2 Sq. m each, from chowkhat, complete all as specified

Taking down Chowkhats with shutters without taking of shutter from the frame of any description not exceeding 1.50 Sq. m each, and making good the disturbed Surface in CM 1:4 & finished with similar specification as exists, complete all as specified

Taking down Chowkhats with shutters without taking of shutter from the frame of any description exceeding 1.50 Sq. m but not exceeding 4.00 Sq. m each, and making good the disturbed Surface in CM 1:4 & finished with similar specification as exists, complete all as specified

Resecuring or easing and adjusting without taking down shutter from the frame & re-fixing builders hardware as required including removal of unserviceable screws etc. not exceeding 1 Sq.m each, complete all as specified and directed by Engineer - in -Charge.

Resecuring or easing and adjusting without taking down shutter from the frame & re-fixing builders hardware as required including removal of unserviceable screws etc. area exc 1 Sq.m but not exc 2 Sq.m each, complete all as specified and directed by Engineer - in -Charge

S&F Pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with and including back filling with PCC (1:3:6), type C-0, complete as specified.

S&F Pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with and including back filling PCC (1:3:6), type C-0, complete as specified.

S&F 2nd class hard wood plain, solid, straight chowkats and frams wrought, framed rebated on solid, rounded or chamfered put together with glue pinned at joints complete all as directed.

S&F for 35 mm thick second class hard wood plain framed factory made panelled shutter (two panel) with lock rail and panel 9mm B.W.P or 12 mm veneered particle board with commercial veneering on both faces . The size of rail and style as per IS 1003/SSR part -1.

S & F 35mm thick 2nd class hard wood factory made Glazed and skelton shutters open rebated and prepared to receive glass, gauge etc edges of framing plain chamfered or rounded fitted with cut & mitred beads for securing glass etc size of members shutter as specified in SSR Part I Section 8, Clause 8.23 (a) supplied and fitted to chowkhats, 35mm thick 2nd class hard wood.

S&F Factory made flush shutters 35 mm thick, ISI marked, solid core construction, with block board core and plywood face panels, commercial type on both faces, complete all as specified

S&F Factory made PVC solid door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of 5 mm thick plain colour PVC sheet cut at corner and jointed with 02 Nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided throughout the frame and fixed to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos. of screws to be provided for each vertical member & minimum 02 Nos. for horizontal member), complete all as specified.

S&F Factory made moulded door shutter with particle board core, 28 to 30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick moulded prelam PVC sheet on the front face & 2 mm prelam PVC sheet on back face, complete all as per manufacturer instructions complete all as specified.

S&F Mild steel butt hinges medium weight, cold rolled, 100 mm, ISI marked, complete all as specified.

S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, 100 mm, ISI marked, complete all as specified.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete.

S&F 200 mm aluminium anodized, barrel tower bolts of extruded section.

Supply and fix 100mm size aluminum handle fabricated, 'D' type, anodized ISI marked complete all as specified and directed.

Supply and fix 150mm size aluminum handle fabricated, 'D' type, anodized ISI marked complete all as specified and directed.

S&F 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy complete.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy complete.

S&F 18 mm/ 19 mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice lamination for wooden and fixed with screws to timber frame as in cupboards, shutters, shelves, pelmet etc. including fixing 18 mm wide 6 mm thick beading of Ist class HW (Teak) all around, fixed in repairs, complete all as specified and directed.

Supply & fixing block board 18/19 mm thick, grade 2 quality, interior grade, commercial type fixed with screws to timber frame as in cupboards, shutters, shelves, pelmet etc. including fixing 18 mm wide 6 mm thick beading of Ist class HW (Teak) all around, fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

S & F plain fillets square, rectangular or triangular in section, 2nd class hardwood of sectional area exc 13 & n exc 25 sqcm, clean sawn, wrought finished secured with screws complete all as directed.

Continuous (piano) hinges, mild steel, bright finish or electro galvanised, 30 mm wide flap (when open), fixed in repairs, complete all as specified.

100 mm size hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, fixed in repairs, complete all as specified.

