SPECIAL REPAIR TO BLDG NOs T-23, T-24A AND CERTAIN MINOR WORKS AT DINJAN MIL STN UNDER GE DINJAN

Amount

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs of any thickness including cover fillets complete all as directed.

M&L for anodised aluminium snap grid size 605 X 605 mm frame work for false ceiling complete all as specified and as directed.

S&F for hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed.

M&L for 4 mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws including two coats of distemper oil emulsion on surface of ceiling/boards etc complete all as specified and as directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position of unframed work, complete all as specified and directed.

Dismantling timber works in fillets, rail, post, rafter, purlins etc under 40 Sq.cm in section (unframed work), in any position complete all as specified and as directed.

Dismantling boarding, any discription, fixed in any position complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe 410 -W (Gde- E- 250) quality- A complete all as specified and as directed.

M&L Rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete ; steel confirming to Fe-410-W(Gde E-250), quality 'B' all as specified and as directed.

M&L for preparing of new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old painted surfaces of wooden surface of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old wooden surfaces of any description, not exceeding 10 cm width or girth when unconnected with other painting or when painted in different tint and applying one coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for second class hardwood plain fillets. square, rectanglular or triangular in section, clean swqn, secured with nails or bands size exc 6Sq cm and n. exc 13 Sq cm complete all as specified and as directed. .

M&L for second class hardwood, scantlings, wrought, timber framed and fixed complete all as specified and as directed.

S&F 25 mm thick, second class hard wood boarding, clean sawn, (except flooring and skirting) planed one side and edges tongued and grooved or rebated and fixed with nails in any situation etc complete all as specified and directed.

M&L preparing new or previously untreated surfaces of wood and wood based Materials of any description and girth and treated with two coats of creosote oil, complete all as specified and as directed.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as specified and as directed. (One Side only measured in cases where both sides are Plastered), complete all as specified and as directed.

M&L for GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste fixed with tinned tacks of wire staples complete all as specified and as directed.

M&L for rendering 18 mm thick (12+6) externally one side of lathing in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement, mixed with integral water proofing compound @ 2% by weight of cement on top layer surface complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

M&L for rendering 12 mm thick on one side of lathing in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

Demolition of brick work in cement mortar incl all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 meter mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with sub class 'B' burnt clay bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

Taking down cement plaster or lime plaster on walls /ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retreived debris as directed including necessary scaffoldings etc complete all as directed

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:6) and finished surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10 mm thick of internal wall on fair faces of brick work or concrete surfaces in cement mortar in (1:6) and finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls, etc and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of external walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation old decorated plastered or unplastered surfaces by brooming down or steel wire brushing, scraping down, the surfaces covered by smoke soot, growth of moulds and moss, efflorescent, having oil and greases spots and applying one coat of oil bound distemper complete all as specified and as directed.

M&L for preparation old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing, scraping down, the surfaces covered by smoke soot, growth of moulds and moss, efflorescent, having oil and greases spots and applying one coat of cement base paint complete all as specified and as directed.

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) removing rubbish off the premises etc complete all as directed

M&L for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in sub-base of floors, plinth protection etc. finished the surface of concrete fair, even and smooth without using extra cement, complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating (AZ-150) GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified and directed.

Dismantling floor hearth or wall tiling and stone slabs including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises etc complete all as directed

M&L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, including 15 mm thick screed bed or bedding in cement mortor (1:6) and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and as directed.

M&L for coloured 450x350x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick rendering as backing coat in cement mortar (1:4), complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exceeding 1.50 Sqm each complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from frames) exceeding 1.5 Sqm but not exceeding 4.0 Sqm each complete all as directed.

S&F pressed steel frames for doors local work shop made of size 105x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

S&F pressed steel frames for doors local work shop made of size 125x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

S&F 35 mm thick, second class hard wood, glazed and skeleton shutters with open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut mitered beads for securing glass, etc, sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24 (a).

S&F 30 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitered and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded as in SSR Part I Section 8 clause 8.24 (b) complete all as specified and as directed..

S&F 35 mm thick second class hard wood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed.

