Design, build, construct, install , and commissioning of Material Recovery Facility (MRF) of 50 TPD for dry waste along with operation and maintence of the plant for 5 years on EPC Mode...

BILL OF QUANTITY

Name of Work Construction, Installation and Commissioning of 50 TPD capacity MRF under Nagar Nigam Saharsa in Saharsa District

sl.no. BCD CODE Item OF Works Unit Qty. Rate in Rs. Amount in Rs

1 2.29.1 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5m All kinds of soil. 100Sqm 6160 1355.40 83493.00

2 2.25A Excavating, supplying and filling of local earth (including royalty but excluding cairriage cost) by mechanical transport upto a lead of 3km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. If local earth is available at more than 3 km lead the actual lead must be approved by compitent authority. cairraiage of material will be paid seperately and calculated after deducting initial lead. cum 23487.50 411.70 9669803.75

3 20.2.1 Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).:-300mm dia pile m 624 902.60 563222.40

4 2.8.1 Earthwork in excavation in areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including dressing of sides and ramming of bottom, lift upto 1.5 including getting out the excavated soil and disposal of surplus soil as directed within a lead of 50m. All Kind of soil. cum 3,811.88 360.70 1374946.38

5 2.27.1 Extra for every additional lift of 1.5 m or part thereof in : All kinds of soil cum 1511.844 49.40 74685.09

6 11.72 Providing designation 100A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. sqm. 1,576.62 283.30 446656.16

7 2.28 Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete. cum 4,105.78 287.30 1179590.06

8 4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level. 1:2:4(1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) cum. 159.29 3998.10 636868.94

9 5.33A.1+5.33B.1 Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete. Add or deduct for providing richer or leaner mixes respectively at all floor levels. Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C. All work upto plinth level. Add or deduct for providing richer or leaner mixes respectively at all floor levels. Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C. cum. 1201.25857 4921.40 5911873.93

10 6.41A Brick work with selected bricks of class designation 100A in exposed brick work including making horizontal and vertical irooves 10mm wide 12mm deep complete from ground level up to plinth level in cement mortars 1:6(1 cement: 6 corse sand) Cum. 85.5 4925.20 421104.60

11 2.26 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead Cum. 1200.34145 123.90 148722.31

12 6.41A + 6.45A Brick work with selected bricks of class designation 100A in exposed brick work including making horizontal and vertical irooves 10mm wide 12mm deep complete from ground level up to plinth level in cement mortars 1:6(1 cement: 6 corse sand) Extra for exprosed brick work in superstructure above plinth level and upto floor level. 0.75 x 1.5 = 1.13 Cum. 416.5625 5993.20 2496542.38

13 6.18.4A +6.19A Half brick masonry with bricks of class designation 100A in foundation and plinth cement mortar cement mortar 1 : 4 (1 cement : 4 coarse sand) and extra for half brick masonry in superstructure above plinth and upto floor V level. Cum. 393 689.00 270777.00

14 5.33A.2.1+5.33B.1 Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete. All works above plinth level upto floor V level. Walls columns, pillars, posts cind struts. Add or deduct for providing richer or leaner mixes respectively at all floor levels. Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C. cum 99.12575 5458.00 541028.34

15 5.33A.2.2+5.33B.1 Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete. Add or deduct for providing richer or leaner mixes respectively at all floor levels. Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C. All works above plinth level upto floor V level. Beams, planth beams, girders, bressumers, contilevers, Suspended floors lintels roofs and staircases including spiral staircases, shelves etc. Add or deduct for providing richer or leaner mixes respectively at all floor levels. Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C. cum 53.7884375 5841.70 314215.92

16 5.1.3 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level. 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size) cum 0.93 4232.40 3938.51

17 13.11.4 12 mm cement plaster of mix ; 1:6 (1 cement : 6 coarse sand) sqm. 1503 141.50 212674.50