Supply and fixing, stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to steel frames with tinned tacks, or galvanized wire staples, or fixed to wooden frames with first class hard wood bead, complete all as specified and directed.

Supply and fix in repairs, stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to steel frames with tinned tacks, or galvanized wire staples, or fixed to wooden frames with first class hard wood bead, complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description) from wooden/ steel frames, glazed with putty or fixed with wooden beads/ metal pins complete all as specified and as directed.

S & F 3mm thick Sheet glass ordinary quality and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane, complete all as specified. Note:- New wooden required for glazing glass in wooden window will be paid for separately.

S & F 3mm thick figured glass, pin headed type and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane, complete all as specified.

Supply and fixing, drapery rod of mild steel 25mm dia, ribbed/fancy type, PVC powder coated, any shade, including set of fixing brackets, for span not exceeding 2m, fixed to wall in repairs, with PVC finols/finnels, connected accessaries, rubber packing, required screws and PVC rawal plugs as required complete all as specified and as directed.

Taking down old steel windows & S&F ECO-4000 Series windows/ventilators (Double rebate) fabricated from roll framed sections made of galvanized steel colour coated/powder coated ( Base steel as per IS 513"D" quality galvanized as per IS 277 with Zinc of 120gms/Sqr.mtr) with total coated thickness of 0.6mm and section of frame should be of 72mm x 55mm ,section for mullion should be of 72mm x 50mm, section for shutter frame should be of 47mm x 20mm, section for fixed glass bead should be of 12mm x 12mm and section for fly mesh should be of 40mm x 20mm, coated section should be with primer coat of Epoxy primer of 5-7 microns thick,finish painted with polyester paint of 12-16 microns thick or powder coated with pure polyester upto to 50-60 microns thick including 5mm thick plain glass, stainless steel 32 gauge fly mesh of 304 grades with 144 holes per square inch and Grill made of 10mm Sq MS bars welded to at 150mm centre to centre, 6mm x 12mm MS flat (total grill unit should be powder coated and fixed to window frame with screws).

Item No 116.00 contd.... (a) FIXING DETAILS :- Section for frame Glazed shutters and Mesh shutters should be cut to length and miter joined with polypropylene corner brackets,mullion section should be joined with Frame/Mullion using Mullion Cap ethyl propylene damein monomer (EPDM) gasket should be used all around glass in shutter and fixed glass,rubber Gasket should be used around glass in shutter and fixed glass.Rubber gasket should be used around fly mesh to fix mesh in mesh shutter. (b) ACCESSORIES :- Each glazed shutter and mesh shutter should be provided with SS pivot hinges - 1 set, seccolor handle & seccolor stay. Window frame should be fixed to brick/concrete masonry by using Nylon self expanding caps and driving MS electroplated 80mm long screws into the caps through frame. Make :- NCL alltek and seccolor Ltd and Eqivalent.

Taking down old steel /wooden windows & M&L for factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified.

Taking down old steel /wooden windows & M&L for factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified.

Taking down old steel /wooden vent & M&L for factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified.

Taking down old steel /wooden vent & M&L for factory made box type steel ventilator without glazing bars dovetailed or welded for fixing wire and with one shop coat of zinc chromate primer complete all as specified.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; and similar work conforming to Fe-290 Gde-E-165, complete all as specified.

Mild steel door spring 150 mm, ordinary rat tail rod pattern spring including roller and roller plate, fixed in repairs, complete all as specified.

Cutting holes in brick walls exceeding half brick but not exceeding one brick built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or PCC 1:2:4, including removal of rubbish outside MoD land, complete all as specified.

