SPL REPAIR TO BLDG NO P/8/509, SUB STATION BLDG AT MAIN GATE FAD FASF, WALL AND GATE AT GE PANAGARH PREMISES AND OTHER PROVN WORKS AT PMS IN THE AREA OF AGE B/R-II UNDER GE PANAGARH

Amount

M&L for fly ash brick old size straight or curved on plan exc 6 mtr mean radius built in cement mortar (1:6) complete all as specified and directed.

Demolition of cement concrete as in ground floors and pavings not exceeding 15 cm thick below or above ground level (unreinforced) and disposal of rubbish to distence not exceeding 100 mtr complete all as specified and directed.

M&L for cement concrete 1:3:6, Type C-2 (Using 40 mm graded stone aggregates) in foundations etc complete all as specified and directed.

M&L for precast reinforced cement concrete 1:1.5:3 type A1 (using 20mm graded stone aggregate) as in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, mangers, shelves and similar articles with plain faces and set in cement mortar (1:6) (reinforcement measured and paid seperatly) including demolition of existing slab and disposal of rubbish to distence not exceeding 100 mtr complete all as specifed and directed.

M&L for 50mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in floor complete all as specified and directed.

M& L for 75mm thick PCC 1:3:6 type C-1 (Using 20mm graded crushed stone aggregate) as in plinth protection finished even and smooth without using extra cement, incl making joints 10mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with and incl bitumen and sand 1:3 by weight complete all as specified and directed.

M&L for designer coloured endura tiles 30cm x 30cm x 10mm thick, set jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L for light shade Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry pointed in white or coloured cement to match incl 15 mm thick screed bed or bedding layers of cement mortar (1:4) for laying of floor finishes complete all as specified and directed.

M&L for non-skid colour ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06 Sqm but n.exc. 0.11 Sqm in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match incl 15 mm thick screed bed or bedding layers of cement mortar (1:4) for laying of floor finishes complete all as specified and directed.

M&L for coloured glazed tiles in vertical surfaces 350x250x7-8 mm/450x350x7-8mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10 mm thick plaster as in bedding layers of cement mortar (1:4) on vertical surfaces.complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based semi /full corrugated steel sheet 0.5mm of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of sheet complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in Ridges fixed with self tapping screws complete all as specified and directed.

S&F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc including dismantling of sheet complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for in any position complete all as specified and directed.

S&F mild Steel work in tubular trusses, post and purlins etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.11611979 grade St.-240 complete all as specified and directed.

M&L for preparation of new or previousaly untreated surface steel surfaces of any description over 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for framed work such as grills, grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-410-O or Fe-310-O, complete all as specified and directed.

Taking down cement plaster from brick walls or concrete surfaces including raking out joints, hacking out for key, scrubbing down with water complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces finished even and fair on walls in cement mortar (1:4) complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar (1:6) complete all as specified and directed.

Extra for forming fair finished drain or channel upto 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc complete all as specified and directed.

M&L for two coats of oil bound destemper on new wall surface including chalk whiting, preparation to distempering applying 1.5mm thick (minimum) wall care putty on wall surfaces complete all as specified and directed.

M&L for complete removal of existing treatment including preparation of plastered surfaces of old wall of any description and applying two coats of OBD over a coat of alkali rsesistant primer over a coat of 1.5mm thick (minimum) wall care putty on old surface complete all as directed, by means of mechanical scrubber and manually where the mechane can not reach complete all as specified and directed.

Complete removal of exting treatment from ceiling and applying three coats of white wash on walls complete all as specified and directed.

Taking down window chowkhats or frame not exceeding 1.5 Sq. m each with shutter(s) (without taking off shutters from the frame), including removing to site complete all as specified and directed.

Taking down chowkhats or frame exceeding 1.5 Sq. m but not exceeding 4 Sq. m each with shutter(s) (without taking off shutters from the frame), including removing to site complete all as specified and directed.

S&F 2nd class hard wood (sal) plain solid straight chowkhat and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joint complete all as specified and directed.

S&F factory made UPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead /double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of UPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of UPVC extruded glazing beads and UPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (incl duing Glass or wiremesh) (Note: For UPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made)

S&F factory made UPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) including glass and wire mesh comprising of UPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), UPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Note: Glass shall be paid separately).

