SPECIAL REPAIR TO BR NATURE OF WORK NEAR CANARA BANK BUILDING NO P 370 AND CERTAIN EM WORKS UNDER GE I GOS

Amount

M&L for Repair to pot holes any depth, not exc 1 sqm each including sweeping free from dust and mud or water, scoring sunken surfaces in roads, paths, etc cutting around edges to at least 25mm in depth, and making good by applying tack coat @ 5 Kgs per 10 Sqm and laying premixed bituminious macadam well rammed and sealed with paving bitumen 60/70 or VG-30 grade@ 9.8 Kgs per 10 Sqm, blinded with 0.09 Cum of stone chipping of size 6.3mm and again well rolled with 8 to 10 tonne power roller (Iincluding supply of pre-mixed macadam, binder and chipping) depth of pot holes exc 30mm complete all as specified and directed by Engineer-in-Charge.

M&L for Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area not exc 400 sqm & depth exc 50 mm & n exc 100 mm. Complete all as specified and directed by Engineer-in-Charge.

M&L for 150 mm thick water bound macadam in two layers of 75 mm each (compacted thickness), with coarse aggregate of stone (granite / trap/ basalt) of grading 2 (63 mm to 40 mm size) or of grading 3 (50 mm to 20 mm size), spread, rolled and consolidated to required gradient and camber required. Complete all as specified & directed.

M&L for preparing un-surfaced water bound macadam by brushing with wire brushes for removing caked mud etc sweeping with brooms & finally fanning the cleaned surface with gunny bags to remove all loose dirt etc, providing evenly a tack coat of bitumen at the rate 10 kg per ten Sqm & providing Bituminous premix semi-dense asphaltic concrete 40 mm consolidated thickness with 5.50% binder content by weight of total mix, rolled & compacted to required camber & gradient complete. (Mix shall be obtained from HOT MIX PLANT and spreading shall be done with MECHANICAL PAVER). Complete all as specified & directed.

M&L for Preparing existing black top surface or bituminous macadam surfaces by brushing with brushes for removing caked mud etc sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc on back top/concrete surfaces than applying evenly priming tack coat with paving bitumen 60/70 or VG-30 penetration over the prepared surface by mechanical sprayer @ 5 Kgs/10 Sqm of surface area complete all as specified and directed by the Engineer -in-Charge.

M&L for applying bituminous premixed semi dense asphaltic concrete 40mm thick (consolidated thickness) with 5.5% binder content of paving bitumen 60/70 or VG-30 grade by weight of total mix including cement filler, on surfaces rolled & compacted with using 8 to 10 tonne capacity power roller to achieve the required compactness, camber and gradient mixed in hot mix plant using design mix and laid by mechanical paver finisher. Complete all as specified and directed by the Engineer-in-charge.

M&L for premixed bituminous macadam laid, rolled and compacted to required gradient and camber n.exc 75mm thickness (consolidated thickness) with 4% binder content of VG -30 by weight of total mix, mixed in hot mix plant and laid by mechnical paver finished complete.

M&L for preparation of existing bituminous surfaces, removing, dust, dirt grease and other foreign matters etc to receive the marking and M&L for thermo plastic (Reflective) line marking having 1.0 mm thickness (average) of uniform surface finish conforming to BS 3262 (Part 1) 1989 read in conjunction with the MOST specification 803 clause 4.2.2 on bituminous surfaces in white/yelow clour and super imposed with glass beads confirming to BS 6088 read in conjuction with and MOST specification 803 clause 4.3.3 complete all as specified and directed. Note - MOST specification 803 shall be followed strictly for execution of work & suitable machine shall be used for the marking as approved by the GE. Shape & size/ patterns of marking shall be as approved by the GE.

S&F in repair cat eyes/road studs for roadways sign permanent surface mounted type having tough poly carbonate micro replicated corner cube reflector lenses with a protective abrssion resistant ceramor coating having body of weather proof and impect resistant thermoplasit complete as per manufacturer,s instruction and as directed. (Colour :- Yellow/Red/Amber) Make: Series 290 of 3M or Road Star or Equivalent.

