PROVN OF OTM ACCN FOR WOMEN ENTRY MPs IN PRO UNIT FOR TEN WOMEN MPs INCLUDING E/M WORKS AT SRI GANGANAGAR MIL STN

Site clearance in soft/loose soil complete all as specified and directed by Engr-in-Charge.

Removal of excavated material soil not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.5 mtr wide and not ecxceedinf 1.5 mtr depth for laying of cables complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm complete all as specified and directed by Engr-in-Charge .

Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m in any kind of soil complete all as specified and directed by Engr-in-Charge.

M&L for 'Anti termite treatment (Pre treatment) Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed by Engr-in-Charge.

M&L for 'Anti termite treatment (Pre treatment) Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed by Engr-in-Charge.

M & L for PCC 1:4:8 type, D2 (40mm graded stone agg.) in foundation, mass concrete and filiings complete all as specified and directed by Engr-in-Charge

M&L for providing reinforcement cement concrete, M-25 (using 20mm graded stone agg)as in footing, foundation,beams, plinth beams, base for columns and mass concrete etc. complete all as specified and directed by Engr-in-Charge

M&L for providing reinforcement cement concrete, M-25 (using 20mm graded stone agg) as in columns complete all as specified and directed by Engr-in-Charge

M&L for providing reinforcement cement concrete, M-25 (using 20mm graded stone agg) as in beams, cantilevers, bressumers, lintel over 1.5m span complete all as specified and directed by Engr-in-Charge

M&L for providing reinforcement cement concrete in M-25 (using 20mm graded stone agg) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-Charge

M&L for providing reinforcement cement concrete, M-25 (using 20mm graded stone agg) as in Chajja complete all as specified and directed by Engr-in-Charge

Use & waste of Formwork sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to better complete all as specified and directed by Engr-in-Charge

Use & waste of Formwork sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed by Engr-in-Charge

Use & waste of Formwork sides and soffits of floor or roof beams, beam haunchings, girders, ressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed by Engr-in-Charge

Use & waste of Formwork soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed by Engr-in-Charge

Use & waste of Formwor kchullah hoods, chajjas, troughs and similar items in cluding edges complete all as specified and directed by Engr-in-Charge

Use & waste of Formwork rough finished surfaces of concrete to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls and similar works exc 10cm but n. exc 20cm wide complete all as specified and directed by Engr-in-Charge

M&L 15 mm cement plaster in CM 1:3 while the concrete is green with approved water proofing compound in proportion as recommended by the manufacturer (Waterproofing compound measured and paid saperately) complete all as specified and directed by Engr-in-Charge

Supply only integral liquid water proofing compound complete all as specified & as directed by Engineer-in-Charge.

S&F mild steel TMT reinforcement bars of Grade Fe 500D/Fe 550D (as approved by GE) 10mm dia and over , cut to length, bent to shape requred, including crancing bending and binding with mild steel (anneal) wire not less than 0.90mm dia complete all as specified and directed by Engr-in-Charge

S&F mild steel TMT reinforcement bars of Grade Fe 500D/Fe 550D (as approved by GE) 6 to 8 mm dia, cut to length, bent to shape requred, including crancing bending and binding with mild steel (anneal) wire not less than 0.90mm dia complete all as specified and directed by Engr-in-Charge

S&F mild steel TMT reinforcement bars of Grade Fe 500D/Fe 550D (as approved by GE) 6 to 10mm dia a as in stirrups, spacers and binders complete all as specified and directed by Engr-in-Charge

M&L brickwork with sub class `B' Bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

M & L Brick work with Fly ash bricks, straight or curved on plan exe 6 mtr mean radius built in CM 1:6 complete all as specified and directed by Engr-in-Charge

M&L for Brickwork with Fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed by Engr-in-Charge

M & L for Hardcore of brocken brick gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engr-in-Charge

M & L for 100 mm thick PCC 1:4:8 type, D2 (40mm graded stone agg) as in sub base complete all as specified and directed by Engr-in-Charge

M&L for providing cement concrete 1:2:4 type B0(using 12.5 mm graded crushed stone aggregate), 25mm thick as in sub base in floor/paving etc complete all as specified and directed by Engr-in-Charge