S&F Factory made, 35 mm thick, panelled shutter second class hard wood, plain framed, hammer marked, (two panel ) with lock rail . The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 2nd class hard wood 35mm thick Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc(without sash bars) edges of framing plain, chamfered or rounded, fittted with cut and mitred beads for securing gauge,etc sizes of member of shutter as specified SSR part-I Section 8 clause 8.24 (a) complete all as specified and directed.

S&F Solid PVC Door Frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specified and directed.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description , not otherwised described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150 mm long aluminium anodised handle cast type and fixed complete all as specified and directed.

S&F butt hinges, medium weight, cold rolled, mild steel, 100 mm long with welding to frame supplied and fixed complete all as specified and directed.

S&F 300mm aluminium anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixinf bolt and sliding bolts of extruded section or cast alumnium alloy and fixed complete all as specified and directed.

S&F sink with drainage board made of stainless steel thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm incl waste pipe 32mm dia complete all as specified and directed.

S &F in repair vitreous china squatting pan log pattern 580 mm long including foot rest, S or P trpa including lime concrete bedding complete all as specified and directed.

S&F PVC connection 15 mm dia, 450 mm long including check nut complete all as specified.

S&F in repair stop valve 15 mm dia cast copper alloy high pressure with crutch or butter fly handle screwd for iron pipe or union and fixed. Chromium plated fancy type complete all as specified and directed.

S&F in repair Towel rail Tubular towel rail 20mm dia 60cm long brass chromium plated complete all as specified and directed.

S&F Waste coupling of PTMT, for WHB any colour half or full threaded suitable for 32 mm size discharge pipe (Minimum weight 45 gm) complete all as specified.

S&F in repair PTMT shelf 450 mm x 124 mm any colour with brass chromium plated screws & PVC rawl plugs (Minimum weight 300 gm) complete all as specified.

S&F pillar taps 15 mm bore dia fancy type cast copper alloy with capstan heads, chromium plated, fancy type screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwd shank and fly nut screwd for iron pipes, fancy type complete all as specified and directed.

S&f vitreous china wash basin, white , flat back , size 550 x400mm (for hospital use) excluding taps, waste, chain and plug and porcelain stopper but including brackets any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S&F as in repair grating square 150mm size of PTMT(minimum 100 gms) complete all as specified and directed.

S&F GI tubing 15 mm bore medium grade with all fittings and fixed to wall complete all as specified and directed.

S&F as in repair 75mm PVC (SWR) floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F PVC bends plain (any radius) for 110mm bore PVC pipes complete all as specified and directed.

S&F Viterous China urinals, bowl type (back or corner wall type), of size 465 x 355 x 265mm white complete including providing and fixing plugs, bedding urinal agianst wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed. (Note: Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

M&L for 25mm thick PCC 1:2:4 type B-0 (using 20m graded crushed stone aggregate) as in levelling course/roof padding, floor finish finished even and fair, including demoliton of cement concrete (un-reinforced) roof surfaces complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces on roof surfaces of concrete surfaces in cement mortar (1:4) using with WPC complete all as specified and directed. (Note: Water proofing compond will be measured and paid seperately)

Supply only intergral water proofing compound complete all as specified and directed.

S&F drapery rod (conduit) of dia not less than 25 mm having a corrugated virgin PVC extrusion on it & finials of approved shade with standard MS powder coated/ brackets, fixed to walls with rawl plugs and steel screws complete all as specified and directed.

Dismantling, floor, hearth or wall tiling /terrazo including cement mortar bedding but not backing and removing rubbish off the premises complete all as specified and directed.

Demoltion of Brickwork or stone/boulder masonry, built in lcement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for rendering 15 mm thick in Cement Mortar (1:4) on fair faces of brick work or concrete surfaces finished even and smooth with out using extra cement, using with Integral Water proofing compound in the mortar complete all as specified and directed. (Note: WPC shall be paid and measured seperately)

M&L for rendering 5 mm thick in Cement Mortar (1:3) on fair faces of brick work or concrete surfaces finished even and smooth with out using extra cement complete all as specified and directed.