S&F in repair solar cat eyes/road studs size (mm) 125L x 125B x 25H including stem height 53mm approx housing dia cast aluminium (grade LM-6) fully water proof and weather proof and weatherproof coating visible distance upto 400mtr LED-6 super bright amber led (3 Nos each side) yellow charged, flush frequency 1.2 Hz-1.8Hz including solar panel 3.5V/110MA & battery one PC sub ‘C’ type Ni-Cd rechargeable battery 1.2V/2.5AH temp range 20C to 70C fixed on road for roadway sign complete as per manufacturer’s instruction and directed by Engr-in-Charge Make- 3M/Avery Dennision/Dark Eye/Green/Greenlite/Road Star Cat Part No. GSR-909 or Equivalent.

S&F in repair plastic speed bumbs (Speed breakers) not less 400 mm wide blocks & yellow colours fixed with necessary spikes/screws to the road surface etc. Complete all as specified & directed by Engr -in - Charge.

S&F in repair ABS Body, 100 cm outdoor convex mirror good quality as approved by GE fixed in road/ground portion complete including hanging/fixing arrangement with adequate mounting arrangement at suitable height, having unbreakable Polycarbonate Convex Lens with hoods as the traffic safety mirror for eliminating blind spots & increase visibility at a broader angle, including excavation for post holes, PCC Type C-2 1:3:6 (using 40 mm graded stone aggregate) in post hole & removal of surplus excavated material to a distance not exceeding 50 metre & depositing where directed at a level not exceeding 1.5 metre above the starting point. Complete all as specified & directed. Make: Frontier 100 cm outdoor Convex Mirror, FMCO-100, Road Star, Real reflectors, Alexix, ACE polymers (India) or Equivalent.

S&F in repair high intensity prismatic retro - reflective (3m/Avery) sheet of colour as directed, self adhesive, fixed on steel/concrete surface etc all as specified and directed.

M&L 150 mm Soling (or sub base) with broken boulders or quarried stone, inter stices filled, surface formed and rolled and consolidated to required gradient and camber with 8-10 tones power roller complete all as directed

Demolition of Cement Concrete (unreinforced) of any description & in any position not otherwise specifically provided for. Complete all as specified & directed.

M&L for Excavating in trenches in soft/ loose soil, not exceeding 1.5m wide and not exceeding 1.5 m in depth for foundation, n exc 10 sqm in plan and getting out complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling, subbase & mass concrete. Complete all as specified & directed.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in sub base flooring average 25 mm thick surface finished even and rough (as in levelling course) to receive the topping layer complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off premises complete all as specified and directed

M&L for Sand filling under floors or in foundations including watering and consolidation

S&F machine pressed precast concrete interlocking paver block any shape & size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement & pigment. Complete all as specified & directed.

Supply, install, commissioning and testing of HVLS( High volume low speed) fan PMSM advanced technology without gearbox-Generation-3, sweep 7.3 mtr(24 ft),Air volume 13000 m³/min,6 blades,55 rpm,1.1kw, 3 Phase,50Hz,415 Volts,≤38 dB,motor weight 40 kgs,fan weight 107kgs,effective area 700 m³,covered area 1500m³ and including providing IP-54 controller for on/off, necessary fixing aceessories & all connected items, T&P such as boom lift scaffolding qpts,necessary SWR rope for anchoring /safety items and fan having the following accessories:- (a) Aviation aluminium alloy (AA6063T6511) PROFILI V2 blades-06 Nos,3 mm thickness.(b)Marut Air IP67,PMSM direct drive motor,'H' class insulation,68 poles,343.8N.M max torque super silent < 38 dB only.(c) Marut G3 motor have aerospace tech,maintenance free motor havingh Air + Liquid cooled technology.(d) Power 1.1 KW,55RPM.(e) IP-54 Controller.(f) Voltage 415 Volts.Complete all as specified and directed.Make :- Marut Air Model No.MTR-7a-G3

M/s J. P. ASSOCIATES (BID ID -3144007)

M/s M M Engineering Systems (BID ID -3144511)

ABC CONSTRUCTION COMPANY (BID ID -3144343)

M/s Ats Electricals (BID ID -3143617)

M/S SIWALIK AND CO (BID ID -3143764)

DHABALESWAR ENGINEERING WORKS (BID ID -3143769)