Balance work for Construction of 5000 MT Capacity Cold Storage at Ranchi (Mandar) District

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 m including all lifts, levelling , ramming the foundation trenches, removing roots of trees, serbs all complete as per approved design,building specification & direction of E/I.

Providing coarse clean local sand in filling in foundation trenches or in plinth including ramming and watering in layer not exceeding 150mm thick with all leads and 1.5M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer Incharge (Mode of measurement compacted volume)

Providing RCC M-200 with nominal mix of (1:1.5:3) in foundation and plinth with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer, placing in position vibrating striking curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/I.

Providing TMT reinforcement of following dia rods as per approved design and drawing including carriage of M.S. rods of (Straight or in coils) to work site, cutting, bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.

Earth filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing designation 75A brick work in CM (1:6) in superstructure with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 and including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I

Providing 6 mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I.

Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion

110 mm bend

Shoe (Plain)110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

Providing 2 coats of Synthetic Enamel Paint of approved shade and make over steel surface grills & railings including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing fully glazed steel door, windows or ventilations of standard rolled 'Z' and mullion steel sections and size as per IS-1038 joints met and welded with 100x16x3mm M.S. lugs fixed in cement concrete (1:2:4) blocks 15x10x10 cm size including cost of oxidised iron fittings, with hinges, handle per steps, catch springs, 3mm thick plain glass panes with Aluminimum beads and inner frame fixed with lugs with 20mm long 6.3mm G.I. counter sunk machine screw and nuts and applying a coat of red lead paint carriage to work site hoisting and placing in position in all storys and taxes all complete as per building specification and direction of E/l.

Providing two coats of synthetic enamel paint over a coat of primer of approved shade and make over new wooden surface after cleaning, removing dirt, scales, smokes, grease and sand papering, including cost of scaffolding and taxes all complete as per building specfication and direction of E/l.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing rust , dirt, , scales , smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/l. ( Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification)

Cairage Of Meterial

Sand 15 KM

Aggregate 15 KM

Brick (1+7) KM

S/F sheet metal ON/OFF- Load changeover:-Providing and fixing following capacity 2pole/4pole On /OFF Load changeover switches with side handle operiation , in sheet encloser in existing metal board including drilling holes in metal board , making connection ,earthing yhe body etc as required 200 amps, 4pole

200 amps, 4pole

S/F 'C' series SP MCB: Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.

6/32A TPN MCB

50/63A TPN MCB

6/32 amps single pole "B" series

150 sq mm 3.5 core

95 sq mm 3.5 core

35 sq.mm 3.5 core

Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x6.0 Sq.mm + 1x6.0 Sq.mm earth wire (

2x10.0 Sq.mm + 1x10.0 Sq.mm earth wire

4x6.0 Sqmm + 2x6.0 sqmm earth wire

4x10 Sqmm +2x10 sqmm earth wire

G.I. Earth pipe Elecrode with salt/charcoal:- Earthing with G.I. earth pipe 3 m, 40 MM dia including accessories and providing massonary enclose with cover plate having locking arrangement and watering pipe etc with charcoal and salt

S/L 8 SWg copper wire inground:- Supplying laying 8 SWg wire at 0.50 meter below ground level for conductor earth electrod ,including soldering etc. as required

P/F GI lightning conductor finial :- Providing and fixing of lighting conductor finial, made of 25mm dia 300mm long copper tube, having single prong at top, with 85mm dia 3mm thick copper base plate including holes etc. complete as required.

Reverting, sweating, and soldering lightning conductor tape:- Reverting, sweating and soldering of copper/G.I. tape (with another copper/ G.I. tape, base of the finial or any other mettallic object) etc. as required.

P/F GI lightning conductor tape in horizontal run:- Providing and fixing tape 20MM x3MM thick on parapet or surface of wall for lighting conductor complete as required (for horizontal run)

P/ F G.I Lightning conductor tape in vertical run :- Providing and Fixing copper Tape In vertical run: Providing and fixing of copper tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete etc. as required (vertical run).

P/F MV Danger Notice Plate:- Providing and fixing M.V. danger notice plate of 200mmX150mm, made of mild steel at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in the single red colour on front side as required.

P/F MV Danger Notice Plate:- Providing and fixing H.T danger notice plate of 250mmX200mm, made of mild steel at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in the single red colour on front side as required.