M&L for sand filling under floor in foundation including watering and consolidation complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50g and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. (Make: M/s Apex Ultima of Asian/ Weather Coat all guard of Berger/Xtra Tough of Shalimar)

M&L for complete removal of existing treatment and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50g and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces by means of mechanical scrubber and manually where the machine cannot reach complete all as specified and directed. (Make: M/s Apex Ultima of Asian/ Weather Coat all guard of Berger/Xtra Tough of Shalimar)

M&L for three coats of white wash as in ceilings on newly plastered surfaces including preperation complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with mixture of grey cement and pigment complete all as specified and directed.

Grooves for joints, tongues of cills, etc., throat (or small weather groove) as for cills, drip courses, etc. and rebates as for joints over granite or trap stone complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including cement screed and jointed over screed bed or bedding layer of mortar 20mm thick in cement mortar (1:6) for laying floor finish complete all as specified and directed.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 10mm thick in cement mortar cement mortar (1:3) complete all as specified and directed.

S&F 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter with half panel and mesh made of styles and rails of a UPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and jointed at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised MS tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickenss. The lock rail made up of 'H' section, a UPVC hollow section of size 100x30 mm and 2 mm ( + 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised MS 'U' cleats. The shutter frame filled with a UPVC multichambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by insering horizontally 6 mm galvanised MS rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineer?in-charge.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150mm long complete all as specified and directed.

S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F 4mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pan complete all as specified and directed.

S&F 1.25mm thick steel rolling shutters, with out ball bearing, as specified including top cover, an?choring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type

S&F safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

S&F ball bearing for rolling shutters complete all as specified and directed.

Supply and fix Steel windows with side hung shutters (minimum wt. of steel section should be 1.42 kg/M) including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

M&L for 75 mm thick, Cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/loose soil complete all as specified and directed.

Dismantling fencing wire mesh, any type complete all as specified and directed.

Supply only MS Galvanaised chain link fencing of size 75X75mm dia of wire 3mm complete all as specified and directed. (Note : (i) Fixing of chain link fence will e measured and paid separately. (ii) Weight of chain link fencing shall be asertain through Board of Officers).

S&F Mild steel angle iron as in Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed.

Material and Labour for rendering 10mm thick on fair faces on roof surfaces of concrete surfaces in cement mortar (1:4) mixed with water proofing compound complete all as specified and directed. (Note:-WPC measured and paid separately complete all as specified and directed).

Supply only intergral water proofing compound (liquid admixture) complete all as specified and directed. (Make : Pidilite Industries/ Impermo/Snowcem India Ltd/Sika)

M&L for preparation new surface of roof and applying two coat of polyurethene (PU) acrylic based water proofing liquid compound over & including one coat of self priming primer @one litre per ten sqm with reinforcing fabric sheet as per manufactures instruction to stop leakage /seepage from roof/wall complete all as specified and directed by the Engineer-in-Charge. (Notes- 1. As per description of the items minimum two coats of polyurethene (PU) acrylic based water proofing liquid compound over one coat of primer shall be carried out by the as per manufacture instruction.pl note no price adjustment shall be made,if more coats of (PU)acrlic based water proofing liquid compound & primer are required for roof treatment. 2. quated rate shall be deemed to be included for work in building/structure of any height).

Taking up or down steel tubing 15mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Taking up or down steel tubing 20mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

S&F 20mm dia Tubes medium grade galvanised with all fittings and fixed complete to walls, floor etc complete all as specified and directed.

S&F in repair PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe complete all as specified and directed.

S&F in repairs 15 dia fancy type chromium plated bib taps cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe complete all as specified and directed.

S&F Grating doom 125mm dia with waste hole of PTMT(mInimun weight 40gm) complete all as specified and directed.

S&F 40mm bore PVC pipes(LDPE) of pressure rating 6kg/sqcm and fixed complete to walls, ceilings or in floors complete all as specified and directed.

S&F vitreous china wash basin, white, flat back size 600x480mm, incl cutting for and pinning in ends of brackets or erecting stand but excl taps, pvc conections but incl brackets in repairs complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed.

Excavation in trenches in any type of soil n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Removing surplus excavated spoil/earth to a distance not exc.50M and deposited where directed at a level not exc.1.5 M above the starting point complete all as specified and directed.

