SPECIAL REPAIR TO BLDG NO P-446 AND OTHER SANCTIONED WORKS UNDER AGE B/R I AT ITARANA ALWAR

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

M&L for PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in flooring or levelling coarse 25mm thick complete all as specified & as directed.

Material and labour glazed ceramic tiles (coloured) Ist quality 300mm x 450mm x 8 to 10 mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for coloured non skid ceramic tiles 7 to 8mm thick (square/rectangular) (Ist quality) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L machine cut Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 20mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified.

M&L machine cut Kota stone slab 10 to 15mm thick , as in riser of step, skirting, dado etc. laid over & including screed bed or bedding layer of 10mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified.

M&L in repairs galvanised steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L in repairs galvanised steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L galvanised steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L galvanised steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

S&F in repairs 15 mm bore bib tap, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule.

S&F 15mm dia Stop valve of copper alloy chromium plated fancy type with long shank and cup (concealed type) screwed down, high pressure with crutch or butter fly handle screwed on both ends for iron pipe or for union fixed in repair.

S&F in repairs 15 mm bore stop valve, cast copper alloy, fancy type, chromium plated, scewed down, high pressure with capstan head, screwed both ends for iron pipe or for union complete all as specified and directed.

S&F pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot or cold' long screwed shanks and fly nuts, screwed for iron pipe and fixed bore of pipe in 15mm dia.

Supply and fixing in repair swivel shower of PTMT any colour for fixing with 15mm bore pipe, (minimum weight 40 gms) complete all as specified.

S&F in repairs PVC connection 600 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges.

S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including provision of PCC (1:5:10) type E2 in filling, making good to floor, complete all as specified.

Supply and fixing in repairs PVC valveless syphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

Taking down chowkat or frame with shutters area not exc. 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts complete all as specified

Supply & fixing factory made steel windows with side hung shutters including box type / projecting type hinges with steel handles and peg stay with glazing bars dovetailed or welded including one shop coat of Zinc Chromate primer complete all as specified.

Supply & fixing factory made steel windows with side hung shutters including box type / projecting type hinges with steel handles and peg stay without glazing bars dovetailed or welded including one shop coat of Zinc Chromate primer complete all as specified.

Supply and fixing Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples complete all as specified.

Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified.

S&F 4mm thick frosted glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified.

Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & directed.

S&F mild steel framed work as in doors / gates / steel frames etc. of angle or other section with gusset plates, rails, braces, etc., complete of Gde E-165(Fe 290), drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position complete.

Supply & fixing butt hinges of size 100mm medium weight, cold rolled mild steel ISI marked complete all as specified.

Supply and fixing 300 mm long mild steel sliding door bolts clip type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, ISI marked complete all as specified.

Supply & fixing butt hinges of size 100mm extruded aluminium alloy with galvanised mild steel hinge pin type B-21 anodised complete all as specified.

Supply and fixing 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified

Supply and fixing 200 mm long mild steel barrel tower bolts, stove enameled black with bright bolts and fixed complete all as specified

Supply and fixing 150 mm long mild steel pressed bow handle, oval type, stove enameled black complete all as specified

Supply only integral water proofing compound (ISI marked).

M&L for rendering 15mm thick in cement plaster 1:6 on stone masonry surfaces or surfaces other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

M&L rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surfaces other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified.

M&L rendering 10mm thick in cement mortar 1:6 on surface other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified.

M&L for 15mm thick rendering in two layer on fair faces of brick masonry or concrete surfaces of walls consisting of 1st layer of 10mm thick plaster in CM 1:6 and 2nd layer (setting coat or top layer) of 5 mm thick plaster in CM 1:4 mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished fair & even, complete, all as specified. Note : - Supply only water proofing compound shall be measured and paid for separately.

Material and labour preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1mm thick white wall care putty (make-Birla/JK/Asian) all as specified & as directed.

Material and labour preparation of newly plastered/asbestos cement surfaces of ceilings & applying three coats of white wash complete all as specified.

Material and labour preparation of newly plastered surface of walls & applying three coats of white wash complete all as specified.

M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1mm thick white wall care putty (make-Birla/JK/Asian) on walls all as specified & as directed.