M&L for Rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete drilled for fixing of steel sheeting or other covering doors, etc to be prepred for hanging or sliding with and including either hooks and hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running, also fasting and fixing complete. Fe 290 (Gde E-165)

S&F 0.80 mm thick mild steel, plain, black sheet in hearths, covering to door shutter, covering to door chowkats ( frames), chullah hoods, water tanks,water trough, ducy, urinaltroughs and funnels etc. cut to size edges beded if directed holes punched including round headed screwes clout nails or rivets and fixed to wood or steel members, etc with plain 40mm lap joint or welded/ riveted seams including bending turning up mitred angle stopped ends outlet etc as required. continuous ( pino ) hinges mild steel bright finished or electroglvanised width of flaps ( when open ) in mm 30 complete all as specified and directed.

S&F in repairs Internal fitting (siphon) of flushing cistern tank for Vitreous China wash down water closet constellation complete as per sample available in sub division.

M&L for 2mm thick white wall putty on new/old surfaces of walls & making the surfaces fair and smooth complete all as specified and as directed by Engr-in-charge.

M&L for Three coats of white wash including preparation of new plastered wall surfaces of any description complete all as specified.

Material and labour for compiete of newly plastered surfaces as of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer to achieve uniform and smooth surface by roller brush having no sign of brush marks complete all as specified and directed. Make of oil bound distemper : Asian paints (Tractor)/ICI Dulux/Nerolac paints/Berger (Bison)

Material and labour for preparation of newly plastered surfaces as of ceiling surfaces and applying two coats of white lime wash to achieve uniform and smooth surface complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of cement base paint to achieve uniform and smooth surface having no sign of brush marks complete all as specified and directed. Make of Cement Base paint : SNOWCEM/ASIAN PAINTS/DUROCEM/BERGER

M&L for Preparation of new or previously untreated wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified.

M&L for preparation of new surfaces of steel and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified

Material and labour for preparation of old surfaces of walls by washing rubbing down and stopping of surface and applying one coats of cement base paint complete all as specified and directed. Make of Cement Base paint : SNOWCEM/ASIANAINTS/DUROCEM /BERGER

Material and labour for preparation of old painted surfaces of steel of any description and girth, not otherwise described and treated with one coat of synthetic enamel paint complete all as directed.Make of Paint : Asian(Apcolite)/ Nerolac (Goodlass)/ Berger paints/ICI Dulux

Material and labour for preparation of old painted surfaces of wood and wood based of any description and girth, not otherwise described and treated with one coat of synthetic enamel paint complete all as directed. Make of Paint : Asian(Apcolite)/ Nerolac (Goodlass)/ Berger paints/ICI Dulux

Material and labour for preparation of old plastered surfaces of walls by washing, rubbing down and stopping of surface and applying two coat of white lime wash complete all as specified.

Material and labour for preparation of old plastered surfaces of ceiling by washing, rubbing down and stopping of surface and applying two coats of white wash complete all as specified and directed.

Preparation of old surfaces of walls including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc.; rubbing down and stopping of surfaces using sand paper and applying one coat of oil bound distemper, complete all as specified and directed by the Engineer-in-Charge.

Material and labour for preparation of new decorated surface of walls including applying cement based wall care putty (Birla care/JK wall putty) 1mm thick(average) and applying two coats of exterior emulsion (any colour) paint over a coat of primer of same manufacturer to achieve uniform and smooth surface using roller brush complete all as per manufactures instructions and directed. Make of exterior emulsion paint : Asian (Apex ultima)/ Berger (Weather coat)/Nerolac (Excel total)

Material and labour for preparation of old decorated surface of walls and applying one coat of exterior emulsion (colour matching with existing) paint by roller brush of approved manufacturer complete all as per manufactures instruction and directed.

Material and labour for complete removal of existing treatment old decorated surface of walls and applying cement based wall care putty (Birla care/JK wall putty)1mm thick(average) and applying two coats of plastic emulsion (any colour) paint to achieve uniform and smooth surface by roller brush over a coat of primer of same manufacturer complete all as per manufactures instruction and directed. Note:-Payment will be made for two coats only.

Material and labour for removal of existing treatment completely on walls and preparaing the surface for applying two coats of oil bound distemper to achieve uniform and smooth surface by roller brush over and including cement based wall care putty 1mm thick(average thickness) complete all as specified and directed.

