REPAIR TO JOINERY AT CERTAIN OTM, OMQ AND SMQ ACCN AND OTHER MISC B/R WORK AT BRD, AF STN TUGHLAKABAD UNDER GE (AF) TUGHLAKABAD

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 sqm but not exceeding 4 sqm each, making surface good and smooth to receive new frame any type and removing old chowkat/fame with shutter from site complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each making surface good and smooth to receive new frame any type and removing old chowkat/fame with shutter from site complete all as specified and directed by Engr-in-Charge.

Taking down shutters of any description exc. 1 sqm and n. exc. 2 sqm each and removing from site complete all as specified and directed by Engr-in-Charge.

Taking down shutters of any description n exc. 1 sqm each and removing from site complete all as specified and directed by Engr-in-Charge.

Easing of steel window shutter for properly closing/opening tightening of hinges by oiling, greasing or by replacing of new box type hinges including necessary cutting & welding complete all as specified and directed by Engr-in-Charge. Note:- one unit shall be comprising of one window irrespective of no of leaves/shutter. work to be carried out up to 12m height.

Easing of wooden door shutters/Almn door/PVC door shutter/Almn window (One unit shall comprising of one window/CB/Showcase/ irrespective of number of leaves) for properly closing/opening tightening of hinges or changing the position of hinges adjustment of tower bolts sliding bolt etc at any height complete all as specified and directed by Engr-in-Charge.

Framed work 410-W (Gde E-250 )as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing including hinges welding complete all as specified and directed by Engr-in-Charge.

S&F in repair mild steel gate ornamental type as per direction of Engr-in-Charge. Note: Design/Pattern shall be approved by Accepting Officer and no extra claim by contractor for same.

M&L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wind ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe410-0 or Fe 310-0 complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B1 using 12.5 mm graded stone aggregate as in bed blocks etc for embedding hold fasts complete all as specified and directed by Engr-in-Charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed by Engr-in-Charge.

S&F Factory Made Solid PVC Moulded Door Shutter with particle board, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing specified in SSR and as directed by Engineer-in-Charge

S&F Aluminium anodised 100 mm long Butt hinges with galvanised mild steel screws complete all as specified and directed by Engr-in-Charge.

S&F Aliminium anodised barrel tower bolts, 150 mm long complete all as specified and directed by Engr-in-Charge.

S&F Aluminium anodised handles, cast type anodised 125 mm long complete all as specified and directed by Engr-in-Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 100 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 125 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S&F 35 mm thick factory made second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, wire gauze, etc. divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a), supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge.

M&L for Flush shutters,30mm thick solid core construction, with block board core and plywood face panels, commercial type on one sides with 0.9mm thick decorative laminate type 1 on both side and lipping/frame to match surface finish, colour and pattern as approved, fixed with approved adhesive as per maker's instructions complete all as specified and directed by Engr-in-Charge.

M&L for Flush shutters, 25mm thick solid core construction, with block board core and plywood face panels, commercial type on one sides and decorative on both side with decorative face veneer with lipping/frame to match surface finish, colour and pattern as approved, fixed with approved adhesive as per maker's instructions complete all as specified and directed by Engr-in-Charge.

S&F 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work rebate suitable for cupboard shutters complete all as specified and directed by Engr-in-Charge.

M&L for 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to aluminium frame work with necessary clip, beading, nut bolts and screws fixed in floor and walls complete all as specified and directed by Engr-in-Charge.

S&F, 100 mm long butt hinges, extruded alminium alloy with galavanised mild steel hinge pin, anodised and fixed , type C-21 complete all as specified and directed by Engr-in-Charge.

S&F 300 mm long mild steel sliding bolt plate type stove enamelled black with bright bolt not less than 12 mm dia with and including a minium of 6 bolts and nuts four on bolt plate and two on staple plate and fixed complete all as specified and directed by Engr-in-Charge.

S&F 200 mm long mild steel barrel tower bolts, ISI market stove enamelled block with bright bolt and fixed complete all as specified and directed by Engr-in-Charge.