Material and labour for preparation of newly plastered surface of walls & applying two coats of cement base paint of approved shade/tint over a coat of cement base primer complete all as specified.

M&L preparation of old decorated plastered surfaces of walls and applying one coat of cement base paint of approved shade/tint complete all as specified & as directed.

M & L for Cutting holes in stone walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3, exc half brick & not exc one brick (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall)

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified.

M&L PCC 1:3:6 type C2 using 40 mm graded stone aggregate in foundations, filling and mass concrete.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete.

Demolition of existing lime concrete/PCC padding, roof treatment of any thickness laid over RCC roof/chajja etc., removing complete layer of bitumen under concrete/PCC padding, cleaning and washing of roof with water to remove dust etc as preparation to receive treatment all as directed by Engineer-in-charge.

Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.5 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufactured by M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd or Hydrostop water proofing memdrane manufactured by M/S TIKIDAN as approved by GE, black finish reinforced with non-woven polyester matt (weighing not less than 150 gm/Sqm), with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd} at the rate of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and as directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40 Kg/Sqm. (ii) Polymeric membrane shall be taken to a height of 60cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing.(iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimuim) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimny/other vertical surfaces and polimeric membrane insterted in groove and sealed with paving bitumen. (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminium paint @ 150 ml/Sqm. (vi) Above aspects are deemed to be included in quoted rate. (vii) The net area of water proofing treatment shall be measured without any extra allowance for laps & portion inserted in groove which shall be deemed included in the quoted rates.

M&L for padding with PCC 1:2:4, type B0 (using 12.5 mm graded crushed stone aggregate ) laid to a average thickness 25mm thick over roof slab etc as in levelling course, finished even & smooth w/o using extra cement.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Grade E-165 (Fe 290) including necessary welding etc. and fixed in position.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, handle including one shop coat of Zinc Chromate primer complete all as specified.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors and similar works of Gde E-165(Fe 290) including welding etc. complete all as specified & as directed.

S&F in repairs powder coated mild steel drapery rod of 20 mm inner dia (in lengths as directed) of approved colour with & including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C all as specified & as directed.

Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F as in repairs Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and as directed.

S & F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenched or in floors of 75 mm pipe.

S&F PVC (SWR) floor trap plain with PTMT grating including jointing with solvent cement, diameter of outlet 75mm, complete.

S&F PVC (SWR) Gully trap 125/110mm, setting and jointing with solvent cement complete all as specified.

S&F 75mm bore PVC (SWR) ISI marked pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified including demolition & breaking up 75mm bore PVC pipe with fittings.

Supply and fixing 75 mm bore PVC (SWR) bends any radius complete all as specified.

S&F 110mm bore PVC (SWR) ISI marked pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified including demolition & breaking up 110mm bore PVC pipe with fittings.

Supply and fixing 110mm bore PVC (SWR) bends any radius complete all as specified.

Supply and fixing 110 mm bore PVC (SWR) vent cowl complete all as specified.

S&F in repairs vitreous china wash hand basin with pedestal, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F 20mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

Supply & fixing vitreous china urinal, half stall type, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified.

Treatement for sunken portion is as follows :- (i) Demolition of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. (ii) M&L for providing 12 mm dia holes of 40mm deep @2.00m c/c at junction of beams and columns as co-ordinal points for inserting/pouring cement slurry by pressure grouting for sunken floors of toilet , includind sealing the holes with CM 1:3, all as specified and as directed by Engineer - in - Charge. (iii) M&L for water proofing plaster for sunken portion in CM 1:3, 20 mm thick in two coats with water proofing compound at the rate of 2% by weight of cement and finishing the surface even and smooth without using extra cement. (WPC will be measured and paid seperately). (contd....) (contd....)(iv) M&L for applyin evenly two coats of industrial bitumen 85/25 at the rate of 1.20 Kg/Sqm in each coat over vertical surfaces and floors of sunken floors of toilet including cleaning of surfaces. (v) M&L for PCC 1:7:12 type D2 using 40 mm graded stone aggregate as in filling (sunken portion). etc. (vi) M&L for PCC 1:2:4 type B0 using 12.50 mm graded stone aggregate, mixed with WPC @ 2% by wt. of cement, as sub base, 75mm thick. (WPC will be measured and paid separately.) on top (vii) M&L for plastering in CM 1:4, 15 mm thick with water proofing compound at the rate of 2% by weight of cement and finishing the surface seven and fair.(WPC will be measured and paid seperately) (contd....)(contd....) Note :- Above includes (a) Test again of water tightness by pounding for 72 hours & rectify defects if any till total elimination of defect. (b) The sunken portion shall be tested for leakage / seepage / dampness by pounding with water for 72 hours. In case any defect is noticed the portion shall be grouted with cement slurry mixed with suitable chemical & tested again. The process of grouting and testing shall be repeated till leakage / seepage / dampness is eliminated. (c) Horizontal flat area to be measered.