M&L for Providing and injecting chemical emulsion for Post Constructional antitermite treatment along external wall where the apron is not provided along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as spd and directed.

M&L for Providing and injecting chemical emulsion for Post Constructional antitermite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as spd and directed.

M&L for Providing and injecting chemical emulsion for Post Constructional antitermite treatment At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as spd and directed.

Dismantling boarding any description (board/plywood) fixed in any position with screw, complete all as specified

S&F 6mm thick plywood with 5Nos of ply, grade BWR, type BB, fixed with screws to timber frame work etc, complete all as specified. (Make : Kitply, Green ply,Bhutan Board)

M&L for 18/19mm thick MDF board, exterior grade, prelaminated both sides with decorative choice laminationwith BWR type adhesive, fixed with screws to timber frame work as in cup board shutter, loft shutters incl 6 mm thick teak wood lipping and necessary rebating for leaf shutters where required including polishing to lipping/rebating complete all as specified.Make : Kitply/Novapan/Butan Board/Greenply.

S & F in repair Plastic water closet seat cover, any colour, closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device. Make : Cera 1st quality/Parryware/HSIL.

Supply and fix in repairs chromium plated brass central hole WHB mixer 15 mm bore chromium plated, fancy type including joints to hot and cold complete all as specified and directed.

Supply and fix in repairs CP brass health faucet of 15mm bore pipe with 1.5 mtr. Flexible pipe screwed for iron pipe fancy type long body complete all as specified and directed.

S&F in repairs 32/40mm bore and 75cm long PVC waste pipe for WHB/Sink complete all as specified.

S&F Rotational moulded polyethylene water storage tank 500 litres capacity, ISI marked triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for 20mm bore GI pipe of having weight not less than 210gms including all fittings and gate valves with iron wheel head 20mm size, including taking down existing tank complete all as specified and as directed.

S&F Rotational moulded polyethylene water storage tank 1000 litres capacity, ISI marked triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for 20mm bore GI pipe of having weight not less than 210gms, including all fittings and 20mm size gate valves with iron wheel head including taking down existing tank complete all as specified and as directed.

Roughneing surfaces of old concrete floors by picking remove dust etc including brushing neat cement slurry with 3.0 kg of cement per sqm. complete all as specified.

Cutting out cracks to V section in existing roof or terracing cleaning out, wetting grouting with cement and sand slurry 1:3 complete all as specified.

M & L for avg 25 mm thick PCC (1:2:4) type B0 as in flooring and other similar works (using 12.50mm grades stone aggregate) for filling of depressions in roofs slab or mainting the proper slope to roof, complete all as specified.

Material and labour 15 mm thick cement plaster in CM (1:4) mixed with WPC as per manufacturer’s instructions @ 150 ml by per bag of cement on concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid separately.

Applying evenly a tack coat of insustrial bitumen 85/25 @ 1.2Kg /Sqm including cleaning surface.

Supply only liquid water proofing compound.

S&F PVC tank lid (cover) suitable for 500/1000 litres capacity water tank with hinged and hooked fixing by steel screw for existing PVC water tank on buildings, fixed in repair, complete all as directed by Engineer -in-Charge.

Material and labour for preparation of old surfaces of walls and Writing the name of the officer and rank in front of the married residence with sky blue and white colour acrylic enamel paint complete all as specified and directed by engineer in charge. Note : 01 officer's Name and Rank will be counted as Each Job.

M & L for 40mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregates as in flooring finished even & smooth without using extra cement, complete all as specified.

S& F in repairGrating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), complete all as specified.

S& F in repair Grating doom 125 mm dia with waste hole of PTMT, complete all as specified.

S&F power coated aluminium frame work for doors, windows,partition s etc incl grill for windows for windows etc with one or more rebated section incl jointing cleats for fixing etc complete complete.

S&F powwer coated anodised aluminium door shutters, partition wall, aluminium section weighting 0.55 Kg/Rm incl necessary joining cleats glazing clips rubber neoprene packing, handles two Nos in each door, hinges anodised aluminium snap beading screws etc complete all as specified and as directed.