S&F 150mm long oval type mild steel pressed handles, ISI marked stove enamelled black complete all as specified and directed by Engr-in-Charge.

S&F 100 mm long aluminium anodised hasp and staple safety tape including bolts to hinge plate and fixed with screws complete all as specified and directed by Engr-in-Charge.

S&F galvanised mild steel wire cloth of 0.56 mm nominal dia of wire and 1.18mm average width of aperture and fixed with beading tinned tacks or galvanized wire staples in steel/wooden window/door fixed with nails/welding complete all as specified and directed by Engr-in-Charge.

S&F in repair galvanised mild steel wire cloth of 0.56 mm nominal dia of wire and 1.18mm average width of aperture and fixed with beading tinned tacks or galvanized wire staples in steel/wooden window/door fixed with nails/welding complete all as specified and directed by Engr-in-Charge.

M&L for taking out old broken glass of any description from old wooden or metal frame or stones, concrete or brick surrounds glazed with putty or fixed with beads including punching or drilling out old glazing pins/spring clips and providing and fixing new sheet glass ordinary quality 3.00 mm thick and glazing with oil putty in square n exc 0.50 sqm in each panes fixed to steel or wooden window frames complete all as specified and directed by Engr-in-Charge. Note: All dismantling/demolished material removed from MOD land completely. Rate of removal outside side from MoD land deemed to be included in the same item.

S&F factory made white color casement UPVC windows (openable) are made of UPVC extruded profile with wall thickness of (2.3mm to 2.5mm) window profile with hollow section with multi chamber, Frame (50mmx30mm), sash (74mmx34mm), mullion profile (one vertical length in between frame and shutter 72mm x32mm), including glazed through 5mm thick glass with glazing bead (28mmx26mm) will be metered cut and fusion welded at all corners, including drilling of holes for fixing hardware with handle (150mmx17mm), suitable hinges(75mm) and drainage of water etc making arrangement of fixing of hardware, EPDM gasket(1.mm to 3mm) thick, GI of (1.2mm tto 1.5mm) thick to be inserted in required profile , fame will be fixed by wall with 8mmx100mm long fasteners complete fittings and fixture as per manufacture's specification and direction of Engr-in-Charge. Note : Quoted rate included all above complete description.

S&F factory made white color casement UPVC windows (openable) are made of UPVC extruded profile with wall thickness of (2.3mm to 2.5mm), window profile with hollow section with multi chamber, Frame (50mmx30mm), sash (74mmx34mm), mullion profile (one vertical length in between frame and shutter 72mm x32mm), including glazed through stainless steel wire mesh cloth 0.36 mm nominal dia of wire and average width of aperture 1.18 mm with suitable beading (28mmx26mm) will be metered cut and fusion welded at all corners, including drilling of holes for fixing hardware with handle (150mmx17mm), suitable hinges(75mm) and drainage of water etc making arrangement of fixing of hardware, EPDM gasket(1.mm to 3mm) thick, GI of (1.2mm tto 1.5mm) thick to be inserted in required profile , fame will be fixed by wall with 8mmx100mm long fasteners complete fittings and fixtures as per manufacture's specification and direction of Engr-in-Charge. Note : Quoted rate included all above complete description.

S&F factory made white color 3-Track UPVC sliding window are made of UPVC extruded profile with wall thickness of (2.3mm to 2.5mm), window profile with hollow section with multi chamber, Frame (91mmx47mm), sliding gazed sash (60mmx34mm), 1 No SS mesh sash (60mmx34mm), sliding interlock (one vertical length in each shutter) (38.4mm x29.5mm), incl glazed through 5mm thick glass with glazing bead (18mmx16mm) will be metered cut and fusion welded at all corners, including drilling of holes for fixing hardware with 2 Nos touch lock, 06 Nos roller wheel and drainage of water etc making arrangement of fixing of hardware, EPDM gasket(1.2 mm to 3mm) thick, GI of (1.2mm to 1.5mm) thick in frame, 2 sliding sash and 1 sliding mesh sash to be inserted in required profile , fame will be fixed by wall with 8mmx100mm long fasteners complete fittings and fixtures as per manufacture's specification and direction of Engr-in-Charge. Note : Quoted rate included all above complete description.