18 13.20 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement :5 coarse sand) and top layer 6 mm thick, cement plaster 1:3 (1 cement: 3 coarse sand) finished rough with sponge. sqm. 2645.00 227.40 601473.00

19 13.24.2 6 mm cement mix plaster of mix 1:3(1cement:3coarse sand) of ceiling. sqm. 392.00 125.60 49235.20

20 13.17.1 + 13.26 + +13.36.1 12 mm cement Plaster 1:3 (1 cement: 3 coarse sand) with a floating coat of neat cement & Extra for providing and mixing water proofing material in proportion recommended by the manufacturers: 12 mm cement plaster 1:3(1 cement :3 sand) sqm. 52.82 253.10 13368.74

21 13.13.1 + 13.26 + 13.36.5 20 mm cement Plaster 1:3 (1 cement: 3 coarse sand) with a floating coat of neat cement & neat cement punning sqm. 16.65 280.90 4676.99

22 16.78.1 Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 cum. 659.625 1310.40 864372.60

23 4.1.1 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1:1:2 ( 1 cement: 1 coarse sand:2 graded stone aggregate 20 mm nominal size) cum 11.3685 5687.00 64652.66

24 11.3.1 + 11.8 Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate. Extra for making chequers of approved pattern on cement concrete floors, steps, landing, pavemerts etc sqm. 392 325.40 127556.80

25 13.80 A.2 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. sqm. 2058.68 105.40 216984.87

26 13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) sqm. 2671.3 137.00 365968.10

27 13.77.2 Distempering with oil bound washa ble distemper of approved brand and manufacture to give an even shade .New work (two or more coats ) over and including priming coat with cement primer sqm. 2058.68 102.30 210602.96

28 9.21.2 Providing and fixing flush door shutters conforming to IS : 2202 (Part-I) non-decorative type.core of block board construction with frame of 1st class tiard wood and well mathched commercial 3 ply veneering wiih vertical grains or cross bands and face veneers on both faces of shutters.30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws sqm. 61.74 1641.50 101346.21

29 9.127.2 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality .1.0 mm thick sqm. 61.74 669.00 41304.06

30 9.1.2 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) sqm. 1.2975 95670.70 124132.73

31 9.40.1.1 Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete2nd class teak wood 50x12mm cum. 25 137.30 3432.50

32 9.100.1 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: 125 mm cum. 40 57.10 2284.00

33 9.101.2 Providing and fixing alluminium hanging floor door stopper anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc.complete:Twin rubber stopper cum. 20 60.80 1216.00

34 9.97.2 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade, with necessary screws etc. complete: 250x10mm cum. 40 98.20 3928.00

35 13.81.1 Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and softwood) sqm. 123.48 39.70 4902.16

36 13.81.3 Applying priming coat with ready mixed zinc chromate yellow primer of approved brand and manufacture on steel galvanized iron/steel work. sqm. 29.535 34.60 1021.91

37 13.93.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work sqm. 194.04 84.50 16396.38

38 5.9.1 Centring and shuttering including strutting, proping etc. and removal of form for foundation, footings, bases of columns etc. for mass concrete. sqm. 802.464 211.60 169801.38

39 5.9.5 Centring and shuttering including strutting,propping etc. and removal of form for Lintels, beams, plinth bams, griders, bressumers and contilevers. sqm. 1235.506 404.70 500009.28

40 5.9.6 Centring and shuttering including strutting , Propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts. sqm. 1472.814 494.40 728159.24

41 11.38 Providing and laying ceramic glazed floor tiles 300 x 300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in all colors, shades, except white .Ivory, Grey,Fume red, Brown laid on 20mm thick bed of cement Mortar 1:4 (1 cement :4 coarse sand) including pointing the joints woth white cement matching pigments etc complete. sqm. 430 862.40 370832.00