S&F powder coated anodised aluminium window and ventilator shutters , side hung type without sash bars aluminium section weighting 0.55 Kg/Rm incl necessary joining cleats glazing clips rubber packing, aluminium anodised snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (1Nos0, hinges type B-21 100 mm long(2Nos) suitable handles (1Nos)complete all as specified and as directed.

S&F 12 mm thick prelaminated board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to aluminium frame work complete.all as specified and directed by Engineer - in - Charge .

S&F double action floor spring hydraulic regulated made up of min 1.25 mm thick aluminium sheet foundation box, main body with stainless steel cover, govering pivets made of brass, other part made up of mild steel heavy duty complete. all as specified and directed by Engineer - in - Charge .

S&F brass six lever pad lock suitable for aluminium doors manufactured by Harrison Locks or Godrej as approved

S& F in Repairs Stainless steel Kitchen Plate Rack of size 31" x 36" x 10" of 1 mm thick stainless steel sheet with all internal fittings, and fixed to wall by means of rawl plug steel screws including washer complete all as specified and directed by Engr-in-Charge.all as specified. . Make : Nirali/Jayna/ Diamond

E/M Works Taking down carefully copper / aluminium point wiring (light, fan, switch, socket or power, Bell & Two way point) complete with fitting such as switches, sockets, ceiling rose, sketch light fittings etc, and making good the disturbed surface of walls and floors etc as directed.

Taking down carefully copper / aluminium sub main wiring including teak wood batten / conduit and making good the disturbed surface of walls as directed.

M & L for Point wiring with PVC insulated PVC unsheathed electric FRLS cable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good disturbed surface of wall (cutting except on ceiling for fan point only, on ceiling instead of pvc conduit surface casing capping will be used) & 1.5 sqmm green PVC insulated unsheathed copper conductor as a earth wire connected to earth dolly by providing lugs including MS boxes for mounting switches, sockets, fan regulators etc for the following :-

One light point controlled by one switch

One bell point controlled by one bell Push

One fan point controlled by one switch

One 5amps socket out let point controlled by one switch on same board with other switches.

One 5amps socket out let point on independent board controlled by one switch.

One light point controlled by two way switches

All as per item no-177 here in before but using pvc insulated unsheathed 2.5 sqmm cross sectional area cable for phase /neutral & for earth 1.5 Sq mm green PVC insulated cable for 15 amps socket point on independent board controlled by one switch.

M & L for Point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core having multistranded copper conductor of 1.5 Sqmm nominal cross sectional area drawn in and including non metallic rigid PVC casing capping not less than 25mm base size with all fitting and fixing accessories and with 1.5 Sqmm green PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor connected to earth dolly by providing suitable lugs including MS boxes for mounting switches. sockets etc complete for the following:-

One light / fan point controlled by one switch.

One bell point controlled by one bell Push

One 5 Amps socket outlet point controlled by one switch on same board with other switches.

One 5Amps socket outlet point controlled by one switch on independent board.

One light point controlled by two way switches

All as per item No. 179 but with 2.5 Sqmm cross sectional area electric cable for 15 Amps socket outlet point controlled by one switch on independent board complete.

M & L for Point wiring with PVC insulated unsheathed electric cable 1100 volts grade, single core, having multistranded copper conductor of 1.5 Sqmm nominal cross sectional area drawn in existing concealed conduit with 1.5 Sqmm green PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor connected to earth dolly by providing suitable lugs complete including MS boxes for mounting switches. sockets etc complete for the following :-

One light / fan point controlled by one switch.

One bell point controlled by one bell Push

One 5 Amps socket out let point controlled by one switch on independent board.

All as per item No. 181 but with 2.5 Sqmm nominal cross sectional area electric cable for 15 Amps socket outlet point controlled by one switch on independent board complete.

Supply and fix with switch piano flush button single pole one way 5 amps, 230 Volts complete as directed.

Ditto but 5 Amps, 2 way complete as directed.

Supply and fix with socket outlet flush type 5 Amps, 5 pin, 230 Volts complete as directed.