Material and labour 100mm thick PCC (1:4:8) type D2 using 40 mm graded stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L factory made 60mm thick machine pressed precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as Specified & directed.

Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes, laying or cables, pipes etc not exc 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers n.exc 25 cm in soft/loose soil.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level n. exc 1.50 metre above the starting point complete all as specified.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil.

M&L for hardcore of broken stone or boulders, gauge exc. 63mm but not exc 100mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

M&L 40mm thick PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in damp proof course on horizontal surface using water proofing compound including necessary formwork.

M&L for reinforced cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L reinforced cement concrete (Nominal mix)1:2:4 type B1 using 20mm graded stone aggregate in columns, pillars, piers, posts, struts and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for mild steel TMT bars 10mm dia & over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and bending with and including MS wire (annealed) not less than 0.9 mm dia, complete, all as specified and directed.

All as per serial item No. 93.00 here-in-above but 8mm dia.

All as per serial item No. 93.00 here-in-above but 6 to 10mm dia in stirrups, spacers and binders.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete.

M&L for formwork to edges of concrete flats, roofs, floors etc not exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete.

M&L for formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete.

M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to NP2 pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

S&F salt glazed stone ware drain pipes of 150mm bore, grade `A’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified.

Material and labour 75 mm thick PCC (1:4:8) type D2 using 40 mm graded stone aggregate as in sub base, surface finished fair and even complete all as specified.

Supply & fixing aluminium handle 125mm size cast type, anodized complete all as specified.

S&F factory made solid PVC door frame of size 50mm x 95mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement.

Supply & fixing butt hinges of size 100mm extruded aluminium alloy with galvanised mild steel hinge pin type B-21 anodised complete all as specified.

Supply and fixing 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified

Supply and fixing sheet metal enclosure, double door type, suitable for fixing MCBs, SPN with 200 Amps rated bus bar, 4 way, 415 volts.

Taking down carefully, copper/aluminium unserviceable /perished point wiring any type for light/ fan/ socket or power complete including fittings such as switches, ceiling roses, pendant holders, lamp holders, bracket holders, regulators sockets, light fittings, lamps etc, and making good to disturbed surfaces of wall/floor/ceiling etc, complete, all as specified and directed.

Material and labour for point wiring for one light point controlled by one, one way switch with multistrand 1.50 Sqmm unsheathed copper conductor cable including continuous earth wire 1 Sqmm in green colour unsheathed copper conductor connected to common earth dolly in PVC casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS in on existing sunken MS boxes fixed on wall for mounting switch, socket, regulators etc with and including 3mm thick phenolic laminated sheet top cover, complete, all as specified.

All as per description of serial item No. 111.00 above but for one fan point controlled by one switch and regulator complete all as specified and directed.

All as per description of serial item No. 111.00 here-in-before but for one 3 pin socket outlet 5 Amps controlled by one switch, 5 Amp on same board.

All as per description of serial item No. 111.00 here-in-before but for one 3 pin socket outlet 5 Amps controlled by one switch, 5 Amp independent board.

All as per serial item No. 111.00 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

Supply and fixing switch piano flush type, single pole, one way, 5/6 Amp, 230 Volts.

Supply and fixing switch piano flush type, single pole, one way, 15/16 Amp, 230 Volts.

Supply and fixing socket outlet for 2 & 3 pin, 5 Amp, flush type 240 Volt.

Supply and fixing socket outlet for 2 in 1, 3 pin 5 & 15 Amp, flush type 240 Volt.

