Construction of Drug Ware House at Anantnag (Balance work, Finishing Work and Sanitary Work)

Amount

Earth work in excavation by manual/mechanical means in foundation trenches or drains (not exceeding 1.5M in width as well as 10Sqm on plan/over areas (exceeding 30 cm and upto 1.5 m in depth,1.5 m in width as well as 10 sqm on plan ) including dressing of sides ramming of bottoms lift up to 1.5M including getting out the excavated soil and disposal of surplus excavated soil within a lead of 5km from site /edge cutting or as directed by EIC. disposed earth to be leveled and neatly dressed in all kinds of soil including pumping out water caused by springs,tidal or river seepage,broken water means or drains and the like complete during execution of work.

Providing and laying of stone soling hand packed dry including all carriage and cost of material involved complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work up to plinth level 1:4:8 (1Cement: 4 coarse sand: 8 grade stone aggregate 40mm nominal size) (crushed) including all carriages and cost of material involved.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work up to plinth level 1:2:4 (1Cement: 2 coarse sand: 4 grade stone aggregate 20mm nominal size) (crushed) including all carriages and cost of material involved.

Reinforced cement concrete work in walls (any thickness),including attached pilasters,buttresses,plinth and string courses,fillets,columns,pillars,piers,abutments,posts,suspended floors,stairs and sturts,etc upto floor five level excluding cost of centring,shuttering,finishing and reinforcement in 1:1.5:3 (1 cement:1.5 cooarse sand:3 graded crushed stone aggregate 20 mm nominal size) including all carriages complete.

Reinforcement for RCC works including straightening, cutting, bending placing in position and binding all complete. Thermo Mechanically Treated bars. including all carriages .

Centering and shuttering including strutting, propping etc. and removal of form for suspended floors,walls,columns,plinth etc using 12 mm ply including all carriages.

Brick work with common burnt clay FPS non modular bricks of class designation 75 upto floor V level in cement mortar 1:6 (1 cement :6 coarse sand) including all carriages.

P/F in position 12mm thick imported panellig on walls,ceiling including cost of necessary adhesive & cost of nails etc.complete job. incl preparing the surface for final finish and touch wood polish on the sealer surface all complete including cost of frame work with wooden scants and cost of nails complete including all carriages.

Providing and fixing of 4 mm thick ACP of approved brand/shade including all required almunium framework for eaves boardingand soffits and all scaffolding charge,carriages etc complete

Providing & Fixing of 65x65 mm/2 thick wooden cornice of budloo wood incl. all carriages complete.

15 mm Cement plaster on the rough side of single or half brick wall of mix: 1:6(1 cement:6 coarse sand) including all carriages complete.

Cement concrete flooring 1:2:4 ( 1cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. Complete. 50 thick with 20mm nominal size stone aggregate(Crushed) including all carriages complete

Providing and applying white cement based putty (Birla or equivalent )of 2mm thickness over plastered surface to prepare the surface even and smooth including all carriages complete

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work including applying cement primer of approved brand and manufcature on walls surfaces and all carriages complete.

Providing and fixing Ist qualityCeramic glazed wall and floor tiles confirming to IS : 13753 of approved make like NITCO, ORIENT, KAJARIA, SOMANY or equivalent make in all colour shades of any size (as approved by Engineer in charge) cement Mortar 1:3(1 cement:3 coarse sand) and jointing with grey cement slurry @3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade (size of tile as specified by the site Engineer) including all carriages complete

Providing and fixing gang saw cut mirror polished (premoulded and pre polished), machine cut for kitchen platform, vanity counters window sills,floors facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing and polishing to edge to give high gloss finish etc. complete at all levels Granite of any colour and shade (Area of slab upto or over 0.5 sqm) 16-18 mm thick including all carriages complete.

Providing double edge moulding to 18 mm thick granite stone counters,vanities etc including machine polishing to edge to give high gloss finish etc.complete as per design as approved by Engineer-in-Charge

Providing and fixing of 2 feet deep almirahs/overhead almirahs/wardrobes etc made up of 19 mm thick superior quality water resistant ply board with external lining of mica duely fixed with adhesive,fixing of 12 mm ply on back side,making of requisite number of drawers and shelves in each almirah/wardrobe, wooden panelled/glazed or 19 mm ply board shutters with mica on front side,providing and fixing of 19 mm wooden beading on all sides including providing/ fixing of fixtures i.e; paino type hinges,handles ,locking devices (link),catches,knobs,latches etc complete as per the architectural drawings and directions of engineer in charge (finished work to be paid as per face measurement only )

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions, at top, bottom and sides with required EPRM rubber/ neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) For fixed portion/shutters of doors,windows and ventillators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required. Powder coated Almunium (minimum thickness of powder coated of 50 microns) Jindal or equivalent make including all carriages.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions, at top, bottom and sides with required EPRM rubber/ neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) .For wireguaze shutters of doors,windows and other shutters including providing/fixing of hinges/pivot and other fittings as required and GI wire guaze complete

Providing and fixing glazing in aluminium door,window,ventillator shutters and partitions etc.with EPDM rubber/neoprene gasket etc.complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of almunium snap beading shall be paid in basic item) With floating glass panes of 5.5 mm thickness (weight not less than 13.50 kg/sqm) including all carriages.