Hacking out of old broken glass any thickness, size, quality or description, from metal frame including punching or drilling out old glazing pins/springs clips and providing and fixing new ones and removal of demolished materials from site complete all as specified and directed.

S&F 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n.exceeding 0.50sqm in each pane , complete all as specified and directed.

S&F for 4mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F Stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F for 75mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F for 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F for 150 mm long, aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and as directed.

S&F for 100 mm long, aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and as directed.

S&F 150 mm size aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and as directed.

S&F 100 mm size aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and as directed.

S&F 300mm long aluminium alloy anodised sliding door bolts, with haps and staples (bolt type) and fixing clips of sheet, cast oions or cast aluminium alloy and fixed. with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed

M&L for PCC (1:2:4), type B0 ( using 12.5 mm graded aggregate) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, hold fast, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs,, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

S&F in repairs vitreous china wash basin, size 550x400mm, white, flat back, with 32mm bore PVC (HDPE) waste pipe 450mm long, 32mm bore CP waste coupling, chain, plug and porcelain stopper & brackets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and as directed.

S&F 15 mm bore, bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F in repairs 15 mm bore, bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F 15mm dia angular stop cock with flange, cast copper alloy, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repairs 15 mm bore dia cast copper alloy fancy type, chromium plated stop valves, crewed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repair 15mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and as directed.

S&F in repair towel rail, 600mm long, PTMT fixed with and incuding chromium plated brass screw down and wooden plastic cleat (minimum weight 190 gms) complete all as specified and as directed.

Taking up or down steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc for 15 mm bore pipe complete including stacking aside for reuse and removal of unserviceable items from site complete.

Taking up or down steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc for 20 mm bore pipe complete including stacking aside for reuse and removal of unserviceable items from site complete.

M&L for steel water tubng 15mm bore, galvanised, medium grade with all fitting and fixture to be fixed to walls and ceilings or laid in floors, duly clamped complete all as specified and as directed.

M&L for steel water tubng 20mm bore, galvanised, medium grade with all fitting and fixture to befixed to walls and ceilings or laid in floors, duly clamped complete all as specified and as directed.

S&F in repair 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe including 20 mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (minimum weight 20 mm - 210 gms ) complete all as specified and as directed.

S&F for 15mm bore gun metal gate valve with iron wheel head, screwed both ends for iron pipe or for unions complete all as specified and as directed.

M&L for 75 mm thick cement concrete (1:4:8 ), type D-2, (40mm graded aggregate) in sub base of floor etc complete all as specified and as directed.

M&L for prepolished, chequered cement concrete tiles of size 25cmx25cmx22mm thick, as in floors etc, including 20 mm thick screed bed or bedding in cement mortar (1:6) and set and jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and flushing pipe, anti syphonic pipe with PVC seat and cover complete but excluding flushing cistern & flush pipe including making good to disturbed surfaces of floor using concrete (1:4:8) type D2 and to match with existing specifications complete all as specified and as directed.

S&F in repairs PVC low level flushing cistern, 10 litre capacity, valveless, symphonic action type with inlet, ball valve, float and handle incl bracket, PVC conection pipe and flush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specified and directed

S&F in repair CP health faucet cast copper alloy with push button & 1m long flexible steel pipe with PVC lining suitable for 15mm bore pipe complete all as specified and directed.

S&F in reparis Mild steel 300 mm, ordinary rat rail rod pattern springs including roller and roller plate complete and fixed complete all as specified and directed.

S&F 150 mm Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed to door and fixed in repairs

S&F for aluminium (extruded section body) door closer hydraulically regulated, designation No.3, universal type suitable for shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed.

M&L for annodised powder coated aluminium frame for doors,windows, ventilators and partition with one or more rebates including joining cleat for fixing etc.with power coating complete all as specified.

S&F Anodised aluminium door shutters, aluminium section weighing 0.55 Kg/Sqm incl necessary jointing cleats, glazing clips, rubber neophrene packing, handles 02 Nos in each doors, hinges, aluminium snap beadings, screws,etc, incl powder coating to a minimum thickness of powder coating 50 microns complete as specified

S&F Anodised aluminium powder coating windows and ventilator shutters, (minimum thickness of powder coating 50 micron) side hung type without sash aluminium sections weighing 0.55 kg/m rubber including necessary joining cleats, glazing clips, rudder packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long hinges type B-2 100mm long - 02 Nos, suitable handle - 1 No complete all as specified and directed by E-in-charge.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at Junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Chief.