M&L 15mm thick, rendering in cement mortar CM 1:4 to brick/concrete wall surfaces finished even & smooth without using extra cement complete all as specified and directed by Engr-in-Charge

M&L 15mm thick, rendering in cement mortar 1:6 to brick/concrete wall surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 5 mm thick cement plaster in cement mortar 1:3 on ceiling surfaces finshed even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge

Prepration of New external plastered wall surface and applying complete all as specified complete all as specified and directed by Engineer-in-charge of the following :- (a) Applying 1mm thick wall care putty on wall surface and smoothening the surface prepatory to paint. (b) Applying 02 coats of exterior emulsion paint (light shade) with highlighter of any approved shade, @ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion and primer complete all as specified and directed.

Prepration of New internal plastered wall/Ceiling surface and applying complete all as specified complete all as specified and directed by Engineer-in-charge of the following :- (a) Applying 1.5 mm thick wall care putty on wall surface and smoothening the surface prepatory to paint. (b) Applying 02 coats of interior emulsion paint (light shade) @ 10 sq.m/litre/2 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion and primer complete all as specified and directed.

M&L for 600x300x7-8mm thick Premium (1st qulaity) straight edges, glazed ceramic coloured tiles as in vertical sufaces such as skirting or dado set & jointed in neat cement slurry & pointed in matching coloured polymer based grout to match the shade of tiles including 10mm backing coat in CM 1:4 complete all as specified and directed by Engr-in-Charge

M&L non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) Premium (1st qulaity) straight edges, glazed ceramic coloured tiles area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in matching coloured polymer based grout to match over and incl 20 mm thick screed bed in cm 1:4 complete all as specified and directed by Engr-in-Charge

M & L for 75 mm thick PCC 1:3:6 type, C2 (40mm graded stone agg) as in plinth protection. Note : Rates inclued for forming expansion joints of span n exc 3 m and joints should be filled with bitumen mastic grade B complete all as specified and directed by Engr-in-Charge

S&F for Factory made single extruded laminated WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant WPC to be laminated with PVC foil of minimum 14 mircons thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws all as per direction of Engineer in- Charge. (a) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (b) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x250mm - 1 nos per leaf (d) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf Note : 1: Test certificate of manufacturer to be provided by contractor . 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.

S&F for Factory made single extruded laminated WPC (Wood Polymer Composite) solid decorative type glazed/guage skeleton door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus ofelasticity 850 N/mm2 and resistance to spread of flameof Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws,including for fixing Mosquito wire mesh SS-304 grade (measured and paid as separate item) and XPM (25mmx25mm diagonal) aluminum powder coated mesh combiely in panel area of door except stiles and rails to be panelled wire mesh with self tapping round headed screws at required distance screws and edge covered with feathered PVC edge beading all around mesh and fixing stainless steel butt hinges of required size wirth necessary full body theaded star headed countersunk SS screws all per direction of Engineer-n-Charge. Note: (a) stainless steel(304 grade) finished butt hinges 100mm -04 Nos per leaf (b) Stainless steel (304 grade ) finished square tower bolt 200mm long -02 Nos per leaf (c)stainless steel (304 grade) finished handles 200mm -02 Nos per leaf (d)stainless steel (304 grade) finishedsliding door bolt 300mm -01 Nos per leaf (e)stainless steel (304 grade) finished floor door stopper -01 Nos per leaf(f) stainless steel (304 grade) wire cloth fixing as per manufacture. Note : 1: Test certificate of manufacturer to be provided by contractor . 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.

S&F stainless steel SS-304 Grade wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engr-in-Charge

S&F for Factory made single extruded laminated WPC (Wood Polymer Composite) 100 % solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of but of Frame size 75 x 50 mm(moulded) single rebated, made from wood polymer composite (single extruded process) material comprising of virgin PVC polymer of K value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 780 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be not paid for separately) Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F for Factory made single extruded laminated WPC (Wood Polymer Composite) 100% solid plain flush door shutter of 24 mm thick size comprising of virgin polymer of K value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: 125 mm long stainless steel butt hinges (03 nos), 150 mm long aluminium handles (02 Nos) and 150 mm long aluminium tower bolts shall not be paid separately

S & F for framed work such as grills, gratings, etc.. & framework of water tanks and similar work conforming to Fe. 290.Gde-E-165 complete all as specified and directed by Engr-in-Charge

M&L for preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed by Engineer-in-Charge.