Providing and fixing in position collapsible steel shutters with vertical channels 20* 10*2 mm and braced with flat iron diagonals 20*5 mm size with top and bottom rail of T-iron 40*40*6 mm with 40 mm dia, steel pulleys complete with bolts,nuts,lockingarrangement,stoppers,handles, including a priming coat of approved steel primer including all carriages

Providing and fixing of steel racks of approved brand/shade of 2 ft depth Required dimensions and designs as per the requirements /directions of the concerned authority.

Providing and fixing of PVC Soil/Waste/Ventialaing pipes of prince or equivalent make of the following size:

75 mm dia

100 mm dia

Providing and fixing of PVC pipe fittings of Prince/Phenolex or equivalent make of following size to soil/waste/ventellating pipes as directed by the site Engineer including all carriages.

100 mm dia door tee

100mm dia P/S trap

100 mm dia collar

100 mm dia door bend

100 mm dia plain bend

75 mm dia collar

75 mm dia Floor trap

75 mm dia plain bend

Stays and clamps

Providing and fixing of GI pipe lines to walls/ceilings/floors (Light grade of specified mass )Prakash Surya /Jindal or equivalent including jointing,testing and making good the surface as directed by the site engineer including all carriages complete job

15 mm dia

20 mm dia

Providing and fixing GI pipe fittings of specified brand (ISI mark UNIK/Nike/Prince or equivalent including testing and commissioning and all carriages complete.

15 mm dia elbow

15 mm dia Tee

15 mm dia Nipples 2"-6"

15 mm dia union

15 mm Gate/Ball value

20 mm Tank nipple

20 mm dia elbow

20 mm Tee

20 mm dia nipple 2"-6"

20 mm dia union

Ball/Gate value 20 mm

Providing and fixing water closet squatting pan ( Indiantype W.C. pan) with 100 mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing cistern (of approved make) with manually controlled device (handle lever) conforming to IS:7231, with all fittings C.I/M.S. brackets, 32mm diameter flush pipe with fittings and clamps, over flow arrangement with specials and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required white vitereous china W.C. pan of size 580 mm including carriages(Hindustan or equivalent)

Constructing brick masonry manholes of size 18"*18" in cement mortar1:4 ( 1 cement : 4 coarse sand) , foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finsihed with a floating coat of neat cement complete as per standard design including PVC frame with cover complete job including all carriages and costs.

Providing and fixing of 50 ltr water heater gyser (Venus/Recold/Jaguar or equivalent make including nuts and bolts and necessary fittings including all carriages complete job.

Providing and fixing of CP fixtures of Jaguar /Hindware /Cera / Essel/Parko or equivalent make including jointing testing and making good to surface as directed by the site Engineer including all carriages.

Soap case

Angle value

Central hole basin mixer

Wall mixer

Sink mixer

Long body Bib cock

Grating with hinge type

15 mm dia 2"-4" Nipples

CP Connection 18'

Steel Sink 24"X18"

CP waste pipe

CP waste coupling

Mirror

Providing and fixing wash basin with pedastal (Jaguar/Hindware/Cera/Essal or equivalent) and making good the walls wherever required white vitrous china washbasin size 630*450 including all carriages

Providing and placing on terrrace (at all floor levels) polyethene water storage tank ISI:12701 marked indicating the BIS License No with cover and suitable locking arrangement and making necessary holes for inlet,outlet and overflow pipes but without fittings and base support for tank(Sintex,Electroplat,Star,Lotus or equivalent having valid ISI license) including all carriages.

Providing and fixing in positon 2 HP water motar of standard quality (Crompton/KIRLOSKAR/Havells or equivalent make including necessary fittings as directed by the site engineer including all carriages complete.

Providing and fixing of Almunium hardware fittings to doors and windows of approved quality (ISI mark) approved by the site Engineer including all carriages.

Tower bolts 4"

Tower bolt 6"

Handles 4"

Handles 6"

L-Drop 12"

Link locks

Wind hooks

Carriage

Sand for 40 kms

Stone aggregate 60 kms

Brick 100 km

NISAR AHMED SHEIKH

MALIK BUILDERS

ABDUL HAMID MIR