42 11.36 Providing and fixing 1st quality Ceramic glazed wall tiles conforming to IS : 15622 {thickness to be specified by the manufacturer} of approved make in all colours,shades, except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of step and dados over 12mm thick bed of Cement Mortar 1:3 (1 cement : 3 Coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigments of matching shade complete. sqm. 174 795.00 138330.00

43 10.18 Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. each 16 165.40 2646.40

44 5.22 Reinforcement for RCC work including straightening, cutting, bending, placing in position and bonding all complete.-

(i) 5.22.7A (i)Thermo-Mechanically Treated bars TMTC-500-8mm dia. KG. 9396.406 94.50 887960.40

(ii) 5.22.7B (i)Thermo-Mechanically Treated bars TMTC-500-10mm dia. KG. 14968.279 92.60 1386062.62

(ii) 5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia. KG. 26113.840 90.80 2371136.69

(ii) 5.22.7D Thermo-Mechanically Treated bars TMTC-500-16mm dia. KG. 52785.398 91.70 4840421.03

45 16.79 Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge. cum. 160.22 1251.50 200515.33

46 16.75 Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum.Excess/less cement used as per design mix is payable/ recoverable separately). cum. 427.24 5842.70 2496235.15

47 12.1.1 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. sqm. 3825.25 1792.30 6855995.58

48 12.9.1 Providing and fixing 15 cm wide 45 cm over all semi circular plain G.S. sheet gutter with iron brackets 40x3 mm size bolts, nuts and washers etc. including making necessary connections with rain water pipes complete. m 74 577.40 42727.60

49 6.1.12/1 Brick work with bricks of class designation 100A in foundations and plinth in : Cement mortar 1 .:4 (1 cement: 4 coarse sand ) CUM. 8.75 5017.90 43906.63

50 CODE NO 7335 Binding wire KG. 2063.42 46.00 94917.25

52 NS TurboVent Nos 30.000 4500 135000.00

53 NS Poly Carbonet sheet Nos 30.000 6500 195000.00

54 NS Down Take Pipe Nos 32.000 2000 64000.00

55 24.1.1.1 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge,upto 90 metre depth below ground level.:-All types of soil - 300 mm dia. Meter 90 486.80 43812.00

56 24.3.1 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.:-100 mm nominal size dia Meter 78 546.10 42595.80

57 24.4.1 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.:-100 mm nominal size dia Meter 12 573.10 6877.20

58 24.8 Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. cum 3.0 1,343.20 4029.60

59 24.12 Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. hour 3 916.80 2750.40

60 24.13.2 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of : 150 mm dia each 1 210.70 210.70

61 24.14.1 Providing and fixing 100 mm dia M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. each 1 1,448.40 1448.40

62 24.15.1 Providing and fixing 100 mm dia Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). each 1 228.30 228.30

63 NS Supplying all equipments, tools and installation of 1 HP single phase submersible motor pump set of KSB/ ISI make 2900 rpm capable of discharge 5000 LPH at 45 Mtr head with all necessary riser pipe, starter control panel, 1.25" Full way valve, 1.25" M.S clamp, 1.25" G.I Elbow, 1.25" check valve, 1.25" x 9" long G.I Nipple etc. all complete as per direction of E/I Each 1 26,446.00 26446.00 128398.400

PLUMBING AND SANITARY

64 12.80.2 Providing and fixing 110 mm dia unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. each 120.00 182.72 21926.40

65 17.1.1 Providing and fixining water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast iron P or S tap, 10 litre low white P.V.C. Flushing cistern with munally controlled device (handle level) conforming to IS : 7231 Parryware/Hindware with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.:-White Vitreous China Orissa pattern W C pan of size 580 x 440 mm with integral type foot rest. Each 4.00 4470.90 17883.60

66 17.3.1 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P . flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :-W.C. pan with ISI marked black solid plastic seat and lid Each 4.00 5504.30 22017.20

67 17.80 Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre &post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Each 2.00 6534.20 13068.40