S&F factory made Ventilators 1.25 mm thick box type (primer coated) ERW hollow P sections of size 60mm X 25mm including grill using 10 Sqmm bar double riveted both gauge and glass shutter comprised gauged glazed skeleton shutters ERW section 50mm X 20mm and 1mm thick with two openable leafs consisting 2 nos sash bar of T section 20mm X 3mm complete welded to frame with one vertical mullion of ERW box type T section of size 60mm X 25mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B1 four numbers of each window including following fittings welded to frame shutter :- (a) Hold fast, 150 mm long of 12mmX3mm made to shape 04 nos per ventilator (b) handle of Z section 20mmX25mm, 100 mm long -per leaf (c) MS tower bolt 150mm long - 02 Nos per leaf (d) Z section 20mmX25mm, 100 mm long stopper -01 nos per leaf (e) Cleat 55mm long of hollow square 15mm X20mmX63mm welded to hinge -01 Nos per Leaf (f) MS pintal hinges of size 75mmX12mm- 02 Nos per leaf including stainless steel wire cloth, 0.25mm to 0.36mm nominal dia of wire and average width of aperture 1.40mm to 2mm and fixed with aluminium wire staples and glass pan 3mm thick fixed with MS pin and oil putty including two coats of synthetic enamel paint cocomplete all as specified and directed by Engr-in-Charge. Note: During fixing of ventilator surface shall be make good in plumb with existing finishes like cement plaster, similar wall tile, floor tile etc and as per site requirement .

S&F factory made Steel windows 1.25 mm thick box type (primer coated) ERW hollow P sections of size 60mm X 25mm including grill using 10 Sqmm bar double riveted both gaze and glass shutter comprised gauged glazed skeleton shutters ERW section 50mm X 20mm and 1mm thick with two openable leafs consisting 2 nos sash bar of T section 20mm X 3mm complete welded to frame with one vertical mullion of ERW box type T section of size 60mm X 25mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B1 four numbers of each window including following fittings welded to frame shutter :- (a) Hold fast, 150 mm long of 12mmX3mm made to shape 04 nos per window (b) handle of Z section 20mmX25mm, 100 mm long -per leaf (c) Mild steel tower bolt 150mm long - 02 Nos per leaf (d) Z section 20mmX25mm, 100 mm long stopper -01 nos per leaf (e) Cleat 55mm long of hollow square 15mm X20mmX63mm welded to hinge -01 Nos per Leaf (f) MS pintal hinges of size 75mmX12mm- 02 Nos per leaf including stainless steel wire cloth, 0.25mm to 0.36mm nominal dia of wire and average width of aperture 1.40mm to 2mm and fixed with aluminium wire staples and glass pan 3mm thick fixed with MS pin and oil putty including two coats of synthetic enamel paint complecomplete all as specified and directed by Engr-in-Charge. Note: During fixing of window surface shall be make good in plumb with existing finishes like cement plaster, similar wall tile, floor tile etc and as per site requirement .

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed by Engr-in-Charge.

Supply and fixed in repairs of 150 mm aluminium handles cast type anodized complete all as specified and directed by Engr-in-Charge.

Supply and fixed in repair of 300 mm aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair medium weight colled rolled butt hinges, medium weight of size 100 mm complete all as specified and directed by Engr-in-Charge.

S&F 125mm stainless steel hasp and staple of safety type with mild steel hinge pin including bolt of hinge plate and fixed with screws complete all as specified and directed by Engr-in-Charge.

S&F in repair 150 mm long stainless steel barrel tower bolts of extruded section and fixed (ISI Marked) complete all as specified and directed by Engr-in-Charge.

S&F in repair 100 mm long stainless steel barrel tower bolts of extruded section and fixed (ISI Marked) complete all as specified and directed by Engr-in-Charge.

S&F in repairs stainless steel handles, fabricated type of size 150 mm (ISI Marked) complete all as specified and directed by Engr-in-Charge.