S&F with switch piano flush button single pole one way 15 Amp 240 volt complete as directed.

S&F with socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 230 volts complete as directed.

Supply and fix with bell push single pole, 6 amps, 230 Volts, flush type complete as directed.

supply and fix Ceiling rose surface Bakelite 63.5mm dia three terminal complete.

supply and fix Lamp holder, insulated body with back plate suitable for batten/angular fittings fixed complete make

Supply & fixing for electronic Fan regulator 450 watt .

supply and fix Bell,AC, 230 Volts, single pole fixed complete.

supply and fix Bell multi music type AC, 230 Volts, single pole fixed complete.

Supply and fix in repair white finished single mounting modular plates with inner & outer cover suitable for housing modular accessories of following sizes:

Suitable for one module . Make: Crabtree / Legrand or equivalent Make .

Suitable for 2 modules . Make: Crabtree / Legrand or equivalent Make .

Suitable for 3 modules . Make: Crabtree / Legrand or equivalent Make .

Suitable for 4 modules . Make: Crabtree / Legrand or equivalent Make .

Suitable for 6 modules . Make: Crabtree / Legrand or equivalent Make .

Suitable for 8 horizontal modules . Make: Crabtree / Legrand or equivalent Make .

Supply and fix in repair modular Switch 6 Amps single pole, one way complete . Make: Crabtree / Legrand or equivalent Make .

Supply and fix in repair Modular Socket outlet, multi purpose, 5 Pin 6 Amps flush type complete . Make: Crabtree / Legrand or equivalent Make .

Supply and fix in repair Modular Bell push flush type,6 Amps fixed complete . Make: Crabtree / Legrand or equivalent Make .

Supply and fix in repair Modular Socket outlet, multi purpose, 6 pin 16 Amps universal socket complete . Make: Crabtree / Legrand or equivalent Make .

Supply and fix in repair Modular Switch 16 Amps single pole, one way complete . Make: Crabtree / Legrand or equivalent Make .

Supply and fix in repair modular Switch 6 Amps single pole, two way complete . Make: Crabtree / Legrand or equivalent Make .

Supply and fix in repair modular fan regulator of four step type complete . Make: Crabtree / Legrand or equivalent Make .

Supply and fix in repair switch socket combination 2 in 1 , 3 pin , 5 and 15 amps flush type 230 volts complete as directed.

All as per item no 202 but 3 pin 5 amps

S & F in repair PVC rectangular block for mounting switches, sockets , fan regulator etc with 3 mm thick plastic laminated sheet cover of following sizes:-

350 x 300 x 50 mm size

250 x 200 x 50 mm size

200 x 150 x 50 mm size

175 x 100 x 50 mm size

100 x 100 x 50 mm size

S & F in repair plastic laminated Bakelite sheet cover of Hylam brand 2.8 mm thick including cutting holes for switches, sockets etc as pre requirement including fixing with machine screws and washer complete of following sizes:-

10" x 12" size

8" x 10" size

8" x 6" size

7" x 4" size

4" x 4" size

Supply and Fix in repair flush mounting factory made VTPN DB's ,IP-43 Protection -IK 09 with metal double door with 200 Amps copper bus bar with 2 neutral bar ,earth bar and cables ties for cable management fully insulated bus bar with set of wires and door earthing with provision of space for 100 amps MCCB as incomer and SP/TP MCB;s as out going 4 way complete. Make - HPL/ Indo Asian/ABB.

Supply and fix in repair double door TPN DBs four way of powder coated DB's suitable for MCB's fitted with bus bar, Neutral link, Earth bar and Din rail & DB's will be fitted concealed in wall / surface as per site required complete all as specified and directed . Make - Legrand / Hegar / L & T .

Supply and fix in repair double door SPN DBs eight way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din rail complete . Make - Legrand / Hegar / L & T .

Supply and fix in repair double door SPN DBs four way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din rail complete . Make - Legrand / Hegar / L & T .