68 17.6.1 roviding and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P .V .C.automatic flushing cistern, with fittings, standard size G.I. / PVCflush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P . brass coupling complete, including painting offittingsandcutting and making goodthewallsandfloors etc.wherever required :Single squatting plate with5litre P .V .C. automaticflushing cistern Each 2.00 5167.30 10334.60

69 17.7.4 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :-White Vitreous China Wash basin size 550x400 mm with 15 mm C.P. brass pillar taps. Each 5.00 2135.80 10679.00

70 17.28.2.1 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.:-Flexible pipe 32 mm dia Each 6.00 104.40 626.40

71 17.70.1 Providing and fixing PTMT Bottle Trap for Wash basin and sink.:-Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms. Each 10 325.10 3251.00

72 17.71 Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. each 6 146.30 877.80

73 17.73.2 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.:-600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. Each 3 424.00 1272.00

74 18.21.2.1 Providing and fixing uplasticised PVC connection pipe with brass ions :-45 cm length:-15 mm nominal bore Each 13 85.20 1107.60

75 18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.:-15 mm nominal bore Each 13 708.40 9209.20

76 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931.:-15 mm nominal bore Each 13 500.40 6505.20

77 17.32.2 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453 x 357 mm Each 3.00 857.00 2571.00

78 17.33 Providing and fixing 600 x 120 x 5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. Each 3.00 713.30 2139.90

79 18.9.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. 20 mm nominal outer dia Pipes meter 110.00 205.30 22583.00

80 18.8.1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I Concealed work including cutting chases and making good the wall etc. 15 mm nominal outer dia Pipes meter 98.00 278.20 27263.60

81 18.9.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm nominal inner dia Pipes meter 65.00 294.70 19155.50

82 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. per litre 1000.00 9.70 9700.00

83 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 Each 5.00 434.20 2171.00

84 18.52.1 Providing and fixing C.P. brass stop cock (concealed of standard design and of approved make conforming to IS : 8931 Each 5.00 594.80 2974.00

85 19.2.1 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 100 mm diameter S.W. pipe meter 45.00 404.30 18193.50

86 19.6.2 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete: 150 mm dia R.C.C. pipe meter 45.00 410.70 18481.50

87 19.27.1 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal gratingwith frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 30.00 3743.30 112299.00

88 19.30.1.1 Contructing brick masonry chamber for Underground C.I. Inspection Chamber and bend with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. Cover with frame (light duty) 455x610 mm internal dimentions, total weight of cover with frame to be not less than 38 kg. (weight of cover 23 kg. and weight of frame 15 kg.) RCC top slab with 1:1.5:3 mix (1 cement: 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 mix (1 cement:5 coarse sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm th. with cement mortar 1:3 (1cement:3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design. Inside dimensions 466x610 mm and 45cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 30.00 4266.80 128004.00

89 19.32.1 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with brick and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 1.00 33603.40 33603.40

90 19.34.2 Providing and fixing S.W. intercepting trap in manholes with stiff mixture of cement mortar 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 150 mm dia Each 4.00 429.60 1718.40

91 12.78.1 Providing and fixing on wall face unplastidsed PVC (working pressure 4 kgf per sqm) rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion.:-75 mm diameter. meter 25.00 162.70 4067.50

92 12.78.2 Providing and fixing on wall face unplastidsed PVC (working pressure 4 kgf per sqm) rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion.:-110 mm diameter. meter 76.00 257.50 19570.00

93 12.79.3.1 Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised - PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion each 30.00 141.60 4248.00

94 12.79.3.2 Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised - PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion:-110 x 110 x 110 mm dia Single tee with door each 25.00 193.40 4835.00

95 12.79.5.1 Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised - PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion:-75 mm dia Bend each 20.00 91.80 1836.00

96 12.79.5.2 Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised - PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion:-110 mm dia Bend each 35.00 132.00 4620.00