Supply Installation, Testing & Commissioning of following sizes ceiling fan 3 Blades confirming to IS:374:2019 including wiring the down rods of standard (up to 30cm) with 1.5 sq.mm FR PVC insulated copper wire suitable for 230V 50 Hz, Single phase supply etc. complete as required. Make :- Usha/Crompton / Havells . 1200 mm ( 48") Ceiling Fan

S/F Modular type electronic fan regulator: Supplying and fixing stepped (two module) type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.

ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

S/F light plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 5 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.(Note:- Near all LAN points 3 Nos. 5/6 Sockets with Switch, all switch borads with sockets indifferent rooms, all 5/6A separate switch sockets, all corridor and stair case 5/6A socket switch for Fire alarm system, all racks for lLan must have one 5/6A socket with switch with UPS support etc.

S/F power plug point with modulartype accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.

S/F TP MCB DB: Supplying and fixing following way,three pole and neutral sheet MCB distribution board, 415 volts on surface/recess complete with tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections,phosphatised and powder painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR).

4 ways (4+12) Double Door. (horizontal type

6 ways (4+18) Double Door. (horizontal type

8 ways (4+24) Double Door. (horizontal type

S/F Modular type blanking plate :- Supplying and fixing modular blanking plate on existing modular plate and switch box excluding modular plates as required

Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.

Group- C

Supplying and erection of galvanised ‘D’ iron clamps complete with shackle insulator (75 mm X 90 mm),G. I. bolts, nuts and washers, coach screws etc. as required.

Supplying and erection of 75 mm X 90 mm shackle insulator with G. I. Bolt, nuts and straps etc. as required.

Supply and installation of Silent type Diesel Generating set alongwith having prime power Rating Suitable to Drive of 320 KVA, 415 Volt at 1500 RPM, 0.8 lagging power factor at 415V suitable for 50 Hz, 3Phase system generator & for 0.85 Load Factor incuding AMF Pannel for 320 KVA DG Panel

PUF PANEL Thermal Insulation (Ground Floor)

Wall Panel Supply of BNAL Make 100mm Micro Ribbed Continuous Line PUF Wall & Ceiling Panel having 0.5mm TCT PPGL Sheet on both sides, PUF Infill Density 40±2 Kg/M3.RAL 9002 (Sheet Make - JINDAL/TATA & Chemical - Dow/BASF)

CeiIing Panel Supply of BNAL Make 100mm Micro Ribbed Continuous Line PUF Wall & Ceiling Panel having 0.5mm TCT PPGL Sheet on both sides, PUF Infill Density 40±2 Kg/M3.RAL 9002 (Sheet Make - JINDAL/TATA & Chemical - Dow/BASF)

Partition Panel in depth( 1 Nos.) Supply of BNAL Make 100mm Micro Ribbed Continuous Line PUF Wall & Ceiling Panel having 0.5mm TCT PPGL Sheet on both sides, PUF Infill Density 40±2 Kg/M3.RAL 9002 (Sheet Make - JINDAL/TATA & Chemical - Dow/BASF)

Partition Panel Supply of BNAL Make 100mm Micro Ribbed Continuous Line PUF Wall & Ceiling Panel having 0.5mm TCT PPGL Sheet on both sides, PUF Infill Density 40±2 Kg/M3.RAL 9002 (Sheet Make - JINDAL/TATA & Chemical - Dow/BASF)

Door Accessories without heater( Swing Door)

Hatch window with/without heater

Sealant for puff panel joints filling.

Bulk Head

Presser Relief Valve without heater

SLIDING DOOR (1500 x 2100mm)

PUF PANEL Thermal Insulation ( First Floor )

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Wall Panel Supply of BNAL Make 100mm MicroRibbed Continuous Line PUF Wall & Ceiling Panel having 0.5mm TCT PPGL Sheet on both sides, PUF Infill Density 40±2 Kg/M3.RAL 9002 (Sheet Make - JINDAL/TATA & Chemical - Dow/BASF)

Ceiling Panel Supply of BNAL Make 100mm Micro Ribbed Continuous Line PUSupply of 80mm PUF Slab with both side Craft PaperF Wall & Ceiling Panel having 0.5mm TCT PPGL Sheet on both sides, PUF Infill Density 40±2 Kg/M3.RAL 9002 (Sheet Make - JINDAL/TATA & Chemical - Dow/BASF)

Floor panel Supply of 80mm PUF Slab with both side Craft Paper

Sealent

Bulk Head

Presser Relief Valve without heater

SLIDING DOOR(1500 x 2100)

Hanging Accessories

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

CHAMBER -2 MULTI COLD STORAGE.