S&F in repairs stainless steel handles, fabricated type of size 100 mm (ISI Marked) complete all as specified and directed by Engr-in-Charge.

S&F in repairs Continuous (piano) hinges 30mm width in flap, stainless steel, bright finish or electrogalvanised complete all as specified and directed by Engr-in-Charge.

S&F in repair of 150 mm floor door stopper of aluminium alloy body and tongue andodised with hard drawn steel spring fixed in floor complete all as specified and directed by Engr-in-Charge.

S&F in repairs 40 mm dia cupboard knobs fixed with nut svrew and washer of mild steel bright bolt complete all as specified and directed by Engr-in-Charge.

Repairs to Aluminium doors exc 1.50 Sqm but n exc 5.00 Sqm by necessary joining cleat, glazing clips, rubber neoprene packing handles 2 Nos in each doors, hinges anodised aluminium snap beading screw etc including chowkhat and refix in the same opening after complete repair except glass complete all as specified and directed by Engr-in-Charge.

Repairs to Aluminium doors n exc 1.50 Sqm by necessary joining cleat, glazing clips, rubber neoprene packing handles 2 Nos in each doors, hinges anodised aluminium snap beading scrw etc and refix in the same opening after complete repair except glass complete all as specified and directed by Engr-in-Charge.

S&F in repairs, Aluminium door closer hydraulically regulated, designation No 1, universal type suitable for door shutters upto 1000 mm in width and of wt not more than 80 kg complete all as specified and directed by Engr-in-Charge.

S&F in repair brass Locks for cupboard/Glass doors, grade I, size 50mm complete all as specified and directed by Engr-in-Charge.

S&F in repair Magnetic catcher for Wardrobe, Cub-boards etc. complete all as specified and directed by Engr-in-Charge.

S&F in repair sliding channels for holding glasses in wardrobes complete all as specified and directed by Engr-in-Charge.

S&F in repair stainless steel Pivot hinge of size not exc. 75 mm for glass doors complete all as specified and directed by Engr-in-Charge.

S&F in repairs double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engr-in-Charge.

S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing fixed with and including 5.50mm thick tinted glass fixed with rubber gasket with aluminium heading, clips frame made with aluminium box sec as appended below complete all as specified and directed by Engr-in-Charge. (a) Frame 100x44x1.48mm thick with rawl plug (b) Middle and lock rail : 150x44x1.48mm thick (c) Bottom rail : 150x44x1.48mm thick (d) Top rail/style : 85x44x1.48mm thick (e) Aluminium beading : 0.7mm thick (f) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long brass mortise lock 100mm 4 leaver aluminium stopper, cleat, double action floor spring hydraulically regulated made of n. less than 1.25mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other part of steel heavy duty (ISI marked or its equivalent approved make) (g) Making good of wall surface to match with existing surface.

S&F Aluminium Anodized powder coated aluminium frame for doors, windows, ventilators, portion wall with one or more rebates including joining cleat for fixing etc (thikness of powder coating is 50 micron) complete all as specified and directed by Engr-in-Charge.

S&F anodised aluminium powder coating of any colour (Thickness of powder coating not less than 50 micron) window and ventilator shutter side hung type suitable for glass pan without sash bar, aluminium sections weighing 0.55kg/m incl necessary joining cleat glazing clips, rubber neoprene packing, alumimium anodised snap beading, screws , peg stay 150mm long -1 No, hinges type B-21 100mm long -2 Nos, suitable handle -1 No complete all as specified handles 1 Nos in each window, hinges, aluminium snap beading screws complete all as specified and directed by Engr-in-Charge.

S&F anodised aluminium powder coating of any colour (Thickness of powder coating not less than 50 micron) window and ventilator shutter side hung type suitable for wire mes without sash bar, aluminium sections weighing 0.55kg/m incl necessary joining cleat glazing clips, rubber neoprene packing, alumimium anodised snap beading, screws , peg stay 150mm long -1 No, hinges type B-21 100mm long -2 Nos, suitable handle -1 No complete all as specified handles 1 Nos in each window, hinges, aluminium snap beading screws complete all as specified and directed by Engr-in-Charge.