97 Code no. of 1354 (i) Rectangular cover 455x610 mm with frame (low duty) Each 1.00 1400.00 1400.00 #REF!

98 10.32.2 Steel work welded in built up sections/framed work including cutting hoisting, fixing in position and applying a priming coat of approved primer using structural steel, etc, as required in gtatings, frames, guard bars, ladders, railings, brackets gates and similar works KG 1764 114.60 202154.40

SUB-TOTAL 71202839.82

Sub-Total (without L.cess and GST) 62945910.73

99 Add difference of cost

Bricks Thousand 325.403 648.00 210861.14

100 Add Carriage cost of material

Local sand cum. 4129.51 216.10 892387.11

Coarse sand from kiul cum. 1204.78 3227.59 3888535.88

Coarse aggregate from Mirza Chauki cum. 2399.76 1574.65 3778782.08

Bricks Thousand 325.403 1668.20 542837.28

Work value without L.cess and without GST(A) 72316190.23

SF @10% of mineral cost(C) 691574.41

Sub-Total of (A+B+C) 73730926.54

Sub-Total 87002493.32

101 1.3.3 Wiring for light point/ fan point/ exhaust fan point/ Call bell Point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, with modular switch, modular plate, suitable size G.I box etc. as required. Group - 'C' Point 301 1146.00 344946.00

102 1.3.1 Wiring for light point/ fan point/ exhaust fan point/ Call bell Point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, with modular switch, modular plate, suitable size G.I box etc. as required. Group - 'A' Point 90 782.00 70380.00

103 1.5 Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed PVC conduit along with 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. Metre 1520 309.00 469680.00

104 1.7.1 Wiring for circuit/ submain wiring along with earth wire with the following sizes FRLS PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required.:-2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 2160 201.00 434160.00

105 1.7.2 Wiring for circuit/ submain wiring along with earth wire with the following sizes FRLS PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required.:-2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire (for 3X5A socket Point) Metre 1400 246.00 344400.00

106 1.7.3 Wiring for circuit/ submain wiring along with earth wire with the following sizes FRLS PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required.:-2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 300 309.00 92700.00

107 1.7.4 Wiring for circuit/ submain wiring along with earth wire with the following sizes FRLS PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required.:-2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 700 422.00 295400.00

108 1.7.11 Wiring for circuit/ submain wiring along with earth wire with the following sizes FRLS PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required.:-4 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 740 660.00 488400.00

109 1.24.1 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (for On switch board):-5/6 amps switch Each 125 82.00 10250.00

110 1.24.4 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (for On switch board):-3 pin, 5/6 amps socket outlet Each 125 112.00 14000.00

111 1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular switch box including connection but excluding modular plate etc. as required. Each 156 358.00 55848.00

112 1.32 Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch connection, painting etc, as required. Each 125 531.00 66375.00

113 1.33 Supplying and fixing 2 pin, 5 amp. ceiling rose on the existing junction box/PVC box including connection etc as required. Each 448 64.00 28672.00

114 1.34 Supplying and fixing batten/angle holder including connection etc. as required. Each 288 80.00 23040.00

115 1.37 Supplying and fixing Ding-Dong call bell suitable for single phase, 230 volts complete as required. Each 15 240.00 3600.00

116 1.27.1 Supplying and fixing following modules G.I. box along with modular base and cover plate for modular switches in recess etc as required.:-1 or 2 module (75mm X 75mm) Each 300 234.00 70200.00

117 1.53 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 amps modular socket outlet and 25 amp modular SP MCB 'C' curve, including connections, painting etc. as required. Each 25 683.00 17075.00

118 1.56 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 nos. 5 pin 5/6 amps modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc. as required. Each 135 778.00 105030.00

119 2.8.7 Supplying and fixing following way single pole & neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus-bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator):-12 way, Double door each 25 2314.00 57850.00

120 2.9.1 Supplying and fixing following way three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB / RCCB / Isolator):-4 way ( 4 + 12 ), double door, horizontal type each 25 4184.00 104600.00