Air Cooled Condensing Unit for Multi Cold Storage Chamber. F150 Condensing Unit with 4GE-30Y Single Stage Semi-Hermetic Reciprocating Compressor operating at -2°C Evaporating Temperature with 50.5 KW(14.4TR)& +50°C Condensing Temperature . This Condensing Unit consisting Condenser, Compressor, Condenser Fan with Motor, HP/LP Switch, Liquid Solenoid, Filter Drier, Sight Glass, Oil Pressure Switch, Discharge Vibrator, NRV for Discharge Line, Accumulator, Receiver & Oil Seperator. Connected Load is 26.65 kW with Ic.Regular Evaporator unit

Electrical Panel

Copper piping between IDU & ODU.

Stand Evaporator hanging

Referigerant R 404a Gas

Cable(R. feet)

Service

CHAMBER -3&4 FRUITS &VEGETABLES(GROUND FLOOR)

Air Cooled Condensing Unit for Fruits Chamber & Vegetable Chamber D047 Condensing Unit with ZB26 Hermetic Scroll Compressor operating at -2°C Evaporating Temperature & +50°C Condensing Temperature with 20.8 kW(5.95TR). This Condensing Unit consisting Condenser, Compressor, Condenser Fan with Motor, Split Valve, HP/LP Switch, Liquid Solenoid, Filter Drier, Sight Glass, Receiver & Oil Seperator Connected Load is 9.45kW with Ic.Regular Evaporator unit

Electrical Panel

Copper piping between IDU & ODU.

Stand Evaporator hanging

Referigerant R 404a Gas

Cable(R.Ft)

Service

CHAMBER -1 POTATO.(FIRST FLOOR. )

Air Cooled Condensing Unit for Potato Chamber. F150 Condensing Unit with 4GE-30Y Single Stage Semi-Hermetic Reciprocating Compressor operating at -2°C Evaporating Temperature with 50.5 KW(14.4TR) & +50°C Condensing Temperature . This Condensing Unit consisting Condenser, Compressor, Condenser Fan with Motor, HP/LP Switch, Liquid Solenoid, Filter Drier, Sight Glass, Oil Pressure Switch, Discharge Vibrator, NRV for Discharge Line, Accumulator, Receiver & Oil Seperator. Connected Load is 26.65 kW with Ic.Regular Evaporator unit

Electrical Panel

Copper piping between IDU & ODU.

Stand Evaporator hanging

Referigerant R 404a Gas

Cable(R.Ft)

Service

Control Panel Including PLC

Boaring

Providing P.C.C.M - 100 with nominal mix of (1:3:6) in foundation with approved quality of stone metal grade III (50mm to 25mm size) clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/l.

providing R.C.C.M - 150 with nominal mix of (1'2"4 ) in foundationland plintn with approvecl qLrality of stone chips 20 mm to 6 mm'lsize qraded and clean ccarse sand of F M 2 5' to 3 includingl=.roJnino shuttering' mixing cement concrete in mixer and lptucing in position, vibrating, striking, curing (butexcluding theicost of renifr-,rcement, taxes and royalty all complete' as per,ritCino s',:ecification :rnd direction of E/l

Providing designation 75 B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Electrical

CABLE TRAY FOR SUPPORTING CABLE INCLUDING SUPPORTING FLENGE & CABLE TRAY SUPPORT BRACKET 600 mm width X 62.5 mm depth X 2.0 mm thickness

Providing and fixing in position 25 mm thick bituminastic board (shalitex or Equivalent as per IS:1838-1983) in expansion of construction joints in barrage and its allied works as per specification and direction of E/I

Providing and fixing sheet covering over expansion joints with iron screws as per design. Aluminium fluted strips 3.15 mm thick. 200 mm wide

Design Manufacture, Supply of 16 SWG sheet steel fabricated cubical type floor mounting front operated construction,encloser class IP-52, finishing with 7 tank process and power coating of the entire panel including covers in required shape complete with top/ bottom ( as called for ) removable gland plates, cable alleys, double compression door to achive dust and vermin proof complete all inter connection small wiring by copper wire , ckt labels etc. The copper Bus Bar shall be of suitable size for 500 Volts 3 phase 50 HZ TPN, electrolytic copper as per IS 8623 insulated by heat shrinkable sleaves with surrounded joints. the instrument chamber sahall be separated and shall comprise of flash type ammeter ,....

LT Panel : 600 Amp Incoming ( 1 Sets) each with following .

Bus Bar

1 sets of 630 amp, 415V ,3 Pase , 50 Hz Al. Busbar.