Supply and fixing ceiling rose surface Bakelite 65x50mm two or three terminals.

Supply and fixing decorative ultra slim liner LED lighting fixture with extended polycarbonate, environmental friendly, energy efficient suitable for 16 Watt to 20 Watt with LED tube of model E-LITE LED Pride and connecting up with and including white coloured flat/round twin core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete, all as specified & directed. Make :- Havells Cat Part No LHEXBLP7PN1W018 or equivalent Make given in PS as approved by GE

Supply and fixing lamp holder, angular PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply and fixing in holder Adore LED lamp 9/10 watt complete all as specified and directed. Make :- Havells Cat Part No LHLDERHEML8X010 or equivalent Make given in PS as approved by GE

Supply and fixing new fan regulators electronic step up type socket size and connecting up, ISI marked flush type, 240 Volts complete all as specified and directed.

Supply and fixing in repairs sheet metal enclosures, double door type, suitable for fixing MCB,s, SPN with 200 Amps rated bus bar, 8 way, 240 volts.

Supply and fixing sheet metal enclosure, double door type, suitable for fixing MCBs, TPN with 200 Amps rated bus bar, 4 way, 415 volts.

Supply and fixing MCB 32 Amps, single pole & neutral, 240 Volts.

Supply and fixing MCB 6 to 32 Amps, single pole, 240 Volts.

Supply and fixing in repairs MCB 63 Amps, single pole & neutral, 240 Volts.

Supply and fixing sub main wiring on and including PVC casing caping, 1100 Volts grade cable, PVC insulated copper conductor and over all PVC unsheathed for sub main wiring multistranded conductor of 6 Sqmm single core cable and earth wire of 6 Sqmm unsheathed copper conductor complete. (Two run of cable with one run of earth wire should measured as one length) including taking down existing unserviceable sub main wiring.

Supply and fixing 2nd class hard wood rectangular block open recessed of size 60x45x5 cm depth with 3mm thick hylum/Bakelite sheet on top grouted with 4 Nos bolts.

Supply and fixing 2nd class hard wood rectangular block open recessed of size 30x25x5 cm depth with 3mm thick hylum/Bakelite sheet on top grouted with 4 Nos bolts.

Supply and fixing LED type street DRACO Series light luminaire 20 watt 230 V 50 Hz including all necessary fitting accessories and LED complete, all as specified & directed. Make :- C&S Cat Part No LTESS20WLED or equivalent Make given in PS as approved by GE

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 16 sqmm 2 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified. Note :- Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 10sqmm 2 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified. Note :- Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

M&L galvanised steel water tubing light grade of 40mm bore with & including all fittings complete laid in trenches. Note :- Excavation & earthwork shall be measured & paid for separately.

M&L galvanised steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

S&F Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore.

Supply & fixing and testing exhaust fan of 300mm sweep heavy duty, double ball bearing, 1400 RPM, suitable for SP 230 / 250 volt, 50 Hz AC supply complete with louver shutter including fixing / grouting of frame in wall & cutting opening complete with covers & connecting with & including 3 Nos 1.5 sqmm single core, PVC insulated but unsheathed FRLS 1100 volts grade cable with multi-stranded copper conductor from ceiling rose to fan complete.

Material and labour earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part I and connection to main switch board or panel and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, PCC chamber (1:3:6) type C-2, charcoal and salt mixed layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, 75 mm thick RCC cover 1:2:4 type B-1 shall be provided on CI frame etc complete all as specified & as directed. Note : PCC chamber shall be constructed at least 1.5 m away from the earth electrode. The pipe for watering shall be provided in slanting manner

Cutting & inserting TEE, L bow , Bend/ Collar and tapping the connection from the existing 20mm GI tubing line for taking branch connections including tapping accessories complete all as directed.

M & L for dry sand cushioning to PVC under ground cable with screened and washed sand and punning to provide a required cover complete all as specified and directed. Note :- Thickness after punning shall be considered for payment.

M & L for brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection including taking down old unserviceable bricks complete all as specified & directed.

M/s Laxmi Enterprises

M/s S Amarjit Singh

M/S JINDAL ENTERPRISES

M/s ASK Enterprises

M/s KUNTAL ASSOCIATES

GAR CONSTRUCTIONS