121 2.12.1 Supplying and fixing following rating, 240 volts, ‘C’ series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.:-6A to 32A amps, single pole Each 500 237.00 118500.00

122 2.12.6 Supplying and fixing following rating, 240 volts, ‘C’ series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. :-40A to 63A amps, SPN Each 50 1233.00 61650.00

123 2.12.8 Supplying and fixing following rating, 240 volts, ‘C’ series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. :-40A to 63A amps, TPN Each 50 2329.00 116450.00

124 2.4.2 Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required.:-125 A, 36 KA, FPMCCB Each 5 8676.00 43380.00

125 2.7.3 Providing and fixing following capacity 4 pole On-load/panel mounted changeover switches in existing cubicle panel board, making connection, earthing the body etc. as required.:-100A Each 5 9334.00 46670.00

126 2.34.1 Supplying and fixing following ways, surface/recess mounting / vertical three phase distribution board (VTPN DB'S) of CRCA SHEET STEEL, dust protection, duly powder painted suitable for upto 250 amp , four pole MCCB'S etc. as per required. Four way, Double door, I/C 250 A MCCB EACH 5 19610.00 98050.00

127 8.11 Supply and fixing of fabricated Electrical control panel of cubical construction, floor/wall mounted type, fabricated out of 16 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator and complete in all respect etc and panel manufactures must be approved by CPRI. (But without RYB inicator, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears etc.) sq.ft. 30 1809.00 54270.00

128 8.13 Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required. Each 4 6536.00 26144.00

129 5.1 Supplying and fixing 4'X18 watt LED batten with minimum efficacy 100 lm/w in polycarbonate housing and complete with integrated electronic driver etc directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required. Each 270 521.00 140670.00

130 5.8.2 Supplying and fixing surface mounted following types LED downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.:-15 watt Each 110 1608.00 176880.00

131 5.10 Supplying and fixing 10/12 watt LED type Bulk-head luminaire with minimum efficacy 100 lm/w in comprising of pressure die cast housing, acrylic diffuser,IP 65 protection and complete with integrated electronic driver etc directly on wall/ceiling including connections with 1.5 sq. mm FRLS PVC insulated copper conductor cable etc as required. Each 36 1275.00 45900.00

132 5.15.7 Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, IP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.:-200 watt Each 12 10495.00 125940.00

133 5.15.4 Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, IP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.:-100 watt Each 35 6085.00 212975.00

134 6.1.4 Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required.:-9/10 watt LED lamp Each 280 161.00 45080.00

135 8.15 Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 210 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required. Each 170 2482.00 421940.00

136 8.17.1 Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required.:-300 mm sweep Each 20 2572.00 51440.00

137 8.18.2 Supply and fixing of following sweep/ sizes PVC/ABS square body Exhaust Fan with automatic openable louvre shutter in existing opening including making connection, testing etc as required.:-200 mm sweep (1300/1400 RPM) Each 15 2074.00 31110.00

138 8.5 Supplying and fixing of 32 mm dia X 1.00 metres long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV/ HPSV/ LED street light fitting on pole including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required. Each 60 1038.00 62280.00

139 7.7.9 Supply of following sizes and core XLPE/PVC insulated PVC sheathed (Heavy duty) armoured electric cable with aluminium conductor for working voltage upto 1.1 KV as required.:-50 sq.mm, 3.5 core Metre 400 561.00 224400.00

140 7.1.2 Laying of one number PVC insulated and PVC sheathed/ XLPE power cble of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.:-Above 35 sq. mm and upto 95 sq. mm Metre 450 326.00 146700.00

141 3.21 Providing chemical/mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth and earth inspection pit etc. as required. Set 10 16675.00 166750.00

142 3.17 Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc as required. Metre 100 144.00 14400.00

143 7.9.2 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required.:-4 X 16 sq. mm Metre 20 1018.00 20360.00