M&L for 12 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with screws to timber frame work including teakwood lipping 6 mm thick fixed with nails including taking down old unserviceable complete all as specified and directed. .

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep for foundation/cable trench, not exceeding 10Sqm on plan and getting out in soft/loose soil complete all as specified and as directed.

Excavating in trenches exc 1.50 mtr wide and exc 1.5 m but n. exc. 3.0 mtr in depth for foundation/cable trench, not exceeding 10Sqm on plan and getting out in soft/loose soil complete all as specified and as directed.

Returning filling including spreading, levelling and well ramming in layers not exceeding 25cm thick in soil complete all as specified and as directed.

Removal of surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M&L for plain cement concrete (1:4:8), type D2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for plain cement concrete (1:2:4), type B2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for Birckwork with sub class B brick in one brick thick honey comb work built in CM (1:4) complete all as specified.

M&L for rendering 20 mm thick on fair faces of external wall of brick work or stone surfaces in two layers (10 mm and 5 mm thick) in cement mortar (1:4) using water proofing compound in top layer and finished even and smooth without using extra cement complete all as specified and directed. Note:(water proofing compound measured as separately)

Supply only Water Proofing Compound of approved make.

M&L for PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in surface chanels and drains .

M&L for reinforced cement concrete type B-0 (1:2:4) (using 12.5 mm graded stone aggregate) as Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses, etc complete all as specified and as directed.

M&L for Reinforced Cement Concrete 1:2:4, type B-1 (Using 20 mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc complete all as specified and directed. (Note : reinforcement shall be measured and paid separately against respective item).

M&L for RCC (1:2:4) (nominal mix ) type B1 (20 mm graded aggregate) in foundations, including rafts, footings, foundation beams ; plinth beams; bases for columns, etc ; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC (1:2:4) (Nominal Mix) type B1 (20 mm graded aggregare) in column, pillars, piers, posts and strut complete all as specified and as directed.

M&L for RCC (1:2:4) (nominal mix ) type B1 (20 mm graded aggregate) in Beams, cantilevers, bressummer, lintels over 1.5 span complete all as specified and directed.

Use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc rough finished flat surface of concrete complete all as specified and as directed.

Use and waste form work flats sides to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work ; not exc 200 mm thick (Horizontal or sloping) complete all as specified and directed.

Use and waste form work to sides of pillars, posts, struts, piers, columns and stanchions etc rough finished flat surface of concrete complete all as specified and as directed.

Use and waste form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter of flat rough finished surfaces of concrete complete all as specified and as directed.

Use and waste form work to flat faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter

M&L for precast reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in cover slab of drain, manhole etc and set in cement mortar (1:4) including necessary formwork, moulds, etc complete all as specified and as directed. Note : Reinforcement shall be measured and paid separately.

M&L for mild steel TMT bars 10 mm dia and over ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for mild steel TMT bars 6mm to 08 mm dia,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

S&F TMT reinforcement bar, conforming to Fe-500, 5mm dia and upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as binding with and including mild steel wire (Annealed) not less than 0.9mm dia or securing with clips all as specified.

M&L for Loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F for 110 mm bore PVC (SWR) bends of any radius complete all as specified and as directed.

S&F for 110 mm bore, PVC (SWR) vent cowl fixed with solvent cement complete all as specified and as directed.

M&L for plain cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggragate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 110 mm bore pipes complete all as specified and as directed .

Surface excavation n.exc 30 cm deep and averaging 15 cm deep & getting out in soft / loose soil all as specified

M&L for hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface with broken stone or boulders complete all as specified and as directed.

M&L for 100mm thick PCC 1:4:8, type D2 (using 40mm graded crushed stone aggregated) as in sub base of floor complete all as specified.

M&L for 60 mm thick, M-35 machine pressed precast concrete interlocking paver block of any size and shape conforming to IS 15658-2006 and jointed with white cement and pigment

Excavating in post holes (or similar holes) each n.exc 0.5 Cum , getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layer n.exc 25 cm, watering, and removing surplus soil to a distance n.exc 50 mtr and making good surfaces in hard standing or hard/dense soil complete all as specified and as directed.