S & F in repair with MCB SPN 5 to 40 amps 10 KA ,c-series including connection with suitable size aluminium / copper lugs complete all as specified and directed . Make - Legrand / Hegar / L & T .

S & F in repair with MCB SPN 50 to 63 amps 10 KA ,c-series including connection with suitable size aluminium / copper lugs complete all as specified and directed . Make - Legrand / Hegar / L & T .

S&F in repair with MCB SP 240 volts 5 to 40 Amps, 10 KA breaking capacity, 'c' type including connection with suitable size aluminium / copper lugs complete all as specified and directed . Make - Legrand / Hegar / L & T .

S & F in repair with MCB TPN 32 amps 10 KA ,c-series including connection with suitable size aluminium / copper lugs complete all as specified and directed . Make - Legrand / Hegar / L & T .

S & F in repair with MCB TPN 50 to 63 amps 10 KA ,c-series including connection with suitable size aluminium / copper lugs complete all as specified and directed . Make - Legrand / Hegar / L & T .

Supply and fix in repair MCCB TPN 415 volts, current rating 160 Amps having rupturing capacity 36 KA with Adjustable thermal setting ( 80 to 100 %) complete. Make - Havells /Merlin Gerin/HPL.

Supply & fix in repair Sheet metal earth plug, socket, single pole and neutral with single pole MCB 10 Amps 240 volts fixed in repairs complete.

Supply & fix in repair Sheet metal earth plug, socket, single pole and neutral with single pole MCB 32 Amps 240 volts fixed in repairs complete.

Supply and fixing in repair Wall light fixture lantern made up of polycarbonate ; suitable for 9 watt retrofit LED lamp ,spiral B-22 base including 9 watt LED and connection with all necessary accessories complete all as specified and directed. MAKE:- Havels Cat No.LHDLO2160099 or Eqvt. Bajaj/Philips.

S&F in repair LED luminaires of surface / wall mounted batten with polycarbonate housing and integrated electronic driver of 20 watt including 20 watt LED lamp and connecting with copper flexible three core 23/0.0076 and all necessary fixing accessories compleate. Make - Havells , Cat no - LHEXBxpnin1w020 or eqvt type of CG / Philips Bajaj .

S&F in repair LED luminaires of surface / wall mounted batten with polycarbonate housing and integrated electronic driver of 10 watt including 10 watt LED lamp and connecting with copper flexible three core 23/0.0076 and all necessary fixing accessories compleate. Make - Havells , Cat no - LHEXACP5IN1W010 or eqvt type of CG / Philips / Bajaj .

S & F in repair plasic body air fan / ventilator with louver 250mm sweep and grouting with nut , bolts & Fastenar on the wall and make good the disturbed surface and electric connection with 1.5 Sqmm three core PVC insulated round flexible copper conductor and sheathed cable complete all as specified and directed by Engr-In - Charge. Make:Havells or equivalent Make of CG / Bajaj.

S & F in repair Wall fan of single phase 230/240 V of size 400 mm sweep and grouting with nut , bolts & Fastenar on the wall and make good the disturbed surface and electric connection with 1.5 Sqmm three core PVC insulated round flexible copper conductor and sheathed cable complete all as specified and directed by Engr-In - Charge. Make:Havells or equivalent Make of CG / Bajaj.

M&L for Sub main wiring two single core PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn in but excluding non metallic rigid PVC conduit including PVC insulated unsheathed 4 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly complete.

All as per item No 223 but with two single core 4 Sqmm size cable complete including 2.5 sqmm multistranded copper conductor PVC insulated unseathed as continuous earth wire

M&L for Rigid non metallic PVC conduit ISI marked, medium grade, inclusive of all fitting such as tees,bends. Junction boxes, elbows saddles. Pipe hooks,couples and lock outs etc 25mm external dia, fixed on surface mounted complete and making good disturbed surfaces all as directed.

Ish Engineers and Contractors

JAIPAL AND BROTHERS

s r enterprises

M/S Rohit Enterprises

PAWAN KUMAR

M/S Sanjay Enterprises

akhil enterprises