Cable Laying work along patrolling track for boundary wall lights from Ayodhya Marg Main Gate to AFLE Building of HAL

Laying of one number 4 Core, 16 Sqmm, PVC insulated and PVC sheathed / XLPE, Armoured power cable of 1.1 KV grade of following size direct in ground including excavation not less than 900 mm, sand cushioning, protective covering as per standard and refilling the trench or conceiled on wall etc as required at site.

a) Size of cable 4 core x 16 sqmm

Supply of PVC insulated and PVC sheathed / XLPE Armoured LT power cable of 1.1 KV grade of following size of cable. 1. Size of cable 4 Core X 16 Sqmm Make: - Universal/RPG/Finolex/Grandlay/ Polycab only.

Supply of LED Street light fixture, warm white/Moon light type. 20 W powder coated pressure die cast aluminium body (System lumen efficacy ≥105 <120 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driveras per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 48 DELHI SCHEDULE OF RATES (E&M)-2025 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70,under voltage and over voltage protection, EMIEMC As per CISPR -15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin),SDCM (Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output.LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).

Supplying and fixing of 4 way, horizontal type three pole and neutral, Water Proof Poly Carbonate, MCB distribution board, 415 V, on surface/Conceiled in wall, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, including earthing etc. as required , suitable for incorporating MCB's, 4 way per phase with following incoming and out goings MCB's. Make:- Hensel/MDS/Havells/L&T/ Crompton/HPL/Standard / Seimens make Incoming-63/60Amps, TPN Isolator,:MCB-01 No., Outgoings: a) 16 Amps S.P. MCB – 5 Nos. b) 20 Amps SP, MCB – 7 Nos. The work shall be done as per direction of EIC.

Supplying and fixing of 6 way, single pole and neutral, double door MCB DB, Poly Carbonate, Water Proof, MCB distribution board, 240 V, on surface/ Conceiled, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, including earthing etc. as required. (But without MCB/RCCB/Isolator) , suitable for incorporating MCB's, with following incoming and out goings MCB's. Make:- Hensel/MDS/Havells/L&T/ HPL/Standard / Seimens make Incoming-40 Amps, DP Isolator,:MCB-01 No., Outgoings: a) 16 Amps S.P. MCB – 2 Nos. The work shall be done as per direction of EIC.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. . The sizes of cable as detailed below:

a) Size of cable 4 core x 16 sqmm

Supply & Installation of feeder pillar box outdoor type double door , vermin and weather proof made out of 14 SWG thick CRCA sheet including canopy type roof 15 cm extended in all side and two part hinged door in front side with knobs closing the front side door gasket arrangement and back side fixed with Nut, bolts and gasket, including provision of one set of aluminium busbar 400A rating for phase and 240 A for neutral fixed on DMC/SMC insulator with RYB Black colour code with heat shrinkable PVC sleeves and holes in bus bar strip and provision of suitable cable gland for cable entry including two coat of powder quoted paint complete and installation on PCC foundation with following: 1. Incoming:- Switch Fuse unit 250A rating with HRC fuses Knife Type Make: L&T/Siemens - 01 Nos 2. Outgoing: 32/63 Amp HN Type Fuse Fitting L&T/Siemens - 06 Nos per Phase 3. Phase indicating lamps for RYB on Each incomming/outgoing 5. Voltmeter(0-500v) & Ammeter (0-200A) on each incomming/outgoing 6. Digital Multi Function Meter of Make: L&T/Essen/AE/Rishab/Siemens Note: Drawing of feeder pillar shall be get approved before fabrication work and making of foundation for installation work is in the scope of supplier. Work is to be done as per the direction of Engineer- In-Charge.

Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.

Supply of 06 watt warm white, 3000K, Efficacy 130 lumen per watt outdoor, spot light with spike stand , IP Protection 65 of any standard make with warranty of one year.

LED rope light Tri Colour, wattage 10 W per meter, No of LED,s per meter, Efficacy 130 lumen per watt, Transperent Body Material, Close with END Cap, IP Protection 65 of length 18-20 mtrs with LED driver 02 nos with each set, Warranty of supplied item shall be for one year.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm) as required.

Sub-Total

Discount on Sub-Total (if any)

Sub-Total after Discount

Net Total (Including GST)

Note: i. Please refer Chapter 6(B) of Technical Bid document for recommended make of equipments to be used in the project, if it is not specifically mentioned in the price bid.

HINDUSTAN AERONAUTICS LIMITED ACCESSORIES DIVISION, LUCKNOW PQ FORM/ELIGIBILITY CRITERION-MATRIX

NAME OF THE WORK: "Cable Laying work along patrolling track for boundary wall lights from Ayodhya Marg Main Gate to AFLE Building of HAL"

Estimated Cost (in Rs.)

PART-A: Desirable Criteria

Name of the Individual / Firm / Company: * Mandatory

Type of ownership Pvt. Ltd./ Proprietorship/Partnership/ Public limited/ Govt. Agencies/ Trust If Other, please specify

Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc.,

Registration with HAL/ other organization if any

Address of Correspondence:

Contact Details: Contact person name: Designation: Mobile No:. Ph. No. with STD code: Email Id :

Contractor must give his acceptance to provide services as per ‘Requirement, Scope of work, Drawings’ and ‘Terms & Conditions' contained in Technical Bid.

Self attested copy of PAN Registration certificate issued by income tax authority.

PART-B: Essential Criteria

PART-C: Declaration

DECLARATION I

The document being viewed / downloaded from the website and having read & understood all the contents of the tender document mentioned under terms and conditions including price bid do hereby accept all the terms and conditions laid down in the said Tender document and will abide by the same on acceptance and ward of work.

DECLARATION II

I/We declare and confirm that - 1. All information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my offer . 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I / We aware that document sought only be uploaded for evaluation of offer. 5.I/We are not debarred / blacklisted from any Govt agencies, if debars for specified period reason for debar and copy of resumption of same shall be provided. 6. I/We have not concealed any information which may adversely effect my qualification.

DECLARATION III

I/We declare and confirm that all the documents related to NIT mentioned at Technical Bid Document Sl.No.2 and 3 have been attached with the technical bid.

Name of Bidder:

* 1. To be filled by Bidder essentially and carefully. Supporting documents must be attached as proof. Clarifications shall be sought w.r.t. information provided with tender documents. 2. Similar works implied that works related to HT/LT Cable Laying Electrical Works in nature. Mere supply of electrical goods does not mean qulification in the tender. 3. Scanned copy of completed work orders and completion certificate issued by respective clients to be attached. If the completion certificate is form private organization the same shall be uploaded with TDS certificate. 4. The work shall be completed as a whole, Partial value/completion will not be considered. 5. The Bidders are requested to attach scan copies of all the relevant / desired / required proofs/ documents on e-portal, failing which tender shall be summarily rejected without assigning any reason to bidders.