S&F Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates and other similar items conforming to Fe-410 Gde E-240 complete all as specified and as directed

M&L for Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and directed.

M&L for preparing of new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm (nominal area), FRLSH PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including PVC casing caping with all fittings and accessories of PVC casing caping (like Tee, bend etc.) complete fixed to walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLSH PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point including PVC terminal box (sunken type) with 3mm thick hylam sheet cover fixed with suitable sizes cadmium plated iron screws and washers etc. for mounting switches, sockets, fan regulators etc complete for one light/ fan /bell /buzzer point controlled by one, one way switches complete all as specified and as directed.

All as per Item No.127 above but for One 2/3 pin socket outlet 5/6Amps on independent board

All as per Item No.127 above but for One 2/3 pin socket outlet 5/6 Amps on the same board with other switches.

All as per Item No.127 above but for one switch socket combination 15/16 Amps on independent board with cable 4 Sq mm size and earth wire 2.5 sqmm

All as per Item No.127 above but for one switch socket combination 15/16 Amps on independent board with cable 2.5 Sq mm size and earth wire 2.5 sqmm

S&F Switch piano, flush type, single pole, one way switch 5 Amps.

S & F socket outlet 2 in 1, 5 Amp flush type complete all as specified all as directed.

S&F switch socket combination 2 in 1, 5 Amps flush type.

S&F switch socket combination multipurpose 5A/ 16Amps, 5 in 1, flush type.

S&F ceiling rose surface PVC 3 terminals 25x50mm all as directed.

S&F Stepped type(five steps), electronic fan regulator, 220 volts, flush type complete all as specified and as directed.

S&F for bell push, flush type, 5 Amps 230 Volts, bearing ISI marked complete all as specified and as directed.

S&F for call bell, AC, 230 volts, single pole complete all as specified and as directed.

S&F for lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

S&F in repair LED Bulb of 09 Watt complete all as specified and directed by Engr -in Charge.

S&F LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F LED building security light fitting 35 Watt, 230 V, AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection and including all necessary items for installation complete all as specified and as directed.

S&F of 12 Watt recess mounting LED backlight round downlighter made of spun aluminium with high efficient LEDs & glare free opal diffuser, including all other accesories IP20 including testing and commissioning complete all as specified and as directed.

S&F in repairs recess mounted deep drawn PLANO size (2 ft x 2 ft) CRCA housing with higher power 36 Watt LED Seamless front frame with flat white hight transmission acrylic cover complete all as specified and as directed.

S&F for LED post top lantern, 20watts cap HERITAGE rated, ideal to light up parks, gardens and heritage site with rated voltage 240 Volts including high voltage and short circuit protection IP 65, with necessary suitable fixing accessories/arrangements complete all as specified and as directed.

S&F Bollard lamp pressure die cast powder coated housing with PC diffuser with IP-66 protection for 10 Watt LED lamp complete providing electrical connection to the bollard light fitting from the electrical system using suitable size and type of copper conductor cable and suitable size GI mast complete all as specified and directed (Note: Necessary Excavation earth work, PCC foundation including necessary bolts and nuts shall be deemed to be included in the quoted unit rate.)

S&F in repairs modular junction box made of SMC/FRP of size 350x250x150mm with provision of MCB SP, and connector terminal 4 pole indicating RYB Phase Colour and Neutral colour complete fixed to street light pole with suitable size of mild steel/ flat iron clamps, nuts and bolts complete all as specified and as directed.

S&F in repair factory made board distribution (DB) double door in sheet metal enclosure with common bus bar at incomming end, single pole & neutral, 8 way, 240 Volts suitable for housing MCBs including complete all as specified and as directed.

S&F in repair factory made board distribution (DB) double door in sheet metal enclosure with common bus bar at incomming end bus bar, triple pole & neutral (TPN), 4 way, 415 Volts suitable for fixing MCBs including complete all as specified and as directed.

S&F in repair factory made board distribution (DB) double door in sheet metal enclosure with common bus bar at incomming end bus bar, triple pole & neutral (TPN), 4 way, 415 Volts suitable for fixing MCBs including complete all as specified and as directed.