S/F HRC fuse type TP&N switch Disconnector Providing and fixing following capacity double pole TP&N sheet metal switch disconnector fuse switch unit inexisting metal board with ISI marked HRC fuses including drilling holes in metal board , making connections, etc. as required.

Installation, Testing and commissioning of LT Panel as describe above.

S/F AMF Pannel for 320 KVA DG Panel

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

125 Amp , 16 KA , FPMCCB

Supplying and fixing following rating, double pole, (single phase and neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliampapers in the existing MCB DB complete with connection, testing and comissioning etc. as required.

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

100 Amps ,16 KA ,FPMCCB

Supplying and fixing following rating, double pole, (single phase and neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliampapers in the existing MCB DB complete with connection, testing and comissioning etc. as required.

S/F HRC fuse type TP&N switch Disconnector Providing and fixing following capacity double pole TP&N sheet metal switch disconnector fuse switch unit inexisting metal board with ISI marked HRC fuses including drilling holes in metal board , making connections, etc. as required.

200 Amps ,36 KA ,FPMCCB

Supplying and fixing following rating, double pole, (single phase and neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliampapers in the existing MCB DB complete with connection, testing and comissioning etc. as required.

S/F HRC fuse type TP&N switch Disconnector Providing and fixing following capacity double pole TP&N sheet metal switch disconnector fuse switch unit inexisting metal board with ISI marked HRC fuses including drilling holes in metal board , making connections, etc. as required.

200 Amps ,36 KA ,FPMCCB

Supplying and fixing following rating, double pole, (single phase and neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliampapers in the existing MCB DB complete with connection, testing and comissioning etc. as required.

3C x 400 sqmm 11/11 KV HT XLPE ALUMINUM CONDUCTOR ARMOURED CABLES (KEI)

Laying of one number PVC insulated ans PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing masonry open duct as required.

up to 35 sq mm

above 35 sq.mm and up to 95 sq mm

MV Cable Laying up to 400 sq. mm. in trench :- Laying of one number additional PVC Sheathed / XLPE power cable of 1.1 KV grade of size not exceeding 120 sq.mm. but not existing 400 sq.mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.( for 150 Sqmm cable)

MV Cable Laying up to 400 sq. mm. in trench :- Laying of one number additional PVC Sheathed / XLPE power cable of 1.1 KV grade of size not exceeding 120 sq.mm. but not existing 400 sq.mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying and fixing of one number PVC insulated ans PVC sheathed / XLPE Power cable of 1.1 kV grade of following size on wall surface as required.

Upto 35 Sq.mm ( clamp with 1mm thick saddle)

Above 35 Sq.mm and up to 95 sq. mm ( Clamp with 25x3mm MS Flat clamp)

Above 95 Sq.mm and up to 185 sq. mm ( Clamp with 25/40x3mm MS Flat clamp)

Above 185 Sq.mm and up to 400 sq. mm ( Clamp with 40x3mm MS Flat clamp)

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing material for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

3.5 X 35 sq. mm

3.5 X 95 sq. mm

3.5x150sq.mm

3.5x400sq.mm

Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 Sq.mm + 1x1.50 Sq.mm earth wire

2x2.5 Sq.mm + 1x2.5 Sq.mm earth wire

2X4 Sq mm +1X4 Sq. mm Earth wire

Hot dipped Galvanized Iron Cable Tray 450mm width X 50 mm deph X 2.0 mm thickness

Power Plug wiring in PVC conduit ( 2 x 4 Sqmm):- Wiring for light / Power plug with 2x 4 Sq. mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit along with 1 nos. 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required :-

S/L 25mm x 5mm G.I earth strip in ground :- Supplying laying 25mm x 5mm G.I strip at 0.50 meter below ground as strip earth electrode, including soldering etc. as required.

supply of Exhaust Fan 380 mm sqeep

S/F Modular boxes, base & cover plate :- Supplying and fixing following size/ modules G.I box along with modular base & cover plate for modular switches in receess etc as required.

8/9 MODULE (78MM X 230MM X 60MM)

12 MODULE (135MM X 205MM X 60MM)

4/5 Module (78 mm X140mmx50mm)

6 Module (78 mm X205 mmx50 mm)

Supplying of surface /pendent mounting industrial T5 luminari

Supplying of surface /Pendent Mounting T5 luminaires 150 W

Double LED tubelight fittingmade of die castaluminium housing 2x20 watt bettel tubelight suitable for surface mounted.