S&F 4.0 mm thick Figured glass, pin head type and glazing with aluminium beadding screws or oil putty in square not exceeding 0.5 sqm in each pane and fix in aluminium door / window/ventilator complete all as specified and directed by Engr-in-Charge.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples and fixed with tinned tacks ro galvanised wire stapple complete all as specified and directed by Engr-in-Charge.

Supply and fixing 7mm thick aluminium grill of make ' Deco grill DG-104 model fitted in to suitable aluminium channel and fixed to windows / ventilators including channel complete all as specified and directed by Engr-in-Charge.

S&F in repairs stainless steel curtain rod of dia 20-25 mm complete all as specified and directed by Engr-in-Charge.

S&F Stainless steel bracket for holding curtain rodes of dia 20-25 mm complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide or zinc chrome primer complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new wooden surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of aluminium wood primer complete all as specified and directed by Engr-in-Charge.

M&L for 6 mm thick acrylic sheet n exc 0.50 sqm in each pane & fixed to steel window by drilling holes/punching/screwing fixed with beads with metal panel pins/spring clips in metal surrounds including taking down old glass with putty complete all as specified and directed by Engr-in-Charge. Note: Work to be carried out up to 16m height.

S&F in repair colour venetian blinds of 100mm width of strip with frame and fittings fixtures complete all as specified and directed by Engr-in-Charge.

Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed by Engr-in-charge.

S&F Anodised aluminium snap grid frame work (600mm x 600mm) for false ceiling complete all as specified and directed by Engr-in-charge.

S&F 12 mm thick Perforated particle board/tiles for insulation and acoustic purposes, 60x60 cm in size, fixed with nails to timber frame work or with staples on snap arid complete all as specified and directed by Engr-in-charge.

S&F 15mm-20mm thick WPC louvers wall/ceiling panel on PVC frame with SS wall panel fastener clip and screws as per site requirement including fillets/cornice as directed by Engr-in-Charge. Note: Color and Pattern shall be approved by Accepting Officer. No extra claim by the contractor for the same.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws to steel frame work incl dismantling of plain or corrugated steel galvalume sheet/valley gutter any gauge, thickness including nainital or similar pattern roof coverings including ridges for north light truss, complete all as specified and directed by Engr-in-Charge.

S&F in repair of corner glass shelf 12" complete all as specified and directed by Engr-in-Charge.

S&F in repair of 5mm thick front glass shelf 450 mm long complete all as specified and directed by Engr-in-Charge.

Taking down steel rolling shutter of size exc 5 sqm but not exc 15 sqm each complete all as specified and directed by Engr-in-Charge.

S&F gear operated type rolling shutters of 1.25 mm thick laths, without ball bearing including top cover, anchoring rod, and one shop coat of primer with bevel gear box and crank handle erected in position as indicated in position complete all as specified and directed by Engr-in-Charge.

S&F in repair suitable ball bearing for rolling shutters complete all as specified and directed by Engr-in-Charge.

S&F in repair safety lever locks mild steel with 4 levers per rolling shutters complete all as specified and directed by Engr-in-Charge.

Taking down hood of rolling shutter of size exc 5 sqm but n exc 15 sqm each by making all arrangement like ladder, staging rope, chain & pulley etc carrying out repair works, including replacement of nut bolts & Nails etc replacing defective parts, oiling greasing the mechanical parts including side rails and refixing the same in position and repairing the damaged cemented masonry/concrete to match with the old structure complete all as specified and directed by Engr-in-Charge.

Green Leaves (BID ID -3334190)

M/S S.K.Electricals (BID ID -3324598)

M/S DEVRAJ SINGHAL (BID ID -3326008)

Neeraj Enterprises (BID ID -3328293)

ANAND ENTERPRISES (BID ID -3332832)

Deepak Electricals (BID ID -3328984)

akenterprises (BID ID -3332799)

Bee Kay Engineers & Contractors (BID ID -3332856)

The new hut furnitures (BID ID -3333232)

V r traders (BID ID -3333057)