REPAIRS TO COMPOUND WALL DRAIN FENCING FOOTPATHS HARD STANDING ETC AT MH AND RH AREA UNDER GE MH AND RH KIRKEE

Amount

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar

Demolition of cement concrete un reinforced in ground floors and pavings n.exc 15 cm thick below or above ground level.

Demolition of cement concrete (reinforcement) of any description and in any position any any thickness all as specified

Dismantling wrought iron or mild steel work of any description all as specified

Dismantling fencing wire mesh any type

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

Dismantling of plain or corrugated asbestos cement sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

Demolition of precast cement concrete block/ stone masonry built in cement mortar including all quoins, arches, pillars etc

M&L for Cement concrete 75mm thick type C- 1, 1:3:6 (20mm graded aggregate) as in sub floor and paving etc all as specified

M&L Cement concrete type D2 1:4:8 as in foundation filling and mass concrete all as specified and directed.

Excavation in trenches n exc 1.50m wide and 1.50m depth for foundation, man hole etc and getting out in hard/dense soil.

Returing filling in including spreading leveling watering well ramming in layers n;exc 25cm thick with soil obtained from excavation all as specified.

Removing excavated material exc. 250 m but n.exc. 500m and depositing where directed

M&L for RCC Type B1 1:2:4 (nomonal mix) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified

M&L for RCC Type B1 1:2:4 (nomonal mix) in columns, pillars, piers, posts and struts all as specified

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter all as specified

Formwork to sides of pillars, posts, struts, piers, columns and stanchions all as specified

S&F of TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Fe-410-W (Gde.E-250)

All as per item No. 18 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L Coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick plastering in cm 1:4 all as specified.

M&L for 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete fixed over and including backing coat of 10mm thickin CM 1:4 all as specified

M & L for 80mm thick M-40 coloured glossy finished interlocking tiles/ blocks any shape and size , jointed & pointed in neat cement slurry with pigment to match the shade of tile etc complete all as specified and as directed.

M&L Cement concrete Type C2 1:3:6 (40mm graded aggregate)in surface channels and drains all as specified

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc

M & L Pre-cast cement concrete type C1 1:3:6 block masonry with solid blocks, exc. 10 cm in width and setting in mortar 1:4, complete all as specified

Providing cement concrete 1:2:4 type B0 as in copings, filleting etc.

M & L for rendering 15 mm thick on fair faces of block masonry surfaces in cement plaster 1:4 all as specified and directed

Supply only Chain link MS galvanisd fencing, (with PVC coating) having 2.5 mm dia GI wire with 1.5 mm thick PVC coating (Total 4.00 mm dia) of dark green shade as directed by Engg-In-Charge) all as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire

S & F MS angle iron in fencing posts & struts including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets ( for securing wire mesh etc) including all necessary, drilling, bolting or riveting etc and similar work conforming to Fe-410-0 or Fe-310-0.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., Ladders complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe-410-W(Gde E-250) quality-B

M & L for PCC 1:2:4 type B2 ( 40 mm graded agggrgates) as in foundation of rails post etc.all as specified

S & F 10 mm dia MS round bars for tightening of chain link fencing woven through chain link & fitted completely.

M&L for walling of random rubble, uncoursed, well bounded,bedded and solidly hearted, built in CM 1:6 all as specified and directed

Extra over stone walling for hammer dressing to face stones and dressing of face beds and jointse held against the dressed surface n exc.40mm, as specified, of random rubble walling, uncoursed or brought upto courses

All as per Item No 34 but except stone

M&L for Keyed pointing to random or polygonal rubble, uncoursed or brought upto course in CM 1:4 all as specified and directed

M&L Chequred Cement concrete coloured tiles 30 cm x 30 cm x 20 mm thick, glossy finished set jointed and pointed in neat cement slurry in floors, and cut and polished with grey cement and pigments laid over 15mm thick screed in CM 1:6 complete all as specified and as directed.

S&F vitrified body tiles 10mm thick (square/ rectangular) area of each tiles 300X300mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tiles laid over and including 15mm thick screed bed or bedding in layers in cement mortar 1:6 all as directed

M&L for sand/ stone dust filling under floors or in foundations including watering and consolidation all as specified

Welding in repairs exc 2.5 cm but n.exc 5.0 cm in length of thickness of metal n.exc 6mm

Running welding in repairs of metal thickness to be welded n.exc 6mm

S&F in repairs Galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of stan dard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) as in wire entanglements aprons, barriers, gates etc. ncluding restraining resecuring and making good to staples

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F of Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates of Gde Fe-410-W(Gde-E250) quality-A

M&L for Providing precast cement concrete type C0 1:2:4 (12.5mm graded aggregate) louvres and jallies, 25mm thick (mea sured solid), including all mould- ings but excluding frame set in cement mortar 1:4 all as specified.

M & L for preparing new steel surfaces over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified.

M&L for two coats of cement base paint on newly plastered surfaces of walls including preperation of new surfaces all as specified

S & f Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding/eaves gutter/valley gutter etc, fixed with self tapping screws as specified

s.k.engineers

ANJALI CONSTRUCTIONS

GGS Infra

Aishwarya Constructions

M/S JAYCONSTRUCTION CO

SAMBHAJI D JARANDE

MAHESH DADAJI BACHHAV

V.R.PRAJAPATI AND CO.

Shri Sant Cosntruction

MANISH VEDPRAKASH ARORA

S.R.M.K Enterprises