144 7.9.3 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required.:-4 X 25 sq. mm Metre 15 1881.00 28215.00

FOR LIGHTNING ARRESTER

145 4.2 Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required. Each 20 416.00 8320.00 6,169,633.00

146 4.4 Jointing copper/ G.I. tape ( with another copper/ G I tape, base of the finial or any other metallic object ) by riverting/ nut bolting sweating and soldering etc. as required. Each 100 81.00 8100.00

147 4.7 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For horizontal run) Metre 400 102.00 40800.00

148 4.8 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For vertical run) Metre 150 145.00 21750.00 6,169,633.00

149 3.2 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal/coke and salt as required. Set 10 6323.00 63230.00

150 3.9 Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including connection/ termination with GI nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm) Metre 100 133.00 13300.00 SUM

151 8.18.3 Supply and fixing of following sweep/ size pvc/ abs square body exhaust fan with automatic etc as per required 250 mm sweep (1300/1400 RPM) each 6 2288.00 13728.00

152 8.2 Supply and installation of 600 mm , 230V A.C wall mounted, heavy duty fan including fixing the brackets etc. as per required. each 25 9941.00 248525.00

153 8.16 Suply and installation of regular/standard model A.C ceiling fan of 1400 mm sweep with service etc. as per required each 40 2838.00 113520.00

154 5.5 Suply and fixing replacable compact commercial batton suitable for double T8 LED tube complete with 24 W LED etc. as per required each 50 1232.00 61600.00

155 NS ISI Marked ( IS. 2878 ) Fire extinguisher, corbon di oxide type capacity 4.5 kg flat base including valve, discharge hose of not less than 10 mm dia. 1 m long and complete in all respect including initial fill with co2 gas conforming to IS: 307 - 1966 filled to a filling rate of not more than 0.667 and wall suspension bracket. comulative 7 15014.00 15014.00

ABC ( Powder type ) fire extinguiser, in HP Mild steel cylinder ISI marked TAC approved fitted with pressure indicating guage internal tube, squeeze lever type valve fully charged with ABC powder ( mono Ammonium phosphate ) pressure by nitrogen complete in all respect including wall suspension bracket and conforming to IS: 1349 -1993 10KG :- 10

156 NS Fire Fighting Pump, Jockey Pump & Diesel Fire fighting Pump each one piece(1+1+1) comulative 1 421562.00 421562.00

157 NS Fire Hause - 30 m Nos 5 7830.00 39150.00

158 NS Fire Alarm System Nos 8 16500.00 132000.00

159 NS Fire Hydrant System & Pipes Nos 1 210000.00 210000.00

160 NS Fire Buckets and Stand Nos 24 272.00 6528.00

161 NS WEIGH BRIDGE(30 TONNE CAPACITY) Nos 1 650000 650000.00

162 NS CONVEYOR BELTS SYSTEM(Conveyor belt length in meter) Nos 1 5834000 5834000.00

163 NS TROMMEL(08 TPH) Nos 1 2000000 2000000.00

164 NS MAGNETIC SEPARATOR(Separation of ferrous material from municipal solid waste) Nos 1 1669000 1669000.00

165 NS AIR BLOWER(1500 CFM AND 2900 RPM) Nos 3 76000 228000.00

166 NS BALER MACHINE(40 TONNE (JACK FORCE) Nos 2 450000 900000.00

167 NS SHREDDER(02 TPH) Nos 1 3000000 3000000.00

168 NS TRACTOR WITH LOADER(40 HP ( 3 CYCLINDER)) Nos 1 875000 875000.00

169 NS ELECTRIC FORK LIFT(1500 KG) Nos 1 800000 800000.00

170 NS STORAGE BINS(1000 LITRE) Nos 83 30000 2490000.00

171 NS WHEEL BARROWS(140 LITRE VOLUME) Nos 9 3700 33300.00

GRAND TOTAL 112475680