Returning filling in soft /loose excavated soil including spreading leveling watering and well ramming in layers not exceeding 25CM and all as specified and directed.

M&L for plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) as foundation and mass filling complete all as specified and directed.

M&L for PCC 1:1.5:3 type A1 (using 20mm graded stone aggregate) Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for providing precast cement concrete louvres and jallies, 25mm thick (measured solid), including all mouldings set in cement mortar (1:4) complete all as specified and directed.

M&L for mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and directed.

All as per item item No 105.00 mentioned here-in-above but 6 to 8mm complete all as specified and directed.

All as per item No 105.00 mentioned here-in-above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

Surface excavation n.exc. 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge nexc 63mm, deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface complete all as specified & directed.

Supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and directed. (Note : Punned thickness shall be measured). (Note :- Punned thickness 18 cm shall only be considered for payment).

M&L for 100 mm thick plain cement concrete (1:4:8) type D2 (using 40 mm graded stone aggregate) as in sub base in floor/paving/ hardstanding complete all as specified and directed.

M&L for 100mm thick cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) finishing smooth & even without using extra cement complete all as specified and directed

M&L for rendering 15mm thick on fair faces on roof surfaces, finished even and fair on walls in cement mortar (1:4) using extra cement and water proofing compound, complete all as specified and directed. (Note: WPC will be measured and paid separately under relevant item).

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St-240 complete all as specified and directed.

M&L for Plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs complete all as specified and directed

S&F 0.50 mm thick Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed.

S&F 1000 Ltr capacity rotational moulded polyethylene water storage tanks (Cylindrical, vertical with closed top with three layered) confirming to relevent IS complete including provision of all inlet outlet overflow and drain pipe fitting complete including taking down old unserviceable tank complete all as specified and directed.

S&F high pressure PTMT float valve with epoxy coated alluminium rod and high density polythelene ball screwed for iron pipe 25 mm dia with fly nut complete including taking down old unserviceable float valve complete all as specified and directed.

S&F high pressure PTMT float valve with epoxy coated alluminium rod and high density polythelene ball screwed for iron pipe 25 mm dia with fly nut complete including taking down old unserviceable float valve complete all as specified and directed.

S&F in repair 25 mm bore GI Tubing medium grade in Trenches/ Floor/Pillar and connection including fitting like socket /Union/Tee/Reducer Nipple etc complete all as per specified and directed.

S&F in repair 50 mm bore GI Tubing medium grade in Trenches/ Floor/Pillar and connection including fitting like socket /Union/Tee/Reducer Nipple etc complete all as per specified and directed.

EM PORTION Taking down carefully aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified.

M&L for concealed point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including suitable size and module steel/PVC flush box and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLS PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. (Note: Quoted rate shall be included for necesasry chasing, cutting and making good as per existing specification).

All as per item No 123.00 mentioned here-in-above but One 3 pin 5 Amps socket out let points on independent board complete all as specified and directed.

All as per item No 123.00 mentioned here-in-above but 5 Amp socket on same board with other switches complete all as specified and directed.

M&L for concealed point wiring for socket outlet on independent board using 4 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including suitable size and module steel/PVC flush box and 4 sqmm nominal cross sectioanl area multistranded copper conductor FRLS PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. (Note: Quoted rate shall be included for necesasry chasing, cutting and making good as per existing specification).

S&F Modular switch 1 way 6 A, 1 module complete all as specified and directed.

S&F Modular socket 6 A -2/3 pin combined, 2 Module complete all as specified and directed.

S&F Modular Switch socket Combination 16A, 6 pin, 3 module complete all as specified and directed.

S&F Modular Fan stepped regulator, 120 W, 2 Module complete all as specified and directed.

S&F Modular white cover plate with frame 3 module complete all as specified and directed.

S&F Modular white cover plate with frame 6 module complete all as specified and directed.

S&F Modular white cover plate with frame 8 module complete all as specified and directed.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified and directed.

S&F lamp holder, PVC/polycarbonate type with back plate straight or anfular suitable for batten fittings complete all as specified and directed.

Supplying and fixing two single core ,6 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade drawing in and including suitable size PVC conduit (ISI marked medium duty), concealed, including 6 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified and directed. (Note: (i) Three runs cable and PVC conduit will be measured as a single unit. (ii) Quoted rate shall be included for necesasry chasing, cutting and making good as per existing specification).)