Supply and fix sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,flat edge (matt finish) bowl size 600mm x 450mmx220mm including waste coupling and waste pipe complete all as specified and directed by Engr-in-Charge

M & L granite (telephone black) work 16 to 20 mm thick (table rubbed and polished) in cooking platforms/ counters/vanities/ Skirtings/ Window frames etc and like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engr-in-Charge

S&F, CP 20 mm bore stop valves, cast copper along screwed down high pressure with crutch and butterfly handles renewed both ends complete all as specified and directed by Engr-in-charge.

S&F, chromium plated 15mm bore stop valves, cast copper along screwed down high pressure with crutch and butterfly handles renewed both ends complete all as specified and directed by Engr-in-charge.

S&F concealed chromium plated stop valves, cast copper alloy 15 mm bore screwed down high pressure with quarter turn type for iron pipe or for union and complete all as specified and directed by Engineer-in-Charge.

S&F Single lever extended basin/Sink mixer cast copper alloy, chromium plated 15mm dia of bore complete all as specified and directed by Engr-in-Charge

S & F 15mm dia brass CP mixer for mixing hot & cold water screwed down for iron pipe with spouts to shower and fixed complete all as specified and directed by Engr-in-Charge

S&F 1000 ltrs capacity Rotational moulding water storage tank comprising 3 layer and white in colour, hoisted and fixed in position all as specified in SSR Pt I complete all as specified and directed by Engr-in-Charge

S & F 20 mm ball brass valve high pressure, with polythelene float and flynut complete, screwed to iron pipe complete all as specified and directed by Engr-in-Charge

S&F PVC Connection 15mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engr-in-Charge

S&F for 125/110 mm dia PVC (SWR) floor trap/multifloor trap/gully trap, plain with grating including jointing with solvent cement fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engr in Charge

S&F for 75 mm dia PVC (SWR) floor trap/multifloor trap/gully trap, plain with grating including jointing with solvent cement fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engr in Charge

S&F, chromium plated 15mm bib taps cast copper alloy with crutch or butterfly handles, screwed down complete all as specified and directed by Engr-in-Charge

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, jointed with solvent fixed to wall or laid in trenches with matching PVC SWR rings including cutting holes and making good the disturbed portion with PCC (1:2:4) type B0 including clamps and bends/Tee/elbow/ branch piece complete all as specified & directed by Engr-in-Charge.

S&F 110 mm bore PVC (SWR) PVC (SWR) bends any radius complete all as specified & directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR) PVC (SWR) junction single, (Single T) equal or unequal complete all as specified & directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR)PVC (SWR) vent cowl complete all as specified & directed by Engr-in-Charge.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, jointed with solvent fixed to wall or laid in trenches with matching PVC SWR rings including cutting holes and making good the disturbed portion with PCC (1:2:4) type B0 including clamps and bends complete all as specified & directed by Engr-in-Charge.

S&F 75 mm bore PVC (SWR) PVC (SWR) junction single, (Single T) equal or unequal complete all as specified & directed by Engr-in-Charge.

M&L rain water pipies of 110 mm PVC (SWR) pipes single socked in any length with rubber ring joints fixed to walls all as specified and directed by Engr-in-charge.

S&F PVC (SWR) Bends 110 mm dia as complete all as specified and directed by Engineer-in-charge.