Suppying of CFL Bulk Head luminaires

SITC of 150 watt LED STREET LIGHT

Providing and Fixing of CO2 Portable 4.5 Kg Fire extinguisher, Carbon-Dioxide type Flat base Horn Including Valve, High Pressure Rubber Wire Braided Discharge Hose of not less than 10 mm dia. & complete in all respects including initial fill with CO2 Gas confirming to IS:15222. and IS 15683:2018 Marked.

Supply & Fixing of 6 Kg ABC MAP-50% Powder based Fire Extinguisher, Applicable Fire Class A, B & C, EPDM Rubber Hose, NRV Valve and Helium Leak Detection Tested, Internal Coating - Epoxy Powder and External Pure Polyester Powder Coated (UV resistant), IS 15683:2018 Marked.

S&F installation ,testing and commissioning of 11/0.415 KV (350KVA) 3 Phase oil immeresed step down distribution transfermer for out door installation

Supply and errection of 100 mm x 65 mm pin insulator complete with G.I spindle and nut etc. as required.

Supplying of C.C .pole up to 11 m in B.B:- Supply of RCC/PCC pole of length excluding 8 meter but not exceeding 11 meters.(CP-1.15%)

Erection of Pole up to 11 m in B.B:- Erection of RCC/PCC, pole of length exceeding 8 meters but not exceeding 11 meters in bricks ballast and ramming the foundation including excavation and refilling etc. as required.

Supply of HT PANEL 11 KV (Enclosure)

VCB ( Vacume Circuit Breaker)

Isolator

Multi Function Meter

Potential Transformer ( PT)

Current Transformer ( CT)

Over load relay

Earth Fault

R,Y,B Indication Lamp

Instaulation testing and commesning

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Supplying of Cpacitor Panel : ( 36 KA ) Incoming ( 100 Kvar)

Bus Bar

One set of 300 Amp, 415 Volt, 3 Phase ,TPN Cu Bus bar.

Out going

For 10KVAr – 3 STEPS

MCCB, 3P, 36KA CVS TMD type - 3Nos -25A TVS E type, TP, Power Contactor – 18A - 3Nos 7% detuned reactor, 440V, Al wound type - 10kVAr - 3Nos

For 20KVAr – 1 STEP

MCCB, 3P, 36KA CVS TMD type -50A - 1 No. TVS E type, TP, Power Contactor – 50A - 1 No. 7% detuned reactor, 440V, Al wound type - 20kVA - 1 no.

For 50KVAr – 1 STEP

MCCB, 3P, 36KA CVS TMD type -100A- 1 No. TVS E type, TP, Power Contactor – 95A 1 No. 7% detuned reactor, 440V, Al wound type - 50kVAr - 1no.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Installation, Testing and commissioning of APFC Panel as describe above

300 SQMM HEAT SHRINKABLE 6.6 KV (E/UE) 11KV (E) XLPE OUT DOOR TERMINATIONS (3 CORE) (DENSONS)

Supplying and installaton of conduit pipe

20mm dia ISI marked , PVC pipe

20 mm dia Flexible pipe

20 mm bend

20 mm four way PVC moduled circular with lead and screw

Fan Hook

Supplying and I fixing following moduler switch/soket on existing moduler plate & switch box including connection but excluding modular plate . As required.

5/6 A Switch

15/16A switch

3pin 5/6 A soket outlet

6m/pin 15/16 A soket outlet

400 sq mm 3.5 core

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).

Providing 1.5mm cement punning including curring,carrage of water--do---do-- as per building specification.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets,40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid each

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass painting of fittings and brackets, cutting and making good the walls pillar taps, 32 mm C.P. brass waste of standard pattern, including wherever require:

White Vitreous China Wash basin size 630x450 mm witha pair of 15 mm C.P. brass pillar taps

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings

15 mm dia

20 mm dia

25 mm dia External

S/F/F PVC water Storage Tank all complete job

Construction of Inspection chamber all complete job-

Supply fitting and fixing Bath room fittings of approved make with ISI Mark all complete as per specification and direction of E/i

100 mm Steel Jali

Soap dish

Bib cock long thread

Angular Stop cock

Mirror of 6 mm thick 600 x 450 mm

Pillar Cock (ISI) long Neck

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominalsize) over 75mm thick bed of dry brick ballast 40 mm nominal size,well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. sqm 614.05

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

With material conforming to Grade-II (size range 53 mmto 0.075 mm ) having CBR Value-25

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cementratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratoryroller, finishing and curing etc. complete as per direction of Engineerin- charge

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brushetc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum.Excess/less cement used as per design mix is payable/ recoverableseparately).