S&F security light fittings 25 watts, minimumm lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete suitable for pole complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as specified and directed.

S&F in reapir 18W LED light fitting wall mounted batten 4'ft , extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 18 watt,6000K including necessary connection complete all as specified and directed.

S&F in repair 9W LED light fitting wall mounted batten 2ft , extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 9 watt , 6000K including necessary connection complete all as specified and directed.

S&F Vertical distribution board double door TPN 4 way with IP 43 multiphase outgoing suitable for mounting 100 Amps as incomer with Bus bars, Neutral links complete with all accessories complete all as specified and directed.

S&F in repairs epoxy powder coated sheet metal enclosure for DBs, double door, Single pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and directed.

S&F MCCB of 4 pole , 415volts of capacity 100 Amps with breaking capacity of 16 KA Fixed thermal and fixed magnetic setting including necessry connection complete all as specified and directed. (Note :-Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F in repairs MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note :-Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

S&F in repairs MCB SPN 6-32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed. (Note :-Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 25 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate No 3 of SSR Part I complete all as specified and directed and testing on completion. (Note :- (i) If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department. (ii) Testing to be carried out by the contractor in presence of Engr- in- Charge , entered in the eath testing register, prepared and to be maintained by the contractor & submited to Concerned JE E/M. (iii) T&P and testing instrument(Meger) to be provided by the contractor at own cost).

S&F metallic Exhaust ventilation fan of sweep 230 mm sweep, 230volt AC heavy duty complete with louver and all asssesories including cutting hole of suitable size, making good surface by doing plaster and applying two coat of distemper complete with fixing connected with twin core twisted flexible copper conductor (23/0.0076) of size complete all as directed by Engr-in-Charge.

Taking down of AC ceiling fan of any sweep & any height and opening the fan and oiling, greasing and replacement of unserviceable accessories and servicing, complete overhauling and re-assembling and testing complete for efficient functioning and hanging it back in position including provn of 0.5 Sqmm copper flexible twin twisted cable (length not exceeding 0.5 metre) from ceiling rose to fan as directed by the Engr-in-Charge.

M&L for painting of ceiling fans upto 1400mm sweep carefully, dismantling fan blades and paint with one coat of synthetic enamel paint including filling cavities with filler after cleaning all dust etc complete all as specified and directed.

Supply, laying / fixing / connecting, testing and commissioning of 35 Sqmm x 3.5 Core LT under ground cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cable (heavy duty) with multistranded aluminium conductor,1100 Volts grade in trenches/on wall/poles laid in ducts/inside protection pipe of the following cross sectional area including cable glands,lugs and suitable size of MS saddle clips (where ever cable laid in ceilings / walls without cable duct) all as directed by the Engr-in-Charge. (Note : (i) Earth work in excavation, sand cushioning, cable cover, cable protection, GI pipe shall be measured and paid separately under relevant item. (ii) Cable Route Indicator made of metal of height 300mm above GL duly written ''LT CABLE'' to be fixed on every 30 mtr distance with pcc (1:3:6), 150 mm below the GL ,cost of indicator and pcc to be considered in this item rate).

All as per item No 149.00 mentioned here-in-above but cross section area of cable 16 Sqmm x 4 Core complete all as specified and directed.

Supply and lay in trenches fly ash bricks, for cable protection all as specified and directed by the Engr-in-Charge.

S&F Pipes galvanized, 50 mm bore “light grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement or specified .

S&F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB, 240V, 20 Amps complete all as specified and directed.

Supplying and fixing two single core, 4 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade drawing in and including suitable size PVC casing caping (ISI marked) including 4 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified and directed. (Note: Three runs cable and PVC casing caping will be measured as a single unit)

S&F voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 130 V to 280 V with output voltage stabilized at 230 V with accuracy of + 2.5% of capacity 4 KVA complete all as specified and directed.

S&F Split units indoor/ outdoor complete with cordless remote control unit and with in built air ioniser and plasma filter for better indoor air quality with 5 star rating of capacity 1.5 TR complete all as specified and directed

MS ROYAL CONSTRUCTION INDEX NO 158 2010 BKP