OVERLAY- PU BASED ELASTOMERIC LIQUIED MEMBRANE SYSTEM FOR EXPOSED ROOF : Providing and applying polyurethane liquid roof waterproofing with improved water ponding capability, elastomeric high build liquid membrane for concrete roofs for exterior wall and exposed surface with solid content not less than 80% and solar reflective index not less than 106 as per (ASTM E1980-19)/tear strength ~20 N/mm (Free film, 14 days, +30 degree C) (ASTM D624) and tensile strength >= 2 N/mm2 (ASTM D4541), elongation 350 to 400% as per ASTM D412 and crack bridging ability upto 2mm. (a) After proper surface preparation, Apply one coat of Primer for PU coating as per manufacturers specification. (b) Apply 1st coat of ShaliUrethane® BTD (white) @ 650 gm / m²(minimum) or equivalent by brush / roller while prime surface is tacky, Spread waterproofing reinforced Glass Fiber mash of 45 GSM with overlaps of 50 mm in both directions when the surface is still tacky. Allow 1st coat to dry. (c ) Apply 2nd & 3rd coat of ShaliUrethane® BTD (white) @ 650 gm / m² (minimum) or equivalent by brush/roller. Make : Fosroc/Sika/Choksey/Bostik/STP/ Asian Paints/Berger Paints Note : (i) The Minimum dry film thickness (DFT) of roof treatment shall be 1.5mm if any shortfall in thickness of above treatment the same shall be achieved by additional coat. (ii) The procurement of material and execution of the work of water proofing treatment shall be carried out by authorised applicator approved by GE. (iii) The manufacturer/authorised applicator shall give a warranty for the performance & durability for 10 years.

Supplying and laying of CPVC pipes of dia 20 mm SDR 11 & Plain CPVC SDR 11 inlcuding all fittings i.e.Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specified and directed by Engr in Charge.

Supplying and laying of CPVC pipes of dia 25 mm SDR 11 & Plain CPVC SDR 11 inlcuding all fittings i.e.Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specified and directed by Engr in Charge.

Supplying and laying of CPVC pipes of dia 32 mm SDR 11 & Plain CPVC SDR 11 inlcuding all fittings i.e.Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specified and directed by Engr in Charge.

S&F 40 mm bore PVC low density (LDPE) Pipe of pressure 6 Kg/CM2 fixed to wall or laid in floor including stacking GI clamps complete all as specified and directed by Engineer in Charge

S&F 18 mm thick high Density High Moisture Resistant (HDHMR) exterior Grade Board with both side white balancing (BSB) with density of 850 Kg/cu.m complete all as specified and directed. Make : Action Tesa/ Greenpanel/Century Note : (i) Board on back side wall will be fixed with minimum 5mm PVC spacers. The payment for the same deemed to be included in the quoted unit rates. (ii) Rates of following items are included : (i) Auto closing hinges 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree. (ii) Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs. (iii) Tower bolts 250mm long of stainless steel 304 finished/of outer plate metal matt finished. (iv) D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 200mm long matt finished. (v) Butt hinges of size 75mm of stainless steel 202 Grade finished/of outer plate metal. (vi) Piano/continuous hinge of size 19 mm stainless steel complete all as specified. Make : Action Tesa/Greenply/Century

S&F wall hung WC with UF Seat Cover ,Hinges, Accessories Set Size 640 x 360 x 765 mm white complete, including concealed body flushing cistern with hinging arrangement, complete all as specified and directed by Engineer-in-Charge.

S&F vitreous china wash hand basin white flat back of size 550mm X 400mm (table top/corner or any type), fixed with a set of cast iron brackets including cutting and pinning in ends of brackets to wall and providing 15mm size CP pillar tap, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without letter "Hot or cold'' with long scrwed shanks and fly nuts, 32mm dia brass chromium plated waste fittings 450mm long PVC connection of 15mm size with PTMT nuts and 40mm dia waste pipe complete all as specified and directed by Engineer - in - Charge.

S&F CP grating of size 100mm dia complete all as specified and directed by Engr-in-Charge

S&F Soap dish CP brass 100mm dia (round or oval) fixed to walls or dados complete all as specified and directed by Engineer - in - Charge.

S&F CP shower rose 125mm size and 15mm dia with 450 mm long arm complete all as specified and directed by Engr-in-Charge

S&F CP Tubular towel rail, 20mm dia, D type, 600mm long between flanges fixed with CP brass screws complete all as specified and directed by Engr-in-Charge

S&F in repair 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engr-in-Charge

Supply and fixing drapery curtain rod 25mm dia, fancy type, fabricated out of anodised aluminium alloy sheet not less than 20 guage, including brackets and pair of decorated end knobs (finials), stop roller etc, pretreated powder coated natural color complete (size of each curtain not less than 1.20m) all as specified & directed by Engineer-in- charge.