S&F for MCB 'C' curve TPN 63 Amps with breaking capacity 10 KA.

S&F for MCB 'C' curve SPN 40 Amps with breaking capacity 10 KA.

S&F for MCB 'C' curve SPN 6 to 32 Amps with breaking capacity 10 KA.

S&F for MCB 'C' curve single pole 6 to 32 Amps with breaking capacity 10 KA.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

Taking down old unserviciable submain wiring from PVC casing caping/concealed conduits upto 10 sqmm complete all as specified and direted by Engr-in-charge.

M&L for sub main wiring with two run of 6 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC casing-caping of suitable size, fixed to wall/ceiling etc including one run of 6 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed. Note : (a) PVC Casing-caping, two run wiring cables and one run of earth wire will be measured as one length (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets.

M & L earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to 4.00 GI wire by means of bolts and nuts checknuts and washers of galvanised iron or steel all as specified and shown in elecrical plate no 3 of SSR part 1 including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 80 mm dia 150 mm long reinforcement,watering funnel,40 mm dia light grade for protection of earth electrode 20 mm dia for watering all as specified and directed and tested on completion.

Supply & laying or fixing or Passing through Pipe, XLPE insulated, armoured, electric power UG cable (Heavy Duty) with aluminium Conductor, 1100 Volt Grade, Nominal Cross-Sectional Area 50 sqmm 3.5 core and testing, including brass compression cable gland, terminal lug, etc including taking down complete all as specified and as directed.

Supply & laying or fixing or Passing through Pipe, XLPE insulated, armoured, electric power UG cable (Heavy Duty) with aluminium Conductor, 1100 Volt Grade, Nominal Cross-Sectional Area 6.00 sqmm 2 core and testing, including brass compression cable gland, terminal lug, etc including taking down complete all as specified and as directed.

Boring of holes horizontal for laying not less than 50mm pipe (minimum depth 0.75 mtr from top level) under the road pavement, hard standing using trenchless technology complete all as specified and as directed. Note : cost of accessories required for making hole/bore deemed to be included in the quoted rate.

Taking down carefully serviceable ceiling fan/exhaust Fan deposit in safe custody ,after repair work fix in original position after minor repair complete all as specified and directed.

M&L Sand Cushioning (dry) in Trenches for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thick -ness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed.

M&L for common burnt clay building bricks (locally available best quality), sub-class ‘B’ designation 75 of suitable size available in market to cover LT underground cables, laid dry and flat abutting each other with gaps not exceeding 10mm including taking down old unserviceable bricks complete all as specified and directed.

S&F water heater, storage type, 230 V, AC electric, capacity of 25 litre, BEE 5 Star rated having sheet metal round body powder coated, glassline coating of inner tank with all accessories such as safety valve, thermos state, NRV, connection pipes etc.complete all as specified and directed.

M&L for sub main wiring with two run of 4 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC casing-caping of suitable size, fixed to wall/ceiling etc including one run of 4 Sqmm (nominal area) single core ( green colour), PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed. Note : (a) PVC Casing-caping, two run wiring cables and one run of earth wire will be measured as one length. (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets.

S&F for MCB SP 20 Amps 'C' series 240 Volts with breaking capacity 10 KA complete all as specified and as directed.

S&F single pole and neutral enclosure with a two pin and earth Plug and socket complete with one single pole MCB of 20 Amps rating complete all as specified and directed

Supply and install Hi wall split units indoor/ outdoor complete with cordless remote control unit and with inbuilt air ioniser and plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2 of capacity 1.5 Ton, complete all as specified and directed

S&F Voltage stabilizer for automatic operation, single phage naturally air cooled for input variation between 170V to 250V with output voltage stabilizer at 230V with accuracy of ± 2.5% and capacity 5 KVA complete all as specified and directed

S&F for MCB 'C' curve double pole 6 to 32 Amps with breaking capacity 10 KA.

R.D.CONSTRUCTION

NChetia and Sons Trading

MAZUMDAR ENTERPRISE

Construction House

M/S HAZARIKA CONSTRUCTION

FREEZCON

M/s GANDHESWAR PHUKAN