60mm thick Paver block of M35 grade with approved colour,design & pattern

Providing 250 mm wide brick drain in C M (1:6) all complete job

Sub Total (B)

NEW ITEM

Centering and shuttering including strutting, propping etc. and removal of form for all heights

Foundations, footings, bases of columns, etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in roof members as pillars, plates, rafters, purlines, beams any type of batten with cost of nuts and bolts complete with cleats (with wooden checks) fitting with screws all complete as per building specification and direction of E/l.

Bamboo work in chailis bamboo?(i) 75 mm dia 6 to 8 m long(84.20+10% C.P+5% OH+ 5% installation

ADD FREIGHT LIFT (Quotation attached)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately).

All works upto plinth level

Concrete of M25 grade with minimum cement content of 330 kg /cum

All works above plinth level upto floor V level

Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing Tor steel reinforcement of 8mm. dia rods as per approved design and drawing -do- -do- TMT Fe 500 {Only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel steels Ltd. Bokaro and Vizag (RINL)}

a) 10 mm (TMT coiI Fe 500) {Only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel steels Ltd. Bokaro and Vizag (RINL)}

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface inluding preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required sacaffolding washing of floors and taxes all complete as per building specification and direction of E/I

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and applying heigh quality acrilic modified resine based texture of Dholpur/red sand stone ….....................of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush shutters in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of standard make with oxidised iron fittings -- do ---

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

single rubber stoper

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike­ plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer­ in-charge:

Profile B

Fixing with adjustable lugs with split end tail to each jamb

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

HORTICULTURE

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)

Holes 90 cm dia, and 90 cm deep

Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Bauhinia blakeana (Kachnar) of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.v

Providing and fixing M. S. tree guard 50 cm square in plan, height 1.40 metre above ground level and 0.50 metre below ground level. The vertical members shall coMRst of four nos of angle iron of size 25x25x5 mm 1.9 long, one at each corner and 8 nos flat iron of size 25x5 mm 1.4 long. The vertical members shall be welded to 4 nos 25x6 mm M. S. flats placed horizontally around the vertical member of the cage. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground , including refilling the earth, compaction etc. complete. The tree guard shall be painted with two coats of paint of approved brand and manufacture over a coat of primer, complete in all respect.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)

Trees Plant

Supplying and stacking at site dump manure from approved source, including carriage up to 5 km Complete (manure measured in stacks will be reduced by 8% for payment) :

Screened through sieve of I.S. designation 20mm

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). C

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Supplying and stacking sludge at site including royalty and carriage up to 5 km (sludge measured in stacks will be reduced by 8% for payment).

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

In rows 5 cm apart in both directions.

Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge.

Borewell

Cost of Drilind 200mmx165mmx125m dia Deep Bore well in all kind of soil and rock in rural area for instalation of pump set with hydrolic DTH rig machine all complete including all materials ,tools ,drilling rig air compressureand equipmentsas well as fuel ,lubricantsand of rig machine and other vehical up to site .

(a) From 0.0m to 50.0 m Below G.L

(b) From 51.0 to 125.0 m Below G.L

(C) From 126M to 150.0 m Below G.L

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing(CM) pipe OF Required dia, conforming to IS:12818, including required hire and labour charge , fitting & accessories etc . All complete, for depths as per direction of engineer in charde-200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (partI) IS :11189 to establish maximum rate of usable water yield without sand content ( beyond permissible limit) with required capacity air compressor ,running the compressor for required time till well is fully developed ,measuring yield of well by V notch method or any other approved methode ,mesuring static level & drwan etc by step drawn down method collecting water samples & getting tested in approved laboratory i/c disinfection of tube well all complete hire & labour charges of air compresssor ,tools & accessories stc all as per requirement and direction of engineer in charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well 200 mm dia

Providing and fixing M.S Clamp of required dia to the top of casing pipe of tube well.200 mm dia

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump.Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supply fitting and fixing of standard make starter panel board with arrengement of all neccessery protection including all tax , all complite job as direction of E/I

Supply fitting fixing 3 core 4 sqmm flate copper submersible cable including all tax royalty Etc all complite job as per direction E/I

Supply fitting and fixing lowering 40mm dia G.L column pipe do-do- all complite job as per direction of E/I

Add 18% GST

Add 1% Labour cess 1%

Manish Kumar Singh (BID ID -659784)