S&F premium quality stainless steel peg stay of 6 hooks fixed with stainless steel screws complete all as specified and directed by Engr-in-Charge

S&F Health faucet to EWC, CP brass with minimum 1000mm long CP flexible pipe, connection etc., complete all as specified and directed by Engineer-in-Charge.

M&L for surface dressing n exc 15 cm deep in soft/loose soil complete all as per specified and directed by Engineer in Charge

M&L for hardcore of broken bricks gauge exc 63mm nit n.exc 100mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rolled /rammed to true surface complete all as specified and directed by Engr-in-Charge

M&L 75 mm thick cement concrete type D2, 1:4:8 (Using 40mm graded stone aggregate) filling and mass concrete complete all as specified and directed by Engr-in-Charge

M&L Colured 300x 300x15 mm/400x400x15mm 1cm thick Non Skid (Endura tiles/Hi Traffic grip tiles) set jointed and pointed in neat cement slurry in floors over 20 mm of screed bed in CM 1:4 including coping at edges in PCC Type B1 (1:2:4) complete all as specified and directed by Engr-in-Charge

DWCPE(SN8) 150mm nominal dia pipes as per IS-16098 (Part-II) laid in trenches on and including 100 mm thick bed comprising of well compacted clean poorly graded garvel/sand mixture with little/ no fines to require slope, Includes all accesories/fittings/jointing ring, jointing and testing complete all as sped and directed by Engr in Charge.

M&L for PCC 1:3:6 type C-2 (40mm graded stone agg.) concrete in surface channels and drains complete all as specified and directed by Engr-in-Charge

Supply and Fix LLDPE Anaerobic Underground septic tank of capacity 4000 Ltrs, 02 Nos of chambers, made of ratation moulding application LLDPE materials having MFI > 4.0, density > 930 kg/m3, tensile stress at yield : > Mpa, tensile strain at yield: < 25%, tensile strain at break: > 80%, thickness of wall > 7mm including necessary inlet and outlet pipe of 2 metre length with submerged pipe tee, vent pipe of 2 metre length and 50mm dia, designed to carry sewage and salvage water with up flow filter chamber and other performance requirement and test certificates as per BMBA PC-4: 2011 including necessary excavation and earthe works, footings of approprate size and thickness in plain cement concrete works in cement concrete (M7.5) using 40mm graded crushed stone aggregates complete all as specified and as directed.

M&L for construction of soakage well of size (1.8 metre dia x 3.0 metre effective depth) as per drawing NO BTD-804 sheet No 1/1 (Drawing of Chief Engineer Bathinda Zone) including necessary earth work in any type of soil, PCC lean concrete in M7.5(Nominal Mix) using 40mm nominal size graded crushed stone aggregate as in foundation, RCC M25 (Design Mix) using 20 mm graded crushed stone aggreagte as in slab, manhole cover in precast RCC M-25 (Design Mix), RCC band in M25(Design Mix) using 20mm nominal size coarse aggregate, random rubble dry masonry, coursed stone block masonry in 1:6 cement mortar, brick rubble filling, inlet pipe of cast iron of 150 mm nominal dia asper IS 1729 : 2002 and length upto 4 metre each, reinforcement of grade as specified, other structural details as per drawings and specifications, complete all as specified and directed.

M&L providing precast cement concrete in RCC (1:2:4) type B-1 with 20 mm graded aggregate in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces setting in mortar (1:4) complete with joints to match complete all as specified and directed by Engr-in-Charge

M & L for concealed conduit point wiring complete for light/ fan on independent /combine board with cable 2.5 sqmm (Nominal area) FRLSH PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC Concealed conduit pipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for modular metal flush boxes suitable length and Min 1.6 mm thickness, Min 51 mm depth for mounting, switches, sockets,fan regulator with modular cover plate with frame and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 2.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced by the Engineer in charge.

All as per Srl item No -99 here in before but for one switch socket combination 5/6 amp on independent board complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No -99 here in before but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 99 here in before but for one switch socket combinationt 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 99 here in before but for Industrial Socket on independent board with copper conductor 4 Sqmm complete all as specified and directed by Engineer - in - Charge.

S & F modular switch 5/6 Amps single pole one way,one module complete all as specified and directed by Engineer - in - Charge.

S & F Modular switch 1 way 16A, with box complete all as specified and directed by Engineer - in - Charge.

S & F modular Socket, 16A - 2/3 pin combined 2 Module complete all as specified and directed by Engineer - in - Charge.

S & F modular socket outlet 5 pin 6 Amps flush type complete all as specified and directed by Engineer - in - Charge.

S & F modular stepped type, fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer - in - Charge

S & F ceiling rose surface bakelite three terminals complete all as specified and directed by Engineer - in - Charge.

Supply and fix Industrial socket metal clad plug and socket with MCBs single pole 20 Amp complte all as specified and directed by Engineer - in - Charge.

S & F light fitting with LED batten 20W LED batten with 'Eye Soft' technology & glarefree diffuser for perfect application in modern homes or aliminium housing and integrated electronic driver, 20 watt, 50 Hz , 6500K, and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

S&F security light fitting LED TYPE 20 watt with all necessary acessories, Clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in - Charge

Supply and fixing ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed by Engr-in-Charge

S&F Heavy duty metal body exahust fan of 300 mm sweep ,240 volt,copper winding, complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to distubed wall in cement mortar (1 :4) white washing matching with existing colour etc. complete all as specified and directed by Engr-in-Charge

Supply and fix iron body desert cooler alongiwth stand electric driven (single phase), having nominal air flow capacity of 5000 CuM per hour (or nearest size), honeycomb pad(24' x 24') , water tank 80L capacity, thickness of sheet 20 gauge (minimum) all as specified and directed by Engr-in-Charge.

Supply and fix electric water heater, storage type plastic & steel metal body with glass coating SS tank and heating element upto 2 KW capacity 50 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed by Engr-in-Charge

Supply and fix Valve, stop, screwed,20 mm (3/4”) dia pipe complete all as specified and directed by Engineer - in - Charge.

Supply and fix Valve, stop, screwed,25 mm (1”) dia pipe complete all as specified and directed by Engineer - in - Charge.

S & F MCB ‘B’ series type suitable for 240 volts,10 KA, AC supply 6 to 32 Amps , single pole (SP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in repairs sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 12 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S & F in repairs sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 04 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S & F in repairs MCB ‘C’ series type suitable for 240 volts, AC supply 5 to 40 Amps , single pole & neutrtal with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in PVC conduict dia 20mm “medium quality” conduit including 6.00 Sq mm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge.

M & L for Earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level , connecting to GI earth lead 4 mm dia GI earth wire ,by means of bolts,nuts and washers of GI and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20 mm grade stone aggregate with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 gs /Sqmm ) and frame of angle iron 25mmX25mmX6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape ,GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmX 8 mm FI with fixing arrangement ,funnel, wire mesh and earth work inhard dense soil ,returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electric plate no.3 of SSR part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on completion all as specified and directed by Engr -In - Charge.

Supply and lay jointing and testing and commissioning in replacement of 25 Sqmm x 4 core XLPE insulated, screened , PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed by engineer in charge.

Supply, Laying DWC pipe size 77 mm OD/ 63 mm ID by Excavated Method complete all as specified and directed by Engr-in-Charge

M & L for boring hole under road,pavement , hard standing by trenchesless for laying DWC pipe suitable for outer dia of cable passing without damaging Road / Plinth /Floor complete all as specified and directed by Engr-in-Charge

M&L for steel water tubing medium grade of size 25 mm bore with all fittings laid in trenches or fixed to wall or floor.complete all as specified and directed by Engineer-in-charge.

Supply and laying GI pipe medium grade ISI marked 20mm dia including all fittings in old/new position complete all as specified and directed by Engr-in-Charge

Supply and Fixing Gun Metal gate valves with iron wheel head,screwed 20 mm both ends for iron pipe,ISI marked, as per IS: 778 complete all as specified and directed by Engr-in-Charge

Supply and Fixing Gun Metal gate valves with iron wheel head,screwed 25 mm both ends for iron pipe,ISI marked, as per IS: 778 complete all as specified and directed by Engr-in-Charge

M & L cutting existing GI water turbing of size 100 mm bore for alternation or addition including screwing/threading and jointing with suitable size GI socket complete all as specified and as directed by Engineer-in-Charge.

Please Enable Macros to View BoQ information